A theoretical study on the formation of iodine oxide aggregates and monohydrates

Biotic and abiotic emissions of molecular iodine and iodocarbons from the sea or the ice surface and the intertidal zone to the coastal/polar marine boundary layer lead to the formation of iodine oxides, which subsequently nucleate forming iodine oxide particles (IOPs). Although the link between coastal iodine emissions and ultrafine aerosol bursts is well established, the details of the nucleation mechanism have not yet been elucidated. In this paper, results of a theoretical study of a range of potentially relevant aggregation reactions of different iodine oxides, as well as complexation with water molecules, are reported. Thermochemical properties of these reactions are obtained from high level ab initio correlated calculations including spin–orbit corrections. The results show that the nucleation path most likely proceeds through dimerisation of I2O4. It is also shown that water can hinder gas-to-particle conversion to some extent, although complexation with key iodine oxides does not remove enough of these to stop IOP formation. A consistent picture of this process emerges from the theoretical study presented here and the findings of a new laboratory study reported in the accompanying paper (Gomez Martin et al., 2013).

Water seepage beneath dams on soluble evaporite deposits: a laboratory and field study (Caspe Dam, Spain)

The paper presents analytical methods and results for assessing the variation in the concentration of sulphate (and other ions) over space and time in groundwater flowing through a soluble evaporite terrain beneath a dam. The influence of effective porosity, groundwater flow velocity and the specific rate of dissolution (K′) are considered. The theoretical analysis was tested in a scale model simulating a dam constructed on heavily karstified bedrock. A simple and useful method for assessing how much material is lost through dissolution and how the rate of dissolution changes over time is considered in the context of the Caspe Dam, Spain.

Plasma kinetics issues in an ESA study for a plasma laboratory in space

A study supported by the European Space Agency (ESA), in the context of its General Studies Programme, performed an investigation of the possible use of space for studies in pure and applied plasma physics, in areas not traditionally covered by ‘space plasma physics’. A set of experiments have been identified that can potentially provide access to new phenomena and to allow advances in several fields of plasma science. These experiments concern phenomena on a spatial scale (101–104 m) intermediate between what is achievable on the ground and the usual solar system plasma observations. Detailed feasibility studies have been performed for three experiments: active magnetic experiments, largescale discharges and long tether–plasma interactions. The perspectives opened by these experiments are discussed for magnetic reconnection, instabilities, MHD turbulence, atomic excited states kinetics, weakly ionized plasmas,plasma diagnostics, artificial auroras and atmospheric studies. The discussion is also supported by results of numerical simulations and estimates.

The ESA "Plasma Laboratory in Space" study

The European Space Agency has initiated, in the context of its General Studies Programme, a study of the possible use of space for studies in pure and applied plasma physics, in areas not traditionally covered by “space plasma physics”. A team of experts has been set-up to review a broad range of area including industrial plasma physics and pure plasma physics, astrophysical and solar-terrestrial areas. A set of experiments have been identified that can potentially provide access to new phenomena and to allow advances in several fields of plasma science. These experiments concern phenomena on spatial scale (102 to104 m) intermediate between what is achievable on ground experiment and usual solar system plasma observations.

Estudio experimental del Sistema de Albañilería Integral en la construcción de viviendas sismorresistentes. Experimental study of the Integral Masonry System in the construction of earthquake resistant houses

