Spacecraft launch depressurization loads

The pressure variation inside the launch vehicle fairing during climb through the atmosphere induces structural loads on the walls of closed-type spacecrafts or equipment boxes. If the evacuation of the air is not fast enough, excessive pressure loading can result in damage of elements exposed to the rising pressure jump, which depends mainly on the geometry of venting holes, the effective volume of air to be evacuated, and the characteristic time of pressure variation under the fairing. A theoretical study of the reservoir discharge forced by the fairing time-dependent pressure variation is presented. The basic mathematical model developed can yield both a numerical solution for the pressure jump and an asymptotic solution for the most relevant case, the small-prcssurc-jump limit, showing the dependence on a single nondimensional parameter: the ratio of the reservoir discharge to the fairing pressure profile characteristic times. The asymptotic solution validity range upper limit, obtained by comparison with the numerical solution, is determined by the starting of choked operation. Very high sensitivity of the maximum pressure jump to the ratio of characteristic times has been observed. Another relevant finding is that the pressure profiles for different launchers can be considered similar when rewritten in appropriate form and only their characteristic times are required for the analysis. The simple expressions of the asymptotic solution are a useful tool for preliminarily sizing the reservoir discharge geometry and estimating depressurization loads

Rapid sizing tool for a low cost university microsatellite structure subsystem

In recent decays university class small satellites are creating many opportunities for space research and professional trainings while at the same time responding to constrained budgets. In this work the main focus is on developing a simple and rapid structural sizing tool considering the main objectives of a low cost university class microsatellite project. In satellite projects, structure subsystem is one of the influential subsystems as a driver of the cost and acceptance of the final design. At the first steps of such projects there is no confirmed data regarding the launch vehicle or even in some cases there is no data for the satellite payload. Due to these facts, developing simple sizing tools at conceptual design phase for obtaining an over view of the effect of different variables is useful before entering complex calculations in detailed design phases. In this study, after developing a simple analytical model of satellite structure subsystem, a design space is evaluated with practical boundaries considering mass and dimensions constraints of such projects. The results are useful to give initial insight to establish the system level structural sizing

Thermal behaviour of Sunrise, a balloon-borne solar Telescope

Sunrise is a solar telescope, successfully flown in June 2009 with a long duration balloon from the Swedish Space Corporation Esrange launch site. The design of the thermal control of SUNRISE was quite critical because of the sensitivity to temperature of the optomechanical devices and the electronics. These problems got more complicated due the size and high power dissipation of the system. A detailed thermal mathematical model of SUNRISE was set up to predict temperatures. In this communication the thermal behaviour of SUNRISE during flight is presented. Flight temperatures of some devices are presented and analysed. The measured data have been compared with the predictions given by the thermal mathematical models. The main discrepancies between flight data and the temperatures predicted by the models have been identified. This allows thermal engineers to improve the knowledge of the thermal behaviour of the system for future missions.

Criterios de optimización de los incentivos en contratos de concesión ligados a indicadores de calidad de servicio para firmes bituminosos

