A nonlinear analysis of laying a floating pipeline on the seabed

In this article, a model for the determination of displacements, strains, and stresses of a submarine pipeline during its construction is presented. Typically, polyethylene outfall pipelines are the ones treated by this model. The process is carried out from an initial floating situation to the final laying position on the seabed. The following control variables are considered in the laying process: the axial load in the pipe, the flooded inner length, and the distance of the control barge from the coast. External loads such as self-weight, dead loads, and forces due to currents and small waves are also taken into account.This paper describes both the conceptual framework for the proposed model and its practical application in a real engineering situation. The authors also consider how the model might be used as a tool to study how sensitive the behavior of the pipeline is to small changes in the values of the control variables. A detailed description of the actions is considered, especially the ones related to the marine environment such as buoyancy, current, and sea waves. The structural behavior of the pipeline is simulated in the framework of a geometrically nonlinear dynamic analysis. The pipeline is assumed to be a two-dimensional Navier_Bernoulli beam. In the nonlinear analysis an updated Lagrangian formulation is used, and special care is taken regarding the numerical aspects of sea bed contact, follower forces due to external water pressures, and dynamic actions. The paper concludes by describing the implementation of the proposed techniques, using the ANSYS computer program with a number of subroutines developed by the authors. This implementation permits simulation of the two-dimensional structural pipe behavior of the whole construction process. A sensitivity analysis of the bending moments, axial forces, and stresses for different values of the control variables is carried out. Using the techniques described, the engineer may optimize the construction steps in the pipe laying process

Caracterización multivariada de los temporales para su aplicación en el dimensionamiento del manto principal