This paper presents the application of the Integral Masonry System (IMS) to the construction of earthquake resistant houses and its experimental study. To verify the security of this new type of building in seismic areas of the third world two prototypes have been tested, one with adobe and the other with hollow brick. In both cases it’s a two-story 6x6x6 m3 house built to scale 1/2. The tests are carried out at the Laboratory of Antiseismic Structures of the Department of Engineering, Pontifical Catholic University of Peru in Lima, in collaboration with the UPM (Technical University of Madrid). This article shows the design process of the prototypes to test, including the sizing of the reinforcements, the characteristics of the tests and the results obtained. These results show that the IMS with adobe or brick remains stable with no significant cracks faced with a severe earthquake, with an estimated acceleration of 1.8 g. Este artículo presenta una aplicación del Sistema de Albañilería Integral (SAI) a la construcción de viviendas sismorresistentes y su estudio experimental. Para verificar su seguridad para su construcción en zonas sísmicas del tercer mundo se han ensayado dos prototipos, uno con adobe, y otro con ladrillo hueco. Se trata de una vivienda de 6x6x6 m3 y dos plantas que se construyen a escala 1/2. Los ensayos se realizaron en el Laboratorio de Estructuras Antisísmicas del Departamento de Ingeniería de la Pontificia Católica Universidad del Perú (PUCP) de Lima en colaboración con la UPM (Universidad Politécnica de Madrid). Este artículo muestra el proceso de diseño de los prototipos a ensayar, incluido el dimensionado de los refuerzos, las características de los ensayos y los resultados obtenidos. Estos resultados muestran que el SAI con adobe o ladrillo permanece estable sin grietas significativas ante un sismo severo, con una aceleración estimada de 1,8 g.

Migration to an a on.line laboratory in mechanical engineering. The case of a cam follower design practice.

The European Higher Education Area (EHEA) has leaded to a change in the way the subjects are taught. One of the more important aspects of the EHEA is to support the autonomous study of the students. Taking into account this new approach, the virtual laboratory of the subject Mechanisms of the Aeronautical studies at the Technical University of Madrid is being migrated to an on-line scheme. This virtual laboratory consist on two practices: the design of cam-follower mechanisms and the design of trains of gears. Both practices are software applications that, in the current situation, need to be installed on each computer and the students carry out the practice at the computer classroom of the school under the supervision of a teacher. During this year the design of cam-follower mechanisms practice has been moved to a web application using Java and the Google Development Toolkit. In this practice the students has to design and study the running of a cam to perform a specific displacement diagram with a selected follower taking into account that the mechanism must be able to work properly at high speed regime. The practice has maintained its objectives in the new platform but to take advantage of the new methodology and try to avoid the inconveniences that the previous version had shown. Once the new practice has been ready, a pilot study has been carried out to compare both approaches: on-line and in-lab. This paper shows the adaptation of the cam and follower practice to an on-line methodology. Both practices are described and the changes that has been done to the initial one are shown. They are compared and the weak and strong points of each one are analyzed. Finally we explain the pilot study carried out, the students impression and the results obtained.

Student Reciprocal Peer Teaching as a Method for Active Learning: An Experience in an Electrotechnical Laboratory

Active learning is one of the most efficient mechanisms for learning, according to the psychology of learning. When students act as teachers for other students, the communication is more fluent and knowledge is transferred easier than in a traditional classroom. This teaching method is referred to in the literature as reciprocal peer teaching. In this study, the method is applied to laboratory sessions of a higher education institution course, and the students who act as teachers are referred to as ‘‘laboratory monitors.’’ A particular way to select the monitors and its impact in the final marks is proposed. A total of 181 students participated in the experiment, experiences with laboratory monitors are discussed, and methods for motivating and training laboratory monitors and regular students are proposed. The types of laboratory sessions that can be led by classmates are discussed. This work is related to the changes in teaching methods in the Spanish higher education system, prompted by the Bologna Process for the construction of the European Higher Education Area

Estudio de las formas de aplicación de la fotografía sobre los materiales pétreos para la arquitectura = Study of photography application methods over architectural stony materials

