20 resultados para Identification (control systems)
em Universidad Politécnica de Madrid
Resumo:
The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. In the last years, the required quick response of the ventilation system, from normal to emergency mode, has been improved by the use of automatic and semi-automatic control systems, what reduces the response times through the support to the operators decision taking, and the use of pre-defined strategies. A further step consists on the use of closedloop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc), optimizing the quality of the smoke control process
Resumo:
This article presents a cooperative manoeuvre among three dual mode cars – vehicles equipped with sensors and actuators, and that can be driven either manually or autonomously. One vehicle is driven autonomously and the other two are driven manually. The main objective is to test two decision algorithms for priority conflict resolution at intersections so that a vehicle autonomously driven can take their own decision about crossing an intersection mingling with manually driven cars without the need for infrastructure modifications. To do this, the system needs the position, speeds, and turning intentions of the rest of the cars involved in the manoeuvre. This information is acquired via communications, but other methods are also viable, such as artificial vision. The idea of the experiments was to adjust the speed of the manually driven vehicles to force a situation where all three vehicles arrive at an intersection at the same time.
Resumo:
Evaluation of three solar and daylighting control systems based on Calumen II, Ecotect and Radiance simulation programs to obtain an energy efficient and healthy interior in the experimental building prototype SDE10
Resumo:
The solutions to cope with new challenges that societies have to face nowadays involve providing smarter daily systems. To achieve this, technology has to evolve and leverage physical systems automatic interactions, with less human intervention. Technological paradigms like Internet of Things (IoT) and Cyber-Physical Systems (CPS) are providing reference models, architectures, approaches and tools that are to support cross-domain solutions. Thus, CPS based solutions will be applied in different application domains like e-Health, Smart Grid, Smart Transportation and so on, to assure the expected response from a complex system that relies on the smooth interaction and cooperation of diverse networked physical systems. The Wireless Sensors Networks (WSN) are a well-known wireless technology that are part of large CPS. The WSN aims at monitoring a physical system, object, (e.g., the environmental condition of a cargo container), and relaying data to the targeted processing element. The WSN communication reliability, as well as a restrained energy consumption, are expected features in a WSN. This paper shows the results obtained in a real WSN deployment, based on SunSPOT nodes, which carries out a fuzzy based control strategy to improve energy consumption while keeping communication reliability and computational resources usage among boundaries.
Resumo:
Communications Based Train Control Systems require high quality radio data communications for train signaling and control. Actually most of these systems use 2.4GHz band with proprietary radio transceivers and leaky feeder as distribution system. All them demand a high QoS radio network to improve the efficiency of railway networks. We present narrow band, broad band and data correlated measurements taken in Madrid underground with a transmission system at 2.4 GHz in a test network of 2 km length in subway tunnels. The architecture proposed has a strong overlap in between cells to improve reliability and QoS. The radio planning of the network is carefully described and modeled with narrow band and broadband measurements and statistics. The result is a network with 99.7% of packets transmitted correctly and average propagation delay of 20ms. These results fulfill the specifications QoS of CBTC systems.
Resumo:
This paper shows the actual state of a compilation work on Thermal Control Design Data being done at Madrid (Lamf-ETSIA) under several ESTEC contracts, introducing a Handbook already issued, its additions and updatings.
Resumo:
La mosca mediterránea de la fruta Ceratitis capitata (Wiedemann, 1824) está considerada una de las plagas clave para la fruticultura. El malatión es un insecticida organofosforado que fue empleado mayoritariamente en España para el control de C. capitata hasta 2009, año en el que dejó de utilizarse por no estar incluido en el anexo I de la Directiva Europea 91/414/ECC. El incremento del uso del malatión, debido a las graves pérdidas económicas causadas por C. capitata, provocó la aparición de poblaciones de campo resistentes. El estudio de una población resistente a malatión, recogida en Castelló en 2004, permitió la identificación de dos mecanismos de resistencia: una mutación puntual (G328A) en la acetilcolinesterasa (AChE) y un mecanismo de resistencia metabólica, probablemente mediado por carboxilesterasas. Teniendo en cuenta estos antecedentes, nos propusimos estudiar los mecanismos implicados en la resistencia a malatión en C. capitata. Además, durante el