An analysis of installation of submarine pipelines

There are different methods of construction of outfall pipelines, all of them have to solve the problem of placing a tube over a known location in sea bed. This process has sometimes to be done in difficult conditions as waves, current or depths greater than 30 metres, where a diver cannot go safely beyond. Also the placement of the pipeline must be carried out without any damage to the tube, therefore a close control of the deflections and stresses in the structure must be performed. The importance of this control should be not diminished because a damage during the construction would imply a very difficult and expensive repair, that should be avoided with a proper design of the construction process. This paper is focused in the analysis of the tube during its placement according to a very well known construction method consisting in placing the tube from a boat, where all the connections between consecutive tube segments are performed, and also the whole process is controlled. This method is used for outfall as well as offshore pipelines, and it will be described in Section 2

Development of FEM/BEM and SEA models from experimental results for structural elements with attached equipment

This work focuses on the analysis of a structural element of MetOP-A satellite. Given the special interest in the influence of equipment installed on structural elements, the paper studies one of the lateral faces on which the Advanced SCATterometer (ASCAT) is installed. The work is oriented towards the modal characterization of the specimen, describing the experimental set-up and the application of results to the development of a Finite Element Method (FEM) model to study the vibro-acoustic response. For the high frequency range, characterized by a high modal density, a Statistical Energy Analysis (SEA) model is considered, and the FEM model is used when modal density is low. The methodology for developing the SEA model and a compound FEM and Boundary Element Method (BEM) model to provide continuity in the medium frequency range is presented, as well as the necessary updating, characterization and coupling between models required to achieve numerical models that match experimental results.

Promoting mixed stands through conversion treatments. Effect of holm oak coppices thinning on black pine regeneration

The effects of conversion treatments, depending on ecological factors and silvicultural parameters (thinning intensity, thinning type and rotation, among others) have been studied during the last fifteen years in an experimental trial in Central Spain. The general climate is continental Mediterranean; soils are low depth and limy; vegetation is an homogeneous dense coppices of Quercus ilex with isolated Pinus nigra trees. The experimental design (three locations) includes different thinning intensities (from 0 to 100% of extracted basal area). Inventories have been carried out in 1994 and 2010; thinning treatments were done in 1995 and 2011. Analysis of the effects of the conversion treatment show the increment of diameter and height growth rates, the canopy recovery and the stand resprouting, finding differences in these effects between thinning treatments. Besides the induced changes at holm oak stand, the application of conversion treatment clearly changed the woodland dynamics. Fifteen years after the thinnings, floristic composition varied and an abundant pine regeneration was installed in the woodland. In this work we describe the changes between inventories in tree species composition and diameter distribution, specially in the case of black pine. The conversion treatment caused changes in forest dynamics in the short term, increasing biodiversity and diversifying the forest structure. The fast installation of Pinus regeneration suggests the potential of the zone for the establishment of multipurpose mixed Quercus-Pinus stands in wide areas where Quercus species were favoured by human populations for firewood production. Conversion treatment of coppices, with the creation of mixed stands, constitutes a good management alternative for extensive areas and an interesting technique to adaptation to global change.

Estudio de los riesgos técnicos aplicados al diseño y construcción de cimentaciones para máquinas

En el Código Técnico de la Edificación se define el riesgo como medida del alcance del peligro que representa un evento no deseado para las personas, expresado en términos de probabilidad vinculada a las consecuencias de un evento, también se expresa como Exigencia Básica de Resistencia y Estabilidad, que estas serán las adecuadas para que no se generen riesgos indebidos manteniendo la resistencia y estabilidad frente a las acciones e influencias previsibles durante la construcción y usos previstos de los edificios, y que además, los posibles eventos extraordinarios que puedan producirse no originen consecuencias desproporcionadas respecto a la causa original. Es ahora donde la gestión de riesgos juega un papel muy importante en la sociedad moderna, siendo esta cada vez más exigente con los resultados y calidad de productos y servicios, además de cumplir también con la responsabilidad jurídica que trae la concepción, diseño y construcción de proyectos de gran envergadura como los son la obra civil y edificación. La obra civil destinada al sector industrial debe ser ejecutada con la mayor precisión posible, pues requiere la instalación de complejos equipos y sistemas productivos que pueden producir esfuerzos dinámicos que muchas veces no se consideran en el diseño de los cimientos que lo soportan, razón por la cual interviene la gestión de riesgos para conocer y reducir los posibles riesgos de fallos que se puedan generar y así intentar aproximarse cada vez más al desarrollo de diseños eficientes y confiables, afianzando la exactitud y minimizando errores en la producción y elaboración de piezas, sistemas y equipos de las distintas áreas productivas de la industria. El presente trabajo de investigación se centra en el estudio de los riesgos técnicos existentes en el diseño y ejecución de cimentaciones para maquinarias, mediante la aplicación de varios métodos de investigación, a fin de intentar cubrir los aspectos más importantes que puedan incurrir en una posible causa de fallo de la estructura, evaluando el acoplamiento entre el sistema máquina-cimiento-suelo. Risk is defined, by the Technical Building Code (Código Técnico de la Edificación, CTE) as a measure of the scope of the hazard of an undesired event for people, expressed in terms of probability related to the consequences of an event, also is expressed as a Basic Requirement Strength and Stability these will be appropriate to not cause undue risk maintaining strength and stability against predictable actions and influences during construction and expected uses of the buildings. Nowadays, Risk Management is an important process in modern society, becoming ever more demanding about the results and quality of products and services, and also complies with the legal responsibility that brings the conception, design and construction of large projects as are civil engineering and construction projects. Civil work as a part of industry must be performed as accurately as possible, requiring the installation of sophisticated equipment and production systems which can produce dynamic forces that often are not considered in the design of the foundations, this is the reason why risk management is involved to understand and reduce the risks of failures that may arise and try to move closer to the development of efficient and reliable designs, strengthening the accuracy and minimizing errors in the production and processing of parts, systems and equipments from different production areas of the industry. This paper is a study of existing technical risks in the design and execution of foundations for machinery, through the application of various research methods, in order to try to cover the most important aspects that may produce the failure of the structure, evaluating the union between the machine-foundation system and soil.