Desde que el Hombre era morador de las cavernas ha sido manifiesto su deseo innato por grabar y reproducir "instantáneas con las que perpetuarse o sobre las que mirarse ". La aparición y desarrollo de la fotografía como medio para poder captar y fijar "la imagen directa de la realidad circundante " pronto se convierte en un nuevo lenguaje estético y poético que permite al artista la interpretación y reflexión de lo observado. Se imprime a la imagen el carácter de la mirada del fotógrafo, estableciendo un diálogo conceptual con el juego de luces. La presente Tesis plantea la creación de una nueva piel de arquitectura mediante la impresión fotográfica sobre materiales pétreos. La búsqueda de la expresividad de los materiales como soporte de expresión artística implica un cambio de escala al trasladar la instantánea fotográfica a la arquitectura y la aplicación de un nuevo soporte al imprimir la fotografía sobre materiales arquitectónicos. Se justifica la elección del dispositivo láser CO2 como sistema de impresión fotográfica sobre los materiales pétreos arquitectónicos, como la técnica que permite la unión física de la imagen y el proyecto arquitectónico, generando un valor añadido a través del arte de la fotografía. Se justifica la elección de los materiales investigados, Silestone® Blanco Zeus y GRC® con TX Active® Aria, de forma que la investigación de esta nueva piel de arquitectura abarca tanto la envolvente del edificio como su volumen interior, permitiendo cerrar el círculo arquitectónico "in&out" y dota al proyecto arquitectónico de un valor añadido al introducir conceptos sostenibles de carácter estético y medioambiental. Se realiza una consulta a las empresas del sector arquitectónico relacionadas directamente con la producción y distribución de los materiales Silestone® y GRC®, así como a las empresas especializadas en sistemas de impresión fotográfica sobre materiales, acerca del estado del arte. Se recorre la Historia de la fotografía desde sus orígenes hasta el desarrollo de la era digital y se analiza su condición artística. Se recopilan los sistemas de impresión fotográfica que han evolucionado en paralelo con los dispositivos de captura de la instantánea fotográfica y se describe en profundidad el sistema de impresión fotográfica mediante dispositivo láser CO2. Se describen los procesos de fabricación, las características técnicas, cualidades y aplicaciones de los materiales pétreos arquitectónicos Silestone® Blanco Zeus y GRC® con TX Active® Aria. Se explica la técnica utilizada para la captación de la imagen fotográfica, su justificación artística y su proceso de impresión mediante dispositivo láser CO2 bajo diferentes parámetros sobre muestras de los materiales arquitectónicos investigados. Se comprueba la viabilidad de desarrollo de la nueva piel de arquitectura sobre Silestone® Blanco Zeus y GRC® con TX Active® Aria sometiendo a las piezas impresas bajo diferentes parámetros a tres ensayos de laboratorio. En cada uno de ellos se concreta el objetivo y procedimiento del ensayo, la enumeración de las muestras ensayadas y los parámetros bajo los que han sido impresas, el análisis de los resultados del ensayo y las conclusiones del ensayo. Ensayo de amplitud térmica. Se determina el grado de afectación de las imágenes impresas bajo la acción de contrastes térmicos. Series de muestras de Silestone® Blanco Zeus y GRC® con TX Active® Aria impresas con láser CO2 se someten a ciclos de contraste frío-calor de 12 horas de duración para una amplitud térmica total de 102°C. Se realiza una toma sistemática de fotografías microscópicas con lupa de aumento de cada pieza antes y después de los ciclos frío-calor y la observación de las transformaciones que experimentan los materiales bajo la acción del láser CO2. Ensayo de exposición a la acción de la radiación ultravioleta (UV). Se determina el grado de afectación de las imágenes impresas al activar la capacidad autolimpiante de partículas orgánicas. Una serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a ciclos de exposición de radiación ultravioleta de 26 horas de duración. Se somete la serie a un procedimiento de activación del aditivo TX Active®. Se simula la contaminación orgánica mediante la aplicación controlada de Rodamina B, tinte orgánico, y se simula la radiación UV mediante el empleo de una bombilla de emisión de rayos ultravioleta. Se realiza una toma sistemática de fotografías macroscópicas de la serie de muestras ensayadas: antes de aplicación de la Rodamina B, momento 00:00h, momento 04:00h y momento 26:00h del ensayo. Se procede a la descarga y análisis del histograma de las fotografías como registro de la actividad fotocatalítica. Ensayo de la capacidad autodescontaminante del GRC® con TX Active® impreso con láser CO2. Se comprueba si la capacidad autodescontaminante del GRC® con TX Active® se ve alterada como consecuencia de la impresión de la imagen fotográfica impresa con láser CO2. Serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a test de capacidad autodescontaminante: atmósfera controlada y contaminada con óxidos de nitrógeno en los que se coloca cada pieza ensayada bajo la acción de una lámpara de emisión de radiación ultravioleta (UV). Se registra la actividad fotocatalítica en base a la variación de concentración de óxido de nitrógeno. Se recopila el análisis e interpretación de los resultados de los ensayos de laboratorio y se elaboran las conclusiones generales de la investigación. Se sintetizan