Comparison of natural and forced amplification regimes in plasma-based soft-x-ray lasers seeded by high-order harmonic

The amplification of high-order harmonics (HOH) in a plasma-based amplifier is a multiscale, temporal phenomenon that couples plasma hydrodynamics, atomic processes, and HOH electromagnetic fields. We use a one-dimensional, time-dependent Maxwell-Bloch code to compare the natural amplification regime and another regime where plasma polarization is constantly forced by the HOH. In this regime, a 10-MW (i.e., 100 times higher than current seeded soft x-ray laser power), 1.5-μJ, 140-fs pulse free from the parasitic temporal structures appearing on the natural amplification regime can be obtained.

Comparison of experimental and numerical sloshing loads in partially filled tanks

Sloshing describes the movement of liquids inside partially filled tanks, generating dynamic loads on the tank structure. The resulting impact pressures are of great importance in assessing structural strength, and their correct evaluation still represents a challenge for the designer due to the high level of nonlinearities involved, with complex free surface deformations, violent impact phenomena and influence of air trapping. In the present paper, a set of two-dimensional cases, for which experimental results are available, is considered to assess the merits and shortcomings of different numerical methods for sloshing evaluation, namely two commercial RANS solvers (FLOW-3D and LS-DYNA), and two academic software (Smoothed Particle Hydrodynamics and RANS). Impact pressures at various critical locations and global moment induced by water motion in a partially filled rectangular tank, subject to a simple harmonic rolling motion, are evaluated and predictions are compared with experimental measurements. 2012 Copyright Taylor and Francis Group, LLC.

Comparison of vibration and rolling noise emission of resilient and solid monobloc railway wheels in underground lines

Flat or worn wheels rolling on rough or corrugated tracks can provoke airborne noise and ground-borne vibration, which can be a serious concern for nearby neighbours of urban rail transit lines. Among the various treatments used to reduce vibration and noise, resilient wheels play an important role. In conventional resilient wheels, a slightly prestressed V­shaped rubber ring is mounted between the steel wheel centre and tyre. The elastic layer enhances rolling noise and vibration suppression, as well as impact reduction on the track. In this paper the effectiveness of resilient wheels in underground lines, in comparison to monobloc ones, is assessed. The analysed resilient wheel is able to carry greater loads than standard resilient wheels used for light vehicles. It also presents a greater radial resiliency and a higher axial stiffness than conventional V­wheels. The finite element method was used in this study. A quarter car model was defined, in which the wheelset was modelled as an elastic body. Several simulations were performed in order to assess the vibrational behaviour of elastic wheels, including modal, harmonic and random vibration analysis, the latter allowing the introduction of realistic vertical track irregularities, as well as the influence of the running speed. Due to numerical problems some simplifications were needed. Parametric variations were also performed, in which the sensitivity of the whole system to variations of rubber prestress and Poisson’s ratio of the elastic material was assessed.Results are presented in the frequency domain, showing a better performance of the resilient wheels for frequencies over 200 Hz. This result reveals the ability of the analyzed design to mitigate rolling noise, but not structural vibrations, which are primarily found in the lower frequency range.

Experimental comparison of FBARs and SMRs responsitivities to mass loadings

The utilisation of thin film technology to develop film bulk acoustic resonators (FBARs) and solidly mounted resonators (SMRs), offers great potential to outperform the sensitivity and minimum detection limit of gravimetric sensors. Up to now, the choice between FBARs and SMRs depends primarily on the users' ability to design and fabricate Bragg reflectors and/or membranes, because neither of these two types of resonators has been demonstrated to be superior to the other. In the work reported here, it is shown that identically designed FBARs and SMRs resonating at the same frequency exhibit different responsitivities, Rm, to mass loadings, being the FBARs more responsive than the SMRs. For the specific device design and resonant frequency (~2 GHz) of the resonators presented, FBARs' mass responsitivity is ~20% greater than that of SMRs, and although this value should not be taken as universal for all possible device designs, it clearly indicates that FBAR devices should be favoured over SMRs in gravimetric sensing applications.

