A two-dimensional finite element model of front surface current flow in cells under non-uniform, concentrated illumination

A two-dimensional finite element model of current flow in the front surface of a PV cell is presented. In order to validate this model we perform an experimental test. Later, particular attention is paid to the effects of non-uniform illumination in the finger direction which is typical in a linear concentrator system. Fill factor, open circuit voltage and efficiency are shown to decrease with increasing degree of non-uniform illumination. It is shown that these detrimental effects can be mitigated significantly by reoptimization of the number of front surface metallization fingers to suit the degree of non-uniformity. The behavior of current flow in the front surface of a cell operating at open circuit voltage under non-uniform illumination is discussed in detail.

Reduction of front-metallization grid shading in concentrator cells through laser micro-grooved cover glass

Concentrator solar cell front-grid metallizations are designed so that the trade-off between series resistance and shading factor (SF) is optimized for a particular irradiance. High concentrator photovoltaics (CPV) typically requires a metallic electrode pattern that covers up to 10% of the cell surface. The shading effect produced by this front electrode results in a significant reduction in short-circuit current (I SC) and hence, in a significant efficiency loss. In this work we present a cover glass (originally meant to protect the cell surface) that is laser-grooved with a micrometric pattern that redirects the incident solar light towards interfinger regions and away from the metallic electrodes, where they would be wasted in terms of photovoltaic generation. Quantum efficiency (QE) and current (I)-voltage (V) characterization under concentration validate the proof-of-concept, showing great potential for CPV applications

Analysis of the behavior of multijunction solar cells under high irradiance Gaussian light profiles showing chromatic aberration with emphasis on tunnel junction performance

In this work, we explain the behavior of multijunction solar cells under non-uniform (spatially and in spectral content) light profiles in general and in particular when Gaussian light profiles cause a photo-generated current density, which exceeds locally the peak current density of the tunnel junction. We have analyzed the implications on the tunnel junction's limitation, that is, in the loss of efficiency due to the appearance of a dip in the I–V curve. For that, we have carried out simulations with our three-dimensional distributed model for multijunction solar cells, which contemplates a full description of the tunnel junction and also takes into account the lateral resistances in the tunnel junction. The main findings are that the current density photo-generated spreads out through the lateral resistances of the device, mainly through the tunnel junction layers and the back contact. Therefore, under non-uniform light profiles these resistances are determinant not only to avoid the tunnel junction's limitation but also for mitigating losses in the fill factor. Therefore, taking into account these lateral resistances could be the key for jointly optimizing the concentrator photovoltaic system (concentrator optics, front grid layout and semiconductor structure)

Desarrollo de estructuras nanofotonicas de campo cercano para intensificacion localizada de luz en celulas solares de banda intermedia - Near-field nanophotonic structures for localized light enhancement in intermediate band solar cells

This doctoral thesis explores some of the possibilities that near-field optics can bring to photovoltaics, and in particular to quantum-dot intermediate band solar cells (QD-IBSCs). Our main focus is the analytical optimization of the electric field distribution produced in the vicinity of single scattering particles, in order to produce the highest possible absorption enhancement in the photovoltaic medium in their surroundings. Near-field scattering structures have also been fabricated in laboratory, allowing the application of the previously studied theoretical concepts to real devices. We start by looking into the electrostatic scattering regime, which is only applicable to sub-wavelength sized particles. In this regime it was found that metallic nano-spheroids can produce absorption enhancements of about two orders of magnitude on the material in their vicinity, due to their strong plasmonic resonance. The frequency of such resonance can be tuned with the shape of the particles, allowing us to match it with the optimal transition energies of the intermediate band material. Since these metallic nanoparticles (MNPs) are to be inserted inside the cell photovoltaic medium, they should be coated by a thin insulating layer to prevent electron-hole recombination at their surface. This analysis is then generalized, using an analytical separation-of-variables method implemented in Mathematica7.0, to compute scattering by spheroids of any size and material. This code allowed the study of the scattering properties of wavelengthsized particles (mesoscopic regime), and it was verified that in this regime dielectric spheroids perform better than metallic. The light intensity scattered from such dielectric spheroids can have more than two orders of magnitude than the incident intensity, and the focal region in front of the particle can be shaped in several ways by changing the particle geometry and/or material. Experimental work was also performed in this PhD to implement in practice the concepts studied in the analysis of sub-wavelength MNPs. A wet-coating method was developed to self-assemble regular arrays of colloidal MNPs on the surface of several materials, such as silicon wafers, amorphous silicon films, gallium arsenide and glass. A series of thermal and chemical tests have been performed showing what treatments the nanoparticles can withstand for their embedment in a photovoltaic medium. MNPs arrays are then inserted in an amorphous silicon medium to study the effect of their plasmonic near-field enhancement on the absorption spectrum of the material. The self-assembled arrays of MNPs constructed in these experiments inspired a new strategy for fabricating IBSCs using colloidal quantum dots (CQDs). Such CQDs can be deposited in self-assembled monolayers, using procedures similar to those developed for the patterning of colloidal MNPs. The use of CQDs to form the intermediate band presents several important practical and physical advantages relative to the conventional dots epitaxially grown by the Stranski-Krastanov method. Besides, this provides a fast and inexpensive method for patterning binary arrays of QDs and MNPs, envisioned in the theoretical part of this thesis, in which the MNPs act as antennas focusing the light in the QDs and therefore boosting their absorption