Diseño del equipamiento de un estudio de grabación digital

El presente proyecto describe la instalación de audio de un estudio de grabación digital musical. La finalidad de este proyecto es puramente educativa, afianzando conceptos que se han contemplado durante la carrera. La instalación tiene carácter ficticio, por lo que no tiene implementación real. Aun así, se ha intentado desarrollar con carácter profesional. El proyecto se ha dividido en varias fases de trabajo. Primeramente, se procedió a la búsqueda de información relativa a estudios de grabación, atendiendo principalmente a sus configuraciones. Paralelamente, se buscó información sobre los principales equipos dentro de un estudio de grabación y realizando un pequeño estudio de mercado. Posteriormente, se ha procedido a la elección de la configuración del equipamiento del estudio, atendiendo a las ventajas e inconvenientes de cada tipo de configuración. La tercera fase, corresponde a la elección de los equipos. Siguiendo la cadena de audio, se ha ido analizando la necesidad de cada uno de ellos. Seguidamente, se ha realizado una comparación de diferentes equipos que componen cada bloque de elección, y finalmente la selección del más apropiado junto con su justificación. En la última fase se ha realizado la interconexión de todos los equipos atendiendo a la configuración elegida en la segunda fase. Para ello, se ha llevado a cabo la implementación de una serie de tablas escritas, donde se especifica cada tipo de conexión. El proyecto ha terminado con una presentación del presupuesto, dividido en varios aparatados, y el desarrollo de las conclusiones. En ellas, se ha analizado tanto los objetivos propuestos al principio del proyecto como una valoración personal del proyecto en general. ABSTRACT. This project describes the audio installation of a digital music recording studio. The purpose of this project is purely educational, strengthening concepts that have been laid during college. The installation is fictitious and has not been implemented in a real situation. Nevertheless, it has been developed with a professional character. This project has been divided in various phases. Firstly, I proceeded to search information related to recording studios, focusing specially on their configurations. Simultaneously, I looked for information about the main digital equipment of a recording studio and performed a brief market research. Secondly, I selected the studio equipment configuration, taking care of the advantages and disadvantages of each type of configuration. The third phase corresponds to the choice of the equipment. Following the audio chain, I analyzed the need for each of them. Then, I compared the different equipment that compose each of the choice blocks and finally opt for the most appropriate with its justification. In the last phase, I interconnected all the equipment according to the chosen configuration of the second phase. For this, I implemented a series of written tables, where I specified each connection type. The Project ends with a presentation of the budget, divided into several sections, followed by the conclusion in which I analyze both the objectives of the project and my personal valuation.

Effectiveness of improved cookstoves to reduce indoor air pollution in developing countries. The case of the cassamance natural subregion, Western Africa

The Spanish NGO "Alianza por la Solidaridad" has installed improved cookstoves in 3000 households during 2012 and 2013 to improve energy efficiency reducing fuelwood consumption and to improve in-door air quality. The type of cookstoves were Noflaye Jeeg and Noflaye Jaboot and were installed in the Cassamance Natural Subregion covering part of Senegal, The Gambia and Guinea-Bissau. The Technical University of Madrid (UPM) has conducted a field study on a sample of these households to assess the effect of improved cookstoves on kitchen air quality. Measurements of carbon monoxide (CO) and fine particle matter (PM2.5) were taken for 24-hr period before and after the installation of improved cook-stoves. The 24-hr mean CO concentrations were lower than the World Health Organization (WHO) guidelines for Guinea-Bissau but higher for Senegal and Gambia, even after the installation of improved cookstoves. As for PM2.5 concentrations, 24-hr mean were always higher than these guidelines. However, improved cookstoves produced significant reductions on 24-hr mean CO and PM2.5 concentrations in Senegal and for mean and maximum PM2.5 concentration on Gambia. Although this variability needs to be explained by further research to determine which other factors could affect indoor air pollution, the study provided a better understanding of the problem and envisaged alternatives to be implemented in fu-ture phases of the NGO project.