Electron temperature versus laser intensity times wavelength squared: a comparison of theory and experiments

The peak temperature in the corona of plasma ejected by a laser-irradiated slab is discussed in terms of a one-electron-temperature model. Both heat-flux saturation and pulse rise-time effects are considered;the intensity in the rising half of the pulse is approximated by a linear function of time, I(t) = Iot/r. The temperature is found to be proportional to (IQX2)273 and a function of I0X4/r. Above a certain value of I0X4/T, the plasma presents two characteristic temperatures (at saturation and at the critical surface) which can be identified with experimentally observed cold- and hot-electron temperatures. The results are compared with extensive experimental data available for both nd and CO2 lasers, I0(W'cnf2) X2 (/um) starting around 1012. The agreement is good if substantial flux inhibition is assumed (flux-limit factor f = 0.03), and fails for I0X2 above 1O1S. Results for both ablation pressure and mass ablation rate are also given.

A new PET prototype for proton therapy: comparison of data and Monte Carlo simulations

Ion beam therapy is a valuable method for the treatment of deep-seated and radio-resistant tumors thanks to the favorable depth-dose distribution characterized by the Bragg peak. Hadrontherapy facilities take advantage of the specific ion range, resulting in a highly conformal dose in the target volume, while the dose in critical organs is reduced as compared to photon therapy. The necessity to monitor the delivery precision, i.e. the ion range, is unquestionable, thus different approaches have been investigated, such as the detection of prompt photons or annihilation photons of positron emitter nuclei created during the therapeutic treatment. Based on the measurement of the induced β+ activity, our group has developed various in-beam PET prototypes: the one under test is composed by two planar detector heads, each one consisting of four modules with a total active area of 10 × 10 cm2. A single detector module is made of a LYSO crystal matrix coupled to a position sensitive photomultiplier and is read-out by dedicated frontend electronics. A preliminary data taking was performed at the Italian National Centre for Oncological Hadron Therapy (CNAO, Pavia), using proton beams in the energy range of 93–112 MeV impinging on a plastic phantom. The measured activity profiles are presented and compared with the simulated ones based on the Monte Carlo FLUKA package.

Measuring skin temperature before, during and after exercise: a comparison of thermocouples and infrared thermography

Measuring skin temperature (TSK) provides important information about the complex thermal control system and could be interesting when carrying out studies about thermoregulation. The most common method to record TSK involves thermocouples at specific locations; however, the use of infrared thermal imaging (IRT) has increased. The two methods use different physical processes to measure TSK, and each has advantages and disadvantages. Therefore, the objective of this study was to compare the mean skin temperature (MTSK) measurements using thermocouples and IRT in three different situations: pre-exercise, exercise and post-exercise. Analysis of the residual scores in Bland-Altman plots showed poor agreement between the MTSK obtained using thermocouples and those using IRT. The averaged error was -0.75 °C during pre-exercise, 1.22 °C during exercise and -1.16 °C during post-exercise, and the reliability between the methods was low in the pre- (ICC = 0.75 [0.12 to 0.93]), during (ICC = 0.49 [-0.80 to 0.85]) and post-exercise (ICC = 0.35 [-1.22 to 0.81] conditions. Thus, there is poor correlation between the values of MTSK measured by thermocouples and IRT pre-exercise, exercise and post-exercise, and low reliability between the two forms of measurement.

Comparison of starts and turns of national and regional level swimmers by individualized-distance measurements

The aim of this study was to compare the race characteristics of the start and turn segments of national and regional level swimmers. In the study, 100 and 200-m events were analysed during the finals session of the Open Comunidad de Madrid (Spain) tournament. The “individualized-distance” method with two-dimensional direct linear transformation algorithm was used to perform race analyses. National level swimmers obtained faster velocities in all race segments and stroke comparisons,although significant inter-level differences in start velocity were only obtained in half (8 out of 16) of the analysed events. Higher level swimmers also travelled for longer start and turn distances but only in the race segments where the gain of speed was high. This was observed in the turn segments, in the backstroke and butterfly strokes and during the 200-m breaststroke event, but not in any of the freestyle events. Time improvements due to the appropriate extension of the underwater subsections appeared to be critical for the end race result and should be carefully evaluated by the “individualized-distance” method.