Actualmente se está empezando a consolidar una nueva forma de gestionar la conservación y mantenimiento de la red viaria de las Administraciones Públicas, basándose en contratos de colaboración público-privadas (PPP). Las motivaciones que están provocando este movimiento son de diversa índole. Por un lado, en el seno de la Unión Europea, existen serias restricciones presupuestarias debido al alto endeudamiento del sector público, lo que está llevando a buscar la forma óptima de disminuir el endeudamiento público, sin dejar de prestar servicios a la sociedad como la conservación y mantenimiento de las redes viarias. Por esta vertiente, se trata de convertir contratos convencionales de conservación viaria a esquemas de colaboración público-privada, donde se transferiría al sector privado el riesgo de disponibilidad de la vía mediante el uso de indicadores de calidad y servicio. Con esta transferencia de riesgo, junto con la transferencia del riesgo de demanda/construcción, no consolidaría la deuda de la sociedad de propósito específico constituida para la gestión del contrato de colaboración público-privada dentro de las cuentas públicas, con lo que se conseguiría no aumentar el déficit público, permitiendo continuar ofreciendo el servicio demandado por la sociedad. Por otro lado, la segunda motivación del desarrollo de este tipo de contratos, no tan economicista como la anterior y más enfocada a la gestión, se trata de utilizar los contratos de gestión basados en el uso de indicadores de calidad de servicio para mejorar las prestaciones de la red viaria competencia de una Administración. Con el uso de estos indicadores, el gestor tiene una herramienta muy útil para controlar la actividad del sector privado y asegurar que se ofrece un buen servicio. En la presente tesis, la investigación se ha centrado más en la vertiente de los indicadores de calidad relacionados con la gestión eficiente de las vías objeto de conservación y mantenimiento mediante el empleo de contratos de gestión privada que utilicen este tipo de herramientas de control, monitorización y gestión. En una primera parte, la presente tesis estudia el estado de la red de carreteras, referido principalmente a España, comparando su estado con el resto de redes de carreteras de Europa, detectando las principales carencias de la misma, sobre todo en cuanto a la gestión y conservación de firmes. En un segundo bloque, la tesis analiza el estado del arte de los nuevos procedimientos de gestión de la conservación y mantenimiento basados en indicadores de calidad del servicio en el mundo, destacándose que se trata de un tema relativamente reciente, con gran interés para el sector de la gestión y financiación de infraestructuras viarias. Al ser tan novedoso, por la falta de experiencias previas, las distintas Administración, tanto propias como foráneas, han pecado de un exceso de celo a la hora de establecer los umbrales sobre los que giran los distintos indicadores de calidad de servicio que permiten controlar la gestión de la conservación y mantenimiento de la vía. Partiendo de la labor de análisis descrita, la tesis realiza una investigación más detallada de los indicadores de calidad de servicio correspondientes a firmes bituminosos, debido a que estos indicadores son los más delicados y decisivos a la hora de realizar una correcta gestión de la vía a largo plazo. Dentro de los indicadores de firmes bituminosos, se ha realizado un modelo específico de evolución de comportamiento a lo largo del tiempo de la regularidad superficial, parámetro básico para numerosas Administraciones y organismos investigadores para poder conocer la evolución de un firme a lo largo del tiempo. A esta metodología se le ha dado el nombre de Modelo JRB para evaluar la racionalidad económica de indicadores de calidad asociados a parámetros de firmes. El modelo propuesto básicamente evalúa el valor óptimo desde la perspectiva económica que ha de tener el parámetro técnico que defina alguna propiedad del firme, aplicado a la definición de los indicadores de calidad de servicio. Esta visión del valor umbral del indicador deja a un lado consideraciones de equidad o de cualquier otra índole, basándose más en una visión económica. La metodología del Modelo JRB se puede aplicar a cualquier indicador de calidad relacionado con firmes, ya que lo que se obtiene es el valor óptimo económico que debería tener el umbral del indicador de calidad. El Modelo JRB consta de varias fases. En las primeras etapas el Modelo realiza el cálculo de los costes totales de transporte utilizando como herramienta el software HDM-IV desarrollado por el Banco Mundial. En etapas posteriores, el Modelo realiza análisis de sensibilidad para distintas propuestas de sección de firme, intensidades de tráfico y restricciones al parámetro técnico que define el indicador de calidad de servicio. Como ejercicio práctico de cara a contrastar la metodología del Modelo JRB se ha realizado un Caso de Estudio. Se ha tomado un tramo teórico, con características similares a la red de carreteras española, y con una flota vehicular similar a la española, donde se ha elegido como indicador de calidad la regularidad superficial (IRI). Con las sensibilidades realizadas con el Modelo JRB, se ha determinado el rango de valores que debería tener un indicador de calidad basado en el IRI para que dichos valores fueran óptimos desde la perspectiva económica Nowadays is becoming a new way to manage O&M (operation and maintenance) in public road networks, based on PPP contracts (public-private partnership). There are several issues which are driving this trend. On the one hand, EU (European Union) has serious budgetary constraints due to the high public sector borrowing. EU politicians are looking for the best way to reduce public debt, keeping services to society such as O&M of road networks. For this aspect, conventional O&M contracts are switching to PPP scenarios, where availability risk would be transfer to private sector using PI (performance indicators), along with demand risk transfer With this risk transference, along with the transfer of demand/construction risk, SPV (specific purpose vehicle) debt doesn’t consolidate in public accounts, so deficit wouldn’t increase, allowing the continuation of services demanded by society. On the other hand, the second motivation for developing this kind of contracts, not so economist as above and more focused to management, it is about using O&M contracts based on the use of PI to improve road network maintenance. Using these indicators, manager has a very useful tool to monitor private sector activity and ensure that it is provided a good service. In this thesis, the research has been focused on PI quality aspect, related with efficient management of PPP contracts for roads, which use these tools for control, monitoring and management. In the first part, this thesis examines the state of road network, based mainly in Spain, comparing with other road networks in Europe, identifying the main gaps in it, especially with regard to the management and maintenance of pavements. In a second block, the thesis analyzes the state of art of new O&M contracts based on PI in the world, emphasizing that they are relatively recent. These kinds of contracts have a great interest in road management and financing sector. Administrations all around the world have launch tenders with very exigent PI thresholds due to several factors: this knowledge is a new area, the lack of previous experiences and the variety of Administrations which have bid these contracts. Building on the described analysis, thesis develops a more detailed research about PI for bituminous pavements, because these PI are the most delicate and decisive in making a proper long term road management. Among bituminous pavements PI, IRI (International Roughness Index) has been analyzed with more detail and has been developed a specific model of behaviour evolution over time for evenness (IRI), basic parameter for many administrations and research departments in order to know the evolution of a pavement over time. This methodology has been given the name of JRB Model to evaluate the economic rationality of performance indicators associated with pavements parameters. The proposed model basically evaluates the optimal value from an economic perspective it must have the technical parameter which defines some pavement characteristic applied to the definition of performance indicators. This point of view of indicator value threshold sets aside justice considerations or otherwise, based more on an economic perspective. JRB Model methodology can be applied to any performance indicator associated to pavements, because what you get is the economic optimum threshold should have the performance indicator. JRB Model consists of several phases. In the early stages, the Model calculates transport total cost using HDM-IV software, developed by the World Bank, as a tool. In later stages, the Model performs sensitivity analyzes for different pavement section, AADT and restrictions to the technical parameter which defines the performance indicator. As a practical exercise to test JRB Model methodology, it has done a Case Study. It has taken a theoretical section, with similar characteristics to Spanish road network, and a vehicles fleet similar to Spanish. Evenness (IRI) was chosen as a performance indicator. JRB Model calculated some sensitivities, which were useful to determined thresholds range for pavement performance indicators based on IRI to be optimal from an economic perspective.

