Terapia por láser de baja potencia: consideraciones óptico-físicas y biológicas determinantes en su aplicación clínica.

Objetivos : Analizar la distribución de energía en un tejido cuando se emplea terapia por láser de baja potencia y estudiar las especificaciones mínimas de equipos de terapia láser para estimar la dosis. Material y métodos: Se ha empleado el método de Monte Carlo para obtener la distribución de energía absorbida por la piel para dos tipos de láser y la teoría de la difusión para estimar la longitud de penetración y el recorrido libre medio. Se ha estudiado la variación de esa distribución en función de la raza (caucásico, asiático, afroamericano) y para dos localizaciones anatómicas distintas. Se ha analizado la información facilitada por diversos fabricantes de equipos comerciales para determinar si es necesario adaptar la dosimetría recomendada. Resultados: La radiación láser infrarroja (810nm) se absorbe mayoritariamente en un espesor de piel de 1,9±0,2mm para caucásicos, entre 1,73±0,08mm (volar del antebrazo) y 1,80±0,11mm (palma) para asiáticos y entre 1,25±0,09mm (volar del antebrazo) y 1,65±0,2mm (palma) para afroamericanos. El recorrido libre medio de la luz siempre es menor que 0,69±0,09mm. Para los equipos comerciales analizados la única característica geométrica del haz láser que se menciona es la superficie que oscila entre 0,08 y 1cm2, pero no se especifica cómo es la distribución de energía, la divergencia del haz, forma de la sección transversal, etc. Conclusiones:Dependiendo del equipo de terapia por láser de baja potencia utilizado, el tipo de paciente y la zona a tratar, el clínico debe adaptar las dosis recomendadas. Abstract: Objectives: To analyze the distribution of energy deposited in a tissue when this is irradiated with a low power laser and to study the minimum characteristics that manufacturers of low power laser therapy equipments should include to estimate the dosage. Material and methods: Monte Carlo simulation was performed to determine the absorption location of the laser energy. The diffusion theory was used to estimate penetration depth and mean free path. Variation of this distribution was studied based on three different skin types (Caucasians, Asians and Afroamericans) and for two different anatomic locations: palm and volar forearm. Information given by several manufactures of low power laser therapy equipments has been analyzed. Results: Infrared (810 nm) laser radiation is mainly absorbed in a skin layer of thickness 1.9±0.2mm for Caucasians, from 1.73±0.08mm (volar forearm) to 1.80±0.11mm (palm) for Asians, and from 1.25±0.09mm (volar forearm) to 1.65±0.2mm (palm) for Afroamericans. The light mean free path is lower than 0.69±0.09mm for all cases. The laser beam characteristics (beam shape, energy distribution on a transversal section, divergence, incidence angle,etc.) are not usually specified by the manufacturers. Only beam size (ranging from 0.08 to 1cm2) is given in some cases. Discussion and conclusions: Depending on the low power laser therapy equipment, on the patient and on the anatomic area to be treated, the staff should adapt the recommended dosage for each individual case.

Development of Robotized Laser Welding Applications for Joining Thin Sheets

Laser Welding (LW) is more often used in manufacturing due to its advantages, such as accurate control, good repeatability, less heat input, opportunities for joining of special materials, high speed, capability to join small dimension parts etc. LW is dedicated to robotized manufacturing, and the fabrication cells are using various level of flexibility, from specialized robots to very flexible setups. This paper features several LW applications using two industrially-scaled manufacturing cells at UPM Laser Centre (CLUPM) of Polytechnical University of Madrid (Universidad Politécnica de Madrid). The one dedicated to Remote Laser Welding (RLW) of thin sheets for automotive and other sectors uses a CO2 laser of 3500 W. The second has a high flexibility, is based on a 6-axis ABB robot and a Nd:YAG laser of 3300 W, and is meant for various laser processing methods, including welding. After a short description of each cell, several LW applications experimented at CLUPM and recently implemented in industry are briefly presented: RLW of automotive coated sheets, LW of high strength automotive sheets, LW vs. laser hybrid welding (LHW) of Double Phase steel thin sheets, and LHW of thin sheets of stainless steel and carbon steel (dissimilar joints). The main technological issues overcame and the critical process parameters are pointed out. Conclusions about achievements and trends are provided.