Comparison of linear and non-linear 2D+T registration methods for DE-MRI cardiac perfusion studies

A series of motion compensation algorithms is run on the challenge data including methods that optimize only a linear transformation, or a non-linear transformation, or both – first a linear and then a non-linear transformation. Methods that optimize a linear transformation run an initial segmentation of the area of interest around the left myocardium by means of an independent component analysis (ICA) (ICA-*). Methods that optimize non-linear transformations may run directly on the full images, or after linear registration. Non-linear motion compensation approaches applied include one method that only registers pairs of images in temporal succession (SERIAL), one method that registers all image to one common reference (AllToOne), one method that was designed to exploit quasi-periodicity in free breathing acquired image data and was adapted to also be usable to image data acquired with initial breath-hold (QUASI-P), a method that uses ICA to identify the motion and eliminate it (ICA-SP), and a method that relies on the estimation of a pseudo ground truth (PG) to guide the motion compensation.

Comparison of implicit and explicit FSI coupling strategies in cardiovascular system = Comparación de las estrategias implícitas y explícitas de acoplamiento FSI en el sistema cardiovascular

Comparación de los esquemas de integración temporal explícito e implícito, en la simulación del flujo sanguíneo y su interacción con la pared arterial. There are two major strategies in FSI coupling techniques: implicit and explicit. The general difference between these methodologies is how many times the data is exchanged between the fluid and solid domains at each FSI time-step. In both coupling strategies, the pressure values coming from fluid domain calculations at each time-step are exported to the solid domain, and consequently, the solid domain is analyzed with these imported forces. In contrast to the explicit coupling, in the implicit approach the fluid and solid domain’s data is exchanged several times until the convergence is achieved. Although this method may boost the numerical stabilization, it increases the computational cost due to the extra data exchanges. In cardiovascular simulations, depending on the analysis objectives, one may choose an explicit or implicit approach. In the current work, the advantage of an explicit coupling strategy is highlighted when simulation of pulsatile blood flow in elastic arteries is desired.

Comparison of Architectures and Performance of Database Replication Systems

One of the most demanding needs in cloud computing and big data is that of having scalable and highly available databases. One of the ways to attend these needs is to leverage the scalable replication techniques developed in the last decade. These techniques allow increasing both the availability and scalability of databases. Many replication protocols have been proposed during the last decade. The main research challenge was how to scale under the eager replication model, the one that provides consistency across replicas. This thesis provides an in depth study of three eager database replication systems based on relational systems: Middle-R, C-JDBC and MySQL Cluster and three systems based on In-Memory Data Grids: JBoss Data Grid, Oracle Coherence and Terracotta Ehcache. Thesis explore these systems based on their architecture, replication protocols, fault tolerance and various other functionalities. It also provides experimental analysis of these systems using state-of-the art benchmarks: TPC-C and TPC-W (for relational systems) and Yahoo! Cloud Serving Benchmark (In- Memory Data Grids). Thesis also discusses three Graph Databases, Neo4j, Titan and Sparksee based on their architecture and transactional capabilities and highlights the weaker transactional consistencies provided by these systems. It discusses an implementation of snapshot isolation in Neo4j graph database to provide stronger isolation guarantees for transactions.