NGCPV: a new generation of concentrator photovoltaic cells, modules and systems

Starting on June 2011, NGCPV is the first project funded jointly between the European Commission (EC) and the New Energy and Industrial Technology Development Organization (NEDO) of Japan to research on new generation concentration photovoltaics (CPV). The Project, through a collaborative research between seven European and nine Japanese leading research centers in the field of CPV, aims at lowering the cost of the CPVproduced photovoltaic kWh down to 5 ?cents. The main objective of the project is to improve the present concentrator cell, module and system efficiency, as well as developing advanced characterization tools for CPV components and systems. As particular targets, the project aims at achieving a cell efficiency of at least 45% and a CPV module with an efficiency greater than 35%. This paper describes the R&D activities that are being carried out within the NGCPV project and summarizes some of the most relevant results that have already been attained, for instance: the manufacturing of a 44.4% world record efficiency triple junction solar cell (by Sharp Corp.) and the installation of a 50 kWp experimental CPV plant in Spain, which will be used to obtain accurate forecasts of the energy produced at system level.

Diseño de una vivienda unifamiliar con instalación geotérmica de muy baja entalpía

El objetivo del presente proyecto es el diseño de una vivienda unifamiliar de manera que el aporte de energía no renovable sea el mínimo para conseguir las condiciones de confort óptimas para los ocupantes durante todo el año. Para su diseño se tendrá en cuenta el aporte de energía solar pasiva y el uso de aislantes térmicos a lo largo de la envolvente para la reducción de las necesidades de energía. Se dimensiona una instalación geotérmica para el abastecimiento de calefacción, refrigeración y agua caliente sanitaria (ACS). En este dimensionamiento se incluyen los sondeos geotérmicos, el equipo de bomba de calor y la instalación de suelo radiante. En el estudio de iluminación se analizan las necesidades de alumbrado de la vivienda utilizando luminarias led. Por último se evalúa la viabilidad económica que supone sustituir una instalación de caldera de gasoil por la instalación geotérmica dimensionada y la viabilidad de sustituir luminarias incandescentes por luminarias led. ABSTRACT The purpose of this paper is the design of a single family home with the lowest nonrenewable energy input, so optimum comfort living conditions for the occupants during the whole year can be reached. In order to design the house, both passive solar energy input and the use of thermal insulators will be taken into account. A geothermal installation for the heating, cooling and Domestic Hot Water (DHC) supply will be measured. In this measuring, the boreholls, the heat pump equipment and the radiant floor heating installation are included. In the study of illumination of the house, the lighting needs using LED luminaires are analised. Finally, the economic viability when replacing the installation of a diesel boiler for the measured geothermal installation is assessed, as well as the viability when replacing incandescent luminaires for LED luminaires

Nueva disposición de sistemas de contención de vehículos en medianas de autovía: New practices for median barriers of highways

La siniestralidad por salida izquierda de vía en carreteras de gran capacidad es un problema que, además de las dramáticas situaciones a las que da lugar, inflige a la sociedad elevados costes. Por ello, debe prestarse una intensa atención al diseño de las medianas y a la disposición de barreras en ellas, con el objetivo de evitar que se produzcan este tipo de accidentes y limitar las consecuencias de los que aún así tengan lugar. Habitualmente las medianas de autovías se diseñan aplicando casi sistemáticamente los parámetros mínimos exigidos normativamente y generalmente con barreras de seguridad adosadas o muy próximas a uno de los arcenes interiores. Sin embargo, tanto las recomendaciones técnicas nacionales como la bibliografía internacional recomiendan llevar a cabo un estudio económico de alternativas antes que colocar barreras y, si está justificada su disposición, alejarla de la calzada disponiéndola próxima al eje de la mediana. En esta tesis se analizan las ventajas y limitaciones que tiene la disposición de barrera próxima al eje de la mediana. Se ha investigado sobre el comportamiento de los vehículos al circular por la mediana y se muestra cómo se ha instalado en la obra de la autovía A‐40, Tramo: Villarrubia de Santiago‐Santa Cruz de la Zarza, destacando los aspectos más novedosos y llamativos pero que se ajustan a las mejores prácticas en la materia y también a la normativa de aplicación. ABSTRACT Many dramatic situations are caused by cross‐median traffic accidents which imply high costs for society, both in human and economic terms. It is therefore important that special attention should be paid to the design of highway medians and to the installation of safety barriers so as to avoid these kinds of incidents and to reduce their consequences. Highway median are usually designed with the application of minimum parameters, according to regulations, with the installation of safety barriers against or close to the inside border. However, Spanish technical regulations and international bibliography recommend a prior study to be carried out with the purpose of finding alternatives to this installation of safety barriers and if necessary, the installation of the safety barrier close to the centre of the median. This thesis directs its analysis towards the advantages and restrictions of installing the safety barrier close to the centre of the median. Research has shown vehicle response when within the median and we show the installation of safety barriers in the A‐40 highway stretch: Villarrubia de Santiago – Santa Cruz de la Zarza, highlighting the aspects that should be taken into account as best practices for road safety and technical regulations.

