Rapid sizing tool for a low cost university microsatellite structure subsystem

In recent decays university class small satellites are creating many opportunities for space research and professional trainings while at the same time responding to constrained budgets. In this work the main focus is on developing a simple and rapid structural sizing tool considering the main objectives of a low cost university class microsatellite project. In satellite projects, structure subsystem is one of the influential subsystems as a driver of the cost and acceptance of the final design. At the first steps of such projects there is no confirmed data regarding the launch vehicle or even in some cases there is no data for the satellite payload. Due to these facts, developing simple sizing tools at conceptual design phase for obtaining an over view of the effect of different variables is useful before entering complex calculations in detailed design phases. In this study, after developing a simple analytical model of satellite structure subsystem, a design space is evaluated with practical boundaries considering mass and dimensions constraints of such projects. The results are useful to give initial insight to establish the system level structural sizing

Multiobjective optimization applied to structural sizing of low cost university-class microsatellite projects

In recent years, there has been continuing interest in the participation of university research groups in space technology studies by means of their own microsatellites. The involvement in such projects has some inherent challenges, such as limited budget and facilities. Also, due to the fact that the main objective of these projects is for educational purposes, usually there are uncertainties regarding their in orbit mission and scientific payloads at the early phases of the project. On the other hand, there are predetermined limitations for their mass and volume budgets owing to the fact that most of them are launched as an auxiliary payload in which the launch cost is reduced considerably. The satellite structure subsystem is the one which is most affected by the launcher constraints. This can affect different aspects, including dimensions, strength and frequency requirements. In this paper, the main focus is on developing a structural design sizing tool containing not only the primary structures properties as variables but also the system level variables such as payload mass budget and satellite total mass and dimensions. This approach enables the design team to obtain better insight into the design in an extended design envelope. The structural design sizing tool is based on analytical structural design formulas and appropriate assumptions including both static and dynamic models of the satellite. Finally, a Genetic Algorithm (GA) multiobjective optimization is applied to the design space. The result is a Pareto-optimal based on two objectives, minimum satellite total mass and maximum payload mass budget, which gives a useful insight to the design team at the early phases of the design.

Optimum sizing of bare-tape tethers for de-orbiting satellites at end of mission

De-orbiting satellites at end of mission would prevent generation of new space debris. A proposed de-orbit technology involves a bare conductive tape-tether, which uses neither propellant nor power supply while generating power for on-board use during de-orbiting. The present work shows how to select tape dimensions for a generic mission so as to satisfy requirements of very small tether-to-satellite mass ratio mt/MS and probability Nf of tether cut by small debris, while keeping de-orbit time tf short and product tf ×× tether length low to reduce maneuvers in avoiding collisions with large debris. Design is here discussed for particular missions (initial orbit of 720 km altitude and 63° and 92° inclinations, and 3 disparate MS values, 37.5, 375, and 3750 kg), proving it scalable. At mid-inclination and a mass-ratio of a few percent, de-orbit time takes about 2 weeks and Nf is a small fraction of 1%, with tape dimensions ranging from 1 to 6 cm, 10 to 54 μμm, and 2.8 to 8.6 km. Performance drop from middle to high inclination proved moderate: if allowing for twice as large mt/MS, increases are reduced to a factor of 4 in tf and a slight one in Nf, except for multi-ton satellites, somewhat more requiring because efficient orbital-motion-limited electron collection restricts tape-width values, resulting in tape length (slightly) increasing too.

Rapid method for spacecraft sizing

In this paper, a rapid method for spacecraft sizing is presented. This method is useful in both the conceptual and preliminary design phases of scientific and communication satellites. The aim of this method is to provide a sizing procedure similar to the ones used in the design of aircraft; actually by determining the mass of all the spacecraft subsystems. In the Introduction, the importance of an accurate initial mass budget in the design of satellites is emphasized. Literature about this topic is not very extensive and most of the existing methods have been recapitulated. The methodology followed in the proposed procedure for spacecraft mass sizing is based on these methods. Data from 26 existing satellites have been considered to obtain correlations between each subsystem mass and the mass of the whole spacecraft.