Effects of increasing levels of pea hulls in the diet on productive performance, development of the gastrointestinal tract, and nutrient retention of broilers from one to eighteeen days of age

The effects of inclusion of pea hulls (PH) in the diet on growth performance, development of the gastrointestinal tract and nutrient retention were studied in broilers from 1 to 18d of age. There were a control diet based on low fibre ingredients (69.3 total dietary fibre (16.1g crude fibre/kg)) and three additional diets that resulted from the dilution of the basal diet with 25, 50 and 75g PH/kg (81.2, 93.2, and 105.1g total dietary fibre/kg diet, respectively). Each treatment was replicated six times and the experimental unit was a cage with 12 chicks. Growth performance, development of the gastrointestinal tract and the coefficients of total tract apparent retention (CTTAR) of nutrients were recorded at 6, 12 and 18d of age. In addition, jejunal morphology was measured at 12 and 18d and the coefficients of apparent ileal digestibility (CAID) of nutrients at 18d of age. Pea hulls inclusion affected all the parameters studied. The inclusion of 25 and 50g PH/kg diet improved growth performance as compared to the control diet. The relative weight (g/kg body weight) of proventriculus (P≤0.01), gizzard (P≤0.001) and ceca (P≤0.05) increased linearly as the level of PH in the diet increased. The inclusion of PH affected quadratically (P≤0.01) villus height:crypt depth ratio with the highest value shown at 25g PH/kg. In general, the CTTAR and CAID of nutrients increased linearly and quadratically (P≤0.05) with increasing levels of PH, showing maximum values with PH level between 25 and 50g/kg diet. We conclude that the size of the digestive organs increases with increasing levels of PH in the diet. In general, the best performance and nutrient digestibility values were observed with levels of PH within the range of 25 and 50g/kg. Therefore, young broilers have a requirement for a minimum amount of dietary fibre. When pea hulls are used as a source of fibre, the level of total dietary fibre required for optimal performance is within the range of 81.2–93.2g/kg diet (25.6–35.0g crude fibre/kg diet). An excess of total dietary fibre (above 93.2g/kg diet) might reduce nutrient digestibility and growth performance to values similar to those observed with the control diet.

Towards the development of poly (phenylene sulphide) based nanocomposites with enhanced mechanical, electrical and tribological properties

Novel poly(phenylene sulphide) (PPS) nanocomposites reinforced with an aminated derivative (PPS-NH2) covalently attached to acid-treated single-walled carbon nanotubes (SWCNTs) were prepared via simple melt-blending technique. Their morphology, viscoelastic behaviour, electrical conductivity, mechanical and tribological properties were investigated. Scanning electron microscopy revealed that the grafting process was effective in uniformly dispersing the SWCNTs within the matrix. The storage and loss moduli as a function of frequency increased with the SWCNT content, tending to a plateau in the low-frequency regime. The electrical conductivity of the nanocomposites was considerably enhanced in the range 0.1?0.5 wt% SWCNTs; electrical and rheological percolation thresholds occurred at similar nanotube concentrations. Mechanical tests demonstrated that with only 1.0 wt% SWCNTs the Young's modulus and tensile strength of the matrix improved by 51 and 37%, respectively, without decrement in toughness, ascribed to a very efficient load transfer. A moderate decrease in the friction coefficient and a 75% reduction in wear rate were found for the abovementioned nanotube loading, indicating that PPS-NH2-g-SWCNTs are good tribological additives for thermoplastic polymers. Based on the promising results obtained in this work, it is expected that these nanofillers will be used to develop high-performance thermoplastic/CNT nanocomposites for structural applications.

Influence of PH3 exposure on silicon substrate morphology in the MOVPE growth of III-V on silicon multijunction solar cells

Dual-junction solar cells formed by a GaAsP or GaInP top cell and a silicon bottom cell seem to be attractive candidates to materialize the long sought-for integration of III-V materials on silicon for photovoltaic applications. One of the first issues to be considered in the development of this structure will be the strategy to create the silicon emitter of the bottom subcell. In this study, we explore the possibility of forming the silicon emitter by phosphorus diffusion (i.e. exposing the wafer to PH3 in a MOVPE reactor) and still obtain good surface morphologies to achieve a successful III-V heteroepitaxy as occurs in conventional III-V on germanium solar cell technology. Consequently, we explore the parameter space (PH3 partial pressure, time and temperature) that is needed to create optimized emitter designs and assess the impact of such treatments on surface morphology using atomic force microscopy. Although a strong degradation of surface morphology caused by prolonged exposure of silicon to PH3 is corroborated, it is also shown that subsequent anneals under H-2 can recover silicon surface morphology and minimize its RMS roughness and the presence of pits and spikes.

Development of One Meter Long Double-Sided CeO2 Buffered Ni-5at.W Templates by Reel-to-Reel Chemical Solution Deposition Route

High performance long-length coated conductors fabricated using various techniques have attracted a lot of interest recently. In this work, a reel-to-reel design for depositing double-sided coatings on long-length flexible metallic tapes via a chemical solution method is proposed and realized. The major achievement of the design is to combine the dip coating and drying processes in order to overcome the technical difficulties of dealing with the wet films on both sides of the tape. We report the successful application of the design to fabricate a one-meter-long double side coated CeO2/Ni-5at%W template. The CeO2 films on both sides exhibit a dense, crack-free morphology, and a high fraction of cube texture on the surface. Homogeneity studies on global texture over the length also reveal that the average full width at half maximum values of the in-plane and out-of-plane orientation on the CeO2 layer are 7.2 ° and 5.8° with standard deviation of 0.26° and 0.34°, respectively, being indicative of the high quality epitaxial growth of the films prepared in the continuous manner. An all chemical solution derived YBCOLow-TFA/Ce0.9La0.1O2 /Gd2Zr2O7/CeO2 structure is obtained on a short sample, demonstrating the possibility of producing long-length texture templates for coated conductors by this low cost deposition route.

Mathematical development of stress-strain law for rock block contacts

The fracture behavior of rock block contacts has been studied for many years. Unfortunately, up to now, there is not a rigorous formulation or a solid theoretical foundation to support it. A mathematical development to represent the failure mechanism which occurs in the contacts between rock blocks is presented to evaluate the performance of breaking mechanism of such blocks relating it to the morphology of the contact and mechanical parameters of the material. The examined framework includes the evaluation of the surface roughness of first order in the failure mechanism of the granular particles of large size and the development of a theoretical model describing the morphology of the contact between rock blocks.