Raman and infrared spectra of dimethyl ether 13C-isotopologue (CH3O13CH3) from a CCSD(T) potential energy surface

So far, no experimental data of the infrared and Raman spectra of 13C isotopologue of dimethyl ether are available. With the aim of providing some clues of its low-lying vibrational bands and with the hope of contributing in a next spectral analysis, a number of vibrational transition frequencies below 300 cm−1 of the infrared spectrum and around 400 cm−1 of the Raman spectrum have been predicted and their assignments were proposed. Calculations were carried out through an ab initio three dimensional potential energy surface based on a previously reported one for the most abundant dimethyl ether isotopologue (M. Villa et al., J. Phys. Chem. A 115 (2011) 13573). The potential function was vibrationally corrected and computed with a highly correlated CCSD(T) method involving the COC bending angle and the two large amplitude CH3 internal rotation degrees of freedom. Also, the Hamiltonian parameters could represent a support for the spectral characterization of this species. Although the computed vibrational term values are expected to be very accurate, an empirical adjustment of the Hamiltonian has been performed with the purpose of anticipating some workable corrections to any possible divergence of the vibrational frequencies. Also, the symmetry breaking derived from the isotopic substitution of 13C in the dimethyl ether was taken into account when the symmetrization procedure was applied.

Hysteresis phenomena in transverse galloping of triangular cross-section bodies

Transverse galloping is a type of aeroelastic instability characterised by large amplitude, low frequency oscillation of a structure in the direction normal to the mean wind direction. It normally appears in bodies with small stiffness and structural damping, provided the incident flow velocity is high enough. In the simplest approach transverse galloping can be considered as a one-degree-of-freedom oscillator subjected to aerodynamic forces, which in turn can be described by using a quasi-steady description. In this frame it has been demonstrated that hysteresis phenomena in transverse galloping is related to the existence of inflection points in the curve giving the dependence with the angle of attack of the aerodynamic coefficient normal to the incident flow. Aiming at experimentally checking such a relationship between these inflection points and hysteresis, wind tunnel experiments have been conducted. Experiments have been restricted to isosceles triangular cross-section bodies, whose galloping behaviour is well documented. Experimental results show that, according to theoretical predictions, hysteresis takes place at the angles of attack where there are inflection points in the lift coefficient curve, provided that the body is prone to gallop at these angles of attack.