Aplicaciones de interés forestal de las imágenes obtenidas con el sensor Multi-angle Imaging SpectroRadiometer (MISR)

Las aplicaciones de la teledetección al seguimiento de lo que ocurre en la superficie terrestre se han ido multiplicando y afinando con el lanzamiento de nuevos sensores por parte de las diferentes agencias espaciales. La necesidad de tener información actualizada cada poco tiempo y espacialmente homogénea, ha provocado el desarrollo de nuevos programas como el Earth Observing System (EOS) de la National Aeronautics and Space Administration (NASA). Uno de los sensores que incorpora el buque insignia de ese programa, el satélite TERRA, es el Multi-angle Imaging SpectroRadiometer (MISR), diseñado para capturar información multiangular de la superficie terrestre. Ya desde los años 1970, se conocía que la reflectancia de las diversas ocupaciones y usos del suelo variaba en función del ángulo de observación y de iluminación, es decir, que eran anisotrópicas. Tal variación estaba además relacionada con la estructura tridimensional de tales ocupaciones, por lo que se podía aprovechar tal relación para obtener información de esa estructura, más allá de la que pudiera proporcionar la información meramente espectral. El sensor MISR incorpora 9 cámaras a diferentes ángulos para capturar 9 imágenes casi simultáneas del mismo punto, lo que permite estimar con relativa fiabilidad la respuesta anisotrópica de la superficie terrestre. Varios trabajos han demostrado que se pueden estimar variables relacionadas con la estructura de la vegetación con la información que proporciona MISR. En esta Tesis se ha realizado una primera aplicación a la Península Ibérica, para comprobar su utilidad a la hora de estimar variables de interés forestal. En un primer paso se ha analizado la variabilidad temporal que se produce en los datos, debido a los cambios en la geometría de captación, es decir, debido a la posición relativa de sensores y fuente de iluminación, que en este caso es el Sol. Se ha comprobado cómo la anisotropía es mayor desde finales de otoño hasta principios de primavera debido a que la posición del Sol es más cercana al plano de los sensores. También se ha comprobado que los valores máximo y mínimo se van desplazando temporalmente entre el centro y el extremo angular. En la caracterización multiangular de ocupaciones del suelo de CORINE Land Cover que se ha realizado, se puede observar cómo la forma predominante en las imágenes con el Sol más alto es convexa con un máximo en la cámara más cercana a la fuente de iluminación. Sin embargo, cuando el Sol se encuentra mucho más bajo, ese máximo es muy externo. Por otra parte, los datos obtenidos en verano son mucho más variables para cada ocupación que los de noviembre, posiblemente debido al aumento proporcional de las zonas en sombra. Para comprobar si la información multiangular tiene algún efecto en la obtención de imágenes clasificadas según ocupación y usos del suelo, se han realizado una serie de clasificaciones variando la información utilizada, desde sólo multiespectral, a multiangular y multiespectral. Los resultados muestran que, mientras para las clasificaciones más genéricas la información multiangular proporciona los peores resultados, a medida que se amplían el número de clases a obtener tal información mejora a lo obtenido únicamente con información multiespectral. Por otra parte, se ha realizado una estimación de variables cuantitativas como la fracción de cabida cubierta (Fcc) y la altura de la vegetación a partir de información proporcionada por MISR a diferentes resoluciones. En el valle de Alcudia (Ciudad Real) se ha estimado la fracción de cabida cubierta del arbolado para un píxel de 275 m utilizando redes neuronales. Los resultados muestran que utilizar información multiespectral y multiangular puede mejorar casi un 20% las estimaciones realizadas sólo con datos multiespectrales. Además, las relaciones obtenidas llegan al 0,7 de R con errores inferiores a un 10% en Fcc, siendo éstos mucho mejores que los obtenidos con el producto elaborado a partir de datos multiespectrales del sensor Moderate Resolution Imaging Spectroradiometer (MODIS), también a bordo de Terra, para la misma variable. Por último, se ha estimado la fracción de cabida cubierta y la altura efectiva de la vegetación para 700.000 ha de la provincia de Murcia, con una resolución de 1.100 m. Los resultados muestran la relación existente entre los datos espectrales y los multiangulares, obteniéndose coeficientes de Spearman del orden de 0,8 en el caso de la fracción de cabida cubierta de la vegetación, y de 0,4 en el caso de la altura efectiva. Las estimaciones de ambas variables con redes neuronales y diversas combinaciones de datos, arrojan resultados con R superiores a 0,85 para el caso del grado de cubierta vegetal, y 0,6 para la altura efectiva. Los parámetros multiangulares proporcionados en los productos elaborados con MISR a 1.100 m, no obtienen buenos resultados por sí mismos pero producen cierta mejora al incorporarlos a la información espectral. Los errores cuadráticos medios obtenidos son inferiores a 0,016 para la Fcc de la vegetación en tanto por uno, y 0,7 m para la altura efectiva de la misma. Regresiones geográficamente ponderadas muestran además que localmente