Medida del ruido ambiental en el CEIS. Análisis y evaluación de los datos

El presente documento, evalúa y analiza el ruido existente en las inmediaciones del CEIS (Centro Estudio, Innovación y Servicios), situado en la carretera Villaviciosa de Odón a Móstoles (M-856) en el Km 1,5. El objetivo es obtener datos de nivel de ruido en función del tiempo para conocer su variabilidad a lo largo de la semana, para promover una intercomparación entre laboratorios con ruido real. La zona que contempla el proyecto tiene variedad de ruido medioambiental: ruido de tráfico rodado, ruido industrial, ruido de instalaciones y ruido de tráfico aéreo. Estas fuentes de ruido pueden presentarse en diversas combinaciones. Para el ruido total existente, se analiza por un lado el ruido específico de la carretera M-856, y por otro lado el ruido residual asociado a sucesos aislados, como el ruido de tráfico aéreo, ruido industrial y de instalaciones. Para el cálculo de los niveles sonoros de la zona se realiza una evaluación del índice de ruido Ld, para el periodo de día, utilizando como herramienta de cálculo el programa CadnaA versión 4.2. Se realiza la validación de los niveles sonoros obtenidos en el CadnaA en las inmediaciones de la carretera Villaviciosa de Odón a Móstoles. Para ello se comparan los niveles obtenidos en el modelo acústico de la zona elaborado mediante CadnaA y los niveles medidos “in-situ”. Una vez obtenidos los niveles sonoros, se calcula la incertidumbre de las medidas ejecutadas “in-situ” en la última jornada de mediciones realizada, correspondientes a niveles de presión sonora continuos equivalente ponderado A (LAeq, 5min) y de las medidas simuladas en CadnaA , teniendo en cuenta las posibles desviaciones ocasionadas por el equipo de medida, condiciones meteorológicas, variaciones del tráfico, metodología de ensayo..... Por último se valoran los datos obtenidos y se evalúa la posibilidad de promover una intercomparación entre laboratorios realizada con el ruido real de tráfico de la zona. ABSTRACT. The next document evaluates the noise in sorrounding areas of CEIS (Centro Estudio, Innovación y Servicios), located in the road from Villaviciosa de Odón to Móstoles (M-856), in 1.5 km. The aim of this project is to get precise information during time to promove an intercomparation between laboratories with real noise. The area included in the project has several environmental noise: traffic noise, industrial noise and air traffic noise. These noise sources can be combined in different ways. The specific noise of the M-856 on one hand, and the residual noise associated with air traffic noise and industrial noise on the other. The calculation tool CadnaA, 4.2 version, simulates sound levels for the day period and the index Ld. The validation of sound levels around the road Villaviciosa de Odon to Móstoles, is made by comparing the obtained levels in the acoustic model and the real measured levels “in situ” . The uncertainty of the measures "in-situ", and the uncertainty of the sound levels simulated in the acoustic model CadnaA, is calculated using the measurements “in situ” (LAeq, 5min) of the last day. For that calculation, is necessary to take into account the deviations resulting from the measurement equipment, weather conditions, traffic variations, test methodology.... Finally the obtained data are evaluated, considering the possibility of promote an intercomparison between laboratories with real traffic noise of the area.

Evaluación de ruido ambiental en las zonas de uso residencial ubicadas en la zona de influencia de la Avenida San Pablo (Barrio de la Estación, Coslada)