Electromagnetic Instability Studies in Fusion Plasmas Edge

Este trabajo esta dedicado al estudio de las estructuras macroscópicas conocidas en la literatura como filamentos o blobs que han sido observadas de manera universal en el borde de todo tipo de dispositivos de fusión por confinamiento magnético. Estos filamentos, celdas convectivas elongadas a lo largo de las líneas de campo que surgen en el plasma fuertemente turbulento que existe en este tipo de dispositivos, parecen dominar el transporte radial de partículas y energía en la región conocida como Scrape-off Layer, en la que las líneas de campo dejan de estar cerradas y el plasma es dirigido hacia la pared sólida que forma la cámara de vacío. Aunque el comportamiento y las leyes de escala de estas estructuras son relativamente bien conocidos, no existe aún una teoría generalmente aceptada acerca del mecanismo físico responsable de su formación, que constituye una de las principales incógnitas de la teoría de transporte del borde en plasmas de fusión y una cuestión de gran importancia práctica en el desarrollo de la siguiente generación de reactores de fusión (incluyendo dispositivos como ITER y DEMO), puesto que la eficiencia del confinamiento y la cantidad de energía depositadas en la pared dependen directamente de las características del transporte en el borde. El trabajo ha sido realizado desde una perspectiva eminentemente experimental, incluyendo la observación y el análisis de este tipo de estructuras en el stellarator tipo heliotrón LHD (un dispositivo de gran tamaño, capaz de generar plasmas de características cercanas a las necesarias en un reactor de fusión) y en el stellarator tipo heliac TJ-II (un dispositivo de medio tamaño, capaz de generar plasmas relativamente más fríos pero con una accesibilidad y disponibilidad de diagnósticos mayor). En particular, en LHD se observó la generación de filamentos durante las descargas realizadas en configuración de alta _ (alta presión cinética frente a magnética) mediante una cámara visible ultrarrápida, se caracterizó su comportamiento y se investigó, mediante el análisis estadístico y la comparación con modelos teóricos, el posible papel de la Criticalidad Autoorganizada en la formación de este tipo de estructuras. En TJ-II se diseñó y construyó una cabeza de sonda capaz de medir simultáneamente las fluctuaciones electrostáticas y electromagnéticas del plasma. Gracias a este nuevo diagnóstico se pudieron realizar experimentos con el fin de determinar la presencia de corriente paralela a través de los filamentos (un parámetro de gran importancia en su modelización) y relacionar los dos tipos de fluctuaciones por primera vez en un stellarator. Así mismo, también por primera vez en este tipo de dispositivo, fue posible realizar mediciones simultáneas de los tensores viscoso y magnético (Reynolds y Maxwell) de transporte de cantidad de movimiento. ABSTRACT This work has been devoted to the study of the macroscopic structures known in the literature as filaments or blobs, which have been observed universally in the edge of all kind of magnetic confinement fusion devices. These filaments, convective cells stretching along the magnetic field lines, arise from the highly turbulent plasma present in this kind of machines and seem to dominate radial transport of particles and energy in the region known as Scrapeoff Layer, in which field lines become open and plasma is directed towards the solid wall of the vacuum vessel. Although the behavior and scale laws of these structures are relatively well known, there is no generally accepted theory about the physical mechanism involved in their formation yet, which remains one of the main unsolved questions in the fusion plasmas edge transport theory and a matter of great practical importance for the development of the next generation of fusion reactors (including ITER and DEMO), since efficiency of confinement and the energy deposition levels on the wall are directly dependent of the characteristics of edge transport. This work has been realized mainly from an experimental perspective, including the observation and analysis of this kind of structures in the heliotron stellarator LHD (a large device capable of generating reactor-relevant plasma conditions) and in the heliac stellarator TJ-II (a medium-sized device, capable of relatively colder plasmas, but with greater ease of access and diagnostics availability). In particular, in LHD, the generation of filaments during high _ discharges (with high kinetic to magnetic pressure ratio) was observed by means of an ultrafast visible camera, and the behavior of this structures was characterized. Finally, the potential role of Self-Organized Criticality in the generation of filaments was investigated. In TJ-II, a probe head capable of measuring simultaneously electrostatic and electromagnetic fluctuations in the plasma was designed and built. Thanks to this new diagnostic, experiments were carried out in order to determine the presence of parallel current through filaments (one of the most important parameters in their modelization) and to related electromagnetic (EM) and electrostatic (ES) fluctuations for the first time in an stellarator. As well, also for the first time in this kind of device, measurements of the viscous and magnetic momentum transfer tensors (Reynolds and Maxwell) were performed.

A Light-Weight On-Chip Monitoring Network for Dynamic Adaptation and Calibration

Current nanometer technologies suffer within-die parameter uncertainties, varying workload conditions, aging, and temperature effects that cause a serious reduction on yield and performance. In this scenario, monitoring, calibration, and dynamic adaptation become essential, demanding systems with a collection of multi purpose monitors and exposing the need for light-weight monitoring networks. This paper presents a new monitoring network paradigm able to perform an early prioritization of the information. This is achieved by the introduction of a new hierarchy level, the threshing level. Targeting it, we propose a time-domain signaling scheme over a single-wire that minimizes the network switching activity as well as the routing requirements. To validate our approach, we make a thorough analysis of the architectural trade-offs and expose two complete monitoring systems that suppose an area improvement of 40% and a power reduction of three orders of magnitude compared to previous works.