En esta tesis se presenta una metodología para la caracterización del oleaje, dentro del marco de las nuevas Recomendaciones para Obras Marítimas (ROM 0.0.-00 y ROM 1.0-09), por ser una de las principales acciones que afectan a la estabilidad de las estructuras marítimas. Debido al carácter aleatorio intrínsecamente multivariado de la acción considerada, las tormentas, su caracterización paramétrica se realiza en términos de funciones cópula uniparamétricas. Las variables consideradas son altura de ola significante del pico de la tormenta, el periodo medio asociado y la magnitud, o número de olas, de todo el ciclo de solicitación. Para establecer un patrón teórico de evolución de la tormenta que permita extrapolar las muestras fuera de la región con datos se analizan los modelos teóricos existentes, comprobándose que no reproducen adecuadamente las tormentas constituidas por estados de mar con un peso importante de oleaje swell. Para evitar esta limitación se proponen cuatro modelos teóricos de evolución de tormentas con distintas formas geométricas. El análisis de los modelos existentes y los propuestos pone de relieve que el Modelo Magnitud Equivalente de Tormenta (EMS= Equivalent Magnitude Storm) con la forma triangular es el que mejor adapta las tormentas constituidas por estados de mar típicos del viento. Para tormentas con un mayor grado de desarrollo, el modelo teórico de tormenta EMS con la forma trapezoidal es el adecuado. De las aproximaciones propuestas para establecer el periodo medio de los sucesivos estados de mar del ciclo de solicitación. la propuesta por Martín Soldevilla et al., (2009) es la más versátil y , en general , mejor reproduce la evolución de todo tipo de tormentas. La caracterización de las tormentas se complementa con la altura de ola máxima. Debido a la mayor disponibilidad y longitud temporal de los datos sintéticos frente a las registros, la práctica totalidad de los análisis de extremos se realizan con tormentas sintéticas en las que la distribución de olas individuales es desconocida. Para evitar esta limitación se utilizan modelos teóricos de distribución de olas acordes a las características de cada uno de los estados de mar que conforman la tormenta sintética. Para establecer dichas características se utiliza la curtosis y en función de su valor la altura de ola máxima se determina asumiendo una determinada distribución de olas. Para estados de mar lineales la distribución de olas individuales de Rayleigh es la considerada. Para condiciones no lineales de gran ancho de banda el modelo de distribución de olas propuesto por Dawson, (2004) es el utilizado y si es de banda estrecha las predicciones de (Boccotti, (1989), Boccotti et al., (2013)) se compara con las resultantes del modelo de Dawson. La caracterización de la evolución de las tormentas en términos multivariados es aplicada al estudio de la progresión del daño del manto principal de diques en talud, y al rebase de las olas. Ambos aspectos cubren el segundo objetivo de la tesis en el que se propone una nueva formulación para el dimensionamiento de mantos constituidos por bloques cúbicos de hormigón. Para el desarrollo de esta nueva formulación se han utilizado los resultados recogidos en los estudios de estabilidad del manto principal de diques talud realizados en modelo físico a escala reducida en el Centro de Estudios de Puertos y Costas (CEDEX) desde la década de los 80 empleando, en su mayoría, bloques paralelepípedos cúbicos de hormigón. Por este motivo y porque los últimos diques construidos en la costa Española utilizan este tipo de pieza, es por lo que la formulación planteada se centra en este tipo de pieza. Después de un primer análisis de las fórmulas de cálculo y de evolución existentes, se llega a la conclusión de que es necesario realizar un esfuerzo de investigación en este campo, así como ensayos en laboratorio y recogida de datos in-situ con base a desarrollar fórmulas de evolución de daño para mantos constituidos por piezas diferentes a la escollera, que tenga en cuenta las principales variables que condiciona su estabilidad. En esta parte de la tesis se propone un método de análisis de evolución de daño, que incluye el criterio de inicio de avería, adecuada para diques en talud constituidos por bloque cúbicos de hormigón y que considera la incidencia oblicua, el daño acumulado y el rebase. This thesis proposes a methodology to estimate sea waves, one of the main actions affecting the maritime structures stability, complying with (ROM 0.0.-00 & ROM 1.0-09.Due to the multivariate behavior of sea storms, the characterization of the structures of sea storms is done using copula function. The analyzed variables are the significant height wave, mean period and magnitude or number of waves during the storm history. The storm evolution in terms of the significant height wave and the mean period is also studied in other to analyze the progressive failure modes. The existing models of evolution are studied, verifying that these approximations do not adjust accurately for developed waves. To overcome this disadvantage, four evolution models are proposed, with some geometrical shapes associated to fit any development degree. The proposed Equivalent Magnitude Storm model, EMS, generally obtains the best results for any kind of storm (predominant sea, swell or both). The triangle is recommended for typical sea storms whereas the trapezoid shape is much more appropriate for more developed storm conditions.The Martín Soldevilla et al., (2009) approach to estimate the mean period is better than others approaches used.The storm characterization is completed with the maximum wave height of the whole storm history. Due to synthetic historical waves databases are more accessible and longer than recorded database, the extreme analyses are done with synthetic data. For this reason the individual waves’ distribution is not known. For that limitation to be avoided, and depending on the characteristics of every sea states, one theoretical model of waves is choose and used. The kurtosis parameter is used to distinguish between linear and nonlinear sea states. The Rayleigh model is used for the linear sea states. For the nonlinear sea states, Dawson, (2004) approach is used for non-narrow bandwidth storms, comparing the results with the Boccotti, (1989), Boccotti et al., (2013) approach, with is used for narrow bandwidth storms. The multivariate and storm evolution characterization is used to analyze of stone armour damage progression and wave overtopping discharge. Both aspects are included in the second part of the thesis, with a new formula is proposed to design cubes armour layer. The results the stability studies of armour layer, done in the Centre for Harbours and Coastal Studies (CEDEX) laboratory are used for defining a new stability formula. For this reason and because the last biggest breakwater built in Spain using the cube, the damage progression is analyze for this kind of concrete block. Before to analyze the existing formulae, it is concluded that it is necessary more investigation, more tests in laboratory and data gathering in situ to define damage evolution formulae to armour of other kind of pieces and that takes to account the principal variables. This thesis proposed a method to calculate the damage progression including oblique waves, accumulated damage, and overtopping effect. The method also takes account the beginning of the movement of the blocks.