El presente documento analiza y evalúa el ruido ambiental existente en las zonas de uso residencial ubicadas en el Barrio de “La Estación”, en el entorno de la Avenida San Pablo, pertenecientes al municipio de Coslada (Madrid). La zona que contempla el proyecto es muy completa, ya que en ella están presentes diferentes tipos de ruido medioambiental (tráfico ferroviario, tráfico rodado, tráfico aeroportuario, ruido industrial de instalaciones, ruido de actividades, etc), donde las fuentes de ruido pueden manifestarse aisladas o en diversas combinaciones. Para evaluar el ruido total existente, se analiza por un lado el ruido residual de la zona de estudio, y por otro el ruido específico e intermitente asociado a sucesos aislados, como son el ruido de aviones y el ruido de trenes, donde se estudia individualmente la existencia de componentes de tonalidad, baja frecuencia e impulsividad. Una vez obtenidos los niveles de ruido total y ruido residual en la zona objeto de estudio, el índice Nivel de presión sonora promedio LPm de las muestras analizadas, estima correctamente los niveles obtenidos en el muestreo de larga duración. En las medidas realizadas se detecta la existencia de componentes de tonalidad y baja frecuencia en los pasos de aviones y trenes registrados. Se calculan los niveles sonoros existentes en la zona de estudio. Para ello se realiza una evaluación de los índices de ruido Ld, para el periodo día, y Le, para el periodo tarde, utilizando como herramienta de cálculo el programa IMMI 6.3.1e. Se realiza la validación del mapa de niveles sonoros obtenido con el IMMI 6.3.1e. Para ello se hace una comparación entre los niveles calculados con el modelo, y los niveles medidos “in situ” en los puntos de muestreo. Por último se obtiene la incertidumbre en cada una de las medidas ejecutadas en una segunda campaña “in situ”, correspondientes a niveles de presión sonora continuos equivalentes ponderado A (LAeq,5min), teniendo en cuenta las posibles desviaciones ocasionadas por el equipo de medida, condiciones meteorológicas, procedimiento de realización del ensayo, etc. ABSTRACT. The present document analyzes and evaluates the environmental noise in the residential areas located at “La Estación” district, near the San Pablo Avenue, in the Coslada municipality (Madrid). The area considered in this project is very complete, once it covers different types of environmental noise (railway traffic, vehicular traffic, airport traffic, industrial noise of building systems, activities noise, etc), where noise sources may appear isolated or under several combinations. In order to evaluate the existing total noise, on one hand it is analyzed the residual noise in the study area, and on the other hand it is analyzed the specific and intermittent noise associated to isolated occurrences, such as the noise of the aircrafts and the noise of the trains, where the existence of components of tonality, low frequency and impulsiveness is studied individually. After obtaining the levels of total noise and residual noise in the target study area, the sound pressure level average index (LPm) of the analyzed samples estimates correctly the levels obtained in the sampling of long duration. On what concerns the measures carried out, it is detected the existence of components of tonality and low frequency in the registered aircrafts and trains passage. The sound levels of the study area are calculated. For that it is made a valuation of the Ld noise ratio, concerning the day period, and Le, concerning the afternoon period. The calculation tool used is the IMMI 6.3.1e programme. The validation of the map of sound levels obtained with the IMMI 6.3.1e is made. In order to get this validation, it is made a comparison between the levels calculated with the model and the levels measured “in situ” in the sampling points. Finally the uncertainty is obtained in each one of the measurements made in a second sampling “in situ”, correspondent to equivalent A-weighted continuous sound pressure level (LAeq,5 min), having in mind the possible deviations caused by the equipment of measure, meteorological conditions, essay’s execution procedures, etc.

E-comparisons: A new approach to round robin tests for environmental noise assessment in transport infrastructures

The increasing importance of pollutant noise has led to the creation of many new noise testing laboratories in recent years. For this reason and due to the legal implications that noise reporting may have, it is necessary to create procedures intended to guarantee the quality of the testing and its results. For instance, the ISO/IEC standard 17025:2005 specifies general requirements for the competence of testing laboratories. In this standard, interlaboratory comparisons are one of the main measures that must be applied to guarantee the quality of laboratories when applying specific methodologies for testing. In the specific case of environmental noise, round robin tests are usually difficult to design, as it is difficult to find scenarios that can be available and controlled while the participants carry out the measurements. Monitoring and controlling the factors that can influence the measurements (source emissions, propagation, background noise…) is not usually affordable, so the most extended solution is to create very effortless scenarios, where most of the factors that can have an influence on the results are excluded (sampling, processing of results, background noise, source detection…) The new approach described in this paper only requires the organizer to make actual measurements (or prepare virtual ones). Applying and interpreting a common reference document (standard, regulation…), the participants must analyze these input data independently to provide the results, which will be compared among the participants. The measurement costs are severely reduced for the participants, there is no need to monitor the scenario conditions, and almost any relevant factor can be included in this methodology

Self-adaptive grids for noise mapping refinement

Noise maps are usually represented as contour or isolines maps describing the sound levels in a region. Using this kind of representation the user can easily find the noise level assigned to every location in the map. But the acoustic calculations behind the map are not performed for every single location on it; they are only performed in a grid of receivers. The results in this calculation grid are interpolated to draw the isolines or contours. Therefore, the resolution of the calculation grid and the way it was created (rectangular, triangulated, random…) have an effect on the resulting map. In this paper we describe a smart iterative procedure to optimize the quality of the map at a really low additional computational cost, using self-adaptive grids for the acoustic calculations. These self-adaptive grids add new receivers to the sampling grid in those locations where they are expected to be more useful, so that the performance at the output of the interpolator is enhanced. Self-adaptive sampling grids can be used for minimizing the overall error of the map (improving its quality), or for reducing calculation times, and can be also applied selectively to target areas or contour lines. This can be done by the user customizing the maximum number of iterations, the number of new receivers for each iteration, the target isolines, the target quality…

Effectiveness of resilient wheels in reducing noise and vibrations

This study focuses on the effectiveness of resilient wheels in reducing railway noise and vibrations, and compares the effectiveness of three types of wheels. The finite elements method has been used to characterise the vibratory behaviour of these wheels. The model has been excited with a realistic spectrum of vertical track irregularities, and a spectral analysis has been carried out. Results have been post-processed in order to estimate the sound power emitted. These calculations have been used to assess the effectiveness of the resilient wheel designs in reducing noise emitted to the environment and in propagating structural vibrations.