Multimodal non-rigid image registration methods for therapy and surgery planning

La planificación pre-operatoria se ha convertido en una tarea esencial en cirugías y terapias de marcada complejidad, especialmente aquellas relacionadas con órgano blando. Un ejemplo donde la planificación preoperatoria tiene gran interés es la cirugía hepática. Dicha planificación comprende la detección e identificación precisa de las lesiones individuales y vasos así como la correcta segmentación y estimación volumétrica del hígado funcional. Este proceso es muy importante porque determina tanto si el paciente es un candidato adecuado para terapia quirúrgica como la definición del abordaje a seguir en el procedimiento. La radioterapia de órgano blando es un segundo ejemplo donde la planificación se requiere tanto para la radioterapia externa convencional como para la radioterapia intraoperatoria. La planificación comprende la segmentación de tumor y órganos vulnerables y la estimación de la dosimetría. La segmentación de hígado funcional y la estimación volumétrica para planificación de la cirugía se estiman habitualmente a partir de imágenes de tomografía computarizada (TC). De igual modo, en la planificación de radioterapia, los objetivos de la radiación se delinean normalmente sobre TC. Sin embargo, los avances en las tecnologías de imagen de resonancia magnética (RM) están ofreciendo progresivamente ventajas adicionales. Por ejemplo, se ha visto que el ratio de detección de metástasis hepáticas es significativamente superior en RM con contraste Gd–EOB–DTPA que en TC. Por tanto, recientes estudios han destacado la importancia de combinar la información de TC y RM para conseguir el mayor nivel posible de precisión en radioterapia y para facilitar una descripción precisa de las lesiones del hígado. Con el objetivo de mejorar la planificación preoperatoria en ambos escenarios se precisa claramente de un algoritmo de registro no rígido de imagen. Sin embargo, la gran mayoría de sistemas comerciales solo proporcionan métodos de registro rígido. Las medidas de intensidad de voxel han demostrado ser criterios de similitud de imágenes robustos, y, entre ellas, la Información Mutua (IM) es siempre la primera elegida en registros multimodales. Sin embargo, uno de los principales problemas de la IM es la ausencia de información espacial y la asunción de que las relaciones estadísticas entre las imágenes son homogéneas a lo largo de su domino completo. La hipótesis de esta tesis es que la incorporación de información espacial de órganos al proceso de registro puede mejorar la robustez y calidad del mismo, beneficiándose de la disponibilidad de las segmentaciones clínicas. En este trabajo, se propone y valida un esquema de registro multimodal no rígido 3D usando una nueva métrica llamada Información Mutua Centrada en el Órgano (Organ-Focused Mutual Information metric (OF-MI)) y se compara con la formulación clásica de la Información Mutua. Esto permite mejorar los resultados del registro en áreas problemáticas incorporando información regional al criterio de similitud, beneficiándose de la disponibilidad real de segmentaciones en protocolos estándares clínicos, y permitiendo que la dependencia estadística entre las dos modalidades de imagen difiera entre órganos o regiones. El método propuesto se ha aplicado al registro de TC y RM con contraste Gd–EOB–DTPA así como al registro de imágenes de TC y MR para planificación de radioterapia intraoperatoria rectal. Adicionalmente, se ha desarrollado un algoritmo de apoyo de segmentación 3D basado en Level-Sets para la incorporación de la información de órgano en el registro. El algoritmo de segmentación se ha diseñado específicamente para la estimación volumétrica de hígado sano funcional y ha demostrado un buen funcionamiento en un conjunto de imágenes de TC abdominales. Los resultados muestran una mejora estadísticamente significativa de OF-MI comparada con la Información Mutua clásica en las medidas de calidad de los registros; tanto con datos simulados (p<0.001) como con datos reales en registro hepático de TC y RM con contraste Gd– EOB–DTPA y en registro para planificación de radioterapia rectal usando OF-MI multi-órgano (p<0.05). Adicionalmente, OF-MI presenta resultados más estables con menor dispersión que la Información Mutua y un comportamiento más robusto con respecto a cambios en la relación señal-ruido y a la variación de parámetros. La métrica OF-MI