Influence of grain size and compaction of different solid fuels on the layer ignition temperature

The results obtained from these analyses provide some clarifications about the thermal behaviour of the products and also enough information to design some prevention measurements in these facilities to avoid or at least minimize the risk of ignition of a dust layer.

Characterization of spontaneous combustuion tendency of dried sewage sludge

The general purpose of this study was the determination of the safety conditions to avoid the presence of explosive atmospheres in the wastewater industry. Eight Spanish plants located in Madrid, Barcelona and Málaga were considered and several sludge samples were taken in different seasons. The base for the assessment of the spontaneous ignition behaviour of dust accumulations is the experimental determination of the self-ignition temperature under isothermal conditions. Self-ignition temperatures at four volumes were obtained for one sample of sewage sludge, allowing their extrapolation to large storage facilities. A simple test method, based also on an isothermal study of samples, is the UN classification of substances liable to spontaneous combustion. Two different samples were so tested, obtaining unlike results if transported in packages of different volumes. By means of thermogravimetric techniques it is possible to analyse the thermal susceptibility of dried sewage sludge. Apparent activation energy can be obtained from the rate of weight loss. It is also applied to the study of self-ignition susceptibility by modifying test conditions when oxygen stream is introduced. As a consequence of this oxidant contribution, sample behaviour can be very different during testing and a step drop or sudden loss of weight is observed at a characteristic temperature for every substance, associated to a rapid combustion. Plotting both the activation energy and the characteristic temperature, a map of self-ignition risk was obtained for 10 samples, showing different risk levels for samples taken in different locations and at different seasons. A prediction of the self-ignition risk level can be also determined.

Determinación de propiedades de inflamabilidad de mezclas para co-combustión

La recuperación de energía a partir de biomasa y residuos no reciclables por la combustión está cobrando una notable importancia actualmente. Una de las técnicas más utilizadas para esta propuesta es la co-combustión de mezclas de residuos y biomasa. Con esta nueva tecnología, mezclas de diferentes materiales han aparecido en las instalaciones industriales y tienen que ser reconocidas como nuevos combustibles, debido a que a sus propiedades son aún desconocidas. Estas propiedades incluyen las energéticas, que son el objetivo del proceso de mezcla, y también las propiedades de inflamabilidad. Residuos y biomasa en forma de polvos tienen propiedades de ignición que se han de tener en cuenta a la hora de diseñar las medidas de prevención y protección en una instalación industrial. El objetivo principal de este estudio es determinar el riesgo de ignición de las mezclas de residuos / biomasa en capas y cómo, mediante la adición de diferentes cantidades de estos materiales, este riesgo puede cambiar. Para desarrollar este estudio, se utiliza la temperatura mínima de ignición en la capa. Tres muestras diferentes han sido analizadas, lodos con secado térmico de depuradora, paja de trigo y virutas de madera, Abstract Energy recovery from biomass and non-recyclable waste products by combustion has become important. One of the most used techniques for this proposal is the co-firing of waste and biomass mixtures, With this new technology, mixtures of different materials have appeared in the industrial facilities and they have to be treated as new fuels because their properties are unknown. Among this properties we include energetic properties that are the objective of the mixing process, and also the ignitability properties. Waste and biomass dusts have ignition properties that have to be taken into account in the design but also in the, prevention and protection process of an industrial facility.. The main objective of this research is to determine the risk of ignition of waste / biomass mixtures layers and how, by adding different quantities of these materials, this risk may vary. To develop this, the minimum ignition temperature on layer is used. Three different samples have been analysed, thermally dried sewage sludge, wheat straw and wood chips.

Determinación del riesgo de incendio en una instalación de secado de alperujo = Determination of the risk of fire in an olive-oil mill waste dryer

For the energy valorization of alperujo, residue of the olive oil two phases extraction process, it is necessary to perform a drying process to reduce moisture content from over 60% to less than 10%. In order to reduce primary energy consumption and get an economic return, usually in this kind of drying facilities Gas Turbine CHP is used as a heat source. There have been recently in Spain some fires in this kind of GT-CHP facilities, which have caused high material losses. In some of these fires it has been suggested that the fire was caused by the output of incandescent alperujo in the flue gasesof the drying system. Therefore, the aim of this study is to determine experimentally and analytically under which operational conditions a process of alperujo self-ignition in the drying process can begin, and determine the actual fire hazard in this type of TG-CHP system. For analytical study, the temperature and initial composition of the combustion gases of the Gas Turbine at the entrance of the drying process was calculated and the gas equilibrium conditions reached in contact with the biomass were calculated and, therefore, the temperature of the biomass during the drying process. Moreover, the layer and dust ignition temperature of alperujo has been experimentally determined, according to EN 50281-2-1: 2000. With these results, the operating conditions of the drying process, in which there are real risk of auto-ignition of alperujo have been established.Para la valorización energética del alperujo, residuo del proceso de extracción en dos fases del aceite de oliva, es necesario realizar un proceso de secado para reducir su contenido de humedad de más del 60% al 10% m/m en b.h. Con el fin de reducir el consumo de energía primaria y obtener una rentabilidad económica, normalmente en este tipo de instalaciones de secado se usa la cogeneración con turbina de gas (TG) como fuente de calor. En España en los últimos años han ocurrido algunos casos de incendio en este tipo de instalaciones de cogeneración, que han supuesto pérdidas materiales muy elevadas. Por esta razón, el objetivo de este trabajo es determinar analítica y experimentalmente las condiciones operativas del secadero bajo las cuales podría comenzar un proceso de autoinflamación del alperujo y determinar el riesgo real de incendio en este tipo de instalaciones. Para el estudio analítico, se ha planteado y validado el modelo matemático que permite calcular la temperatura y la composición de los gases de combustión a la entrada y a la salida del secadero, en función de las curvas características de la TG, de las condiciones atmosféricas, del caudal y del grado de humedad de la biomasa tratada. El modelo permite además calcular la temperatura de bulbo húmedo, que es la máxima temperatura que podría alcanzar la biomasa durante el proceso de secado y determinar la cantidad de biomasa que se puede secar completamente en función del caudal y de las condiciones de entrada de los gases de combustión. Con estos resultados y la temperatura mínima de autoinflamación del alperujo determinada experimentalmente siguiendo la norma EN 50281- 2-1:2000, se demuestra que en un proceso de secado de alperujo en condiciones normales de operación no existe riesgo de autoencendido que pueda dar origen a un incendio.