On-chip Monitoring: A Light-Weight Interconnection Network Approach

Current nanometer technologies are subjected to several adverse effects that seriously impact the yield and performance of integrated circuits. Such is the case of within-die parameters uncertainties, varying workload conditions, aging, temperature, etc. Monitoring, calibration and dynamic adaptation have appeared as promising solutions to these issues and many kinds of monitors have been presented recently. In this scenario, where systems with hundreds of monitors of different types have been proposed, the need for light-weight monitoring networks has become essential. In this work we present a light-weight network architecture based on digitization resource sharing of nodes that require a time-to-digital conversion. Our proposal employs a single wire interface, shared among all the nodes in the network, and quantizes the time domain to perform the access multiplexing and transmit the information. It supposes a 16% improvement in area and power consumption compared to traditional approaches.

Electromagnetic analysis of periodic structures under a waveguide viewpoint

The fundamental objective of this Ph. D. dissertation is to demonstrate that, under particular circumstances which cover most of the structures with practical interest, periodic structures can be understood and analyzed by means of closed waveguide theories and techniques. To that aim, in the first place a transversely periodic cylindrical structure is considered and the wave equation, under a combination of perfectly conducting and periodic boundary conditions, is studied. This theoretical study runs parallel to the classic analysis of perfectly conducting closed waveguides. Under the light shed by the aforementioned study it is clear that, under certain very common periodicity conditions, transversely periodic cylindrical structures share a lot of properties with closed waveguides. Particularly, they can be characterized by a complete set of TEM, TE and TM modes. As a result, this Ph. D. dissertation introduces the transversely periodic waveguide concept. Once the analogies between the modes of a transversely periodic waveguide and the ones of a closed waveguide have been established, a generalization of a well-known closed waveguide characterization method, the generalized Transverse Resonance Technique, is developed for the obtention of transversely periodic modes. At this point, all the necessary elements for the consideration of discontinuities between two different transversely periodic waveguides are at our disposal. The analysis of this type of discontinuities will be carried out by means of another well known closed waveguide method, the Mode Matching technique. This Ph. D. dissertation contains a sufficient number of examples, including the analysis of a wire-medium slab, a cross-shaped patches periodic surface and a parallel plate waveguide with a textured surface, that demonstrate that the Transverse Resonance Technique - Mode Matching hybrid is highly precise, efficient and versatile. Thus, the initial statement: ”periodic structures can be understood and analyzed by means of closed waveguide theories and techniques”, will be corroborated. Finally, this Ph. D. dissertation contains an adaptation of the aforementioned generalized Transverse Resonance Technique by means of which the analysis of laterally open periodic waveguides, such as the well known Substrate Integrated Waveguides, can be carried out without any approximation. The analysis of this type of structures has suscitated a lot of interest in the recent past and the previous analysis techniques proposed always resorted to some kind of fictitious wall to close the structure. vii Resumen El principal objetivo de esta tesis doctoral es demostrar que, bajo ciertas circunstancias que se cumplen para la gran mayoría de estructuras con interés práctico, las estructuras periódicas se pueden analizar y entender con conceptos y técnicas propias de las guías de onda cerradas. Para ello, en un primer lugar se considera una estructura cilíndrical transversalmente periódica y se estudia la ecuación de onda bajo una combinación de condiciones de contorno periódicas y de conductor perfecto. Este estudio teórico y de caracter general, sigue el análisis clásico de las guías de onda cerradas por conductor eléctrico perfecto. A la luz de los resultados queda claro que, bajo ciertas condiciones de periodicidad (muy comunes en la práctica) las estructuras cilíndricas transversalmente periódicas guardan multitud de analogías con las guías de onda cerradas. En particular, pueden ser descritas mediante un conjunto completo de modos TEM, TE y TM. Por ello, ésta tesis introduce el concepto de guía de onda transversalmente periódica. Una vez establecidas las similitudes entre las soluciones de la ecuación de onda, bajo una combinación de condiciones de contorno periódicas y de conductor perfecto, y los modos de guías de onda cerradas, se lleva a cabo, con éxito, la adaptación de un conocido método de caracterización de guías de onda cerradas, la técnica de la Resonancia Transversal Generalizada, para la obtención de los modos de guías transversalmente periódicas. En este punto, se tienen todos los elementos necesarios para considerar discontinuidades entre guías de onda transversalmente periódicas. El analisis de este tipo de discontinuidades se llevará a cabo mediante otro conocido método de análisis de estructuras cerradas, el Ajuste Modal. Esta tesis muestra multitud de ejemplos, como por ejemplo el análisis de un wire-medium slab, una superficie de parches con forma de cruz o una guía de placas paralelas donde una de dichas placas tiene cierta textura, en los que se demuestra que el método híbrido formado por la Resonancia Transversal Generalizada y el Ajuste Modal, es tremendamente preciso, eficiente y versátil y confirmará la validez de el enunciado inicial: ”las estructuras periódicas se pueden analizar y entender con conceptos y técnicas propias de las guías de onda cerradas” Para terminar, esta tésis doctoral incluye también una modificación de la técnica de la Resonancia Transversal Generalizada mediante la cual es posible abordar el análisis de estructuras periódica abiertas en los laterales, como por ejemplo las famosas guías de onda integradas en sustrato, sin ninguna aproximación. El análisis de este tipo de estructuras ha despertado mucho interés en los últimos años y las técnicas de análisis propuestas hasta ix el momento acostumbran a recurrir a algún tipo de pared ficticia para simular el carácter abierto de la estructura.