Estudio dinámico de cimentaciones en obras portuarias

Los diques de abrigo verticales son estructuras monolíticas que sirven para reflejar el oleaje creando, de este modo, una zona abrigada en el lado tierra. Son estructuras de contención de gravedad, es decir, su peso es el elemento resistente fundamental. Las solicitaciones sobre estas estructuras son de tipo dinámico (oleaje) y consisten, fundamentalmente, en un empuje frontal y una subpresión en la base que varían en el tiempo. Habitualmente, las acciones sobre los diques de abrigo se establecen mediante fórmulas empíricas, que se describen en la presente tesis si bien, para obras de especial importancia, suelen medirse en modelos reducidos de laboratorio. Cuando el cimiento en que han de apoyarse estas estructuras no presenta una resistencia al corte suficiente, el apoyo se realiza en banquetas que redistribuyen la carga y que están formadas por materiales granulares. En la práctica habitual para conocer la estabilidad de estas estructuras frente a un temporal, tras establecer las acciones de cálculo (empuje frontal y subpresión) se efectúa un cálculo pseudoestático en el que se consideran condiciones drenadas o no drenadas del cimiento en función de su permeabilidad. Se conoce que en los suelos saturados, bajo cargas cíclicas, tiende a producirse una elevación de las presiones intersticiales y una reducción de tensiones efectivas así como una degradación del módulo de deformación tangencial en función del número de ciclos de carga, pudiéndose producir el fenómeno conocido como licuefacción (arenas) o movilidad cíclica (suelos más finos). El objeto de la tesis es explorar la posibilidad, con la tecnología actual, de analizar la estabilidad de los diques de abrigo verticales en cuyo cimiento existen suelos blandos, proponiendo un procedimiento para evaluar la estabilidad dinámica en este tipo de obras. Para ello se han revisado los procedimientos actualmente utilizados para definir las acciones de cálculo, los principales modelos de comportamiento dinámicos de suelos saturados disponibles y los procedimientos de cálculo. Una vez investigado el estado del arte sobre este tema, se propone un procedimiento de cálculo en el que, utilizando el programa comercial FLAC, se establecen las acciones cíclicas sobre un dique de abrigo vertical tipo con distintas condiciones de apoyo, aplicando, para el cimiento, un modelo de comportamiento tipo hiperbólico con generación de presiones intersticiales cuyos parámetros pueden obtenerse de ensayos de campo y laboratorio. Por último, una vez descrito el procedimiento, se aplica a un caso real en el que se produjo un fallo en la cimentación que desembocó en el hundimiento de parte de un dique vertical situado en el puerto de Barcelona, presentándose los resultados obtenidos del análisis efectuado y comparándolos con los obtenidos utilizando los métodos de cálculo habituales. Vertical breakwaters are monolithic structures built to reflect sea waves, thereby providing a sheltered area on the land side. They are gravity retaining structures, that is, their own weight is their basic resisting mechanism. Loads acting on these structures are dynamic (waves) and consist essentially in a frontal thrust and an uplift pressure on the base, which both vary over time. Usually, actions in breakwater design are established by empirical formulas, which are described in this thesis. For works of particular importance, such forces are measured in small-scale laboratory tests. When there are no soils with enough shear strength under the planned vertical breakwaters, they usually rest on granular berms which redistribute the load. Nowadays, after establishing the acting forces on the breakwater (front push and uplift pressure), a pseudostatic calculation (with drained or undrained conditions depending on the foundation permeability) is normally done to analyze the stability of these structures against storm waves. It is known that pore pressures tend to rise in saturated soils under cyclic loading and, consequently, there is a reduction of effective stress. A degradation of the shear modulus also occurs depending on the number of load cycles. All of these effects can bring about the phenomenon known as liquefaction in sands or cyclic mobility in fine-grained soils. The aim of the thesis is to explore the possibility that current technology provides to analyze the stability of vertical breakwaters founded on soft soils, and to suggest a method to evaluate the dynamic stability in this type of works. To this end, a review has been made of procedures currently used to define the actions in calculations, the main models of dynamic behaviour of saturated soils available and of calculation procedures. Once the state of the art on this subject has been reviewed, a method of calculation is proposed that uses the commercial program FLAC and is applied to a typical vertical breakwater on a range of different foundation conditions. For the foundation soil, a hyperbolic constitutive model with pore pressure generation has been employed, whose parameters can be obtained from field and laboratory tests. Finally, the described procedure is applied to an actual case where a foundation failure occurred that led to the sinking of several caissons in a vertical breakwater located in the port of Barcelona. The results obtained with the proposed method are compared with those obtained using conventional methods.

