Usability Planner: A Tool to Support the Process of Selecting Usability Methods

There is increasing pressure on developers to produce usable systems, which requires the use of appropriate methods to support user centred design during development. There is currently no consistent advice on which methods are appropriate in which circumstances, so the selection of methods relies on individual experience and expertise. Considerable effort is required to collate information from various sources and to understand the applicability of each method in a particular situation. Usability Planner is a tool aimed to support the selection of the most appropriate methods depending on project and organizational constraints. Many of the rules employed are derived from ISO standards, complemented with rules from the authors’ experience.

'Enhancement of the crystallization process of TbxFe1-x thin films upon the formation of alpha-Tb phase'

TbxFe1−x thin films deposited by sputtering on Mo were investigated structurally and magnetically. The microstructure consists of TbFe2 nanoparticles embedded in an amorphous matrix, and the Tb content can be correlated with an increase in the volume of these nanoparticles. Similar microstructure and behavior were found when TbFe2 was deposited on glass and on a Pt buffer layer. Nevertheless, thermal treatments promote a different effect, depending on the mechanical stiffness of the buffer layer. The layers deposited on Mo, a rigid material, show crystalline TbFe2 together with α-Tb phase upon thermal treatment. In contrast, TbFe2 does not crystallize properly on Pt, a material with a lower stiffness than Mo. Intermediate results were observed on the film deposited on glass. Experimental results show the impact of the buffer stiffness on the crystallization process. Moreover, the formation of α-Tb appears to be fundamental to crystallized TbFe2 on layers deposited on rigid buffers

Fabrication process of Mo/Au TES at RT

We report on the fabrication details of TES based on Mo/Au bilayers. The Mo layer is deposited by radio frequency (RF) sputtering and capped with a sputter deposited thin Au protection layer. Afterwards, a second Au layer of suitable (lower) resistivity is deposited ex‐situ by e‐beam evaporation, until completion of the total desired Au thickness. The deposition was performed at room temperature (RT) on LPCVD Si3 N4 membranes. Such a deposition procedure is very reproducible and allow controlling the critical temperature (Tc) and normal electrical resistance (RN ) of the Mo/Au bilayer. The process is optimized to achieve low stress bilayers, thus avoiding the undesirable curvature of the membranes. Bilayers are patterned using photolithographic techniques and wet etching procedures. Mo superconducting paths are used to contact the Mo/Au bilayers, thus ensuring good electrical conductivity and thermal isolation. The entire fabrication process let to stable and reproducible sensors with required and tunable functional properties

Process of Expropriation of Buildings for the Construction of the New Dock of the Port of Cartagena (Spain) in the 18th Century

The need of the Bourbon monarchy to build a Naval Base in the Bay of Cartagena (Spain) during the eighteenth century, implied performing various actions on the environment which allowed the construction of the new dock. One of the priority actions was the transformation of the watershed of the streams that flowed into Mandaraches´s sea. For this reason, a dike was designed and constructed in the northern part of the city. The design of this great work, which was designed as a fortification of the city, was subject to considerable uncertainties. Its proximity to the city involved the demolition of several buildings in the San Roque´s neighborhood. The greater or lesser number of affected buildings and the value of the just indemnification for the expropriation of them, become decisive factors to determine if the work was viable for the Royal Estate or not.

Sentence selection for improving the tuning process of a statistical machine translation system

Este artículo describe una estrategia de selección de frases para hacer el ajuste de un sistema de traducción estadístico basado en el decodificador Moses que traduce del español al inglés. En este trabajo proponemos dos posibilidades para realizar esta selección de las frases del corpus de validación que más se parecen a las frases que queremos traducir (frases de test en lengua origen). Con esta selección podemos obtener unos mejores pesos de los modelos para emplearlos después en el proceso de traducción y, por tanto, mejorar los resultados. Concretamente, con el método de selección basado en la medida de similitud propuesta en este artículo, mejoramos la medida BLEU del 27,17% con el corpus de validación completo al 27,27% seleccionando las frases para el ajuste. Estos resultados se acercan a los del experimento ORACLE: se utilizan las mismas frases de test para hacer el ajuste de los pesos. En este caso, el BLEU obtenido es de 27,51%.