propuesta en esta tesis presenta siempre igual o mayor precisión que la clásica Información Mutua y consecuentemente puede ser una muy buena alternativa en aplicaciones donde la robustez del método y la facilidad en la elección de parámetros sean particularmente importantes. Abstract Pre-operative planning has become an essential task in complex surgeries and therapies, especially for those affecting soft tissue. One example where soft tissue preoperative planning is of high interest is liver surgery. It involves the accurate detection and identification of individual liver lesions and vessels as well as the proper functional liver segmentation and volume estimation. This process is very important because it determines whether the patient is a suitable candidate for surgical therapy and the type of procedure. Soft tissue radiation therapy is a second example where planning is required for both conventional external and intraoperative radiotherapy. It involves the segmentation of the tumor target and vulnerable organs and the estimation of the planned dose. Functional liver segmentations and volume estimations for surgery planning are commonly estimated from computed tomography (CT) images. Similarly, in radiation therapy planning, targets to be irradiated and healthy and vulnerable tissues to be protected from irradiation are commonly delineated on CT scans. However, developments in magnetic resonance imaging (MRI) technology are progressively offering advantages. For instance, the hepatic metastasis detection rate has been found to be significantly higher in Gd–EOB–DTPAenhanced MRI than in CT. Therefore, recent studies highlight the importance of combining the information from CT and MRI to achieve the highest level of accuracy in radiotherapy and to facilitate accurate liver lesion description. In order to improve those two soft tissue pre operative planning scenarios, an accurate nonrigid image registration algorithm is clearly required. However, the vast majority of commercial systems only provide rigid registration. Voxel intensity measures have been shown to be robust measures of image similarity, and among them, Mutual Information (MI) is always the first candidate in multimodal registrations. However, one of the main drawbacks of Mutual Information is the absence of spatial information and the assumption that statistical relationships between images are the same over the whole domain of the image. The hypothesis of the present thesis is that incorporating spatial organ information into the registration process may improve the registration robustness and quality, taking advantage of the clinical segmentations availability. In this work, a multimodal nonrigid 3D registration framework using a new Organ- Focused Mutual Information metric (OF-MI) is proposed, validated and compared to the classical formulation of the Mutual Information (MI). It allows improving registration results in problematic areas by adding regional information into the similitude criterion taking advantage of actual segmentations availability in standard clinical protocols and allowing the statistical dependence between the two modalities differ among organs or regions. The proposed method is applied to CT and T1 weighted delayed Gd–EOB–DTPA-enhanced MRI registration as well as to register CT and MRI images in rectal intraoperative radiotherapy planning. Additionally, a 3D support segmentation algorithm based on Level-Sets has been developed for the incorporation of the organ information into the registration. The segmentation algorithm has been specifically designed for the healthy and functional liver volume estimation demonstrating good performance in a set of abdominal CT studies. Results show a statistical significant improvement of registration quality measures with OF-MI compared to MI with both simulated data (p<0.001) and real data in liver applications registering CT and Gd–EOB–DTPA-enhanced MRI and in registration for rectal radiotherapy planning using multi-organ OF-MI (p<0.05). Additionally, OF-MI presents more stable results with smaller dispersion than MI and a more robust behavior with respect to SNR changes and parameters variation. The proposed OF-MI always presents equal or better accuracy than the classical MI and consequently can be a very convenient alternative within applications where the robustness of the method and the facility to choose the parameters are particularly important.