desarrollo de esta Tesis, el malatión fue sustituido por otros insecticidas como el espinosad y la lambda-cialotrina para el control de la plaga. En este nuevo contexto, es extremadamente importante analizar la susceptibilidad de poblaciones de campo frente a espinosad y estudiar la posible existencia de resistencia cruzada a estos insecticidas, así como sentar las bases para el estudio de futuros mecanismos de resistencia. En primer lugar, analizamos mediante bioensayos con dosis discriminante la susceptibilidad a malatión y espinosad en doce poblaciones de C. capitata de Andalucía, Aragón, Cataluña, Comunidad Valenciana e Islas Baleares; y nuestros resultados sugirieron la presencia de individuos resistentes a malatión en la mayoría de las poblaciones analizadas. En el caso del espinosad, observamos que la susceptibilidad a este insecticida de origen biológico fue elevada en la mayoría de las poblaciones, sin embargo, la población recogida en Xàbia (Alicante) mostró un nivel de susceptibilidad unas dos veces menor al resto de poblaciones. Mediante la selección en laboratorio, obtuvimos dos líneas resistentes a malatión, W-4Km y W-10Km, con unos niveles de resistencia con respeto a la línea susceptible C de 178 y 400 veces, respectivamente. Además, se seleccionó por primera vez en C. capitata una línea altamente resistente a espinosad (Xàbia-W-100s), que actualmente es unas 500 veces más resistente que la línea de laboratorio C. Con el objetivo de escoger la estrategia más adecuada para el manejo de la plaga, estudiamos la susceptibilidad a diferentes tipos de insecticidas en la línea resistente a malatión W- 4Km. En esta línea detectamos resistencia cruzada moderada a los organofosforados fentión, diazinón, fosmet, triclorfón y metil-clorpirifos (de 7 a 16 veces) y frente al carbamato carbaril, al piretroide lambda-cialotrina y al quimioesterilizante lufenurón (de 4 a 6 veces). Por otra parte, la resistencia cruzada frente a espinosad fue baja (1,5 veces). Es importante destacar que los niveles de resistencia estimados frente a todos los insecticidas fueron de uno o dos órdenes de magnitud inferiores al observado en la línea W-4Km frente a malatión (178 veces), hecho que podría deberse, al menos, a dos posibles hipótesis: que la mutación AChE G328A confiera mayor insensibilidad al malaoxón (forma activa del malatión) que a otros insecticidas que tienen como diana la AChE y/o, en segundo lugar, que el mecanismo de resistencia mediado por carboxilesterasas hidrolice el malatión de manera más eficiente que los otros insecticidas analizados. En el estudio de nuevos mecanismos de resistencia en C. capitata, por un lado, analizamos la diversidad de enzimas citocromo P450, asociadas con resistencia metabólica en otras especies, y por otro lado, desarrollamos un sistema para la detección de nuevas mutaciones puntuales que pudiesen aparecer en los genes que codifican la AChE (Ccace2) y la aliesterasa (Ccae7). Mediante el empleo de cebadores degenerados obtuvimos 37 genes CYP, que codifican enzimas P450, pertenecientes a cinco familias. Posteriormente, en un estudio de inducción con fenobarbital, observamos que la expresión de cuatro de los seis genes analizados era susceptible de ser inducida. Por otro lado, se puso a punto un sistema que permite amplificar y secuenciar, a partir de DNA genómico, los exones de los genes Ccace2 y Ccae7 en los que se han encontrado mutaciones relacionadas con resistencia a insecticidas en otras especies. Los resultados obtenidos facilitarán el estudio de nuevos mecanismos de resistencia mediados por estas enzimas en C. capitata. Se diseñó un método PCR-RFLP para identificar los individuos portadores de la mutación AChE G328A (alelo de resistencia Ccace2R) sin la necesidad de realizar bioensayos y que, además, permite detectar resistencia cuando ésta se encuentra a baja frecuencia. Según el análisis realizado, el alelo Ccace2R se observó en 25 de las 27 localidades españolas muestreadas en el territorio español, incluyendo las Islas Baleares y Canarias. Sin embargo, este alelo no se detectó en poblaciones procedentes de once países y de cinco continentes. El análisis de la presencia del alelo Ccace2R en las líneas resistentes a malatión durante el proceso de selección en el laboratorio mostró una rápida disminución de los homocigotos, tanto para el alelo susceptible como para el alelo de resistencia, en favor de los individuos heterocigotos. Así, después de 52 generaciones de selección, se observó que la totalidad de los individuos analizados de la línea W-10Km presentaban un genotipo heterocigoto para la mutación AChE G328A. Este desequilibrio contradice la segregación mendeliana esperada para un gen con dos alelos pero podría ser explicado por la existencia de una duplicación del gen Ccace2. La demostración de la presencia de esta duplicación se realizó mediante: i) el cruzamiento de individuos heterocigotos de la línea W-10Km con homocigotos susceptibles de la línea C, que dio lugar a una descendencia en la que el 100% de los individuos eran heterocigotos; ii) la evaluación del número de copias del gen Ccace2 por PCR cuantitativa en tiempo real (qPCR), que resultó dos veces mayor en individuos de la línea W-10Km en comparación con los de la línea C; iii) el análisis del nivel de