se pueden obtener mejores resultados aún mejores, especialmente cuando hay una mayor variabilidad espacial de las variables estimadas. En resumen, la utilización de los datos proporcionados por MISR ofrece una prometedora vía de mejora de resultados en la media-baja resolución, tanto para la clasificación de imágenes como para la obtención de variables cuantitativas de la estructura de la vegetación. ABSTRACT Applications of remote sensing for monitoring what is happening on the land surface have been multiplied and refined with the launch of new sensors by different Space Agencies. The need of having up to date and spatially homogeneous data, has led to the development of new programs such as the Earth Observing System (EOS) of the National Aeronautics and Space Administration (NASA). One of the sensors incorporating the flagship of that program, the TERRA satellite, is Multi-angle Imaging Spectroradiometer (MISR), designed to capture the multi-angle information of the Earth's surface. Since the 1970s, it was known that the reflectance of various land covers and land uses varied depending on the viewing and ilumination angles, so they are anisotropic. Such variation was also related to the three dimensional structure of such covers, so that one could take advantage of such a relationship to obtain information from that structure, beyond which spectral information could provide. The MISR sensor incorporates 9 cameras at different angles to capture 9 almost simultaneous images of the same point, allowing relatively reliable estimates of the anisotropic response of the Earth's surface. Several studies have shown that we can estimate variables related to the vegetation structure with the information provided by this sensor, so this thesis has made an initial application to the Iberian Peninsula, to check their usefulness in estimating forest variables of interest. In a first step we analyzed the temporal variability that occurs in the data, due to the changes in the acquisition geometry, i.e. the relative position of sensor and light source, which in this case is the Sun. It has been found that the anisotropy is greater from late fall through early spring due to the Sun's position closer to the plane of the sensors. It was also found that the maximum and minimum values are displaced temporarily between the center and the ends. In characterizing CORINE Land Covers that has been done, one could see how the predominant form in the images with the highest sun is convex with a maximum in the camera closer to the light source. However, when the sun is much lower, the maximum is external. Moreover, the data obtained for each land cover are much more variable in summer that in November, possibly due to the proportional increase in shadow areas. To check whether the information has any effect on multi-angle imaging classification of land cover and land use, a series of classifications have been produced changing the data used, from only multispectrally, to multi-angle and multispectral. The results show that while for the most generic classifications multi-angle information is the worst, as there are extended the number of classes to obtain such information it improves the results. On the other hand, an estimate was made of quantitative variables such as canopy cover and vegetation height using information provided by MISR at different resolutions. In the valley of Alcudia (Ciudad Real), we estimated the canopy cover of trees for a pixel of 275 m by using neural networks. The results showed that using multispectral and multiangle information can improve by almost 20% the estimates that only used multispectral data. Furthermore, the relationships obtained reached an R coefficient of 0.7 with errors below 10% in canopy cover, which is much better result than the one obtained using data from the Moderate Resolution Imaging Spectroradiometer (MODIS), also onboard Terra, for the same variable. Finally we estimated the canopy cover and the effective height of the vegetation for 700,000 hectares in the province of Murcia, with a spatial resolution of 1,100 m. The results show a relationship between the spectral and the multi-angle data, and provide estimates of the canopy cover with a Spearman’s coefficient of 0.8 in the case of the vegetation canopy cover, and 0.4 in the case of the effective height. The estimates of both variables using neural networks and various combinations of data, yield results with an R coefficient greater than 0.85 for the case of the canopy cover, and 0.6 for the effective height. Multi-angle parameters provided in the products made from MISR at 1,100 m pixel size, did not produce good results from themselves but improved the results when included to the spectral information. The mean square errors were less than 0.016 for the canopy cover, and 0.7 m for the effective height. Geographically weighted regressions also showed that locally we can have even better results, especially when there is high spatial variability of estimated variables. In summary, the use of the data provided by MISR offers a promising way of improving remote sensing performance in the low-medium spatial resolution, both for image classification and for the estimation of quantitative variables of the vegetation structure.