Mechanical properties enhancement of high reliability metallic materials by laser shock processing

Laser shock processing (LSP) is being increasingly applied as an effective technology for the improvement of metallic materials surface properties in different types of components as a means of enhancement of their corrosion and fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, follow-on experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (especially Al and Ti alloys) under different LSP irradiation conditions are presented along with a practical correlated analysis on the protective character of the residual stress profiles obtained under different irradiation strategies and the evaluation of the corresponding induced properties as material specific volume reduction at the surface, microhardness and wear resistance. Additional remarks on the improved character of the LSP technique over the traditional “shot peening” technique in what concerns depth of induced compressive residual stresses fields are also made through the paper.

Light level to electrical frequency conversion with hybrid optical bistable devices.

A new concept in light level detection. The basis is the use of hybrid optical bistable devices working in oscillatory mode. The obtained instabilities show a correspondence between their frequency and the laser light intensity.

Bit noise from an optical logic gate with laser diodes

Output bits from an optical logic cell present noise due to the type of technique used to obtain the Boolean functions of two input data bits. We have simulated the behavior of an optically programmable logic cell working with Fabry Perot-laser diodes of the same type employed in optical communications (1550nm) but working here as amplifiers. We will report in this paper a study of the bit noise generated from the optical non-linearity process allowing the Boolean function operation of two optical input data signals. Two types of optical logic cells will be analyzed. Firstly, a classical "on-off" behavior, with transmission operation of LD amplifier and, secondly, a more complicated configuration with two LD amplifiers, one working on transmission and the other one in reflection mode. This last configuration has nonlinear behavior emulating SEED-like properties. In both cases, depending on the value of a "1" input data signals to be processed, a different logic function can be obtained. Also a CW signal, known as control signal, may be apply to fix the type of logic function. The signal to noise ratio will be analyzed for different parameters, as wavelength signals and the hysteresis cycles regions associated to the device, in relation with the signals power level applied. With this study we will try to obtain a better understanding of the possible effects present on an optical logic gate with Laser Diodes.

Effect of Thermal Treatments on the Mechanical Properties Enhancement of High Reliability Metallic Materials by Laser Shock Processing

Laser shock processing (LSP) is increasingly applied as an effective technology for the improvement of metallic materials mechanical properties in different types of components as a means of enhancement of their fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses fields into metallic components allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, experimental results on the residual stress profiles and associated mechanical properties modification successfully reached in typical materials under different LSP irradiation conditions are presented. In this case, the specific behavior of a widely used material in high reliability components (especially in nuclear and biomedical applications) as AISI 316L is analyzed, the effect of possible “in-service” thermal conditions on the relaxation of the LSP effects being specifically characterized. I.

Induction of engineered residual stresses fields and enhancement of fatigue life of high reliability metallic components by laser shock processing

Laser shock processing (LSP) is being increasingly applied as an effective technology for the improvement of metallic materials mechanical and surface properties in different types of components as a means of enhancement of their corrosion and fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view) are presented in this paper. Concretely, follow-on experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (especially Al and Ti alloys characteristic of high reliability components in the aerospace, nuclear and biomedical sectors) under different LSP irradiation conditions are presented along with a practical correlated analysis on the protective character of the residual stress profiles obtained under different irradiation strategies. Additional remarks on the improved character of the LSP technique over the traditional “shot peening” technique in what concerns depth of induced compressive residual stresses fields are also made through the paper

A method to obtain the thermal parameters and the photothermal transduction efficiency in an optical hyperthermia device based on laser irradiation of gold nanoparticles

Optical hyperthermia systems based on the laser irradiation of gold nanorods seem to be a promising tool in the development of therapies against cancer. After a proof of concept in which the authors demonstrated the efficiency of this kind of systems, a modeling process based on an equivalent thermal-electric circuit has been carried out to determine the thermal parameters of the system and an energy balance obtained from the time-dependent heating and cooling temperature curves of the irradiated samples in order to obtain the photothermal transduction efficiency. By knowing this parameter, it is possible to increase the effectiveness of the treatments, thanks to the possibility of predicting the response of the device depending on the working configuration. As an example, the thermal behavior of two different kinds of nanoparticles is compared. The results show that, under identical conditions, the use of PEGylated gold nanorods allows for a more efficient heating compared with bare nanorods, and therefore, it results in a more effective therapy.

Feasibility assessment of the interactive use of a Monte Carlo algorithm in treatment planning for intraoperative electron radiation therapy

This work analysed the feasibility of using a fast, customized Monte Carlo (MC) method to perform accurate computation of dose distributions during pre- and intraplanning of intraoperative electron radiation therapy (IOERT) procedures. The MC method that was implemented, which has been integrated into a specific innovative simulation and planning tool, is able to simulate the fate of thousands of particles per second, and it was the aim of this work to determine the level of interactivity that could be achieved. The planning workflow enabled calibration of the imaging and treatment equipment, as well as manipulation of the surgical frame and insertion of the protection shields around the organs at risk and other beam modifiers. In this way, the multidisciplinary team involved in IOERT has all the tools necessary to perform complex MC dosage simulations adapted to their equipment in an efficient and transparent way. To assess the accuracy and reliability of this MC technique, dose distributions for a monoenergetic source were compared with those obtained using a general-purpose software package used widely in medical physics applications. Once accuracy of the underlying simulator was confirmed, a clinical accelerator was modelled and experimental measurements in water were conducted. A comparison was made with the output from the simulator to identify the conditions under which accurate dose estimations could be obtained in less than 3 min, which is the threshold imposed to allow for interactive use of the tool in treatment planning. Finally, a clinically relevant scenario, namely early-stage breast cancer treatment, was simulated with pre- and intraoperative volumes to verify that it was feasible to use the MC tool intraoperatively and to adjust dose delivery based on the simulation output, without compromising accuracy. The workflow provided a satisfactory model of the treatment head and the imaging system, enabling proper configuration of the treatment planning system and providing good accuracy in the dosage simulation.