Vibrations loads in the process of designing scientific spacecraft payloads

Scientific missions constitute fundamental cornerstones of space agencies such as ESA and NASA. Modern astronomy could not be understood without the data provided by these missions. Scientists need to design very carefully onboard instruments. Payloads have to survive the crucial launch moment and later perform well in the really harsh space environ-ment. It is very important that the instrument conceptual idea can be engineered to sustain all those loads

Metaphor and Genre: An Approach to improve the learning process of English for Aeronautics

This study suggests a theoretical framework for improving the teaching/ learning process of English employed in the Aeronautical discourse that brings together cognitive learning strategies, Genre Analysis and the Contemporary theory of Metaphor (Lakoff and Johnson 1980; Lakoff 1993). It maintains that cognitive strategies such as imagery, deduction, inference and grouping can be enhanced by means of metaphor and genre awareness in the context of content based approach to language learning. A list of image metaphors and conceptual metaphors which comes from the terminological database METACITEC is provided. The metaphorical terms from the area of Aeronautics have been taken from specialised dictionaries and have been categorised according to the conceptual metaphors they respond to, by establishing the source domains and the target domains, as well as the semantic networks found. This information makes reference to the internal mappings underlying the discourse of aeronautics reflected in five aviation accident case studies which are related to accident reports from the National Transportation Safety Board (NTSB) and provides an important source for designing language teaching tasks. La Lingüística Cognitiva y el Análisis del Género han contribuido a la mejora de la enseñanza de segundas lenguas y, en particular, al desarrollo de la competencia lingüística de los alumnos de inglés para fines específicos. Este trabajo pretende perfeccionar los procesos de enseñanza y el aprendizaje del lenguaje empleado en el discurso aeronáutico por medio de la práctica de estrategias cognitivas y prestando atención a la Teoría del análisis del género y a la Teoría contemporánea de la metáfora (Lakoff y Johnson 1980; Lakoff 1993). Con el propósito de crear recursos didácticos en los que se apliquen estrategias metafóricas, se ha elaborado un listado de metáforas de imagen y de metáforas conceptuales proveniente de la base de datos terminológica META-CITEC. Estos términos se han clasificado de acuerdo con las metáforas conceptuales y de imagen existentes en esta área de conocimiento. Para la enseñanza de este lenguaje de especialidad, se proponen las correspondencias y las proyecciones entre el dominio origen y el dominio meta que se han hallado en los informes de accidentes aéreos tomados de la Junta federal de la Seguridad en el Transporte (NTSB)

Selection, training and validation process of a sensory panel for bread analysis: Influence of cultivar on the quality of breads made from common wheat and spelta wheat

A protocol of selection, training and validation of the members of the panel for bread sensory analysis is proposed to assess the influence of wheat cultivar on the sensory quality of bread. Three cultivars of bread wheat and two cultivars of spelt wheat organically-grown under the same edaphoclimatic conditions were milled and baked using the same milling and baking procedure. Through the use of triangle tests, differences were identified between the five breads. Significant differences were found between the spelt breads and those made with bread wheat for the attributes ?crumb cell homogeneity? and ?crumb elasticity?. Significant differences were also found for the odor and flavor attributes, with the bread made with ?Espelta Navarra? being the most complex, from a sensory point of view. Based on the results of this study, we propose that sensory properties should be considered as breeding criteria for future work on genetic improvement.

La memoria en el proceso creativo de Juan Muñoz = Memory in the creative process of Juan Muñoz