Fenómenos de galope en piezas prismáticas con sección en H

El objetivo de esta Tesis es el estudio sistemático del fenómeno aeroelástico de galope de una viga prismática con sección transversal en H. En particular, se pretende analizar la influencia de determinados parámetros geométricos que definen la geometría de la sección y el efecto del ángulo de ataque de la corriente sobre la estabilidad del fenómeno de oscilación. El interés en el estudio de esta forma de la sección transversal de una viga se basa en el hecho de que, con cierta frecuencia, se sigue utilizando, por su buen comportamiento estructural, en construcciones civiles como tableros y tirantes de puentes de gran longitud, señalizaciones, luminarias y, en general, en grandes estructuras metálicas. Los parámetros geométricos seleccionados para su estudio son tres: el espesor de las dos alas verticales, su porosidad y el espesor de sendas ranuras en la zona de unión entre el alma y las alas de la sección. Inicialmente se han realizado ensayos estáticos en un túnel aerodinámico con objeto de obtener las cargas aerodinámicas y poder aplicar el criterio casi-estático de Glauert - Den Hartog. En estos ensayos, se han medido tanto las fuerzas de sustentación y resistencia aerodinámicas como las distribuciones de presiones en la superficie de la zona central de la sección. Posteriormente, se han realizado ensayos de visualización de flujo, utilizando un túnel de humos, para poder comprender mejor el comportamiento físico del aire alrededor del cuerpo. El estudio estático se ha completado realizando ensayos con PIV, que permiten realizar una medida precisa de la velocidad del campo fluido. Por último, se han realizado ensayos dinámicos en otro túnel aerodinámico con objeto de contrastar la aplicabilidad del criterio casi-estático, la velocidad de inicio de galope y la amplitud de las oscilaciones producidas. Los resultados muestran que el espesor de las alas verticales, aunque modifica apreciablemente la magnitud de las cargas aerodinámicas, no afecta sustancialmente a la estabilidad a galope, mientras que su porosidad sí ejerce un control efectivo que permite reducir este fenómeno e incluso evitarlo, en determinados casos. En todas las situaciones el criterio de Glauert-Glauert - Den Hartog ha resultado ser aplicable y, en ocasiones, más restrictivo que los resultados obtenidos en ensayos dinámicos. La presencia de una ranura en la zona de unión entre el alma y las dos alas, o su combinación con la porosidad en las alas, reduce la intensidad de galope, incrementando la velocidad crítica de su inicio, pero no logra hacer que desaparezca, como se justificará en el desarrollo del trabajo. ABSTRACT Galloping is a type of aeroelastic instability characterized by a large amplitude oscillation at the natural frequency of the structure, producing normal motion to wind. It usually occurs in slender bodies lightly damped at sufficiently high speeds. In this thesis an experimental study has been developed on the galloping instability of a beam with H cross section, which is inscribed in a rectangle with a slender 1: 2. A systematic study has been carried out of the influence of three different geometric parameters on galloping, in the range of 0 to 90° angle of attack of the incoming stream. These parameters are the thickness of the flanges of the section, the porosity of the flanges, the thickness of two slots along the span, in the area between the flange and the central core of the section, and the combination effect of the last two parameters. First of all, static tests have been performed in a wind tunnel to determine the lift and drag forces by using a balance and then the quasi-static stability criterion due to Glauert-Den Hartog has been determined. Later, to better understand and verify the results previously obtained, it has also been tested the pressure distribution on the surface of the model, flow visualization in a second, smoke, wind tunnel, and Particle Image Velocimetry (PIV) study of the flow around the section, in a third tunnel. Finally, dynamic tests have been performed, on a fourth wind tunnel, for determining the amplitude and frequency of the oscillations in each case. The results have been collected in stability diagrams for each geometric parameter studied. These results show that the more critical angles of attack of the stream for galloping behavior are close to 0 and 90º. It has been found that the thickness of the flanges, although changes the galloping behavior on the section, does not reduce it substantially. However, the porosity in the flanges has been proved to be an efficient control mechanism on galloping, and even above 40% porosity, it disappears. The thickness of the slot studied and its combination with the porosity in the flanges in some cases reduces the aerodynamic forces appreciably but fail to prevent galloping at all angles of attack.

Transverse galloping of two-dimensional bodies having a rhombic cross-section

Transverse galloping is a type of aeroelastic instability characterized by oscillations perpendicular to wind direction, large amplitude and low frequency, which appears in some elastic two-dimensional bluff bodies when they are subjected to an incident flow, provided that the flow velocity exceeds a threshold critical value. Understanding the galloping phenomenon of different cross-sectional geometries is important in a number of engineering applications: for energy harvesting applications the interest relies on strongly unstable configurations but in other cases the purpose is to avoid this type of aeroelastic phenomenon. In this paper the aim is to analyze the transverse galloping behavior of rhombic bodies to understand, on the one hand, the dependence of the instability with a geometrical parameter such as the relative thickness and, on the other hand, why this cross-section shape, that is generally unstable, shows a small range of relative thickness values where it is stable. Particularly, the non-galloping rhombus-shaped prism?s behavior is revised through wind tunnel experiments. The bodies are allowed to freely move perpendicularly to the incoming flow and the amplitude of movement and pressure distributions on the surfaces is measured.

Determination of Maximum Mechanical Energy Efficiency in Energy Galloping Systems

Transverse galloping is a type of aeroelastic instability characterized by large amplitude, low frequency, normal to wind oscillations that appear in some elastic two-dimensional bluff bodies when subjected to a fluid flow, provided that the flow velocity exceeds a threshold critical value. Such an oscillatory motion is explained because of the energy transfer from the flow to the two-dimensional bluff body. The 7 amount of energy that can be extracted depends on the cross section of the galloping prism. Assuming that the Glauert-Den Hartog quasistatic criterion for galloping instability is satisfied in a first approximation, the suitability of a given cross section for energy harvesting is evaluated by analyzing the lateral aerodynamic force coefficient, fitting a function with a power series in tan a (a being the angle of attack) to 10 available experimental data. In this paper, a fairly large number of simple prisms (triangle, ellipse, biconvex, and rhombus cross sections, as well 11 as D-shaped bodies) is analyzed for suitability as energy harvesters. The influence of the fitting process in the energy harvesting efficiency evaluation is also demonstrated. The analysis shows that the more promising bodies are those with isosceles or approximate isosceles cross sections.