Effect of Thermal Treatments on the Mechanical Properties Enhancement of High Reliability Metallic Materials by Laser Shock Processing

Laser shock processing (LSP) is increasingly applied as an effective technology for the improvement of metallic materials mechanical properties in different types of components as a means of enhancement of their fatigue life behavior. As reported in previous contributions by the authors, a main effect resulting from the application of the LSP technique consists on the generation of relatively deep compression residual stresses fields into metallic components allowing an improved mechanical behaviour, explicitly the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Additional results accomplished by the authors in the line of practical development of the LSP technique at an experimental level (aiming its integral assessment from an interrelated theoretical and experimental point of view)are presented in this paper. Concretely, experimental results on the residual stress profiles and associated mechanical properties modification successfully reached in typical materials under different LSP irradiation conditions are presented. In this case, the specific behavior of a widely used material in high reliability components (especially in nuclear and biomedical applications) as AISI 316L is analyzed, the effect of possible “in-service” thermal conditions on the relaxation of the LSP effects being specifically characterized.

Contribución al estudio de propiedades ópticas en medios heterogéneos

Como contribución del estudio de medios heterogéneos, esta tesis recoge el trabajo llevado a cabo sobre modelado teórico y simulación del estudio de las propiedades ópticas de la piel y del agua del mar, como ejemplos paradigmáticos de medios heterogéneos. Se ha tomado como punto de partida el estudio de la propagación de la radiación óptica, más concretamente de la radiación láser, en un tejido biológico. La importancia de la caracterización óptica de un tejido es fundamental para manejar la interacción radiación-tejido que permite tanto el diagnóstico como la terapéutica de enfermedades y/o de disfunciones en las Ciencias de la Salud. Sin olvidar el objetivo de ofrecer una metodología de estudio, con un «enfoque ingenieril», de las propiedades ópticas en un medio heterogéneo, que no tiene por qué ser exclusivamente el tejido biológico. Como consecuencia de lo anterior y de la importancia que tiene el agua dentro de los tejidos biológicos se decide estudiar en otro capítulo las propiedades ópticas del agua dentro de un entorno heterogéneo como es el agua del mar. La selección del agua del mar, como objeto de estudio adicional, es motivada, principalmente, porque se trata de un sistema heterogéneo fácilmente descriptible en cada uno de sus elementos y permite evaluar una amplia bibliografía. Además se considera que los avances que han tenido lugar en los últimos años en las tecnologías fotónicas van a permitir su uso en los métodos experimentales de análisis de las aguas. El conocimiento de sus propiedades ópticas permite caracterizar los diferentes tipos de aguas de acuerdo con sus compuestos, así como poder identificar su presencia. Todo ello abre un amplio abanico de aplicaciones. En esta tesis doctoral, se ha conseguido de manera general: • Realizar un estudio del estado del arte del conocimiento de las propiedades ópticas de la piel y la identificación de sus elementos dispersores de la luz. • Establecer una metodología de estudio que nos permita obtener datos sobre posibles efectos de la radiación en los tejidos biológicos. •Usar distintas herramientas informáticas para simular el transporte de la radiación laser en tejidos biológicos. • Realizar experimentos mediante simulación de láser, tejidos biológicos y detectores. • Comparar los resultados conocidos experimentalmente con los simulados. • Estudiar los instrumentos de medida de la respuesta a la propagación de radiación laser en tejidos anisotrópicos. • Obtener resultados originales para el diagnóstico y tratamiento de pieles, considerando diferente razas y como alteración posible en la piel, se ha estudiado la presencia del basalioma. • Aplicación de la metodología de estudio realizada en la piel a la simulación de agua de mar. • Obtener resultados originales de simulación y análisis de cantidad de fitoplancton en agua; con el objetivo de facilitar la caracterización de diferentes tipos de aguas. La tesis doctoral se articula en 6 capítulos y 3 anexos perfectamente diferenciados con su propia bibliografía en cada uno de ellos. El primer capítulo está centrado en la problemática del difícil estudio y caracterización de los medios heterogéneos debidos a su comportamiento no homogéneo y anisotrópico ante las radiaciones ópticas. Así pues, presentaremos una breve introducción al comportamiento tanto de los tejidos como del océano ante radiaciones ópticas y definiremos sus principales propiedades: la