Esta tesis integra un estudio reflexivo sobre la relación de dependencia entre la creación y la memoria a través del análisis de la última obra del escultor Juan Muñoz: Double Bind (Tate Modern, Londres, 2001). Desde esta posición es obligado replantear el análisis de la obra, lo que hace necesario su estudio cubriendo el mayor espectro posible de información accesible más allá de la obra en sí, para aproximarse a la convergencia entre memoria y creación. La perspectiva de análisis propuesta abre camino a nuevas consideraciones so¬bre la relevancia del conocimiento en el desarrollo del proceso creativo. Este análisis no debe tan sólo suponer una aportación al conocimiento del trabajo de Juan Muñoz. Debe también desprenderse de él la innegable participación y necesaria lectura del pasado en el presente. La amnesia de los tiempos pasados impide completar el atlas de imágenes en las que se apoya la creación impidiendo el conocimiento del origen de las fuentes de inspi¬ración y las bases de la creación de una determinada obra. Este hecho limita y distorsiona sus posibles interpretaciones. Pretendo un acercamiento al entendimiento de la forma de mirar y de crear a través del tiempo que es memoria. La memoria tiene un cometido de crucial importancia para la actividad mental y juega un papel fundamental en la conducta y en la creación. La obra es el resultado de la búsqueda de una idea que exprese algo que el creador no puede ex¬presar de otra manera. Es la necesidad de expresar las ideas mediante un lenguaje que se desarrolla en el tiempo y en el espacio, reflejo del ser que responde al pensamiento. Es una forma de experiencia donde subyacen las sendas del pasado y donde se plantea el futuro. Sólo el creador accede a la obra desde dentro, el observador llega a ella desde el exterior y mediante su propia subjetividad. Las obras son formas de experiencia de sus autores, comunicar el mensaje de dicha experiencia supone por tanto interpretar. Persiguiendo la necesidad de saber y entender, pretender explicar el sentido de una cosa implica una apreciación intencionada asociada al entendimiento del intérprete. Las obras son produc¬tos que portan un mensaje y que contienen en su estructura las trazas del tiempo vivido por su creador. Si se quiere adquirir un acercamiento que represente la posición de un autor, será necesario no solo mirar a través de ella, si no introducirse en el contexto de su historia. Mirar hacia atrás, hacia la profundidad del presente para tener conciencia del pensamiento presente y futuro. Recorrer de este modo la instalación Double Bind de Juan Muñoz proporciona una síntesis de sus preocupaciones e intereses a la vez que aporta un conocimiento no necesariamente inmediato, pero relevante y trascendente de la obra, su creador y la historia. ABSTRACT This thesis comprises a reflective study of the dependence relationship between creation and memory through the analysis of the latest work by the sculptor Juan Muñoz: Double Bind (Tate Modern, London, 2001). From this position, it is mandatory to rethink the analysis of the work, making it necessary to cover the widest possible range of information available beyond the work itself, in order to obtain a closer view of the convergence between memory and creation. The proposed analytical approach opens up new considerations on the relevance of knowledge during the development of the creative process. This analysis should not only make a contribution to the knowledge of the work of Juan Muñoz. It should also infer the undeniable involvement and the necessary reading of the past in the present. Amnesia regarding past makes it impossible to complete the atlas of images on which the creation is based, blocking knowledge of the origin of the sources of inspiration and the basis for the creation of a specific work. This fact limits and distorts its possible interpretations. My intention is an approach to how to understand memory as the way of looking and creating over time. Memory has a crucial role to mental activity and plays a key role in behaviour and creation. The work is the result of finding an idea that expresses something that the creator can not express otherwise. It is the need to express ideas by means of a language that develops throughout time and space, a reflection of the being that responds to the thought. It is a way of experience underlying the paths of the past and where the future is set out. Only the creator can access the work from the inside. The observer sees it from the outside and in accordance with his/her own subjectivity. The works form a part of the experience of their authors, thus implying the interpretation of the message of their experience being passed on. The pursuit of knowledge and understanding, and trying to explain the meaning of something implies a deliberate appreciation associated with the understanding of the interpreter. The works are products bearing a message and containing in their structure traces of the time lived by their creator. If one wants to come close to what the author’s posture represents, it will not only be necessary to penetrate it, but also to introduce oneself into the context of its history. Take a look back, towards the depth of the present in order to become aware of present and future thinking. To go across the installation of Double Bind by Juan Muñoz in this way offers a synthesis of his concerns and interests while also providing a not necessarily immediate knowledge, but one which is relevant and important to the work, its creator and history.