Diseño acústico y electroacústico de Waipahu Transit Center en Honolulú, Hawái

El objetivo de este Proyecto Fin de Grado es el diseño de megafonía y PAGA (Public Address /General Alarm) de la estación de tren Waipahu Transit Center en la ciudad de Honolulú, Hawái. Esta estación forma parte de una nueva línea de tren que está en proceso de construcción actualmente llamada Honolulu Rail Transit. Inicialmente la línea de tren constará de 21 estaciones, en las que prácticamente todas están diseñadas como pasos elevados usando como referencia las autopistas que cruzan la isla. Se tiene prevista su fecha de finalización en el año 2019, aunque las primeras estaciones se inaugurarán en 2017. Se trata en primer lugar un estudio acústico del recinto a sonorizar, eligiendo los equipos necesarios: conmutadores, altavoces, amplificadores, procesador, equipo de control y micrófonos. Este primer estudio sirve para obtener una aproximación de equipos necesarios, así como la posible situación de estos dentro de la estación. Tras esto, se procede a la simulación de la estación mediante el programa de simulación acústica y electroacústica EASE 4.4. Para ello, se diseña la estación en un modelo 3D, en el que cada superficie se asocia a su material correspondiente. Para facilitar el diseño y el cómputo de las simulaciones se divide la estación en 3 partes por separado. Cada una corresponde a un nivel de la estación: Ground level, el nivel inferior que contiene la entrada; Concourse Level, pasillo que comunica los dos andenes; y Platform Level, en el que realizarán las paradas los trenes. Una vez realizado el diseño se procede al posicionamiento de altavoces en los diferentes niveles de la estación. Debido al clima existente en la isla, el cual ronda los 20°C a lo largo de todo el año, no es necesaria la instalación de sistemas de aire acondicionado o calefacción, por lo que la estación no está totalmente cerrada. Esto supone un problema al realizar las simulaciones en EASE, ya que al tratarse de un recinto abierto se deberán hallar parámetros como el tiempo de reverberación o el volumen equivalente por otros medios. Para ello, se utilizará el método Ray Tracing, mediante el cual se halla el tiempo de reverberación por la respuesta al impulso de la sala; y a continuación se calcula un volumen equivalente del recinto mediante la fórmula de Eyring. Con estos datos, se puede proceder a calcular los parámetros necesarios: nivel de presión sonora directo, nivel de presión sonora total y STI (Speech Transmission Index). Para obtener este último será necesario ecualizar antes en cada uno de los niveles de la estación. Una vez hechas las simulaciones, se comprueba que el nivel de presión sonora y los valores de inteligibilidad son acordes con los requisitos dados por el cliente. Tras esto, se procede a realizar los bucles de altavoces y el cálculo de amplificadores necesarios. Se estudia la situación de los micrófonos, que servirán para poder variar la potencia emitida por los altavoces dependiendo del nivel de ruido en la estación. Una vez obtenidos todos los equipos necesarios en la estación, se hace el conexionado entre éstos, tanto de una forma simplificada en la que se pueden ver los bucles de altavoces en cada nivel de la estación, como de una forma más detallada en la que se muestran las conexiones entre cada equipo del rack. Finalmente, se realiza el etiquetado de los equipos y un presupuesto estimado con los costes del diseño del sistema PAGA. ABSTRACT. The aim of this Final Degree Project is the design of the PAGA (Public Address / General Alarm) system in the train station Waipahu Transit Center in the city of Honolulu, Hawaii. This station is part of a new rail line that is currently under construction, called Honolulu Rail Transit. Initially, the rail line will have 21 stations, in which almost all are designed elevated using the highways that cross the island as reference. At first, it is treated an acoustic study in the areas to cover, choosing the equipment needed: switches, loudspeakers, amplifiers, DPS, control station and microphones. This first study helps to obtain an approximation of the equipments needed, as well as their placement inside the station. Thereafter, it is proceeded to do the simulation of the station through the acoustics and electroacoustics simulation software EASE 4.4. In order to do that, it is made the 3D design of the station, in which each surface is associated with its material. In order to ease the design and calculation of the simulations, the station has been divided in 3 zones. Each one corresponds with one level of the station: Ground Level, the lower level that has the entrance; Concourse Level, a corridor that links the two platforms; and Platform Level, where the trains will stop. Once the design is made, it is proceeded to place the speakers in the different levels of the station. Due to the weather in the island, which is about 20°C throughout the year, it is not necessary the installation of air conditioning or heating systems, so the station is not totally closed. This cause a problem when making the simulations in EASE, as the project is open, and it will be necessary to calculate parameters like the reverberation time or the equivalent volume by other methods. In order to do that, it will be used the Ray Tracing method, by which the reverberation time is calculated by the impulse response; and then it is calculated the equivalent volume of the area with the Eyring equation. With this information, it can be proceeded to calculate the parameters needed: direct sound pressure level, total sound pressure level and STI (Speech Transmission Index). In order to obtain the STI, it will be needed to equalize before in each of the station’s levels. Once the simulations are done, it is checked that the sound pressure level and the intelligibility values agree with the requirements given by the client. After that, it is proceeded to perform the speaker’s loops and the calculation of the amplifiers needed. It is studied the placement of the microphones, which will help to vary the power emitted by the speakers depending on the background noise level in the station. Once obtained all the necessary equipment in the station, it is done the connection diagram, both a simplified diagram in which there can be seen the speaker’s loops in each level of the station, or a more detailed diagram in which it is shown the wiring between each equipment of the rack. At last, it is done the labeling of the equipments and an estimated budget with the expenses for the PAGA design.