absorción, el scattering, la anisotropía y los coeficientes de reflexión. Como continuación, un segundo capítulo trata de acercarnos a la resolución del problema de cómo caracterizar las propiedades ópticas descritas en el primer capítulo. Para ello, primero se introducen los modelos teóricos, en segundo lugar los métodos de simulación más empleados y, por último, enumerar las principales técnicas de medida de la propagación de la luz en los tejidos vivos. El tercer capítulo, centrado en la piel y sus propiedades, intenta realizar una síntesis de lo que se conoce sobre el comportamiento de la piel frente a la propagación de las radiaciones ópticas. Se estudian sus elementos constituyentes y los distintos tipos de pieles. Por último se describe un ejemplo de aplicación más inmediata que se beneficia de este conocimiento. Sabemos que el porcentaje de agua en el cuerpo humano es muy elevado, en concreto en la piel se considera de aproximadamente un 70%. Es obvio, por tanto, que conocer cómo afecta el agua en la propagación de una radiación óptica facilitaría el disponer de patrones de referencia; para ello, se realiza el estudio del agua del mar. En el cuarto capítulo se estudian las propiedades del agua del mar como medio heterogéneo de partículas. En este capítulo presentamos una síntesis de los elementos más significativos de dispersores en el océano, un estudio de su comportamiento individual frente a radiaciones ópticas y su contribución al océano en su conjunto. Finalmente, en el quinto capítulo se describen los resultados obtenidos en los distintos tipos de simulaciones realizadas. Las herramientas de simulación empleadas han sido las mismas tanto para el caso del estudio de la piel como para el agua del mar, por ello ambos resultados son expuestos en el mismo capítulo. En el primer caso se analizan diferentes tipos de agua oceánica, mediante la variación de las concentraciones de fitoplancton. El método empleado permite comprobar las diferencias que pueden encontrarse en la caracterización y diagnóstico de aguas. El segundo caso analizado es el de la piel; donde se estudia el comportamiento de distintos tipos de piel, se analizan para validar el método y se comprueba cómo el resultado es compatible con aplicaciones, actualmente comerciales, como la de la depilación con láser. Como resultado significativo se muestra la posible metodología a aplicar para el diagnóstico del cáncer de piel conocido como basalioma. Finalmente presentamos un capítulo dedicado a los trabajos futuros basados en experimentación real y el coste asociado que implicaría el llevarlo a cabo. Los anexos que concluyen la tesis doctoral versan por un lado sobre el funcionamiento del vector común de toda la tesis: el láser, sus aplicaciones y su control en la seguridad y por otro presentamos los coeficientes de absorción y scattering que hemos utilizado en nuestras simulaciones. El primero condensa las principales características de una radiación láser desde el punto de vista de su generación, el segundo presenta la seguridad en su uso y el tercero son tablas propias, cuyos parámetros son los utilizados en el apartado de experimentación. Aunque por el tipo de tesis que defiendo no se ajusta a los modelos canónicos de tesis doctoral, el lector podrá encontrar en esta tesis de forma imbricada, el modelo común a todas las tesis o proyectos de investigación con una sección dedicada al estado del arte con ejemplos pedagógicos para facilitar la compresión y se plantean unos objetivos (capítulos 1-4), y un capítulo que se subdivide en materiales y métodos y resultados y discusiones (capítulo 5 con sus subsecciones), para finalizar con una vista al futuro y los trabajos futuros que se desprenden de la tesis (capítulo 6). ABSTRACT As contribution to the study of heterogeneous media, this thesis covers the work carried out on theoretical modelling and simulation study of the optical properties of the skin and seawater, as paradigmatic examples of heterogeneous media. It is taken as a starting point the study of the propagation of optical radiation, in particular laser radiation in a biological tissue. The importance of optical characterization of a tissue is critical for managing the interaction between radiation and tissues that allows both diagnosis and therapy of diseases and / or dysfunctions in Health Sciences. Without forgetting the aim of providing a methodology of study, with "engineering approach" of the optical properties in a heterogeneous environment, which does not have to be exclusively biological tissue. As a result of this and the importance of water in biological tissues, we have decided to study the optical properties of water in a heterogeneous environment such as seawater in another chapter. The selection of sea water as an object of further study is motivated mainly because it is considered that the advances that have taken place in recent years in photonic technologies will allow its use in experimental