Improvement of theoretical storm characterization for different climate conditions

The different theoretical models related with storm wave characterization focus on determining the significant wave height of the peak storm, the mean period and, usually assuming a triangle storm shape, their duration. In some cases, the main direction is also considered. Nevertheless, definition of the whole storm history, including the variation of the main random variables during the storm cycle is not taken into consideration. The representativeness of the proposed storm models, analysed in a recent study using an empirical maximum energy flux time dependent function shows that the behaviour of the different storm models is extremely dependent on the climatic characteristics of the project area. Moreover, there are no theoretical models able to adequately reproduce storm history evolution of the sea states characterized by important swell components. To overcome this shortcoming, several theoretical storm shapes are investigated taking into consideration the bases of the three best theoretical storm models, the Equivalent Magnitude Storm (EMS), the Equivalent Number of Waves Storm (ENWS) and the Equivalent Duration Storm (EDS) models. To analyse the representativeness of the new storm shape, the aforementioned maximum energy flux formulation and a wave overtopping discharge structure function are used. With the empirical energy flux formulation, correctness of the different approaches is focussed on the progressive hydraulic stability loss of the main armour layer caused by real and theoretical storms. For the overtopping structure equation, the total volume of discharge is considered. In all cases, the results obtained highlight the greater representativeness of the triangular EMS model for sea waves and the trapezoidal (nonparallel sides) EMS model for waves with a higher degree of wave development. Taking into account the increase in offshore and shallow water wind turbines, maritime transport and deep vertical breakwaters, the maximum wave height of the whole storm history and that corresponding to each sea state belonging to its cycle's evolution is also considered. The procedure considers the information usually available for extreme waves' characterization. Extrapolations of the maximum wave height of the selected storms have also been considered. The 4th order statistics of the sea state belonging to the real and theoretical storm have been estimated to complete the statistical analysis of individual wave height

A non-linear analysis of lying a floating pipeline on the seabed

In this article, a model for the determination of displacements, deformations and tensions of a submarine pipeline during the construction is presented. The process is carried out from an initial floating situation to the final laying position on the seabed. The existence of currents and small waves are also considered. Firstly, this technique, usually applied to polyethylene pipelines, is described in this paper as well as some real world examples, as well as the variables that can be modified to control the behavior of the structure. A detailed description of the actions in this process is considered, specially the ones related to marine environment, as Archimedes force, current and sea waves. The behavior of the pipeline is modeled with a non linear elasto dynamic model where geometric non linearities are taken into account. A 3-D beam model, without cross section deformation effects, is developed. Special care is taken in the numerical analysis, developed within an updated lagrangian formulation framework, with the sea bed contact, the follower forces due to the external water pressures and the dynamic actions. Finally, some subroutines are implemented into ANSYS to simulate the two dimensional case, where the whole construction process is achieved. With this software, a sensibility analysis of the bending moments, axial forces and stresses obtained with different values of the control variables in order to optimize the construction steps. These control variables are, the axial load in the pipe, the inundated inner length and the distance of the control barge from the coast.

Variational Stereo Imaging of Oceanic Waves with Statistical Constraints

An image processing observational technique for the stereoscopic reconstruction of the wave form of oceanic sea states is developed. The technique incorporates the enforcement of any given statistical wave law modeling the quasi Gaussianity of oceanic waves observed in nature. The problem is posed in a variational optimization framework, where the desired wave form is obtained as the minimizer of a cost functional that combines image observations, smoothness priors and a weak statistical constraint. The minimizer is obtained combining gradient descent and multigrid methods on the necessary optimality equations of the cost functional. Robust photometric error criteria and a spatial intensity compensation model are also developed to improve the performance of the presented image matching strategy. The weak statistical constraint is thoroughly evaluated in combination with other elements presented to reconstruct and enforce constraints on experimental stereo data, demonstrating the improvement in the estimation of the observed ocean surface.

Offshore stereo measurements of gravity waves: classical epipolar and novel variational techniques

Stereo video techniques are effective for estimating the space-time wave dynamics over an area of the ocean. Indeed, a stereo camera view allows retrieval of both spatial and temporal data whose statistical content is richer than that of time series data retrieved from point wave probes. Classical epipolar techniques and modern variational methods are reviewed to reconstruct the sea surface from the stereo pairs sequentially in time. Current improvements of the variational methods are presented.

Space-time Reconstruction of Oceanic Sea States via Variational Stereo Methods

We present a remote sensing observational method for the measurement of the spatio-temporal dynamics of ocean waves. Variational techniques are used to recover a coherent space-time reconstruction of oceanic sea states given stereo video imagery. The stereoscopic reconstruction problem is expressed in a variational optimization framework. There, we design an energy functional whose minimizer is the desired temporal sequence of wave heights. The functional combines photometric observations as well as spatial and temporal regularizers. A nested iterative scheme is devised to numerically solve, via 3-D multigrid methods, the system of partial differential equations resulting from the optimality condition of the energy functional. The output of our method is the coherent, simultaneous estimation of the wave surface height and radiance at multiple snapshots. We demonstrate our algorithm on real data collected off-shore. Statistical and spectral analysis are performed. Comparison with respect to an existing sequential method is analyzed.