Use of infrared thermography as a tool to monitor skin temperature along the recovery process of an anterior cruciate ligament surgery

Infrared thermography (IRT) is a safe and non-invasive tool used for examining physiological functions based on skin temperature (Tsk) control. Thermograms from 25 anterior cruciate ligament (ACL) surgically operated patients (2 female, 23 male) were taken with a FLIR infrared camera according to the protocol established by the International Academy of Clinical Thermology (IACT). This work consists of 4 studies. Studies 1 and 3 were related to establish the probable thermal difference among different moments of an ACL rupture after surgery: before starting the rehabilitation (P0), at the end of rehabilitation (P1) and 18 months from the end of rehabilitation (P2). For this purpose, on the other hand, studies 2 and 4 were related to establish the skin thermal difference (Tsk) between the injured and the non-injured leg in P0, P1 and P2. Results of the first study showed significant temperature increases in the posterior thigh area between P0 and P1 probably due to a compensatory mechanism. According to this, we can conclude that temperature of the posterior area of the injured and noninjured leg has increased from the first to the last day of the rehabilitation process. In the second study we found significant temperature differences between the injured and non-injured leg in both stages of rehabilitation (p<.01). On the one hand, the temperature of the injured leg is higher in the anterior view and the temperature of the non-injured leg is higher in the posterior view. By the time the patients had recovered from the reconstruction, thermal imbalances should have not been shown between symmetrical parts, but differences seemed to be still latent.. Study 3 shows that temperatures seem to be higher after a year and a half (P2) than in P1. Study 4 shows how thermal values 18 months later seemed to be normalized between both legs. No significant differences were found between the injured leg and the noninjured leg after one year and a half of the rehabilitation process. Considering results from Study 3 and 4 we can conclude that patients seemed to have recovered from a thermal point of view. The temperature in P2 was higher but symmetrical. RESUMEN La termografía infrarroja (IRT) es una herramienta segura y no invasiva utilizada para examinar funciones fisiológicas que se basan en el control de temperatura de la piel (Tsk). Termogramas de 25 pacientes intervenidos quirúrgicamente del ligamento cruzado anterior (LCA) (2 mujeres, 23 hombres) fueron tomadas con una cámara de infrarrojos FLIR de acuerdo con el protocolo establecido por la Academia Internacional de Termología Clínica (IACT). Este trabajo consiste en 4 estudios. Los estudios 1 y 3 describen la diferencia térmica entre los diferentes momentos tras la operación del ligamento cruzado anterior: antes de comenzar la rehabilitación (P0), al final de la rehabilitación (P1) y 18 meses tras finalizar la rehabilitación (P2). Por otra parte, los estudios 2 y 4 describen la diferencia de temperatura de la piel (Tsk) entre la pierna lesionada y la pierna no lesionada en P0, P1 y P2. Los resultados del primer estudio mostraron aumentos significativos de temperatura en la zona posterior de los muslos entre P0 y P1, probablemente debido a un mecanismo de compensación. De acuerdo con esto, se puede concluir que la temperatura de la zona posterior de la pierna lesionada y no lesionada se ha incrementado desde el primero hasta el último día del proceso de rehabilitación. En el segundo estudio se encontraron diferencias significativas de temperatura entre la pierna lesionada y no lesionada en ambas etapas de la rehabilitación (p<.01). Por un lado, la temperatura de la pierna lesionada es mayor en la vista anterior. Por otro lado, la temperatura de la pierna no lesionada es mayor en la vista posterior. Una vez que los pacientes se han recuperado de todo el proceso, no deberían existir desequilibrios térmicos entre partes simétricas del cuerpo, pero las diferencias todavía estaban latentes. El tercer estudio muestra que la temperatura es más alta en P2 que en P1. El cuarto estudio muestra cómo los valores térmicos entre ambas piernas en P2 se han normalizado entre ambas piernas. No se encontraron diferencias significativas entre la pierna lesionada y la pierna no lesionada después de 18 meses tras el proceso de rehabilitación. Considerando los resultados del studio 3 y 4, podemos concluir que se ha llegado a la recuperación total desde un punto de vista térmico. La temperatura es más elevada en P2 pero simétrica.

Evaluation of the PV cell operation temperature in the process of fast switching to open-circuit mode

A procedure for measuring the overheating temperature (ΔT ) of a p-n junction area in the structure of photovoltaic (PV) cells converting laser or solar radiations relative to the ambient temperature has been proposed for the conditions of connecting to an electric load. The basis of the procedure is the measurement of the open-circuit voltage (VO C ) during the initial time period after the fast disconnection of the external resistive load. The simultaneous temperature control on an external heated part of a PV module gives the means for determining the value of VO C at ambient temperature. Comparing it with that measured after switching OFF the load makes the calculation of ΔT possible. Calibration data on the VO C = f(T ) dependences for single-junction AlGaAs/GaAs and triple-junction InGaP/GaAs/Ge PV cells are presented. The temperature dynamics in the PV cells has been determined under flash illumination and during fast commutation of the load. Temperature measurements were taken in two cases: converting continuous laser power by single-junction cells and converting solar power by triple-junction cells operating in the concentrator modules.