las futuras líneas de investigación que, a partir de las investigaciones realizadas y de sus conclusiones generales, podrían desarrollarse en el ámbito de la impresión fotográfica sobre materiales arquitectónicos. Se describe el rendimiento tecnológico y artístico generado por las investigaciones previas que han dado origen y desarrollo a la Tesis Doctoral. ABSTRACT Since ancient time, humanity has been driven by an innate wish to reproduce and engrave "snapshots that could help to perpetúate or to look at one self". Photography's birth and its development as a mean to capture and fix "the direct image of the surrounding reality" quickly becomes a new aesthetical and poetical language allowing the artist to interpret and think over what has been observed. The photographer's eye is imprinted onto the image, and so the conceptual dialogue between the artist and the light beams begins. The current thesis suggests the creation of a new architectural skin through photography imprinting over stony materials. The search for material's expressiveness as a medium of artistic expression involves a change of scale as it transfers photographic snapshot into architecture and the use of a new photographic printing support over architectural materials. CO2 laser is the chosen printing system for this technique as it allows the physical union of the image and the architectonic project, generating an added value through the art of photography. The researched materials selected were Silestone®, Blanco Zeus and GRC® with TX Active® Aria. This new architectural skin contains the building surrounding as well as its interior volume, closing the architectonic "in & out" circle and adding a value to the project by introducing aesthetical and environmental sustainable concepts. Architecture companies related to the production and distribution of materials like Silestone® and GRC®, as well as companies specialized in photography printing over materials were consulted to obtain a State of the Art. A thorough analysis of photography's History from its origins to the digital era development was made and its artistic condition was studied in this thesis. In this study the author also makes a compilation of several photographic printing systems that evolved together with photographic snapshot devices. The CO2 laser-based photographic printing system is also described in depth. Regarding stony materials of architecture like Silestone®, Blanco Zeus and GRC® with TX Active® Aria, the present study also describes their manufacture processes as well as technical features, quality and application. There is also an explanation about the technique to capture the photographic image, its artistic justification and its CO2 laser-based printing system over the researched materials under different parameters. We also tested the feasibility of this new architectural skin over Silestone® Blanco Zeus and GRC® with TX Active® Aria. The pieces were tested under different parameters in three laboratory trials. Each trial comprises of an explanation of its objective and its process, the samples were numbered and the printing parameters were specified. Finally, with the analysis of the results some conclusions were drawn. In the thermal amplitude trial we tried to determine how printed images were affected as a result of the action of thermal contrasts. Series of samples of Silestone® Blanco Zeus and GRC® with TX Active® Aria printed with CO2 laser were subjected to several 12h warm-cold cycles for thermal total amplitude of 102oc. Each sample was captured systematically with microscopic enhanced lenses before and after cold-warm cycles. The changes experienced by these materials under the effect of CO2 laser were observed and recorded. Trial regarding the Ultraviolet Radiation (UR) effect on images. We determined to which extent printed images were affected once the self-cleaning organic particles were activated. This time GRC® with TX Active® Aria samples printed with CO2 laser were exposed to a 26h UR cycle. The samples were subjected to the activation of TX Active® additive. Through the controlled application of Rodamine B and organic dye we were able to simulate the organic contamination process. UR was simulated using an ultraviolet beam emission bulb. A systematic capture of macroscopic pictures of the tested sample series was performed at different time points: before Rodamine B application, at moment 00:00h, moment 04:00h and moment 26:00h of the trial. Picture's histogram was downloaded and analyzed as a log of photocatalytic activity. Trial regarding the self-decontaminating ability of GRC® with TX Active® printed with CO2 laser. We tested if this self-decontaminating ability is altered as a result of CO2 laser printed image. GRC® with TX Active® Aria samples printed with CO2 laser, were subject to self-decontaminating ability tests with controlled and nitrogen oxide contaminated atmosphere. Each piece was put under the action of an UR emission lamp. Photocatalytic activity was recorded according to the variation in nitrogen oxide concentration. The results of the trial and their interpretation as well as the general conclusions of the research are also compiled in the present study. Study conclusions enable to draw future research lines of potential applications of photographic printing over architecture materials. Previous research generated an artistic and technological outcome that led to the development of this doctoral thesis.

