The influence of sensor placement on in-situ ultrasound wave velocity measurement.

Ultrasound wave velocity was measured in 30 pieces of Spanish Scots pine (Pinus sylvestris L.), 90 x 140 mm in cross-section and 4 m long. Five different sensor placement arrangements were used: end to end (V0), face to opposite face, edge to opposite edge, face to same face and edge to same edge. The pieces were successively shortened to 3, 2 and 1 m, in order to obtain these velocities and their ratios to reference value V0 for different lengths and angles with respect to the piece axis for the crossed measurements. The velocity obtained in crossed measurements is lower than V0. A correction coefficient for crossed velocities is proposed, depending on the angle, to adjust them to the V0 benchmark. The velocities measured on a surface, are also lower than V0, and their ratio with respect to V0 is close to 0.97 for distances equal to or greater than 18 times the depth of the beam.

In situ surveillance of capacitive pressure transmitter dynamic poles

In this work, a methodology is proposed to find the dynamic poles of a capacitive pressure transmitter in order to enhance and extend the online surveillance of this type of sensor based on the response time measurement by applying noise analysis techniques and the dynamic data system procedure. Several measurements taken from a pressurized water reactor have been analyzed. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamic poles. Nevertheless, the signals that have been analyzed could not be filtered properly in order to remove the plant noise; thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate online sensor surveillance since the previous methods were achieved by considering one real pole only.

AR modelling and DDS for in situ surveillance of capacitive pressure transmitters

In this work, a methodology is proposed to find the dynamics poles of a capacitive pressure transmitter in order to enhance and extend the on line surveillance of this type of sensors based on the response time measurement by applying noise analysis techniques and the Dynamic Data System. Several measurements have been analyzed taken from a Pressurized Water Reactor. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamics poles. Nevertheless, the signals that have been analyzed, could not be filtered properly in order to remove the plant noise, thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate on line sensor surveillance since the previous methods were achieved by considering one real pole only.

Diseño de laboratorio para la evaluación de silenciadores "in situ"

Se ha realizado el diseño de un sistema que permite realizar ensayos de silenciadores “in situ”. Para evaluar el comportamiento del sistema de ensayo de silenciadores se procede a caracterizar los paneles acústicos que son la base del sistema. De los paneles empleados en el sistema, se determinará por diferencia del nivel de presión sonora, el aislamiento a ruido aéreo de los mismos, partiendo del promedio de las medidas obtenidas en la sala emisora de la cámara reverberante con el material instalado y en la sala receptora. Se realizan distintas medidas de los niveles de presión sonora en sala emisora de la cámara reverberante y en la receptora así como del tiempo de reverberación con los paneles instalados en el hueco existente en el elemento de separación vertical de la cámara. Una vez ensayados los paneles, se ha procedido a medir los niveles de presión sonora que se obtienen antes y después de la interposición de distintos silenciadores en el sistema diseñado con el propósito de disponer de un laboratorio de medida de la atenuación de silenciadores. Para ello, se procede a efectuar el montaje, en la puerta sencilla de la cámara reverberante, de los componentes del sistema diseñado y se realizan mediciones de la atenuación que proporciona la colocación de un silenciador en el sistema y su posterior sustitución por un conducto. La medición de la atenuación del nivel de presión sonora que producen los distintos silenciadores se realiza por pérdidas por inserción, siguiendo las directrices de la Norma UNE-ISO 11820 y por el método de conductos forrados como cálculo teórico. ABSTRACT. A system has been designed for testing silencers “in situ”. In first place, to evaluate the behavior of the system in the test of silencers, it has been proceeded to customize the acoustic panels that are the basis of the system. The attenuation sound of the panels used in the system will be determined by the difference of sound pressure level. It will be made through the average of the measurements obtained in the source room of the reverberant chamber, the average of the measurements obtained in the receiving room, as well as the reverberation time, with the material installed in the hole of the walls. Once the panels are tested, and with the purpose of having a laboratory to measure the attenuation of silencers, the sound pressure levels has been measured before and after inserting the different silencers in the designed system. To obtain these measures, the components of the system designed have been installed in the hollow of the single door of the reverberant chamber and then the sound pressure level has been measured with a silencers first and after with a duct instead of the silencer. The measurement of the attenuation of the sound pressure level produced by different silencers has been made by insertion loss, following the 11820 UNE-ISO, as well as theoretical calculation has been made by the method of duct lined.