Aplicación de documentos de identificación electrónica a un esquema de voto telemático a escala paneuropea, seguro, auditable y verificable.

En este trabajo de tesis se propone un esquema de votación telemática, de carácter paneuropeo y transnacional, que es capaz de satisfacer las más altas exigencias en materia de seguridad. Este enfoque transnacional supone una importante novedad que obliga a identificar a los ciudadanos más allá de las fronteras de su país, exigencia que se traduce en la necesidad de que todos los ciudadanos europeos dispongan de una identidad digital y en que ésta sea reconocida más allá de las fronteras de su país de origen. Bajo estas premisas, la propuesta recogida en esta tesis se aborda desde dos vertientes complementarias: por una parte, el diseño de un esquema de votación capaz de conquistar la confianza de gobiernos y ciudadanos europeos y, por otra, la búsqueda de una respuesta al problema de interoperabilidad de Sistemas de Gestión de Identidad (IDMs), en consonancia con los trabajos que actualmente realiza la UE para la integración de los servicios proporcionados por las Administraciones Públicas de los distintos países europeos. El punto de partida de este trabajo ha sido la identificación de los requisitos que determinan el adecuado funcionamiento de un sistema de votación telemática para, a partir de ellos,proponer un conjunto de elementos y criterios que permitan, por una parte, establecer comparaciones entre distintos sistemas telemáticos de votación y, por otra, evaluar la idoneidad del sistema propuesto. A continuación se han tomado las más recientes y significativas experiencias de votación telemática llevadas a cabo por diferentes países en la automatización de sus procesos electorales, analizándolas en profundidad para demostrar que, incluso en los sistemas más recientes, todavía subsisten importantes deficiencias relativas a la seguridad. Asimismo, se ha constatado que un sector importante de la población se muestra receloso y, a menudo, cuestiona la validez de los resultados publicados. Por tanto, un sistema que aspire a ganarse la confianza de ciudadanos y gobernantes no sólo debe operar correctamente, trasladando los procesos tradicionales de votación al contexto telemático, sino que debe proporcionar mecanismos adicionales que permitan superar los temores que inspira el nuevo sistema de votación. Conforme a este principio, el enfoque de esta tesis, se orienta, en primer lugar, hacia la creación de pruebas irrefutables, entendibles y auditables a lo largo de todo el proceso de votación, que permitan demostrar con certeza y ante todos los actores implicados en el proceso (gobierno, partidos políticos, votantes, Mesa Electoral, interventores, Junta Electoral,jueces, etc.) que los resultados publicados son fidedignos y que no se han violado los principios de anonimato y de “una persona, un voto”. Bajo este planteamiento, la solución recogida en esta tesis no sólo prevé mecanismos para minimizar el riesgo de compra de votos, sino que además incorpora mecanismos de seguridad robustos que permitirán no sólo detectar posibles intentos de manipulación del sistema, sino también identificar cuál ha sido el agente responsable. De forma adicional, esta tesis va más allá y traslada el escenario de votación a un ámbito paneuropeo donde aparecen nuevos problemas. En efecto, en la actualidad uno de los principales retos a los que se enfrentan las votaciones de carácter transnacional es sin duda la falta de procedimientos rigurosos y dinámicos para la actualización sincronizada de los censos de votantes de los distintos países que evite la presencia de errores que redunden en la incapacidad de controlar que una persona emita más de un voto, o que se vea impedido del todo a ejercer su derecho. Este reconocimiento de la identidad transnacional requiere la interoperabilidad entre los IDMs de los distintos países europeos. Para dar solución a este problema, esta tesis se apoya en las propuestas emergentes en el seno de la UE, que previsiblemente se consolidarán en los próximos años, tanto en materia de identidad digital (con la puesta en marcha de la Tarjeta de Ciudadano Europeo) como con el despliegue de una infraestructura de gestión de identidad que haga posible la interoperabilidad de los IDMs de los distintos estados miembros. A partir de ellas, en esta tesis se propone una infraestructura telemática que facilita la interoperabilidad de los sistemas de gestión de los censos de los distintos estados europeos en los que se lleve a cabo conjuntamente la votación. El resultado es un sistema versátil, seguro, totalmente robusto, fiable y auditable que puede ser aplicado en elecciones paneuropeas y que contempla la actualización dinámica del censo como una parte crítica del proceso de votación. ABSTRACT: This Ph. D. dissertation proposes a pan‐European and transnational system of telematic voting that is capable of meeting the strictest security standards. This transnational approach is a significant innovation that entails identifying citizens beyond the borders of their own country,thus requiring that all European citizens must have a digital identity that is recognized beyond the borders of their country of origin. Based on these premises, the proposal in this thesis is analyzed in two mutually‐reinforcing ways: first, a voting system is designed that is capable of winning the confidence of European governments and citizens and, second, a solution is conceived for the problem of interoperability of Identity Management Systems (IDMs) that is consistent with work being carried out by the EU to integrate the services provided by the public administrations of different European countries. The starting point of this paper is to identify the requirements for the adequate functioning of a telematic voting system and then to propose a set of elements and criteria that will allow for making comparisons between different such telematic voting systems for the purpose of evaluating the suitability of the proposed system. Then, this thesis provides an in‐depth analysis of most recent significant experiences in telematic voting carried out by different countries with the aim of automating electoral processes, and shows that even the most recent systems have significant shortcomings in the realm of security. Further, a significant portion of the population has shown itself to be wary,and they often question the validity of the published results. Therefore, a system that aspires to win the trust of citizens and leaders must not only operate correctly by transferring traditional voting processes into a telematic environment, but must also provide additional mechanisms that can overcome the fears aroused by the new voting system. Hence, this thesis focuses, first, on creating irrefutable, comprehensible and auditable proof throughout the voting process that can demonstrate to all actors in the process – the government, political parties, voters, polling station workers, electoral officials, judges, etc. ‐that the published results are accurate and that the principles of anonymity and one person,one vote, have not been violated. Accordingly, the solution in this thesis includes mechanisms to minimize the risk of vote buying, in addition to robust security mechanisms that can not only detect possible attempts to manipulate the system, but also identify the responsible party. Additionally, this thesis goes one step further and moves the voting scenario to a pan‐European scale, in which new problems appear. Indeed, one of the major challenges at present for transnational voting processes is the lack of rigorous and dynamic procedures for synchronized updating of different countries’ voter rolls, free from errors that may make the system unable to keep an individual from either casting more than one vote, or from losing the effective exercise of the right to vote. This recognition of transnational identity requires interoperability between the IDMs of different European countries. To solve the problem, this thesis relies on proposals emerging within the EU that are expected to take shape in the coming years, both in digital identity – with the launch of the European Citizen Card – and in the deployment of an identity management infrastructure that will enable interoperability of the IDMs of different member states. Based on these, the thesis proposes a telematic infrastructure that will achieve interoperability of the census management systems of European states in which voting processes are jointly carried out. The result is a versatile, secure, totally robust, reliable and auditable system that can be applied in pan‐European election, and that includes dynamic updating of the voter rolls as a critical part of the voting process.

Multiobjective optimization applied to structural sizing of low cost university-class microsatellite projects

In recent years, there has been continuing interest in the participation of university research groups in space technology studies by means of their own microsatellites. The involvement in such projects has some inherent challenges, such as limited budget and facilities. Also, due to the fact that the main objective of these projects is for educational purposes, usually there are uncertainties regarding their in orbit mission and scientific payloads at the early phases of the project. On the other hand, there are predetermined limitations for their mass and volume budgets owing to the fact that most of them are launched as an auxiliary payload in which the launch cost is reduced considerably. The satellite structure subsystem is the one which is most affected by the launcher constraints. This can affect different aspects, including dimensions, strength and frequency requirements. In this paper, the main focus is on developing a structural design sizing tool containing not only the primary structures properties as variables but also the system level variables such as payload mass budget and satellite total mass and dimensions. This approach enables the design team to obtain better insight into the design in an extended design envelope. The structural design sizing tool is based on analytical structural design formulas and appropriate assumptions including both static and dynamic models of the satellite. Finally, a Genetic Algorithm (GA) multiobjective optimization is applied to the design space. The result is a Pareto-optimal based on two objectives, minimum satellite total mass and maximum payload mass budget, which gives a useful insight to the design team at the early phases of the design.