On track for solar grade silicon through a siemens process-type laboratory reactor: operating conditions and energy savings

Polysilicon cost impacts significantly on the photovoltaics (PV) cost and on the energy payback time. Nowadays, the besetting production process is the so called Siemens process, polysilicon deposition by chemical vapor deposition (CVD) from Trichlorosilane. Polysilicon purification level for PV is to a certain extent less demanding that for microelectronics. At the Instituto de Energía Solar (IES) research on this subject is performed through a Siemens process-type laboratory reactor. Through the laboratory CVD prototype at the IES laboratories, valuable information about the phenomena involved in the polysilicon deposition process and the operating conditions is obtained. Polysilicon deposition by CVD is a complex process due to the big number of parameters involved. A study on the influence of temperature and inlet gas mixture composition on the polysilicon deposition growth rate, based on experimental experience, is shown. Moreover, CVD process accounts for the largest contribution to the energy consumption of the polysilicon production. In addition, radiation phenomenon is the major responsible for low energetic efficiency of the whole process. This work presents a model of radiation heat loss, and the theoretical calculations are confirmed experimentally through a prototype reactor at our disposal, yielding a valuable know-how for energy consumption reduction at industrial Siemens reactors.

Seismic performance case study of bridge pile cap foundation

The purpose of this report is to build a model that represents, as best as possible, the seismic behavior of a pile cap bridge foundation by a nonlinear static (analysis) procedure. It will consist of a reproduction of a specimen already built in the laboratory. This model will carry out a pseudo static lateral and horizontal pushover test that will be applied onto the pile cap until the failure of the structure, the formation of a plastic hinge in the piles due to the horizontal deformation, occurs. The pushover test consists of increasing the horizontal load over the pile cap until the horizontal displacement wanted at the height of the pile cap is reached. The output of this model will be a Skeleton curve that will plot the lateral load (kN) over the displacement (m), so that the maximum movement the pile cap foundation can reach before its failure can be calculated. This failure will be achieved when the load at that specific shift is equal to 85% of the maximum. The pile cap foundation finite element model was based on pile cap built for a laboratory experiment already carried out by the Master student Deming Zhang at Tongji University. Two different pile caps were tested with a difference in height above the ground level. While one has 0:3m, the other rises 0:8m above the ground level. The computer model was calibrated using the experimental results. The pile cap foundation will be programmed in a finite element environment called OpenSees (Open System for Earthquake Engineering Simulation [28]). This environment is a free software developed by Berkeley University specialized, as it name says, in the study of earthquakes and its effects on structures. This specialization is the main reason why it is being used for building this model as it makes it possible to build any finite element model, and perform several analysis in order to get the results wanted. The development of OpenSees is sponsored by the Pacific Earthquake Engineering Research Center through the National Science Foundation engineering and education centers program. OpenSees uses Tcl language to program it, which is a language similar to C++.