Developing front-end Web 2.0 technologies to access services, content and things in the future Internet

The future Internet is expected to be composed of a mesh of interoperable web services accessible from all over the web. This approach has not yet caught on since global user?service interaction is still an open issue. This paper states one vision with regard to next-generation front-end Web 2.0 technology that will enable integrated access to services, contents and things in the future Internet. In this paper, we illustrate how front-ends that wrap traditional services and resources can be tailored to the needs of end users, converting end users into prosumers (creators and consumers of service-based applications). To do this, we propose an architecture that end users without programming skills can use to create front-ends, consult catalogues of resources tailored to their needs, easily integrate and coordinate front-ends and create composite applications to orchestrate services in their back-end. The paper includes a case study illustrating that current user-centred web development tools are at a very early stage of evolution. We provide statistical data on how the proposed architecture improves these tools. This paper is based on research conducted by the Service Front End (SFE) Open Alliance initiative.

Magneto-optic current sensor with Faraday mirror for linear birefringence compensation

Fiber optic sensors have some advantages in subjects related with electrical current and magnetic field measurement. In spite of the optical fiber utilization advantages we have to take into account undesirable effects, which are present in real non-ideal optical fibers. In telecommunication and sensor application fields the presence of inherent and induced birefringence is crucial. The presence of birefringence may cause an undesirable change in the polarization state. In order to compensate the linear birefringence a promising method has been chosen. This method employs orthogonal polarization conjugation in the back propagation direction of the light wave in the fiber. A study and a simulation of an experimental setup are realized with the advantage of a significant sensitivity improvement.

New Intermediate band sulphide nanoparticles acting in the full visible light range spectra as an active photocatalyst

Nowadays one of the challenges of materials science is to find new technologies that will be able to make the most of renewable energies. An example of new proposals in this field are the intermediate-band (IB) materials, which promise higher efficiencies in photovoltaic applications (through the intermediate band solar cells), or in heterogeneous photocatalysis (using nanoparticles of them, for the light-induced degradation of pollutants or for the efficient photoevolution of hydrogen from water). An IB material consists in a semiconductor in which gap a new level is introduced [1], the intermediate band (IB), which should be partially filled by electrons and completely separated of the valence band (VB) and of the conduction band (CB). This scheme (figure 1) allows an electron from the VB to be promoted to the IB, and from the latter to the CB, upon absorption of photons with energy below the band gap Eg, so that energy can be absorbed in a wider range of the solar spectrum and a higher current can be obtained without sacrificing the photovoltage (or the chemical driving force) corresponding to the full bandgap Eg, thus increasing the overall efficiency. This concept, applied to photocatalysis, would allow using photons of a wider visible range while keeping the same redox capacity. It is important to note that this concept differs from the classic photocatalyst doping principle, which essentially tries just to decrease the bandgap. This new type of materials would keep the full bandgap potential but would use also lower energy photons. In our group several IB materials have been proposed, mainly for the photovoltaic application, based on extensively doping known semiconductors with transition metals [2], examining with DFT calculations their electronic structures. Here we refer to In2S3 and SnS2, which contain octahedral cations; when doped with Ti or V an IB is formed according to quantum calculations (see e.g. figure 2). We have used a solvotermal synthesis method to prepare in nanocrystalline form the In2S3 thiospinel and the layered compound SnS2 (which when undoped have bandgaps of 2.0 and 2.2 eV respectively) where the cation is substituted by vanadium at a ?10% level. This substitution has been studied, characterizing the materials by different physical and chemical techniques (TXRF, XRD, HR-TEM/EDS) (see e.g. figure 3) and verifying with UV spectrometry that this substitution introduces in the spectrum the sub-bandgap features predicted by the calculations (figure 4). For both sulphide type nanoparticles (doped and undoped) the photocatalytic activity was studied by following at room temperature the oxidation of formic acid in aqueous suspension, a simple reaction which is easily monitored by UV-Vis spectroscopy. The spectral response of the process is measured using a collection of band pass filters that allow only some wavelengths into the reaction system. Thanks to this method the spectral range in which the materials are active in the photodecomposition (which coincides with the band gap for the undoped samples) can be checked, proving that for the vanadium substituted samples this range is increased, making possible to cover all the visible light range. Furthermore it is checked that these new materials are more photocorrosion resistant than the toxic CdS witch is a well know compound frequently used in tests of visible light photocatalysis. These materials are thus promising not only for degradation of pollutants (or for photovoltaic cells) but also for efficient photoevolution of hydrogen from water; work in this direction is now being pursued.

Magnetic and electric current morphoiogy in the plasma ejected by a laser-irradiated foil

A quasisteady model for the plasma ablated from a thick foil by a laser pulse, at low $lln $ and R /A i within a low, narrow range, is given (4, is absorbed intensity, /zL wavelength, R focalspot radius). An approximate analytical solution is given for the two-dimensional plasma dynamics. At large magnetic Reynolds number Rm, the morphology of the magnetic field shows features in agreement with recent results for high intensities. Current lines are open: electric current flows toward the spot near its axis, then turns and flows away. The efficiency of converting light energy into electric energy peaks at Rm- 1, both the validity of the model. and accuracy of the solution are discussed, The neighborhood of the spot boundary is analyzed in detail by extending classical Prandtl-Meyer results.