A Variational Stereo Method for the Three-Dimensional Reconstruction of Ocean Waves

We develop a novel remote sensing technique for the observation of waves on the ocean surface. Our method infers the 3-D waveform and radiance of oceanic sea states via a variational stereo imagery formulation. In this setting, the shape and radiance of the wave surface are given by minimizers of a composite energy functional that combines a photometric matching term along with regularization terms involving the smoothness of the unknowns. The desired ocean surface shape and radiance are the solution of a system of coupled partial differential equations derived from the optimality conditions of the energy functional. The proposed method is naturally extended to study the spatiotemporal dynamics of ocean waves and applied to three sets of stereo video data. Statistical and spectral analysis are carried out. Our results provide evidence that the observed omnidirectional wavenumber spectrum S(k) decays as k-2.5 is in agreement with Zakharov's theory (1999). Furthermore, the 3-D spectrum of the reconstructed wave surface is exploited to estimate wave dispersion and currents.

Space-time Measurements of Oceanic Sea States

Stereo video techniques are effective for estimating the space–time wave dynamics over an area of the ocean. Indeed, a stereo camera view allows retrieval of both spatial and temporal data whose statistical content is richer than that of time series data retrieved from point wave probes. We present an application of the Wave Acquisition Stereo System (WASS) for the analysis of offshore video measurements of gravity waves in the Northern Adriatic Sea and near the southern seashore of the Crimean peninsula, in the Black Sea. We use classical epipolar techniques to reconstruct the sea surface from the stereo pairs sequentially in time, viz. a sequence of spatial snapshots. We also present a variational approach that exploits the entire data image set providing a global space–time imaging of the sea surface, viz. simultaneous reconstruction of several spatial snapshots of the surface in order to guarantee continuity of the sea surface both in space and time. Analysis of the WASS measurements show that the sea surface can be accurately estimated in space and time together, yielding associated directional spectra and wave statistics at a point in time that agrees well with probabilistic models. In particular, WASS stereo imaging is able to capture typical features of the wave surface, especially the crest-to-trough asymmetry due to second order nonlinearities, and the observed shape of large waves are fairly described by theoretical models based on the theory of quasi-determinism (Boccotti, 2000). Further, we investigate space–time extremes of the observed stationary sea states, viz. the largest surface wave heights expected over a given area during the sea state duration. The WASS analysis provides the first experimental proof that a space–time extreme is generally larger than that observed in time via point measurements, in agreement with the predictions based on stochastic theories for global maxima of Gaussian fields.

Offshore Measurements of Ocean Waves using Stereo Vision Systems

In recent years, remote sensing imaging systems for the measurement of oceanic sea states have attracted renovated attention. Imaging technology is economical, non-invasive and enables a better understanding of the space-time dynamics of ocean waves over an area rather than at selected point locations of previous monitoring methods (buoys, wave gauges, etc.). We present recent progress in space-time measurement of ocean waves using stereo vision systems on offshore platforms, which focus on sea states with wavelengths in the range of 0.01 m to 10 m. Classical epipolar techniques and modern variational methods are reviewed to reconstruct the sea surface from the stereo pairs sequentially in time. The statistical and spectral properties of the resulting observed waves are analyzed. Current improvements of the variational methods are discussed as future lines of research.

Offshore stereo measurements of gravity waves

Stereo video techniques are effective for estimating the space-time wave dynamics over an area of the ocean. Indeed, a stereo camera view allows retrieval of both spatial and temporal data whose statistical content is richer than that of time series data retrieved from point wave probes. To prove this, we consider an application of the Wave Acquisition Stereo System (WASS) for the analysis of offshore video measurements of gravity waves in the Northern Adriatic Sea. In particular, we deployed WASS at the oceanographic platform Acqua Alta, off the Venice coast, Italy. Three experimental studies were performed, and the overlapping field of view of the acquired stereo images covered an area of approximately 1100 m2. Analysis of the WASS measurements show that the sea surface can be accurately estimated in space and time together, yielding associated directional spectra and wave statistics that agree well with theoretical models. From the observed wavenumber-frequency spectrum one can also predict the vertical profile of the current flow underneath the wave surface. Finally, future improvements of WASS and applications are discussed.