Determination and analysis of plasma radiative properties for numerical simulations of laboratory radiative blast waves launched in xenon clusters

Radiative shock waves play a pivotal role in the transport energy into the stellar medium. This fact has led to many efforts to scale the astrophysical phenomena to accessible laboratory conditions and their study has been highlighted as an area requiring further experimental investigations. Low density material with high atomic mass is suitable to achieve radiative regime, and, therefore, low density xenon plasmas are commonly used for the medium in which the radiative shocks propagate. The knowledge of the plasma radiative properties is crucial for the correct understanding and for the hydrodynamic simulations of radiative shocks. In this work, we perform an analysis of the radiative properties of xenon plasmas in a range of matter densities and electron temperatures typically found in laboratory experiments of radiative shocks launched in xenon plasmas. Furthermore, for a particular experiment, our analysis is applied to make a diagnostics of the electron temperatures of the radiative shocks since they could not be experimentally measured

Case study on mobile applications UX: effect of the usage of a crosss-platform development framework

Cross-platform development frameworks for mobile applications promise important advantages in cost cuttings and easy maintenance, posing as a very good option for organizations interested in the design of mobile applications for several platforms. Given that platform conventions are especially important for the User eXperience (UX) of mobile applications, the usage of framework where the same code defines the behavior of the app in different platforms could have negative impact in the UX. The objetive of this study is comparing the cross-platform and the native approach for being able to determine if the selected development approach has any impact on the users in terms of UX. To be able to set a base line under this subject, study on cross-platform frameworks was performed to select the most appropriate one from a UX point of view. In order to achieve the objectives of this work, two development teams have developed two versions of the same application; one using framework that generates Android and iOS versions automatically, and another team developing native versions of the same application. The alternative versions for each platform have been evaluated with 37 users with a combination of a laboratory usability test and a longitudinal study. The results show that differences are minimal in the Android version, but in iOS, even if a reasonable good UX can be obtained with the usage of this framework by an UX-conscious design team, a higher level of UX can be obtained directly developing in native code.

Experimental and numerical study of cracking of concrete due to reinforcement corrosion