Aplicación de distintas metodologías a la monitorización de la humedad del suelo y al cálculo del balance hídrico diario

Dada la importancia de conocer la humedad del suelo de forma precisa y en tiempo real, se ha realizado este trabajo de investigación cuyo objetivo principal ha sido seleccionar un Balance Hídrico del Suelo (BHS) diario y validar sus estimaciones de humedad del suelo frente a medidas obtenidas “in situ”, aplicándolo a tres emplazamientos seleccionados en la zona centro con características edáficas y climáticas diferentes, y de este modo estimar con cierta precisión la humedad del suelo como Agua Disponible (AD) para las plantas y a su vez permitir la realización de estudios climáticos. Los observatorios meteorológicos seleccionados fueron: Guadalajara/El Serranillo en la zona aluvial del río Henares; Colmenar Viejo/Base Famet en la rampa sur del Guadarrama sobre rocas metamórficas; y Radiosondeo/Madrid(Barajas) en arenas arcósicas de grano grueso. Se realizó una caracterización morfológica y un estudio de las propiedades físicas, químicas e hidrofísicas de los suelos en cada emplazamiento. El suelo de Guadalajara, Xerorthent Típico presenta una secuencia genética de horizontes (Ap-AC-C1-C2) siendo su clase textural entre franco-arenosa a franca, con menos del 2% de elementos gruesos, presencia de caliza a lo largo de todo el perfil, destacando la homogeneidad en vertical y horizontal de sus propiedades. El suelo de Colmenar, Xerorthent Dystrico, presenta una secuencia genética de horizontes (A-C-C/R) apareciendo el horizonte C/R entre 20-30 cm; y la roca aproximadamente a unos 30 cm; destacando en este perfil su acidez y el alto contenido de elementos gruesos. El suelo de Radiosondeo, Haploxeralf Típico, presenta la secuencia normal de horizontes de los alfisoles (A-Bt1-Bt2-C/Bt); destacando su heterogeneidad principalmente en el plano horizontal, con presencia del Bt a diferentes profundidades en un corto espacio longitudinal. En una primera fase de experimentación (2007-2008) se seleccionaron BHS diarios que sólo utilizaban como datos de entrada la información de variables meteorológicas y el valor del Agua Disponible Total (ADT) para cada tipo de suelo y profundidad. Se probaron BHS diarios con agotamiento exponencial y directo de la reserva, utilizando la evapotranspiración de referencia de Penman-Monteith recomendada por FAO. Al mismo tiempo que se disponía de los datos estimados de humedad de suelo mediante diferentes BHS diarios en los tres emplazamientos, también se realizó una monitorización de la humedad del suelo “in situ” mediante el método gravimétrico, con adaptación de dicha metodología a la problemática de cada suelo, para determinar en cada fecha tanto la humedad del suelo como su contenido de AD para una profundidad de 0 a 30 cm. Se tomaron en cada fecha de muestreo 5 muestras para la profundidad 0- 10 cm, otras cinco para 10-20 cm y otras cinco para 20-30 cm, realizándose el correspondiente tratamiento estadístico de los datos. El ADT se calculó a partir de los datos de capacidad de campo y punto de marchitez obtenidos en laboratorio con membrana de Richards. Los resultados de esta primera fase permitieron conocer que el BHS exponencial diario era el que mejor estimaba el AD en Guadalajara considerando la capacidad de campo a una presión de 33 kPa, mientras que en Colmenar se debían considerar para un mejor ajuste, 10 kPa en lugar de 33 kPa. En el observatorio de Radiosondeo debido a que en cada fecha de muestreo la profundidad en la que aparecía el horizonte Bt era diferente, no se pudo demostrar si el BHS exponencial diario tenía un buen comportamiento. En una segunda fase de experimentación (2009-2012) y con el objeto de aminorar los problemas encontrados en Radiosondeo para la medida de humedad del suelo por el método gravimétrico, se procedió a la instalación y utilización de diferentes sensores de medida de humedad de suelo en el mismo observatorio: TDR (time domain reflectometry - TRIME T3 de IMKO); FDR capacitivo (frecuency domain reflectometry - ECH2O EC-20 de DECAGON) y otros. Esta segunda fase de experimentación tuvo una duración de 4 años y se compararon las medidas de humedad de suelo obtenidas a partir de los sensores con las estimadas del BHS exponencial hasta una profundidad de 0 a 85 cm. En laboratorio se realizaron calibraciones específicas de los sensores TDR y FDR para cada uno de los horizontes más diferenciados del Haploxeralf Típico, utilizando diferentes tipos de regresión. Los valores de humedad de suelo con el equipo TDR, corregidos mediante la calibración específica de laboratorio, fueron los que más se ajustaron a las medidas realizadas por método gravimétrico “in situ”, por lo que se utilizó el TDR para las comparaciones con los valores obtenidos del BHS exponencial diario durante los cuatro años de esta segunda fase experimental. Se realizaron diferentes estimaciones del ADT, partiendo de datos de laboratorio y/o de datos procedentes de humedad de los sensores en campo. Los resultados mostraron de nuevo la conveniencia de utilizar el BHS exponencial diario, pero en este caso, con la estimación del ADT realizada a partir de las gráficas de los sensores. Mediante la utilización de los datos de humedad del BHS exponencial diario se han realizado comparaciones con el mismo tipo de balance pero utilizando un periodo semanal o mensual en lugar de diario, para conocer las diferencias. Los valores