Adaptive liquid-crystal phase-only passive devices

This PhD work is focused on liquid crystal based tunable phase devices with special emphasis on their design and manufacturing. In the course of the work a number of new manufacturing technologies have been implemented in the UPM clean room facilities, leading to an important improvement in the range of devices being manufactured in the laboratory. Furthermore, a number of novel phase devices have been developed, all of them including novel electrodes, and/or alignment layers. The most important manufacturing progress has been the introduction of reactive ion etching as a tool for achieving high resolution photolithography on indium-tin-oxide (ITO) coated glass and quartz substrates. Another important manufacturing result is the successful elaboration of a binding protocol of anisotropic conduction adhesives. These have been employed in high density interconnections between ITO-glass and flexible printed circuits. Regarding material characterization, the comparative study of nonstoichiometric silicon oxide (SiOx) and silica (SiO2) inorganic alignment layers, as well as the relationship between surface layer deposition, layer morphology and liquid crystal electrooptical response must be highlighted, together with the characterization of the degradation of liquid crystal devices in simulated space mission environment. A wide variety of phase devices have been developed, with special emphasis on beam steerers. One of these was developed within the framework of an ESA project, and consisted of a high density reconfigurable 1D blaze grating, with a spatial separation of the controlling microelectronics and the active, radiation exposed, area. The developed devices confirmed the assumption that liquid crystal devices with such a separation of components, are radiation hard, and can be designed to be both vibration and temperature sturdy. In parallel to the above, an evenly variable analog beam steering device was designed, manufactured and characterized, providing a narrow cone diffraction free beam steering. This steering device is characterized by a very limited number of electrodes necessary for the redirection of a light beam. As few as 4 different voltage levels were needed in order to redirect a light beam. Finally at the Wojskowa Akademia Techniczna (Military University of Technology) in Warsaw, Poland, a wedged analog tunable beam steering device was designed, manufactured and characterized. This beam steerer, like the former one, was designed to resist the harsh conditions both in space and in the context of the shuttle launch. Apart from the beam steering devices, reconfigurable vortices and modal lens devices have been manufactured and characterized. In summary, during this work a large number of liquid crystal devices and liquid crystal device manufacturing technologies have been developed. Besides their relevance in scientific publications and technical achievements, most of these new devices have demonstrated their usefulness in the actual work of the research group where this PhD has been completed. El presente trabajo de Tesis se ha centrado en el diseño, fabricación y caracterización de nuevos dispositivos de fase basados en cristal líquido. Actualmente se están desarrollando dispositivos basados en cristal líquido para aplicaciones diferentes a su uso habitual como displays. Poseen la ventaja de que los dispositivos pueden ser controlados por bajas tensiones y no necesitan elementos mecánicos para su funcionamiento. La fabricación de todos los dispositivos del presente trabajo se ha realizado en la cámara limpia del grupo. La cámara limpia ha sido diseñada por el grupo de investigación, es de dimensiones reducidas pero muy versátil. Está dividida en distintas áreas de trabajo dependiendo del tipo de proceso que se lleva a cabo. La cámara limpia está completamente cubierta de un material libre de polvo. Todas las entradas de suministro de gas y agua están selladas. El aire filtrado es constantemente bombeado dentro de la zona limpia, a fin de crear una sobrepresión evitando así la entrada de aire sin filtrar. Las personas que trabajan en esta zona siempre deben de estar protegidas con un traje especial. Se utilizan trajes especiales que constan de: mono, máscara, guantes de látex, gorro, patucos y gafas de protección UV, cuando sea necesario. Para introducir material dentro de la cámara limpia se debe limpiar con alcohol y paños especiales y posteriormente secarlos con nitrógeno a presión. La fabricación debe seguir estrictamente unos pasos determinados, que pueden cambiar dependiendo de los requerimientos de cada dispositivo. Por ello, la fabricación de dispositivos requiere la formulación de varios protocolos de fabricación. Estos protocolos deben ser estrictamente respetados a fin de obtener repetitividad en los experimentos, lo que lleva siempre asociado un proceso de fabricación fiable. Una célula de cristal líquido está compuesta (de forma general) por dos vidrios ensamblados (sándwich) y colocados a una distancia determinada. Los vidrios se han sometido a una serie de procesos para acondicionar las superficies internas. La célula se llena con cristal líquido. De forma resumida, el proceso de fabricación general es el siguiente: inicialmente, se cortan los vidrios (cuya cara interna es conductora) y se limpian. Después se imprimen las pistas sobre el vidrio formando los píxeles. Estas pistas conductoras provienen del vidrio con la capa conductora de ITO (óxido de indio y estaño). Esto se hace a través de un proceso de fotolitografía con una resina fotosensible, y un desarrollo y ataque posterior del ITO sin protección. Más tarde, las caras internas de los vidrios se acondicionan depositando una capa, que puede ser orgánica o inorgánica (un polímero o un óxido). Esta etapa es crucial para el funcionamiento del dispositivo: induce la orientación de las moléculas de cristal líquido. Una vez que las superficies están acondicionadas, se depositan espaciadores en las mismas: son pequeñas esferas o cilindros de tamaño calibrado (pocos micrómetros) para garantizar un espesor homogéneo del dispositivo. Después en uno de los sustratos se deposita un adhesivo (gasket). A continuación, los sustratos se ensamblan teniendo en cuenta que el gasket debe dejar una boca libre para que el cristal líquido se introduzca posteriormente dentro de la célula. El llenado de la célula se realiza en una cámara de vacío y después la boca se sella. Por último, la conexión de los cables a la célula y el montaje de los polarizadores se realizan fuera de la sala limpia (Figura 1). Dependiendo de la aplicación, el cristal líquido empleado y los demás componentes de la célula tendrán unas características particulares. Para el diseño de los dispositivos de este trabajo se ha realizado un estudio de superficies inorgánicas de alineamiento del cristal líquido, que será de gran importancia para la preparación de los dispositivos de fase, dependiendo de las condiciones ambientales en las que vayan a trabajar. Los materiales inorgánicos que se han estudiado han sido en este caso SiOx y SiO2. El estudio ha comprendido tanto los factores de preparación influyentes en el alineamiento, el comportamiento del cristal líquido al variar estos factores y un estudio de la morfología de las superficies obtenidas.