Mechanical behaviour and formation process of silkworm silk gut

High performance silk fibers were produced directly from the silk glands of silkworms ("Bombyx mori") following an alternative route to natural spinning. This route is based on a traditional procedure that consists of soaking the silk glands in a vinegar solution and stretching them by hand leading to the so called silkworm guts. Here we present, to the authors’ best knowledge, the first comprehensive study on the formation, properties and microstructure of silkworm gut fibers. Comparison of the tensile properties and microstructural organization of the silkworm guts with those of naturally spun fibers allows gain of a deeper insight into the mechanisms that lead to the formation of the fiber, as well as the relationship between the microstructure and properties of these materials. In this regard, it is proved that an acidic environment and subsequent application of tensile stress in the range of 1000 kPa are sufficient conditions for the formation of a silk fiber.

Control de movimientos en presas de hormigón mediante DGPS. Comparación con otros métodos de auscultación e implicaciones para la seguridad. Estudio de caso en la presa de La Aceña (Ávila)

Las normativas que regulan la seguridad de las presas en España han recogido la necesidad de conocer los desplazamientos y deformaciones de sus estructuras y cimientos. A día de hoy, son muchas las presas en explotación que no cuentan con un sistema de auscultación adecuado para controlar este tipo de variables, ya que la instalación de métodos clásicos de precisión en las mismas podría no ser viable técnicamente y, de serlo, supondría un coste económico importante y una dudosa garantía del proceso de ejecución de la obra civil correspondiente. Con el desarrollo de las nuevas tecnologías, la informática y las telecomunicaciones, han surgido nuevos sistemas de auscultación de desplazamientos. Los sistemas GPS actuales, diseñados para el control de estructuras, guiado de maquinaria, navegación y topografía, estabilidad de taludes, subsidencias, etc. permiten alcanzar precisiones centimétricas. El sistema de control de movimientos basado en la tecnología DGPS (GPS diferencial) combinada con un filtro estadístico con el que se alcanzan sensibilidades de hasta ±1 mm en el sistema, suficientes para una auscultación normal de presas según los requerimientos de la normativa actual. Esta exactitud se adapta a los desplazamientos radiales de las presas, donde son muy comunes valores de amplitudes en coronación de hasta 15 mm en las de gravedad y de hasta 45 mm en el caso de las presas bóveda o arco. La presente investigación tiene por objetivo analizar la viabilidad del sistema DGPS en el control de movimientos de presas de hormigón comparando los diferentes sistemas de auscultación y su correlación con las variables físicas y las vinculadas al propio sistema GPS diferencial. Ante la necesidad de dar respuesta a estas preguntas y de validar e incorporar a la mencionada tecnología en la ingeniería civil en España, se ha llevado a cabo un estudio de caso en La Aceña (Ávila). Esta es una de las pocas presas españolas que se está controlando con dicha tecnología y de forma simultánea con los sistemas clásicos de auscultación y algunos otros de reciente aplicación La presente investigación se ha organizado con idea de dar respuesta a varias preguntas que el explotador de presas se plantea y que no se analizan en el estado del arte de la técnica: cómo hacer la configuración espacial del sistema y cuáles son los puntos necesarios que se deben controlar, qué sistemas de comunicaciones son los más fiables, cuáles son los costes asociados, calibración del software, vida útil y mantenimientos requeridos, así como la posibilidad de telecontrolar los datos. Entre las ventajas del sistema DGPS, podemos señalar su bajo coste de implantación y posibilidad de controlarlo de forma remota, así como la exactitud y carácter absoluto de los datos. Además, está especialmente indicado para presas aisladas o mal comunicadas y para aquellas otras en las que el explotador no tiene referencia alguna de la magnitud de los desplazamientos o deformaciones propias de la presa en toda su historia. Entre los inconvenientes de cualquier sistema apoyado en las nuevas tecnologías, destaca la importancia de las telecomunicaciones ya sea en el nivel local en la propia presao desde su ubicación hasta el centro de control de la explotación. Con la experiencia alcanzada en la gestión de la seguridad de presas y sobre la base de la reciente implantación de los nuevos métodos de auscultación descritos, se ha podido analizar cada una de sus ventajas e inconvenientes. En el capítulo 5, se presenta una tabla de decisión para el explotador que servirá como punto de partida para futuras inversiones. El impacto de esta investigación se ha visto reflejado en la publicación de varios artículos en revistas indexadas y en el debate suscitado entre gestores y profesionales del sector en los congresos nacionales e internacionales en los que se han presentado resultados preliminares. All regulations on the safety of dams in Spain have collected the need to know the displacements and deformations of the structure and its foundation. Today there are many dams holding not have an adequate system of auscultation to control variables such as the installation of classical methods of precision in the same might not be technically feasible, and if so, would cost important economic and guarantee the implementation process of the dubious civil works. With the development of new technologies, computing and telecommunications, new displacements auscultation systems have emerged. Current GPS systems designed to control structures, machine guidance, navigation and topography, slope stability, subsidence, etc, allow to reach centimeter-level accuracies. The motion control system based on DGPS technology applies a statistical filter that sensitivities are achieved in the system to ± 1 mm, sufficient for normal auscultation of dams as required by current regulations. This accuracy is adapted to the radial displacement of dams, which are common values in coronation amplitudes up to 15 mm in gravity dams and up to 45 mm in arch or arc dams. This research aims to analyze the feasibility of DGPS system in controlling movements of concrete dams, comparing the different systems auscultation and its correlation with physical variables and linked to differential GPS system itself. Given the need to answer this question and to validate and incorporate this technology to civil engineering in Spain, has conducted a case study in real time at the dam La Aceña (Ávila). This dam is one of the few Spanish companies, which are controlling with this technology and simultaneously with the classic auscultation systems and some other recent application. This research has been organized with a view to responding to questions that the dam operator arises and in the state of the art technique not discussed: how to make spatial configuration of the system and what are the necessary control points what communication systems are the most reliable, what are the associated costs, calibration software, service life and maintenance requirements, possibility of monitoring, etc. Among the advantages we can point to its low cost of implementation, the possibility of remote, high accuracy and absolute nature of the data. It could also be suitable for those isolated or poorly communicated dams and those in which the operator has no reference to the magnitude of displacements or deformations own prey in its history. The disadvantages of any system based on the new technologies we highlight the importance of telecommunications, either locally or from this dam control center of the farm. With the experience gained in the management of dam safety and based on the recent introduction of new methods of auscultation described, it has been possible to analyze each of their advantages and disadvantages. A decision table for the operator, which will serve as a starting point for future investments is presented. The impact of research, has been reflected in the publication of several articles in refereed journals and discussion among managers and professionals in national and international conferences in which they participated.