obtenidos con periodicidad mensual han dado valores de AD inferiores a los balances calculados semanalmente o diariamente. Por último se ha comprobado que los resultados de un BHS exponencial diario pueden complementar la información que se obtiene del Índice de Precipitación Estandarizado (SPI) y pueden mejorar el estudio de la sequía agrícola. ABSTRACT Due to the importance of a better knowledge of soil water at real time and in a more precisely way, this research work has being carried out with the main objective of selecting a daily Soil Water Balance (SWB) to estimate soil water content, and validate it in comparison to “in situ” measurements. Three locations, differing in soil and climate characteristics, were selected in central Spain in order to estimate with certain acuity soil water as plant-Available Water (AW) and to serve as a tool for the climatic studies. The selected places near meteorology stations were: Guadalajara/El Serranillo an alluvium of the Henares watershed; Colmenar Viejo/Base Famet, in the south raised area of the Guadarrama river basin, over metamorphic rocks; and Radiosondeo/Madrid (Barajas) in coarse arkosic sandstone. Morphology characterization, physical, chemical and hydrologic soil properties were studied in each area. In Guadalajara the soil is a Typic Xerorthent with a (Ap-AC-C1- C2) genetic horizon sequence, loam-sandy to loam textural class, less than 2% of rock fragments, presence of equivalent CaCO3 through the whole profile, outstanding the vertical and horizontal homogeneity of the properties. In Colmenar the soil is represented by a Dystric Xerorthent with a (A-C-C/R) genetic horizon sequence, the C/R is 20-30 cm deep where rock outcrops are approximately at 30 cm; a characteristic feature of this profile is its high acidity and high rock fragments content. In Radiosondeo the soil is represented by a Typic Haploxeralf, with the usual alfisol genetic horizon sequence (A-Bt1-Bt2-C/Bt); outstanding its horizontal heterogeneity, “the variability of the Bt (clay enriched horizon) depth in short distances”. In a first experimental stage (2007-2008), the daily SWB chosen was that which only uses as input data the information from the meteorology variables and plant-Total Available Water (TAW) for each soil type and depth. Different daily SWB (with exponential or direct plant-Available Water depletion) were applied, using the Penman- Monteith reference evapotranspiration (ETo) recommended by FAO. At the same time as soil water content was estimated from the different daily SWB at the three locations, also soil water content was being monitored by “in situ” gravimetric methodology, adapting it to each soil characteristic, to determine every time soil water content and AW to a depth of 0 to 30 cm. In each sampling date, 5 samples for each depth were taken: 0-10 cm; 10-20 cm and 20-30 cm and the data were submitted to the corresponding statistical analysis. The TAW was calculated based on field capacity (FC) and permanent wilting point (PWP) data obtained from laboratory by the Richards pressure plate. Results from this first experimental stage show that the daily exponential SWB was the one which better estimated the AW in Guadalajara considering field capacity at -33 kPa, though in Colmenar, field capacity at -10 kPa must be considered instead of -33 kPa for a better estimation. In Radiosondeo due to the fact that the Bt horizon depth varied in different sampling dates, it could not be established if the daily exponential SWB had a good performance. In a second experimental stage (20019-2012) and with the objective of minimizing the problems encountered in Radiosondeo for measuring “in situ” soil water content by the gravimetric method, the installation of different sensors for measuring soil water content were established and used in the same field location: TDR (time domain reflectometry - TRIME T3 from IMKO), capacitance FDR (frecuency domain reflectometry - ECH2O EC-20 from DECAGON) and others. This second experimental stage lasted 4 years in order to compare the soil water measures from the sensors with the estimations by the exponential SWB form 0 to 85 cm soil depths. At laboratory, specific calibrations for TDR and FDR sensors of the Typic Haploxeralf more differentiated horizons were done using different types of regressions. The results showed that soil water data obtained by the TDR equipment, corrected by the specific laboratory calibration, best fitted to “in situ” gravimetric soil water measures. In this way TDR was used for comparing to the daily exponential SWB during the four years of this second experimentation stage. Various estimations for obtaining TAW were tested; based on laboratory data – and/or on the data obtained of the soil water content field sensors. Results confirmed again, the convenience of using the daily exponential SWB, though in this case, with the TAW obtained from the field sensors graphics. Soil water estimated by exponential SWB on daily basis was compared to weekly and monthly periods, in order to know their reliability. The results obtained for a monthly period gave less AW than the ones obtained in a weekly or daily period. Finally it has been proved that the results obtained from the exponential SWB in a daily bases can be used as a useful tool in order to give complementary information to the SPI (Precipitation Standardized Index) and to help in agricultural drought studies.