La corrosión del acero es una de las patologías más importantes que afectan a las estructuras de hormigón armado que están expuestas a ambientes marinos o al ataque de sales fundentes. Cuando se produce corrosión, se genera una capa de óxido alrededor de la superficie de las armaduras, que ocupa un volumen mayor que el acero inicial; como consecuencia, el óxido ejerce presiones internas en el hormigón circundante, que lleva a la fisuración y, ocasionalmente, al desprendimiento del recubrimiento de hormigón. Durante los últimos años, numerosos estudios han contribuido a ampliar el conocimiento sobre el proceso de fisuración; sin embargo, aún existen muchas incertidumbres respecto al comportamiento mecánico de la capa de óxido, que es fundamental para predecir la fisuración. Por ello, en esta tesis se ha desarrollado y aplicado una metodología, para mejorar el conocimiento respecto al comportamiento del sistema acero-óxido-hormigón, combinando experimentos y simulaciones numéricas. Se han realizado ensayos de corrosión acelerada en condiciones de laboratorio, utilizando la técnica de corriente impresa. Con el objetivo de obtener información cercana a la capa de acero, como muestras se seleccionaron prismas de hormigón con un tubo de acero liso como armadura, que se diseñaron para conseguir la formación de una única fisura principal en el recubrimiento. Durante los ensayos, las muestras se equiparon con instrumentos especialmente diseñados para medir la variación de diámetro y volumen interior de los tubos, y se midió la apertura de la fisura principal utilizando un extensómetro comercial, adaptado a la geometría de las muestras. Las condiciones de contorno se diseñaron cuidadosamente para que los campos de corriente y deformación fuesen planos durante los ensayos, resultando en corrosión uniforme a lo largo del tubo, para poder reproducir los ensayos en simulaciones numéricas. Se ensayaron series con varias densidades de corriente y varias profundidades de corrosión. De manera complementaria, el comportamiento en fractura del hormigón se caracterizó en ensayos independientes, y se midió la pérdida gravimétrica de los tubos siguiendo procedimientos estándar. En todos los ensayos, la fisura principal creció muy despacio durante las primeras micras de profundidad de corrosión, pero después de una cierta profundidad crítica, la fisura se desarrolló completamente, con un aumento rápido de su apertura; la densidad de corriente influye en la profundidad de corrosión crítica. Las variaciones de diámetro interior y de volumen interior de los tubos mostraron tendencias diferentes entre sí, lo que indica que la deformación del tubo no fue uniforme. Después de la corrosión acelerada, las muestras se cortaron en rebanadas, que se utilizaron en ensayos post-corrosión. El patrón de fisuración se estudió a lo largo del tubo, en rebanadas que se impregnaron en vacío con resina y fluoresceína para mejorar la visibilidad de las fisuras bajo luz ultravioleta, y se estudió la presencia de óxido dentro de las grietas. En todas las muestras, se formó una fisura principal en el recubrimiento, infiltrada con óxido, y varias fisuras secundarias finas alrededor del tubo; el número de fisuras varió con la profundidad de corrosión de las muestras. Para muestras con la misma corrosión, el número de fisuras y su posición fue diferente entre muestras y entre secciones de una misma muestra, debido a la heterogeneidad del hormigón. Finalmente, se investigó la adherencia entre el acero y el hormigón, utilizando un dispositivo diseñado para empujar el tubo en el hormigón. Las curvas de tensión frente a desplazamiento del tubo presentaron un pico marcado, seguido de un descenso constante; la profundidad de corrosión y la apertura de fisura de las muestras influyeron notablemente en la tensión residual del ensayo. Para simular la fisuración del hormigón causada por la corrosión de las armaduras, se programó un modelo numérico. Éste combina elementos finitos con fisura embebida adaptable que reproducen la fractura del hormigón conforme al modelo de fisura cohesiva estándar, y elementos de interfaz llamados elementos junta expansiva, que se programaron específicamente para reproducir la expansión volumétrica del óxido y que incorporan su comportamiento mecánico. En el elemento junta expansiva se implementó un fenómeno de despegue, concretamente de deslizamiento y separación, que resultó fundamental para obtener localización de fisuras adecuada, y que se consiguió con una fuerte reducción de la rigidez tangencial y la rigidez en tracción del óxido. Con este modelo, se realizaron simulaciones de los ensayos, utilizando modelos bidimensionales de las muestras con elementos finitos. Como datos para el comportamiento en fractura del hormigón, se utilizaron las propiedades determinadas en experimentos. Para el óxido, inicialmente se supuso un comportamiento fluido, con deslizamiento y separación casi perfectos. Después, se realizó un ajuste de los parámetros del elemento junta expansiva para reproducir los resultados experimentales. Se observó que variaciones en la rigidez normal del óxido apenas afectaban a los resultados, y que los demás parámetros apenas afectaban a la apertura de fisura; sin embargo, la deformación del tubo resultó ser muy sensible a variaciones en los parámetros del óxido, debido a la flexibilidad de la pared de los tubos, lo que resultó fundamental para determinar indirectamente los valores de los parámetros constitutivos del óxido. Finalmente, se realizaron simulaciones definitivas de los ensayos. El modelo reprodujo la profundidad de corrosión crítica y el comportamiento final de las curvas experimentales; se comprobó que la variación de diámetro interior de los tubos está fuertemente influenciada por su posición relativa respecto a la fisura principal, en concordancia con los resultados experimentales. De la comparación de los resultados experimentales y numéricos, se pudo extraer información sobre las propiedades del óxido que de otra manera no habría podido obtenerse. Corrosion of steel is one of the main pathologies affecting reinforced concrete structures exposed to marine environments or to molten salt. When corrosion occurs, an oxide layer develops around the reinforcement surface, which occupies a greater volume than the initial steel; thus, it induces internal pressure on the surrounding concrete that leads to cracking and, eventually, to