Alfvén wave far field from steady-current tethers

We analyzed he Alfvén waves ignaturele ft behindi n the ionospherbe y orbiting insulatedt etherso peratinga s thrusterso r generatorws ith steadyc urrentsU. sing a recentd escription of tetherr adiationt o determineth e far field, we showt hat, at their leadinge dges,t heA lfv6n wingsh avea n Airy functionc rosswises tructureT. he field amplitudef alls off weakly as the inversec uber oot of the distancea longt he wavef ront.T he fronti tself, whichc arriesa negligible fractiono f the powerr adiateda sA lfven waves,b roadensp roportionallyto the cuber oot of that distanceW. e showt hatc ollisionadl ecayb ecomesim portanat t about1 03k m alongt he front.F or tethersl ongert han about2 km, the top andb ottoms tructures("wings")a re fully disjoint.

Interconexión monolítica de dispositivos fotovoltaicos basados en a-Si mediante ablación directa con fuentes láser ultravioleta

Resumen En la última década la tecnología láser se ha convertido en una herramienta imprescindible en la fabricación de dispositivos fotovoltaicos, muy especial¬mente en aquellos basados en tecnología de lámina delgada. Independiente¬mente de crisis coyunturales en el sector, la evolución en los próximos años de estas tecnologías seguirá aprovechándose de la flexibilidad y calidad de proceso de la herramienta láser para la consecución de los dos objetivos básicos que harán de la fotovoltaica una opción energética económicamente viable: la reducción de costes de fabricación y el aumento de eficiencia de los dispositivos. Dentro de las tecnologías fotovoltaicas de lámina delgada, la tecnología de dispositivos basados en silicio amorfo ha tenido un gran desarrollo en sistemas estándar en configuración de superestrato, pero su limitada efi¬ciencia hace que su supervivencia futura pase por el desarrollo de formatos en configuración de substrato sobre materiales flexibles de bajo coste. En esta aproximación, las soluciones industriales basadas en láser actualmente disponibles para la interconexión monolítica de dispositivos no son aplica¬bles, y desde hace años se viene investigando en la búsqueda de soluciones apropiadas para el desarrollo de dichos procesos de interconexión de forma que sean transferibles a la industria. En este contexto, esta Tesis propone una aproximación completamente orig¬inal, demostrando la posibilidad de ejecutar una interconexión completa de estos dispositivos irradiando por el lado de la lámina (es decir de forma com¬patible con la opción de configuración de substrato y, valga la redundancia, con el substrato del dispositivo opaco), y con fuentes láser emitiendo en UV. Este resultado, obtenido por primera vez a nivel internacional con este trabajo, aporta un conocimiento revelador del verdadero potencial de estas fuentes en el desarrollo industrial futuro de estas tecnologías. Si bien muy posiblemente la solución industrial final requiera de una solución mixta con el empleo de fuentes en UV y, posiblemente, en otras longitudes de onda, esta Tesis y su planteamiento novedoso aportan un conocimiento de gran valor a la comunidad internacional por la originalidad del planteamiento seguido, los resultados parciales encontrados en su desarrollo (un número importante de los cuales han aparecido en revistas del JCR que recogen en la actualidad un número muy significativo de citas) y porque saca además a la luz, con las consideraciones físicas pertinentes, las limitaciones intrínsecas que el desarrollo de procesos de ablación directa selectiva con láseres UV en parte de los materiales utilizados presenta en el rango temporal de in¬teracción de ns y ps. En este trabajo se han desarrollado y optimizado los tres pasos estándar de interconexión (los habitualmente denominados Pl, P2 y P3 en la industria fotovoltaica) demostrando las ventajas y limitaciones del uso de fuentes en UV tanto con ancho temporal de ns como de ps. En particular destaca, por el éxito en los resultados obtenidos, el estudio de procesos de ablación selectiva de óxidos conductores transparentes (en este trabajo utilizados tanto como contacto frontal así como posterior en los módulos) que ha generado resultados, de excelente acogida científica a nivel internacional, cuya aplicación trasciende el ámbito de las tecnologías de silicio amorfo en lámina delgada. Además en este trabajo de Tesis, en el desarrollo del objetivo citado, se han puesto a punto técnicas de análisis de los procesos láser, basadas en métodos avanzados de caracterización de materiales (como el uso combi¬nado de la espectroscopia dispersiva de rayos X y la microscopía confocal de barrido) que se presentan como auténticos avances en el desarrollo de técnicas específicas de caracterización para el estudio de los procesos con láser de ablación selectiva de materiales en lámina delgada, procesos que no solo tienen impacto en el ámbito de la fotovoltaica, sino también en la microelectrónica, la biotecnología, la microfabricación, etc. Como resultado adicional, parte de los resultados de este trabajo, han sido aplicados exi¬tosamente por el grupo de investigaci´on en la que la autora desarrolla su labor para conseguir desarrollar procesos de enorme inter´es en otras tec-nolog´ıas fotovoltaicas, como las tecnolog´ıas est´andar de silicio amorfo sobre vidrio en configuraci´on de superestrato o el procesado de capas delgadas en tecnolog´ıas convencionales de silicio cristalino. Por u´ltimo decir que este trabajo ha sido posible por una colaboraci´on muy estrecha entre el Centro L´aser de la UPM, en el que la autora de¬sarrolla su labor, y el Grupo de Silicio Depositado del Centro de Inves¬tigaciones Energ´eticas, Medioambientales y Tecnol´ogicas, CIEMAT, que, junto al Grupo de