Nueva tecnología para la separación de gases atmosféricos y captura de dióxido de carbono por aplicación de campos electromagnéticos y fotoionización

Son numerosos los expertos que predicen que hasta pasado 2050 no se utilizarán masivamente las energías de origen renovable, y que por tanto se mantendrá la emisión de dióxido de carbono de forma incontrolada. Entre tanto, y previendo que este tipo de uso se mantenga hasta un horizonte temporal aún más lejano, la captura, concentración y secuestro o reutilización de dióxido de carbono es y será una de las principales soluciones a implantar para paliar el problema medioambiental causado. Sin embargo, las tecnologías existentes y en desarrollo de captura y concentración de este tipo de gas, presentan dos limitaciones: las grandes cantidades de energía que consumen y los grandes volúmenes de sustancias potencialmente dañinas para el medioambiente que producen durante su funcionamiento. Ambas razones hacen que no sean atractivas para su implantación y uso de forma extensiva. La solución planteada en la presente tesis doctoral se caracteriza por la ausencia de residuos producidos en la operación de captura y concentración del dióxido de carbono, por no utilizar substancias químicas y físicas habituales en las técnicas actuales, por disminuir los consumos energéticos al carecer de sistemas móviles y por evitar la regeneración química y física de los materiales utilizados en la actualidad. Así mismo, plantea grandes retos a futuras innovaciones sobre la idea propuesta que busquen fundamentalmente la disminución de la energía utilizada durante su funcionamiento y la optimización de sus componentes principales. Para conseguir el objetivo antes citado, la presente tesis doctoral, una vez establecido el planteamiento del problema al que se busca solución (capítulo 1), del estudio de las técnicas de separación de gases atmosféricos utilizadas en la actualidad, así como del de los sistemas fundamentales de las instalaciones de captura y concentración del dióxido de carbono (capítulo 2) y tras una definición del marco conceptual y teórico (capítulo 3), aborda el diseño de un prototipo de ionización fotónica de los gases atmosféricos para su posterior separación electrostática, a partir del estudio, adaptación y mejora del funcionamiento de los sistemas de espectrometría de masas. Se diseñarán y desarrollarán los sistemas básicos de fotoionización, mediante el uso de fuentes de fotones coherentes, y los de separación electrostática (capítulo 4), en que se basa el funcionamiento de este sistema de separación de gases atmosféricos y de captura y concentración de dióxido de carbono para construir un prototipo a nivel laboratorio. Posteriormente, en el capítulo 5, serán probados utilizando una matriz experimental que cubra los rangos de funcionamiento previstos y aporte suficientes datos experimentales para corregir y desarrollar el marco teórico real, y con los que se pueda establecer y corregir un modelo físico– matemático de simulación (capítulo 6) aplicable a la unidad en su conjunto. Finalmente, debido a la utilización de unidades de ionización fotónica, sistemas láseres intensos y sistemas eléctricos de gran potencia, es preciso analizar el riesgo biológico a las personas y al medioambiente debido al impacto de la radiación electromagnética producida (capítulo 7), minimizando su impacto y cumpliendo con la legislación vigente. En el capítulo 8 se planteará un diseño escalable a tamaño piloto de la nueva tecnología propuesta y sus principales modos de funcionamiento, así como un análisis de viabilidad económica. Como consecuencia de la tesis doctoral propuesta y del desarrollo de la unidad de separación atmosférica y de captura y concentración de dióxido de carbono, surgen diversas posibilidades de estudio que pueden ser objeto de nuevas tesis doctorales y de futuros desarrollos de ingeniería. El capítulo 9 tratará de incidir en estos aspectos indicando líneas de investigación para futuras tesis y desarrollos industriales. ABSTRACT A large number of experts predict that until at least 2050 renewable energy sources will not be massively used, and for that reason, current Primary Energy sources based on extensive use of fossil fuel will be used maintaining out of control emissions, Carbon Dioxide above all. Meanwhile, under this scenario and considering its extension until at least 2050, Carbon Capture, Concentration, Storage and/or Reuse is and will be one of the main solutions to minimise Greenhouse Gasses environmental effect. But, current Carbon Capture and Storage technology state of development has two main problems: it is a too large energy consuming technology and during normal use it produces a large volume of environmentally dangerous substances. Both reasons are limiting its development and its extensive use. This Ph Degree Thesis document proposes a solution to get the expected effect using a new atmospheric gasses separation system with the following characteristics: absence of wastes produced, it needs no chemical and/or physical substances during its operation, it reduces to minimum the internal energy consumptions due to absence of mobile equipment and it does not need any chemical and/or physical regeneration of substances. This system is beyond the State of the Art of current technology development. Additionally, the proposed solution raises huge challenges for future innovations of the proposed idea finding radical reduction of internal energy consumption during functioning, as well as regarding optimisation of main components, systems and modes of operation. To achieve this target, once established the main problem, main challenge and potential solving solutions (Chapter 1), it is established an initial starting point fixing the Atmospheric Gasses Separation and Carbon Capture and Storage developments (Chapter 2), as well as it will be defined the theoretical and basic model, including existing and potential new governing laws and mathematical formulas to control its system functioning (Chapter 3), this document will deal with the design of an installation of an operating system based on photonic ionization of atmospheric gasses to be separated in a later separation system based on the application of electrostatic fields. It will be developed a basic atmospheric gasses ionization prototype based on intense radioactive sources capable to ionize gasses by coherent photonic radiation, and a basic design of electrostatic separation system (Chapter 4). Both basic designs are the core of the proposed technology that separates Atmospheric Gasses and captures and concentrates Carbon Dioxide. Chapter 5 will includes experimental results obtained from an experimental testing matrix covering expected prototype functioning regimes. With the obtained experimental data, theoretical model will be corrected and improved to act as the real physical and mathematical model capable to simulate real system function (Chapter 6). Finally, it is necessary to assess potential biological risk to public and environment due to the proposed use of units of intense energy photonic ionization, by laser beams or by non–coherent sources and large electromagnetic systems with high energy consumption. It is necessary to know the impact in terms of and electromagnetic radiation taking into account National Legislation (Chapter 7). On Chapter 8, an up scaled pilot plant will be established covering main functioning modes and an economic feasibility assessment. As a consequence of this PhD Thesis, a new field of potential researches and new PhD Thesis are opened, as well as future engineering and industrial developments (Chapter 9).