Application of the Extended Kalman filter to fuzzy modeling: Algorithms and practical implementation

Modeling phase is fundamental both in the analysis process of a dynamic system and the design of a control system. If this phase is in-line is even more critical and the only information of the system comes from input/output data. Some adaptation algorithms for fuzzy system based on extended Kalman filter are presented in this paper, which allows obtaining accurate models without renounce the computational efficiency that characterizes the Kalman filter, and allows its implementation in-line with the process

Guidance for the development of accessibility evaluation tools following the Unified Software Development Process

Automated and semi-automated accessibility evaluation tools are key to streamline the process of accessibility assessment, and ultimately ensure that software products, contents, and services meet accessibility requirements. Different evaluation tools may better fit different needs and concerns, accounting for a variety of corporate and external policies, content types, invocation methods, deployment contexts, exploitation models, intended audiences and goals; and the specific overall process where they are introduced. This has led to the proliferation of many evaluation tools tailored to specific contexts. However, tool creators, who may be not familiar with the realm of accessibility and may be part of a larger project, lack any systematic guidance when facing the implementation of accessibility evaluation functionalities. Herein we present a systematic approach to the development of accessibility evaluation tools, leveraging the different artifacts and activities of a standardized development process model (the Unified Software Development Process), and providing templates of these artifacts tailored to accessibility evaluation tools. The work presented specially considers the work in progress in this area by the W3C/WAI Evaluation and Report Working Group (ERT WG)