Dynamics of gas bubbles encapsulated by a viscoelastic fluid shell under acoustic fields

The dynamics of a gas-filled microbubble encapsulated by a viscoelastic fluid shell immersed in a Newtonian liquid and subject to an external pressure field is theoretically studied. The problem is formulated by considering a nonlinear Oldroyd type constitutive equation to model the rheological behavior of the fluid shell. Heat and mass transfer across the surface bubble have been neglected but radiation losses due to the compressibility of the surrounding liquid have been taken into account. Bubble collapse under sudden increase of the external pressure as well as nonlinear radial oscillations under ultrasound fields are investigated. The numerical results obtained show that the elasticity of the fluid coating intensifies oscillatory collapse and produces a strong increase of the amplitudes of radial oscillations which may become chaotic even for moderate driving pressure amplitudes. The role played by the elongational viscosity has also been analyzed and its influence on both, bubble collapse and radial oscillations, has been recognized. According to the theoretical predictions provided in the present work, a microbubble coated by a viscoelastic fluid shell is an oscillating system that, under acoustic driving, may experience volume oscillations of large amplitude, being, however, more stable than a free bubble. Thus, it could be expected that such a system may have a suitable behavior as an echogenic agent.

Asymptotic Description of Flutter Amplitude Saturation by Nonlinear Friction Forces

The computation of the non-linear vibration dynamics of an aerodynamically unstable bladed-disk is a formidable numerical task, even for the simplified case of aerodynamic forces assumed to be linear. The nonlinear friction forces effectively couple dif- ferent travelling waves modes and, in order to properly elucidate the dynamics of the system, large time simulations are typically required to reach a final, saturated state. Despite of all the above complications, the output of the system (in the friction microslip regime) is basically a superposition of the linear aeroelastic un- stable travelling waves, which exhibit a slow time modulation that is much longer than the elastic oscillation period. This slow time modulation is due to both, the small aerodynamic effects and the small nonlinear friction forces, and it is crucial to deter- mine the final amplitude of the flutter vibration. In this presenta- tion we apply asymptotic techniques to obtain a new simplified model that captures the slow time dynamics of the amplitudes of the travelling waves. The resulting asymptotic model is very re- duced and extremely cheap to simulate, and it has the advantage that it gives precise information about the characteristics of the nonlinear friction models that actually play a role in the satura- tion of the vibration amplitude.

Asymptotic Description of Flutter Amplitude Saturation by Nonlinear Friction Forces

The computation of the non-linear vibration dynamics of an aerodynamically unstable bladed-disk is a formidable numerical task, even for the simplified case of aerodynamic forces assumed to be linear. The nonlinear friction forces effectively couple dif- ferent travelling waves modes and, in order to properly elucidate the dynamics of the system, large time simulations are typically required to reach a final, saturated state. Despite of all the above complications, the output of the system (in the friction microslip regime) is basically a superposition of the linear aeroelastic un- stable travelling waves, which exhibit a slow time modulation that is much longer than the elastic oscillation period. This slow time modulation is due to both, the small aerodynamic effects and the small nonlinear friction forces, and it is crucial to deter- mine the final amplitude of the flutter vibration. In this presenta- tion we apply asymptotic techniques to obtain a new simplified model that captures the slow time dynamics of the amplitudes of the travelling waves. The resulting asymptotic model is very re- duced and extremely cheap to simulate, and it has the advantage that it gives precise information about the characteristics of the nonlinear friction models that actually play a role in the satura- tion of the vibration amplitude.

A Wireless Charging System Applying Phase-Shift and Amplitude Control to Maximize Efficiency and Extractable Power

Wireless power transfer (WPT) is an emerging technology with an increasing number of potential applications to transfer power from a transmitter to a mobile receiver over a relatively large air gap. However, its widespread application is hampered due to the relatively low efficiency of current Wireless power transfer (WPT) systems. This study presents a concept to maximize the efficiency as well as to increase the amount of extractable power of a WPT system operating in nonresonant operation. The proposed method is based on actively modifying the equivalent secondary-side load impedance by controlling the phase-shift of the active rectifier and its output voltage level. The presented hardware prototype represents a complete wireless charging system, including a dc-dc converter which is used to charge a battery at the output of the system. Experimental results are shown for the proposed concept in comparison to a conventional synchronous rectification approach. The presented optimization method clearly outperforms state-of-the-art solutions in terms of efficiency and extractable power.