CDAPubMed: a browser extension to retrieve EHR-based biomedical literature

Over the last few decades, the ever-increasing output of scientific publications has led to new challenges to keep up to date with the literature. In the biomedical area, this growth has introduced new requirements for professionals, e.g., physicians, who have to locate the exact papers that they need for their clinical and research work amongst a huge number of publications. Against this backdrop, novel information retrieval methods are even more necessary. While web search engines are widespread in many areas, facilitating access to all kinds of information, additional tools are required to automatically link information retrieved from these engines to specific biomedical applications. In the case of clinical environments, this also means considering aspects such as patient data security and confidentiality or structured contents, e.g., electronic health records (EHRs). In this scenario, we have developed a new tool to facilitate query building to retrieve scientific literature related to EHRs. Results: We have developed CDAPubMed, an open-source web browser extension to integrate EHR features in biomedical literature retrieval approaches. Clinical users can use CDAPubMed to: (i) load patient clinical documents, i.e., EHRs based on the Health Level 7-Clinical Document Architecture Standard (HL7-CDA), (ii) identify relevant terms for scientific literature search in these documents, i.e., Medical Subject Headings (MeSH), automatically driven by the CDAPubMed configuration, which advanced users can optimize to adapt to each specific situation, and (iii) generate and launch literature search queries to a major search engine, i.e., PubMed, to retrieve citations related to the EHR under examination. Conclusions: CDAPubMed is a platform-independent tool designed to facilitate literature searching using keywords contained in specific EHRs. CDAPubMed is visually integrated, as an extension of a widespread web browser, within the standard PubMed interface. It has been tested on a public dataset of HL7-CDA documents, returning significantly fewer citations since queries are focused on characteristics identified within the EHR. For instance, compared with more than 200,000 citations retrieved by breast neoplasm, fewer than ten citations were retrieved when ten patient features were added using CDAPubMed. This is an open source tool that can be freely used for non-profit purposes and integrated with other existing systems.

Orbital debris mitigation through deorbiting with passive electrodynamic drag

The increase of orbital debris and the consequent proliferation of smaller objects through fragmentation are driving the need for mitigation strategies. The issue is how to deorbit the satellite with an efficient system that does not impair drastically the propellant budget of the satellite and, consequently, reduces its operating life. We have been investigating, in the framework of a European-Community-funded project, a passive system that makes use of an electrodynamics tether to deorbit a satellite through Lorentz forces. The deorbiting system will be carried by the satellite itself at launch and deployed from the satellite at the end of its life. From that moment onward the system operates passively without requiring any intervention from the satellite itself. The paper summarizes the results of the analysis carried out to show the deorbiting performance of the system starting from different orbital altitudes and inclinations for a reference satellite mass. Results can be easily scaled to other satellite masses. The results have been obtained by using a high-fidelity computer model that uses the latest environmental routines for magnetic field, ionospheric density, atmospheric density and a gravity field model. The tether dynamics is modelled by considering all the main aspects of a real system as the tether flexibility and its temperature-dependent electrical conductivity. Temperature variations are computed by including all the major external and internal input fluxes and the thermal flux emitted from the tether. The results shows that a relatively compact and light system can carry out the complete deorbit of a relatively large satellite in a time ranging from a month to less than a year starting from high LEO with the best performance occurring at low orbital inclinations.

An approach to stakeholders involvement in the preparedness for nuclear and radiological emergency response & recovery in Spain

The elaboration of a generic decision-making strategy to address the evolution of an emergency situation, from the stages of response to recovery, and including a planning stage, can facilitate timely, effective and consistent decision making by the response organisations at every level within the emergency management structure and between countries, helping to ensure optimal protection of health, environment, and society. The degree of involvement of stakeholders in this process is a key strategic element for strengthening the local preparedness and response and can help a successful countermeasures strategy. A significant progress was made with the multi-national European project EURANOS (2004-2009) which brought together best practice, knowledge and technology to enhance the preparedness for Europe's response to any radiation emergency and long term contamination. The subsequent establishment of a European Technology Platform and the recent launch of the research project NERIS-TP ("Towards a self sustaining European Technology Platform (NERIS-TP) on Preparedness for Nuclear and Radiological Emergency Response and Recovery") are aimed to continue with the remaining tasks for gaining appropriate levels of emergency preparedness at local level in most European countries. One of the objectives of the NERIS-TP project is: Strengthen the preparedness at the local/national level by setting up dedicated fora and developing new tools or adapting the tools developed within the EURANOS projects (such as the governance framework for preparedness, the handbooks on countermeasures, the RODOS system, and the MOIRA DSS for long term contamination in catchments) to meet the needs of local communities. CIEMAT and UPM in close interaction with the Nuclear Safety Council will explore, within this project, the use and application in Spain of such technical tools, including other national tools and information and communication strategies to foster cooperation between local, national and international stakeholders. The aim is identify and involve relevant stakeholders in emergency preparedness to improve the development and implementation of appropriate protection strategies as part of the consequence management and the transition to recovery. In this paper, an overview of the "state of the art" on this area in Spain and the methodology and work Plan proposed by the Spanish group within the project NERIS to grow the stakeholder involvement in the preparedness to emergency response and recovery is presented.

