Particle filtering for indoor RFID tag tracking

In this paper, we propose a particle filtering (PF) method for indoor tracking using radio frequency identification (RFID) based on aggregated binary measurements. We use an Ultra High Frequency (UHF) RFID system that is composed of a standard RFID reader, a large set of standard passive tags whose locations are known, and a newly designed, special semi-passive tag attached to an object that is tracked. This semi-passive tag has the dual ability to sense the backscatter communication between the reader and other passive tags which are in its proximity and to communicate this sensed information to the reader using backscatter modulation. We refer to this tag as a sense-a-tag (ST). Thus, the ST can provide the reader with information that can be used to determine the kinematic parameters of the object on which the ST is attached. We demonstrate the performance of the method with data obtained in a laboratory environment.

Characterization cement pastes degraded in lanoratory solutions and physiochemical parameters employed for modeling the process

Previously degradation studies carried out, over a number of different mortars by the research team, have shown that observed degradation does not exclusively depend on the solution equilibrium pH, nor the aggressive anions relative solubility. In our tests no reason was found that could allow us to explain, why same solubility anions with a lower pH are less aggressive than others. The aim of this paper is to study cement pastes behavior in aggressive environments. As observed in previous research, this cement pastes behaviors are not easily explained only taking into account only usual parameters, pH, solubility etc. Consequently the paper is about studying if solution physicochemical characteristics are more important in certain environments than specific pH values. The paper tries to obtain a degradation model, which starting from solution physicochemical parameters allows us to interpret the different behaviors shown by different composition cements. To that end, the rates of degradation of the solid phases were computed for each considered environment. Three cement have been studied: CEM I 42.5R/SR, CEM II/A-V 42.5R and CEM IV/B-(P-V) 32.5 N. The pastes have been exposed to five environments: sodium acetate/acetic acid 0.35 M, sodium sulfate solution 0.17 M, a solution representing natural water, saturated calcium hydroxide solution and laboratory environment. The attack mechanism was meant to be unidirectional, in order to achieve so; all sides of cylinders were sealed except from the attacked surface. The cylinders were taking out of the exposition environments after 2, 4, 7, 14, 30, 58 and 90 days. Both aggressive solution variations in solid phases and in different depths have been characterized. To each age and depth the calcium, magnesium and iron contents have been analyzed. Hydrated phases evolution studied, using thermal analysis, and crystalline compound changes, using X ray diffraction have been also analyzed. Sodium sulphate and water solutions stabilize an outer pH near to 8 in short time, however the stability of the most pH dependent phases is not the same. Although having similar pH and existing the possibility of forming a plaster layer near to the calcium leaching surface, this stability is greater than other sulphate solutions. Stability variations of solids formed by inverse diffusion, determine the rate of degradation.

Implementación y análisis de luminarias LED

En este proyecto se abordan el diseño y análisis, con sus diferentes etapas, de varias configuraciones de prototipos para luminarias LED enfocadas al ámbito domestico e industrial. Se realizarán montajes sobre diferentes materiales para evaluar los resultados y decidir que soporte es más adecuado para cada circunstancia. Inicialmente expondremos el estado actual de esta tecnología y caracterizaremos, de forma preliminar, los dispositivos que vamos a utilizar para elaborar los prototipos que posteriormente analizaremos. Seguidamente detallaremos el proceso de construcción de cada prototipo, indicando especialmente las diferencias y similitudes entre ellos que, en siguientes secciones, serán analizadas. Trabajaremos con dos rangos de potencia para las luminarias. El primero de ellos se centra en obtener la máxima potencia lumínica, con valores comprendidos entre 40W y 50W, considerando un uso industrial, alumbrado público, etc. El segundo rango de potencias, se enfocará al ámbito doméstico, adecuando la temperatura de color a este entorno, para combinar la potencia, de entre 9W y 12W, con una iluminación más cálida. Finalmente someteremos los prototipos elaborados a una serie de análisis y, ante los resultados, concluiremos cuales serán aptos para el uso al que se pretenden dedicar y aquellos que deberán ser modificados. En el entorno de laboratorio, donde se llevaran a cabo análisis térmicos, eléctricos y lumínicos, emplearemos instrumental especializado para cada tipo de análisis así como su software correspondiente. A excepción de las mediciones relacionadas con el espectro de radiación lumínica, el resto serán obtenidas mediante la plataforma LabVIEW®, un completo software grafico para el desarrollo de instrumentación virtual. Como sección final, expondremos una evaluación sobre el cumplimiento de los objetivos establecidos para el proyecto, posibles mejoras o trabajos futuros y conclusiones obtenidas. ABSTRACT. This project concerns the design and analysis, with its different stages, of various configurations of LED luminaries prototypes focused on domestic and industrial environments. Mounts on different materials will be made to evaluate the results and decide which material is most appropriate for each circumstance. Initially we will expose the current state of this technology and characterize, in a preliminary way, the devices that we will use to produce the prototypes which subsequently will analyze. Later we detail the process of construction of each prototype, especially indicating the differences and similarities between them. In the following sections, we will analyze these characteristics. We will work with two power ranges for luminaries. The first one focuses on maximum light output, with values between 40W and 50W, thinking about industrial use, street lighting, etc. The second power range will focus on the domestic environment, adjusting the color temperature in this environment to combine power, between 9W and 12W, with warm lighting. Finally the prototypes will submit a series of analyzes and, with the results obtained, we conclude if will be suitable for the intended use and those that should be modified. In laboratory environment, where thermal, electrical and lighting analyzes were carried out, we will use specialized instruments for each type of analysis as well as the corresponding software. Except for measurements related to the spectrum of light radiation, the rest of information will be obtained by LabVIEW®, complete graphical development software for virtual instrumentation. As a final section, we will present an evaluation of compliance with the project objectives, possible future work, or improvements, and conclusions.

Water seepage beneath dams on soluble evaporite deposits: a laboratory and field study (Caspe Dam, Spain)

The paper presents analytical methods and results for assessing the variation in the concentration of sulphate (and other ions) over space and time in groundwater flowing through a soluble evaporite terrain beneath a dam. The influence of effective porosity, groundwater flow velocity and the specific rate of dissolution (K′) are considered. The theoretical analysis was tested in a scale model simulating a dam constructed on heavily karstified bedrock. A simple and useful method for assessing how much material is lost through dissolution and how the rate of dissolution changes over time is considered in the context of the Caspe Dam, Spain.

Neutron field characteristics of Ciemat's Neutron Standards Laboratory Hector Rene Vega-Carrillo

Monte Carlo calculations were carried out to characterize the neutron field produced by the calibration neutron sources of the Neutron Standards Laboratory at the Research Center for Energy, Environment and Technology (CIEMAT) in Spain. For 241AmBe and 252Cf neutron sources, the neutron spectra, the ambient dose equivalent rates and the total neutron fluence rates were estimated. In the calibration hall, there are several items that modify the neutron field. To evaluate their effects different cases were used, from point-like source in vacuum up to the full model. Additionally, using the full model, the neutron spectra were estimated to different distances along the bench; with these spectra, the total neutron fluence and the ambient dose equivalent rates were calculated. The hall walls induce the largest changes in the neutron spectra and the respective integral quantities. The free-field neutron spectrum is modified due the room return effect.