Comparison of vibration and rolling noise emission of resilient and solid monobloc railway wheels in underground lines

Flat or worn wheels rolling on rough or corrugated tracks can provoke airborne noise and ground-borne vibration, which can be a serious concern for nearby neighbours of urban rail transit lines. Among the various treatments used to reduce vibration and noise, resilient wheels play an important role. In conventional resilient wheels, a slightly prestressed V­shaped rubber ring is mounted between the steel wheel centre and tyre. The elastic layer enhances rolling noise and vibration suppression, as well as impact reduction on the track. In this paper the effectiveness of resilient wheels in underground lines, in comparison to monobloc ones, is assessed. The analysed resilient wheel is able to carry greater loads than standard resilient wheels used for light vehicles. It also presents a greater radial resiliency and a higher axial stiffness than conventional V­wheels. The finite element method was used in this study. A quarter car model was defined, in which the wheelset was modelled as an elastic body. Several simulations were performed in order to assess the vibrational behaviour of elastic wheels, including modal, harmonic and random vibration analysis, the latter allowing the introduction of realistic vertical track irregularities, as well as the influence of the running speed. Due to numerical problems some simplifications were needed. Parametric variations were also performed, in which the sensitivity of the whole system to variations of rubber prestress and Poisson’s ratio of the elastic material was assessed.Results are presented in the frequency domain, showing a better performance of the resilient wheels for frequencies over 200 Hz. This result reveals the ability of the analyzed design to mitigate rolling noise, but not structural vibrations, which are primarily found in the lower frequency range.

Using array based techniques for noise source identification in cars

Una de las principales causas del ruido en nuestras ciudades es el tráfico rodado. El ruido generado por los vehículos no es sólo debido al motor, sino que existen diversas fuentes de ruido en los mismos, entre las que se puede destacar el ruido de rodadura. Para localizar las causas del ruido e identificar las principales fuentes del mismo se han utilizado en diversos estudios las técnicas de coherencia y las técnicas basadas en arrays. Sin embargo, en la bibliografía existente, no es habitual encontrar el uso de estas técnicas en el sector automovilístico. En esta tesis se parte de la premisa de la posibilidad de usar estas técnicas de medida en coches, para demostrar a la largo de la misma su factibilidad y su bondad para evaluar las fuentes de ruido en dos condiciones distintas: cuando el coche está parado y cuando está en movimiento. Como técnica de coherencia se elige la de Intensidad Selectiva, utilizándose la misma para evaluar la coherencia existente entre el ruido que llega a los oídos del conductor y la intensidad radiada por distintos puntos del motor. Para la localización de fuentes de ruido, las técnicas basadas en array son las que mejores resultados ofrecen. Statistically Optimized Near-field Acoustical Holography (SONAH) es la técnica elegida para la localización y caracterización de las fuentes de ruido en el motor a baja frecuencia. En cambio, Beamforming es la técnica seleccionada para el caso de media-alta frecuencia y para la evaluación de las fuentes de ruido cuando el coche se encuentra en movimiento. Las técnicas propuestas no sólo pueden utilizarse en medidas reales, sino que además proporcionan abundante información y frecen una gran versatilidad a la hora de caracterizar fuentes de ruido. ABSTRACT One of the most important noise causes in our cities is the traffic. The noise generated by the vehicles is not only due to the engine, but there are some other noise sources. Among them the tyre/road noise can be highlighted. Coherence and array based techniques have been used in some research to locate the noise causes and identify the main noise sources. Nevertheless, it is not usual in the literature to find the application of this kind of techniques in the car sector. This Thesis starts taking into account the possibility of using this kind of measurement techniques in cars, to demonstrate their feasability and their quality to evaluate the noise sources under two different conditions: when the car is stopped and when it is in movement. Selective Intensity was chosen as coherence technique, evaluating the coherence between the noise in the driver’s ears and the intensity radiated in different points of the engine. Array based techniques carry out the best results to noise source location. Statistically Optimized Near-field Acoustical Holography (SONAH) is the measurement technique chosen for noise source location and characterization in the engine at low frequency. On the other hand, Beamforming is the technique chosen in the case of medium-high frequency and to characterize the noise sources when the car is in movement. The proposed techniques not only can be used in actual measurements, but also provide a lot of information and are very versatile to noise source characterization.

A clustering technique for partial discharge and noise sources identification in power cables by means of waveform parameters

On-line partial discharge (PD) measurements have become a common technique for assessing the insulation condition of installed high voltage (HV) insulated cables. When on-line tests are performed in noisy environments, or when more than one source of pulse-shaped signals are present in a cable system, it is difficult to perform accurate diagnoses. In these cases, an adequate selection of the non-conventional measuring technique and the implementation of effective signal processing tools are essential for a correct evaluation of the insulation degradation. Once a specific noise rejection filter is applied, many signals can be identified as potential PD pulses, therefore, a classification tool to discriminate the PD sources involved is required. This paper proposes an efficient method for the classification of PD signals and pulse-type noise interferences measured in power cables with HFCT sensors. By using a signal feature generation algorithm, representative parameters associated to the waveform of each pulse acquired are calculated so that they can be separated in different clusters. The efficiency of the clustering technique proposed is demonstrated through an example with three different PD sources and several pulse-shaped interferences measured simultaneously in a cable system with a high frequency current transformer (HFCT).