The effect of scour protections in offshore wind farms

The installation of offshore scour protection systems in offshore wind farms allows avoid the effect of scour phenomenon around these structures. Up to date, numerous research projects have been carried out to justify the necessity of the scour protection systems and also to optimize their design. Protection systems based on riprap is frequently used due to its low cost and easy availability compared to other solutions such as geotextile bags or prefabricated concrete blocks. The sizing of these structures can be performed according to a series of recommendations that can optimize the costs associated with them, but there have been only few studies with real data up to now which have allowed identify the need for such protections. This investigation aims to assess the functionality of the scour protections adopted through the available data about their characteristics and the scour depth developed around the foundations. In this sense, this paper presents the results of a study that analyzes the functionality of scour protections in different European offshore wind farms.

Effectiveness of improved cookstoves to reduce indoor air pollution in developing countries. The case of the Cassamance Natural Subregion, Western Africa

The Spanish NGO "Alianza por la Solidaridad" has installed improved cookstoves in 3000 households during 2012 and 2013 to improve energy efficiency reducing fuelwood consumption and to improve indoor air quality. The type of cookstoves were Noflaye Jeeg and Noflaye Jaboot and were installed in the Cassamance Natural Subregion covering part of Senegal, The Gambia and Guinea-Bissau. The Technical University of Madrid (UPM) has conducted a field study on a sample of these households to assess the effect of improved cookstoves on kitchen air quality. Measurements of carbon monoxide (CO) and fine particle matter (PM2.5) were taken for 24-hr period before and after the installation of improved cookstoves. The 24-hr mean CO concentrations were lower than the World Health Organization (WHO) guidelines for Guinea-Bissau but higher for Senegal and Gambia, even after the installation of improved cookstoves. As for PM2.5 concentrations, 24-hr mean were always higher than these guidelines. However, improved cookstoves produced significant reductions on 24-hr mean CO and PM2.5 concentrations in Senegal and for mean and maximum PM2.5 concentration on Gambia. Although this variability needs to be explained by further research to determine which other factors could affect indoor air pollution, the study provided a better understanding of the problem and envisaged alternatives to be implemented in future phases of the NGO project.

A proposal for pellet production from residual woody biomass in the island of Majorca (Spain)

The use of residual biomass for energy purposes is of great interest in isolated areas like Majorca for waste reduction, energy sufficiency and renewable energies development. In addition, densification processes lead to easy-to-automate solid biofuels which additionally have higher energy density. The present study aims at (i) the estimation of the potential of residual biomass from woody crops as well as from agri-food and wood industries in Majorca, and (ii) the analysis of the optimal location of potential pellet plants by means of a GIS approach (location-allocation analysis) and a cost evaluation of the pellets production chain. The residual biomass potential from woody crops in Majorca Island was estimated at 35,874 metric tons dry matter (t DM) per year, while the wood and agri-food industries produced annually 21,494 t DM and 2717 t DM, respectively. Thus, there would be enough resource available for the installation of 10 pellet plants of 6400 t·year−1 capacity. These plants were optimally located throughout the island of Mallorca with a maximum threshold distance of 28 km for biomass transport from the production points. Values found for the biomass cost at the pellet plant ranged between 57.1 €·t−1 and 63.4 €·t−1 for biomass transport distance of 10 and 28 km. The cost of pelleting amounted to 56.7 €·t−1; adding the concepts of business fee, pellet transport and profit margin (15%), the total cost of pelleting was estimated at 116.6 €·t−1. The present study provides a proposal for pellet production from residual woody biomass that would supply up to 2.8% of the primary energy consumed by the domestic and services sector in the Balearic Islands.