Energ´ıa Fotovoltaica de la Universidad de Barcelona, han preparado la mayor parte de las muestras utilizadas en este estudio. Dichas colaboraciones se han desarrollado en el marco de varios proyectos de investigaci´on aplicada con subvenci´on pu´blica, tales como el proyecto singular estrat´egico PSE-MICROSIL08 (PSE-120000-2006-6), el proyecto INNDISOL (IPT-420000-2010-6), ambos financiados porel Fondo Europeo de Desarrollo Regional FEDER (UE) ”Una manera de hacer Europa y el MICINN, y los proyectos de Plan Nacional AMIC (ENE2010-21384-C04-´ 02) y CLASICO (ENE2007-6772-C04-04), cuya financiaci´on ha permitido en gran parte llevar a t´ermino este trabajo Abstract In the last decade, the laser technology has turned into an indispensable tool in the production of photovoltaic devices, especially of those based on thin film technology. Regardless the current crisis in the sector, the evolution of these technologies in the upcoming years will keep taking advantage of the flexibility and process quality of the laser tool for the accomplishment of the two basic goals that will convert the photovoltaic energy into economically viable: the manufacture cost reduction and the increase in the efficiency of the devices. Amongst the thin film laser technologies, the technology of devices based on amorphous silicon has had a great development in standard systems of superstrate configuration, but its limited efficiency makes its survival de¬pendant on the development of formats in substrate configuration with low cost flexible materials. In this approach, the laser industrial solutions cur¬rently available for the monolithic interconnection are not applicable, and in the last few years the investigations have been focused on the search of appropriate solutions for the development of such interconnection processes in a way that the same are transferable to the industry. In this context, this Thesis proposes a totally original approach, proving the possibility of executing a full interconnection of these devices by means of irradiation from the film side, i.e., compatible with the substrate con¬figuration, and with UV laser sources. This result, obtained for the first time at international level in this work, provides a revealing knowledge of the true potential of these sources in the future industrial development of these technologies. Even though very probably the final industrial solution will require a combination of the use of UV sources along with other wave¬lengths, this Thesis and its novel approach contribute with a high value to the international community because of the originality of the approach, the partial results found throughout its development (out of which, a large number has appeared in JCR journals that currently accumulate a signifi¬cant number of citations) and brings to light, with the pertinent scientific considerations, the intrinsic limitations that the selective direct ablation processes with UV laser present in the temporal range of interaction of ns and ps for part of the materials used in this study. More particularly, the three standard steps of interconnection (usually de¬nominated P1, P2 and P3 in the photovoltaic industry) have been developed and optimized, showing the advantages as well as the limitations of the use of UV sources in both the ns and ps pulse-width ranges. It is highly remark¬able, because of the success in the obtained results, the study of selective ablation processes in transparent conductive oxide (in this work used as a front and back contact), that has generated results, of excellent interna¬tional scientific reception, whose applications go beyond the scope of thin film photovoltaic technologies based on amorphous silicon. Moreover, in this Thesis, with the development of the mentioned goal, differ¬ent techniques of analysis of laser processes have been fine-tuned, basing the same in advanced methods for material characterization (like the combined use of EDX Analysis and Confocal Laser Scanning Microscopy) that can be presented as true breakthroughs in the development of specific techniques for characterization in the study of laser processes of selective ablation of materials in thin film technologies, processes that not only have impact in the photovoltaic field, but also in those of microelectronics, biotechnology, micro-fabrication, etc. As an additional outcome, part of the results of this work has been suc¬cessfully applied, by the investigation group to which the author belongs, to the development of processes of enormous interest within other photo¬voltaic technologies, such as the standard technologies on amorphous silicon over glass in superstrate configuration or the processing of thin layers in conventional technologies using crystalline silicon. Lastly, it is important to mention that this work has been possible thanks to the close cooperation between the Centro L´aser of the UPM, in which the author develops her work, and the Grupo de Silicio Depositado of Centro de Investigaciones Energ´eticas, Medioambientales y Tecnol´ogicas, CIEMAT, which, along with the Grupo de Energ´ıa Fotovoltaica of Univer¬sidad de Barcelona, has prepared the largest part of the samples utilized in this study. Such collaborations have been carried out in the context of several projects of applied investigation with public funding, like Proyecto Singular Estrat´egico PSE-MICROSIL08 (PSE-120000-2006-6), Proyecto IN-NDISOL (IPT-420000-2010-6), both funded by the European Regional De¬velopment Fund (ERDF), ”Una manera de hacer Europa” and MICINN, and the projects of Plan Nacional AMIC (ENE2010-21384-C04-02) and ´ CLASICO (ENE2007-6772-C04-04), whose funds have enabled the devel-opment of large part of this work.