methods of water analysis. Knowledge of the optical properties to characterize the different types of waters according to their compounds, as well as to identify its presence. All of this opens a wide range of applications. In this thesis, it has been generally achieved: • Conduct a study of the state of the art knowledge of the optical properties of the skin and identifying its light scattering elements. • Establish a study methodology that allows us to obtain data on possible effects of radiation on biological tissues. • Use different computer tools to simulate the transport of laser radiation in biological tissues. • Conduct experiments by simulating: laser, detectors, and biological tissues. • Compare the known results with our experimentally simulation. • Study the measuring instruments and its response to the propagation of laser radiation in anisotropic tissues. • Get innovative results for diagnosis and treatment of skin, considering different races and a possible alteration in the skin that we studied: the presence of basal cell carcinoma. • Application of the methodology of the study conducted in the skin to simulate seawater. • Get innovative results of simulation and analysis of amount of phytoplankton in water; in order to facilitate the characterization of different types of water. The dissertation is divided into six chapters and three annexes clearly distinguished by their own literature in each of them. The first chapter is focused on the problem of difficult study and characterization of heterogeneous media due to their inhomogeneous and anisotropic behaviour of optical radiation. So we present a brief introduction to the behaviour of both tissues at the cellular level as the ocean, to optical radiation and define the main optical properties: absorption, scattering, anisotropy and reflection coefficients. Following from this, a second chapter is an approach to solving the problem of how to characterize the optical properties described in the first chapter. For this, first the theoretical models are introduced, secondly simulation methods more used and, finally, the main techniques for measuring the propagation of light in living tissue. The third chapter is focused on the skin and its properties, tries to make a synthesis of what is known about the behaviour of the skin and its constituents tackle the spread of optical radiation. Different skin types are studied and an example of immediate application of this knowledge benefits described. We know that the percentage of water in the human body is very high, particularly in the skin is considered about 70%. It is obvious, therefore, that knowing how the water is affected by the propagation of an optical radiation facilitate to get reference patterns; For this, the study of seawater is performed. In the fourth chapter the properties of seawater as a heterogeneous component particles are studied. This chapter presents a summary of the scattering elements in the ocean, its individual response to optical radiation and its contribution to the ocean as a whole. In the fifth chapter the results of the different types of simulations are described. Simulation tools used were the same for the study of skin and seawater, so both results are presented in the chapter. In the first case different types of ocean water is analysed by varying the concentrations of phytoplankton. The method allows to check the differences that can be found in the characterization and diagnosis of water. The second case analysed is the skin; where the behaviour of different skin types are studied and checked how the result is compatible with applications currently trade, such as laser hair removal. As a significant result of the possible methodology to be applied for the diagnosis of skin cancer known as basal cell carcinoma is shown. Finally we present a chapter on future work based on actual experimentation and the associated cost which it would involve carrying out. The annexes conclude the thesis deal with one hand on the functioning of the common vector of the whole thesis: laser, control applications and safety and secondly we present the absorption and scattering coefficients we used in our simulations. The first condenses the main characteristics of laser radiation from the point of view of their generation, the second presents the safety in use and the third are own tables, whose parameters are used in the experimental section. Although the kind of view which I advocate does not meet the standard models doctoral thesis, the reader will find in this thesis so interwoven, the common model to all theses or research projects with a section on the state of the art pedagogical examples to facilitate the understanding and objectives (Chapters 1-4), and a chapter is divided into materials and methods and results and discussions (Chapter 5 subsections) arise, finishing with a view to the future and work future arising from the thesis (Chapter 6).