full-spalling of the concrete cover. During the last years much effort has been devoted to understand the process of cracking; however, there is still a lack of knowledge regarding the mechanical behavior of the oxide layer, which is essential in the prediction of cracking. Thus, a methodology has been developed and applied in this thesis to gain further understanding of the behavior of the steel-oxide-concrete system, combining experiments and numerical simulations. Accelerated corrosion tests were carried out in laboratory conditions, using the impressed current technique. To get experimental information close to the oxide layer, concrete prisms with a smooth steel tube as reinforcement were selected as specimens, which were designed to get a single main crack across the cover. During the tests, the specimens were equipped with instruments that were specially designed to measure the variation of inner diameter and volume of the tubes, and the width of the main crack was recorded using a commercial extensometer that was adapted to the geometry of the specimens. The boundary conditions were carefully designed so that plane current and strain fields were expected during the tests, resulting in nearly uniform corrosion along the length of the tube, so that the tests could be reproduced in numerical simulations. Series of tests were carried out with various current densities and corrosion depths. Complementarily, the fracture behavior of concrete was characterized in independent tests, and the gravimetric loss of the steel tubes was determined by standard means. In all the tests, the main crack grew very slowly during the first microns of corrosion depth, but after a critical corrosion depth it fully developed and opened faster; the current density influenced the critical corrosion depth. The variation of inner diameter and inner volume of the tubes had different trends, which indicates that the deformation of the tube was not uniform. After accelerated corrosion, the specimens were cut into slices, which were used in post-corrosion tests. The pattern of cracking along the reinforcement was investigated in slices that were impregnated under vacuum with resin containing fluorescein to enhance the visibility of cracks under ultraviolet lightening and a study was carried out to assess the presence of oxide into the cracks. In all the specimens, a main crack developed through the concrete cover, which was infiltrated with oxide, and several thin secondary cracks around the reinforcement; the number of cracks diminished with the corrosion depth of the specimen. For specimens with the same corrosion, the number of cracks and their position varied from one specimen to another and between cross-sections of a given specimen, due to the heterogeneity of concrete. Finally, the bond between the steel and the concrete was investigated, using a device designed to push the tubes of steel in the concrete. The curves of stress versus displacement of the tube presented a marked peak, followed by a steady descent, with notably influence of the corrosion depth and the crack width on the residual stress. To simulate cracking of concrete due to corrosion of the reinforcement, a numerical model was implemented. It combines finite elements with an embedded adaptable crack that reproduces cracking of concrete according to the basic cohesive model, and interface elements so-called expansive joint elements, which were specially designed to reproduce the volumetric expansion of oxide and incorporate its mechanical behavior. In the expansive joint element, a debonding effect was implemented consisting of sliding and separation, which was proved to be essential to achieve proper localization of cracks, and was achieved by strongly reducing the shear and the tensile stiffnesses of the oxide. With that model, simulations of the accelerated corrosion tests were carried out on 2- dimensional finite element models of the specimens. For the fracture behavior of concrete, the properties experimentally determined were used as input. For the oxide, initially a fluidlike behavior was assumed with nearly perfect sliding and separation; then the parameters of the expansive joint element were modified to fit the experimental results. Changes in the bulk modulus of the oxide barely affected the results and changes in the remaining parameters had a moderate effect on the predicted crack width; however, the deformation of the tube was very sensitive to variations in the parameters of oxide, due to the flexibility of the tube wall, which was crucial for indirect determination of the constitutive parameters of oxide. Finally, definitive simulations of the tests were carried out. The model reproduced the critical corrosion depth and the final behavior of the experimental curves; it was assessed that the variation of inner diameter of the tubes is highly influenced by its relative position with respect to the main crack, in accordance with the experimental observations. From the comparison of the experimental and numerical results, some properties of the mechanical behavior of the oxide were disclosed that otherwise could not have been measured.

A case study on cross-platform development frameworks for mobile applications and UX

Cross-platform development frameworks for mobile applications promise important advantages in cost cuttings and easy maintenance, posing as a very good option for organizations interested in the design of mobile applications for several platforms. Given that platform conventions are especially important for the User eXperience (UX) of mobile applications, the usage of a framework where the same code defines the behavior of the app in different platforms could have a negative impact in the UX. This paper describes a study where two independent teams have designed two different versions of a mobile application, one using a framework that generates Android and iOS versions automatically, and another team using native tools. The alternative versions for each platform have been evaluated with 37 users with a combination of a laboratory usability test and a longitudinal study. The results show that differences are minimal in the Android platform, but in iOS, even if a reasonably good UX can be obtained with the usage of this framework by an UX-conscious design team, a higher level of UX can be obtained directly developing with a native tool.