Ignition conditions for inertial confinement fusion targets with a nuclear spin-polarized DT fuel

The nuclear fusion cross-section is modified when the spins of the interacting nuclei are polarized. In the case of deuterium?tritium it has been theoretically predicted that the nuclear fusion cross-section could be increased by a factor d = 1.5 if all the nuclei were polarized. In inertial confinement fusion this would result in a modification of the required ignition conditions. Using numerical simulations it is found that the required hot-spot temperature and areal density can both be reduced by about 15% for a fully polarized nuclear fuel. Moreover, numerical simulations of a directly driven capsule show that the required laser power and energy to achieve a high gain scale as d-0.6 and d-0.4 respectively, while the maximum achievable energy gain scales as d0.9.

Mechanical and thermal behaviour of isotactic polypropylene reinforced with inorganic fullerene-like WS2 nanoparticles: Effect of filler loading and temperature

The thermal and mechanical behaviour of isotactic polypropylene (iPP) nanocomposites reinforced with different loadings of inorganic fullerene-like tungsten disulfide (IF-WS2) nanoparticles was investigated. The IF-WS2 noticeably enhanced the polymer stiffness and strength, ascribed to their uniform dispersion, the formation of a large nanoparticle?matrix interface combined with a nucleating effect on iPP crystallization. Their reinforcement effect was more pronounced at high temperatures. However, a drop in ductility and toughness was found at higher IF-WS2 concentrations. The tensile behaviour of the nanocomposites was extremely sensitive to the strain rate and temperature, and their yield strength was properly described by the Eyring s equation. The activation energy increased while the activation volume decreased with increasing nanoparticle loading, indicating a reduction in polymer chain motion. The nanoparticles improved the thermomechanical properties of iPP: raised the glass transition and heat deflection temperatures while decreased the coefficient of thermal expansion. The nanocomposites also displayed superior flame retardancy with longer ignition time and reduced peak heat release rate. Further, a gradual rise in thermal conductivity was found with increasing IF-WS2 loading both in the glassy and rubbery states. The results presented herein highlight the benefits and high potential of using IF-nanoparticles for enhancing the thermomechanical properties of thermoplastic polymers compared to other nanoscale fillers.

Dynamics of thermal ignition of spray flames in mixing layers

Conditions are identified under which analyses of laminar mixing layers can shed light on aspects of turbulent spray combustion. With this in mind, laminar spray-combustion models are formulated for both non-premixed and partially premixed systems. The laminar mixing layer separating a hot-air stream from a monodisperse spray carried by either an inert gas or air is investigated numerically and analytically in an effort to increase understanding of the ignition process leading to stabilization of high-speed spray combustion. The problem is formulated in an Eulerian framework, with the conservation equations written in the boundary-layer approximation and with a one-step Arrhenius model adopted for the chemistry description. The numerical integrations unveil two different types of ignition behaviour depending on the fuel availability in the reaction kernel, which in turn depends on the rates of droplet vaporization and fuel-vapour diffusion. When sufficient fuel is available near the hot boundary, as occurs when the thermochemical properties of heptane are employed for the fuel in the integrations, combustion is established through a precipitous temperature increase at a well-defined thermal-runaway location, a phenomenon that is amenable to a theoretical analysis based on activation-energy asymptotics, presented here, following earlier ideas developed in describing unsteady gaseous ignition in mixing layers. By way of contrast, when the amount of fuel vapour reaching the hot boundary is small, as is observed in the computations employing the thermochemical properties of methanol, the incipient chemical reaction gives rise to a slowly developing lean deflagration that consumes the available fuel as it propagates across the mixing layer towards the spray. The flame structure that develops downstream from the ignition point depends on the fuel considered and also on the spray carrier gas, with fuel sprays carried by air displaying either a lean deflagration bounding a region of distributed reaction or a distinct double-flame structure with a rich premixed flame on the spray side and a diffusion flame on the air side. Results are calculated for the distributions of mixture fraction and scalar dissipation rate across the mixing layer that reveal complexities that serve to identify differences between spray-flamelet and gaseous-flamelet problems.