Key quality factors and travellers profiles at interurban interchanges

La planificación y las políticas de transporte no pueden descuidar la calidad del servicio, considerando que influye notablemente en el cambio modal del coche hacia otros medios de transporte más sostenibles. El concepto se aplica también a los intercambiadores de transporte público, los nodos del sistema donde se cruzan las distintas redes del transporte público y privado. Aunque se han logrado numerosos avances para medir y evaluar la calidad en el sector del transporte público, se han dedicado relativamente pocos esfuerzos a investigar estos aspectos relacionados con la calidad de los intercambiadores del transporte público. Este trabajo de investigación se concentra en la calidad del servicio de la transferencia modal en los intercambiadores interurbanos, según la perspectiva de los viajeros. Su objetivo es identificar los factores clave de la calidad del servicio y los perfiles de los viajeros en los intercambiadores. La investigación es exploratoria y ofrece información acerca de la percepción de los viajeros intermodales relacionada con los aspectos de la calidad, aportando nuevos elementos y datos para adentrarse en estudios más detallados. La metodología del trabajo combina técnicas de análisis estadístico multivariante para analizar los datos de las encuestas sobre la satisfacción de los clientes y se subdivide en tres etapas. En primer lugar, se ha implementado el análisis de correspondencias múltiples para explorar los constructos latentes relacionados con la satisfacción de las características cualitativas de los intercambiadores interurbanos, identificando así los factores clave de la calidad. En segundo lugar, se ha aplicado un análisis de conglomerados de k-medias sobre los factores clave de calidad para clasificar a los viajeros en grupos de usuarios de transportes homogéneos, de acuerdo con su percepción de satisfacción, identificando de este modo los perfiles de los viajeros. Por último, se han formulado sugerencias y recomendaciones sobre la calidad para respaldar la formulación de políticas, estableciendo las prioridades para los intercambiadores interurbanos. La metodología se aplicó en cuatro intercambiadores interurbanos (estaciones de ferrocarriles o de autobuses ) en Madrid, Zaragoza, Gothenburg y Lion, analizando los datos recogidos mediante una encuesta de satisfacción del cliente llevada a cabo en 2011 en los cuatro casos de estudio, donde se interconectan distintos medios de transporte público y privado, de corta y larga distancia. Se recogieron datos sobre la satisfacción de los viajeros con 26 criterios de calidad, así como información sobre aspectos socio-económicos y pautas de comportamiento de viajes. Mediante el análisis de correspondencias múltiples se identificaron 4-5 factores clave de calidad en cada intercambiador, que se asocian principalmente con el sistema de emisión de billetes, el confort y la interconexión, mientras que los viajeros no perciben los temas clásicos como la información. Mediante el análisis de conglomerados se identificaron 2-5 perfiles de viajeros en cada intercambiador. Se reconocieron dos grupos de viajeros en casi todos los casos de estudio: viajeros de cercanía/trabajadores y turistas. Por lo que concierne a las prioridades para apoyar a las partes interesadas en la formulación de políticas, la expedición de billetes es el factor clave para los intercambiadores interurbanos españoles, mientras que la interconexión y los aspectos temporales se destacan en los intercambiadores de Francia y Suecia. Quality of Service can not be neglected in public transport planning and policy making, since it strongly influences modal shifts from car to more sustainable modes. This concept is also related to Public Transport interchanges, the nodes of the transport system where the different sub-systems of public passenger transport and personal vehicles meet. Although a lot of progress has been generally done to measure and assess quality in public transport sector, relatively little investigation has been conducted on quality at PT interchanges. This research work focusses on Quality of Service in the use of transfer facilities at interurban interchanges, according to current travellers’ perspective. It aims at identifying key quality factors and travellers profiles at interurban interchanges. The research is exploratory and offers insight into intermodal travellers’ perception on quality aspects, providing new elements and inputs for more definitive investigation. The methodology of the work combines multivariate statistical techniques to analyse data from customer satisfaction surveys and is subdivided in three steps. Firstly, multiple correspondence analysis was performed to explore latent constructs as concern satisfaction of quality attributes at interurban interchanges, thus identifying the so-called Key Quality Factor. Secondly, k-means cluster analysis was implemented on the key quality factors to classify travellers in homogeneous groups of transport users, according to their perception of satisfaction, thus identifying the so-called Travellers Profiles. Finally, hints and recommendations on quality were identified to support policy making, setting priorities for interurban interchanges. The methodology was applied at four interurban interchanges in Madrid, Zaragoza, Gothenburg and Lyon, analysing the data collected through a customer satisfaction survey carried out in 2011 at the four railway or bus stations where different modes of public and private transport are interconnected covering both short and long trips. Data on travellers’ satisfaction with 26 quality attributes were collected, as well as information on socio-economical and travel patterns. Through multiple correspondence analysis were identified 4-5 key quality factors per interchange. They are mainly related to ticketing, comfort and connectivity, while classical issues, as information, are not perceived as important by travellers’. Through cluster analysis were identified 2-5 travellers profiles per interchange. Two groups of travellers can be found in almost all case studies: commuter / business travellers and holiday travellers. As regards the priorities to support stakeholders in policy making, ticketing is the key-issue for the Spanish interurban interchanges, while connectivity and temporal issues emerge in the French and Swedish case studies.