Distributed Web Interface for Real-Time Spatial Audio Reproduction System

SSR es el acrónimo de SoundScape Renderer (tool for real-time spatial audio reproduction providing a variety of rendering algorithms), es un programa escrito en su mayoría en C++. El programa permite al usuario escuchar tanto sonidos grabados con anterioridad como sonidos en directo. El sonido o los sonidos se oirán, desde el punto de vista del oyente, como si el sonido se produjese en el punto que el programa decida, lo interesante de este proyecto es que el sonido podrá cambiar de lugar, moverse, etc. Todo en tiempo real. Esto se consigue sin modificar el sonido al grabarlo pero sí al emitirlo, el programa calcula las variaciones necesarias para que al emitir el sonido al oyente le llegue como si el sonido realmente se generase en un punto del espacio o lo más parecido posible. La sensación de movimiento no deja de ser el punto anterior cambiando de lugar. La idea era crear una aplicación web basada en Canvas de HTML5 que se comunicará con esta interfaz de usuario remota. Así se solucionarían todos los problemas de compatibilidad ya que cualquier dispositivo con posibilidad de visualizar páginas web podría correr una aplicación basada en estándares web, por ejemplo un sistema con Windows o un móvil con navegador. El protocolo debía de ser WebSocket porque es un protocolo HTML5 y ofrece las “garantías” de latencia que una aplicación con necesidades de información en tiempo real requiere. Nos permite una comunicación full-dúplex asíncrona sin mucho payload que es justo lo que se venía a evitar al no usar polling normal de HTML. El problema que surgió fue que la interfaz de usuario de red que tenía el programa no era compatible con WebSocket debido a un handshacking inicial y obligatorio que realiza el protocolo, por lo que se necesitaba otra interfaz de red. Se decidió entonces cambiar a JSON como formato para el intercambio de mensajes. Al final el proyecto comprende no sólo la aplicación web basada en Canvas sino también un servidor funcional y la definición de una nueva interfaz de usuario de red con su protocolo añadido. ABSTRACT. This project aims to become a part of the SSR tool to extend its capabilities in the field of the access. SSR is an acronym for SoundScape Renderer, is a program mostly written in C++ that allows you to hear already recorded or live sound with a variety of sound equipment as if the sound came from a desired place in the space. Like the web-page of the SSR says surely better explained: “The SoundScape Renderer (SSR) is a tool for real-time spatial audio reproduction providing a variety of rendering algorithms.” The application can be used with a graphical interface written in Qt but has also a network interface for external applications to use it. This network interface communicates using XML messages. A good example of it is the Android client. This Android client is already working. In order to use the application should be run it by loading an audio source and the wanted environment so that the renderer knows what to do. In that moment the server binds and anyone can use the network interface. Since the network interface is documented everyone can make an application to interact with this network interface. So the application can have as many user interfaces as wanted. The part that is developed in this project has nothing to do neither with audio rendering nor even with the reproduction of the spatial audio. The part that is developed here is about the interface used in the SSR application. As it can be deduced from the title: “Distributed Web Interface for Real-Time Spatial Audio Reproduction System”, this work aims only to offer the interface via web for the SSR (“Real-Time Spatial Audio Reproduction System”). The idea is not to make a new graphical interface for SSR but to allow more types of interfaces and communication. To accomplish the objective of allowing more graphical interfaces this project is going to use a new network interface. By now the SSR application is using only XML for data interchange but this new network interface support JSON. This project comprehends the server that launch the application, the user interface and the new network interface. It is done with these modules in order to allow creating new user interfaces that can communicate with the server or new servers that can communicate with the user interface by defining a complete network interface for data interchange.

Comparison of numerical models for vibro-acoustic analysis of structural panels in low modal density range engaging air layers

During launch, satellite and their equipment are subjected to loads of random nature and with a wide frequency range. Their vibro-acoustic response is an important issue to be analysed, for example for folded solar arrays and antennas. The main issue at low modal density is the modelling combinations engaging air layers, structures and external fluid. Depending on the modal density different methodologies, as FEM, BEM and SEA should be considered. This work focuses on the analysis of different combinations of the methodologies previously stated used in order to characterise the vibro-acoustic response of two rectangular sandwich structure panels isolated and engaging an air layer between them under a diffuse acoustic field. Focusing on the modelling of air layers, different models are proposed. To illustrate the phenomenology described and studied, experimental results from an acoustic test on an ARA-MKIII solar array in folded configuration are presented along with numerical results.

Criteria for mathematical model selection for satellite vibro-acoustic analysis depending on frequency range

Satellites and space equipment are exposed to diffuse acoustic fields during the launch process. The use of adequate techniques to model the response to the acoustic loads is a fundamental task during the design and verification phases. Considering the modal density of each element is necessary to identify the correct methodology. In this report selection criteria are presented in order to choose the correct modelling technique depending on the frequency ranges. A model satellite’s response to acoustic loads is presented, determining the modal densities of each component in different frequency ranges. The paper proposes to select the mathematical method in each modal density range and the differences in the response estimation due to the different used techniques. In addition, the methodologies to analyse the intermediate range of the system are discussed. The results are compared with experimental testing data obtained in an experimental modal test.

Five-year results of a slant-path propagation experiment at 20 GHz in Madrid

Satellite operators are starting to use the Ka-band (30/20 GHz) for communications systems requiring higher traffic capacity. The use of this band is expected to experience a significant growth in the next few years, as several operators have reported plans to launch new satellites with Ka-band capacity. It is worth mentioning the Ka-Sat satellite in Europe, launched in 2010, and ViaSat-1, of 2011, with coverage of USA1. Some other examples can be found in other parts of the World. Recent satellite communications standards, such as DVB-S22 or DVB-RCS3, which provide means to mitigate propagation impairments, have been developed with the objective of improving the use of the Ka-band, in comparison with previous technical standards. In the next years, the ALPHASAT satellite will bring about new opportunities4 for carrying out propagation and telecommunication experiments in the Ka- and Q/V-bands. Commercial uses are focused on the provision of high speed data communications, for Internet access and other applications. In the near future, it is expected that higher and higher data rates will also be needed to broadcast richer multimedia contents, including HD-TV, interactive content or 3D-TV. All of these services may be provided in the future by satellites of the current generation, whose life span can extend up to 2025 in some cases. Depending on local regulations, the available bandwidth for the satellite fixed and broadcasting services in the Ka-band is in excess of several hundred MHz, bidirectional, comprising more than 1 GHz for each sub-band in some cases. In this paper, the results of a propagation experiment that is being carried out at Universidad Politécnica de Madrid (UPM), Spain, are presented5. The objective of the experiment is twofold: gathering experimental time series of attenuation and analyzing them in order to characterize the propagation channel at these frequencies6. The experiment and statistical results correspond to five complete years of measurements. The experiment is described in more detail in Section II. Yearly characteristics of rain attenuation are presented in Section III, whereas Section IV is dedicated to the monthly, seasonal, and hourly characteristics. Section V covers the dynamic characteristics of this propagation effect, just before the conclusions are described in Section VI.