Development of a Uniform Theory of Diffraction for Scattered and Surface Electromagnetic Field Analysis on a Cylinder

Con esta tesis ”Desarrollo de una Teoría Uniforme de la Difracción para el Análisis de los Campos Electromagnéticos Dispersados y Superficiales sobre un Cilindro” hemos iniciado una nueva línea de investigación que trata de responder a la siguiente pregunta: ¿cuál es la impedancia de superficie que describe una estructura de conductor eléctrico perfecto (PEC) convexa recubierta por un material no conductor? Este tipo de estudios tienen interés hoy en día porque ayudan a predecir el campo electromagnético incidente, radiado o que se propaga sobre estructuras metálicas y localmente convexas que se encuentran recubiertas de algún material dieléctrico, o sobre estructuras metálicas con pérdidas, como por ejemplo se necesita en determinadas aplicaciones aeroespaciales, marítimas o automovilísticas. Además, desde un punto de vista teórico, la caracterización de la impedancia de superficie de una estructura PEC recubierta o no por un dieléctrico es una generalización de varias soluciones que tratan ambos tipos de problemas por separado. En esta tesis se desarrolla una teoría uniforme de la difracción (UTD) para analizar el problema canónico del campo electromagnético dispersado y superficial en un cilindro circular eléctricamente grande con una condición de contorno de impedancia (IBC) para frecuencias altas. Construir una solución basada en UTD para este problema canónico es crucial en el desarrollo de un método UTD para el caso más general de una superficie arbitrariamente convexa, mediante el uso del principio de localización de los campos electromagnéticos a altas frecuencias. Esta tesis doctoral se ha llevado a cabo a través de una serie de hitos que se enumeran a continuación, enfatizando las contribuciones a las que ha dado lugar. Inicialmente se realiza una revisión en profundidad del estado del arte de los métodos asintóticos con numerosas referencias. As í, cualquier lector novel puede llegar a conocer la historia de la óptica geométrica (GO) y la teoría geométrica de la difracción (GTD), que dieron lugar al desarrollo de la UTD. Después, se investiga ampliamente la UTD y los trabajos más importantes que pueden encontrarse en la literatura. As í, este capítulo, nos coloca en la posición de afirmar que, hasta donde nosotros conocemos, nadie ha intentado antes llevar a cabo una investigación rigurosa sobre la caracterización de la impedancia de superficie de una estructura PEC recubierta por un material dieléctrico, utilizando para ello la UTD. Primero, se desarrolla una UTD para el problema canónico de la dispersión electromagnética de un cilindro circular eléctricamente grande con una IBC uniforme, cuando es iluminado por una onda plana con incidencia oblicua a frecuencias altas. La solución a este problema canónico se construye a partir de una solución exacta mediante una expansión de autofunciones de propagación radial. Entonces, ésta se convierte en una nueva expansión de autofunciones de propagación circunferencial muy apropiada para cilindros grandes, a través de la transformación de Watson. De esta forma, la expresión del campo se reduce a una integral que se evalúa asintóticamente, para altas frecuencias, de manera uniforme. El resultado se expresa según el trazado de rayos descrito en la UTD. La solución es uniforme porque tiene la importante propiedad de mantenerse continua a lo largo de la región de transición, a ambos lados de la superficie del contorno de sombra. Fuera de la región de transición la solución se reduce al campo incidente y reflejado puramente ópticos en la región iluminada del cilindro, y al campo superficial difractado en la región de sombra. Debido a la IBC el campo dispersado contiene una componente contrapolar a causa de un acoplamiento entre las ondas TEz y TMz (donde z es el eje del cilindro). Esta componente contrapolar desaparece cuando la incidencia es normal al cilindro, y también en la región iluminada cuando la incidencia es oblicua donde el campo se reduce a la solución de GO. La solución UTD presenta una muy buena exactitud cuando se compara numéricamente con una solución de referencia exacta. A continuación, se desarrolla una IBC efectiva para el cálculo del campo electromagnético dispersado en un cilindro circular PEC recubierto por un dieléctrico e iluminado por una onda plana incidiendo oblicuamente. Para ello se derivan dos impedancias de superficie en relación directa con las ondas creeping y de superficie TM y TE que se excitan en un cilindro recubierto por un material no conductor. Las impedancias de superficie TM y TE están acopladas cuando la incidencia es oblicua, y dependen de la geometría del problema y de los números de onda. Además, se ha derivado una impedancia de superficie constante, aunque con diferente valor cuando el observador se encuentra en la zona iluminada o en la zona de sombra. Después, se presenta una solución UTD para el cálculo de la dispersión de una onda plana con incidencia oblicua sobre un cilindro eléctricamente grande y convexo, mediante la generalización del problema canónico correspondiente al cilindro circular. La solución asintótica es uniforme porque se mantiene continua a lo largo de la región de transición, en las inmediaciones del contorno de sombra, y se reduce a la solución de rayos ópticos en la zona iluminada y a la contribución de las ondas de superficie dentro de la zona de sombra, lejos de la región de transición. Cuando se usa cualquier material no conductor se excita una componente contrapolar que tiende a desaparecer cuando la incidencia es normal al cilindro y en la región iluminada. Se discuten ampliamente las limitaciones de las fórmulas para la impedancia de superficie efectiva, y se compara la solución UTD con otras soluciones de referencia, donde se observa una muy buena concordancia. Y en tercer lugar, se presenta una aproximación para una impedancia de superficie efectiva para el cálculo de los campos superficiales en un cilindro circular conductor recubierto por un dieléctrico. Se discuten las principales diferencias que existen entre un cilindro PEC recubierto por un dieléctrico desde un punto de vista riguroso y un cilindro con una IBC. Mientras para un cilindro de impedancia se considera una impedancia de superficie constante o uniforme, para un cilindro conductor recubierto por un dieléctrico se derivan dos impedancias de superficie. Estas impedancias de superficie están asociadas a los modos de ondas creeping TM y TE excitadas en un cilindro, y dependen de la posición y de la orientación del observador y de la fuente. Con esto en mente, se deriva una solución UTD con IBC para los campos superficiales teniendo en cuenta las dependencias de la impedancia de superficie. La expansión asintótica se realiza, mediante la transformación de Watson, sobre la representación en serie de las funciones de Green correspondientes, evitando as í calcular las derivadas de orden superior de las integrales de tipo Fock, y dando lugar a una solución rápida y precisa. En los ejemplos numéricos realizados se observa una muy buena precisión cuando el cilindro y la separación entre el observador y la fuente son grandes. Esta solución, junto con el método de los momentos (MoM), se puede aplicar para el cálculo eficiente del acoplamiento mutuo de grandes arrays conformados de antenas de parches. Los métodos propuestos basados en UTD para el cálculo del campo electromagnético dispersado y superficial sobre un cilindro PEC recubierto de dieléctrico con una IBC efectiva suponen un primer paso hacia la generalización de una solución UTD para superficies metálicas convexas arbitrarias cubiertas por un material no conductor e iluminadas por una fuente electromagnética arbitraria. ABSTRACT With this thesis ”Development of a Uniform Theory of Diffraction for Scattered and Surface Electromagnetic Field Analysis on a Cylinder” we have initiated a line of investigation whose goal is to answer the following question: what is the surface impedance which describes a perfect electric conductor (PEC) convex structure covered by a material coating? These studies are of current and future interest for predicting the electromagnetic (EM) fields incident, radiating or propagating on locally smooth convex parts of highly metallic structures with a material coating, or by a lossy metallic surfaces, as for example in aerospace, maritime and automotive applications. Moreover, from a theoretical point of view, the surface impedance characterization of PEC surfaces with or without a material coating represents a generalization of independent solutions for both type of problems. A uniform geometrical theory of diffraction (UTD) is developed in this thesis for analyzing the canonical problem of EM scattered and surface field by an electrically large circular cylinder with an impedance boundary condition (IBC) in the high frequency regime, by means of a surface impedance characterization. The construction of a UTD solution for this canonical problem is crucial for the development of the corresponding UTD solution for the more general case of an arbitrary smooth convex surface, via the principle of the localization of high frequency EM fields. The development of the present doctoral thesis has been carried out through a series of landmarks that are enumerated as follows, emphasizing the main contributions that this work has given rise to. Initially, a profound revision is made in the state of art of asymptotic methods where numerous references are given. Thus, any reader may know the history of geometrical optics (GO) and geometrical theory of diffraction (GTD), which led to the development of UTD. Then, the UTD is deeply investigated and the main studies which are found in the literature are shown. This chapter situates us in the position to state that, as far as we know, nobody has attempted before to perform a rigorous research about the surface impedance characterization for material-coated PEC convex structures via UTD. First, a UTD solution is developed for the canonical problem of the EM scattering by an electrically large circular cylinder with a uniform IBC, when it is illuminated by an obliquely incident high frequency plane wave. A solution to this canonical problem is first constructed in terms of an exact formulation involving a radially propagating eigenfunction expansion. The latter is converted into a circumferentially propagating eigenfunction expansion suited for large cylinders, via the Watson transformation, which is expressed as an integral that is subsequently evaluated asymptotically, for high frequencies, in a uniform manner. The resulting solution is then expressed in the desired UTD ray form. This solution is uniform in the sense that it has the important property that it remains continuous across the transition region on either side of the surface shadow boundary. Outside the shadow boundary transition region it recovers the purely ray optical incident and reflected ray fields on the deep lit side of the shadow boundary and to the modal surface diffracted ray fields on the deep shadow side. The scattered field is seen to have a cross-polarized component due to the coupling between the TEz and TMz waves (where z is the cylinder axis) resulting from the IBC. Such cross-polarization vanishes for normal incidence on the cylinder, and also in the deep lit region for oblique incidence where it properly reduces to the GO or ray optical solution. This UTD solution is shown to be very accurate by a numerical comparison with an exact reference solution. Then, an effective IBC is developed for the EM scattered field on a coated PEC circular cylinder illuminated by an obliquely incident plane wave. Two surface impedances are derived in a direct relation with the TM and TE surface and creeping wave modes excited on a coated cylinder. The TM and TE surface impedances are coupled at oblique incidence, and depend on the geometry of the problem and the wave numbers. Nevertheless, a constant surface impedance is found, although with a different value when the observation point lays in the lit or in the shadow region. Then, a UTD solution for the scattering of an obliquely incident plane wave on an electrically large smooth convex coated PEC cylinder is introduced, via a generalization of the canonical circular cylinder problem. The asymptotic solution is uniform because it remains continuous across the transition region, in the vicinity of the shadow boundary, and it recovers the ray optical solution in the deep lit region and the creeping wave formulation within the deep shadow region. When a coating is present a cross-polar field term is excited, which vanishes at normal incidence and in the deep lit region. The limitations of the effective surface impedance formulas are discussed, and the UTD solution is compared with some reference solutions where a very good agreement is met. And in third place, an effective surface impedance approach is introduced for determining surface fields on an electrically large coated metallic circular cylinder. Differences in analysis of rigorouslytreated coated metallic cylinders and cylinders with an IBC are discussed. While for the impedance cylinder case a single constant or uniform surface impedance is considered, for the coated metallic cylinder case two surface impedances are derived. These are associated with the TM and TE creeping wave modes excited on a cylinder and depend on observation and source positions and orientations. With this in mind, a UTD based method with IBC is derived for the surface fields by taking into account the surface impedance variation. The asymptotic expansion is performed, via the Watson transformation, over the appropriate series representation of the Green’s functions, thus avoiding higher-order derivatives of Fock-type integrals, and yielding a fast and an accurate solution. Numerical examples reveal a very good accuracy for large cylinders when the separation between the observation and the source point is large. Thus, this solution could be efficiently applied in mutual coupling analysis, along with the method of moments (MoM), of large conformal microstrip array antennas. The proposed UTD methods for scattered and surface EM field analysis on a coated PEC cylinder with an effective IBC are considered the first steps toward the generalization of a UTD solution for large arbitrarily convex smooth metallic surfaces covered by a material coating and illuminated by an arbitrary EM source.