expresión de Ccace2, que fue el doble en la línea W-10Km con respecto a la línea C, y iv) el estudio de la actividad AChE, que resultó mayor en los individuos de la línea W-10Km. Según los resultados obtenidos, una duplicación del gen Ccace2 provoca la coexistencia en un mismo cromosoma del alelo silvestre y del alelo mutado y, además, las dos copias del gen Ccace2, al estar ligadas, producen una heterocigosis permanente (Ccace2RS). De esta manera se explica que el hecho de que 100% de los individuos de la línea W-10Km mostrasen un perfil de restricción correspondiente a un individuo heterocigoto ya que, en realidad, eran homocigotos estructurales para la duplicación (genotipo CCace2RS/RS). Se ha detectado un coste biológico asociado a la duplicación que consiste en un incremento en la mortalidad acumulada de los adultos a partir del séptimo día después de la emergencia. La descripción de la duplicación Ccace2RS supone la identificación de un nuevo mecanismo de resistencia a malatión en C. capitata. Finalmente, mediante el diseño de un método de doble PCR-RFLP se determinó la presencia de la duplicación Ccace2RS en la mayoría de las poblaciones españolas. La proporción de individuos portadores de la duplicación osciló entre el 5% y el 35%, observándose los mayores valores de frecuencia en las poblaciones de C. capitata recogidas en la cuenca mediterránea. Podemos por lo tanto concluir que la resistencia a malatión asociada a la mutación AChE G328A y a la duplicación Ccace2RS está ampliamente establecida en las poblaciones españolas de C. capitata. Nuestros resultados desaconsejan la utilización del malatión (si fuera de nuevo autorizado) o de otros organofosforados para el control de esta plaga. Además, una de las líneas resistentes a malatión mostró resistencia cruzada frente a insecticidas con diferentes modos de acción y que se utilizan actualmente para el control de C. capitata, tales como lambda-cialotrina y lufenurón. La alta susceptibilidad a espinosad observada en las poblaciones españolas, así como la reducida resistencia cruzada estimada para este insecticida, sugieren que su utilización es adecuada para el control de la plaga. Sin embargo, la utilización de un sólo insecticida puede entrañar riesgos por favorecer la selección de resistencia, de hecho, mediante selección en laboratorio se obtuvo una población altamente resistente a espinosad. Por tanto, es recomendable implementar programas de control integrado y de manejo de la resistencia en C. capitata utilizando distintos sistemas de control e insecticidas con diferentes mecanismos de acción que permitan su sostenibilidad en el tiempo. Los sistemas de detección de alelos de resistencia desarrollados en este trabajo permitirán la detección precoz de resistencia en campo, facilitando la decisión sobre el sistema de control más adecuado. Además, los conocimientos generados podrán contribuir al desarrollo de nuevos sistemas de detección para otros mecanismos de resistencia. Abstract. The Mediterranean fruit fly, Ceratitis capitata (Wiedemann, 1824), is considered one of the most harmful pests in fruit crops. Until 2009, when malathion use was banned due to its not inclusion in the Annex I of Directive 91/414/EEC, the application of this organophosphate (OP) insecticide in Spain increased gradually due to the large economic losses caused by C. capitata. The increase in the frequency of treatments resulted in the development of resistant field populations. The study of a malathion-resistant population, collected in 2004 in Castelló (Comunidad Valenciana), allowed the identification of two resistance mechanisms: a single point mutation (G328A) in the target acetylcholinesterase (AChE), as well as a metabolic resistance mechanism, most likely carboxylesterase-mediated. Taking all the preceding into account, we studied the malathion resistance mechanisms in C. capitata. During the development of this PhD Thesis malathion use was banned by the European Union, being replaced by other insecticides, such as spinosad and lambda-cyhalotrin. Within this new working frame, the need to analyse the possible existence of cross-resistance to these insecticides and the susceptibility to spinosad in field populations was raised. This would define the baseline for future studies on resistance mechanisms. Firstly, through discriminant dose bioassays, we analysed malathion and spinosad susceptibility in twelve C. capitata populations from Andalucia, Aragon, Cataluña, C. Valenciana and the Baleares Islands. Our results suggest the presence of malathion-resistant individuals in most of the populations analysed. Regarding spinosad, we noticed a high susceptibility to this biologically derived insecticide in most of the populations, but in the one collected in Xabia (Alicante), which had a susceptibility level two times lower than the rest of populations. Through laboratory selection, we obtained two malathion-resistant strains, W-4Km and W-10Km, with resistance levels 178- and 400-fold, respectively, compared to the control susceptible C strain. Besides, a strain highly-resistant to spinosad (Xabia-W-100s), 500-times more resistant than control C strain, was selected. In order to decide the most appropriate management strategy for the pest, we studied the susceptibility to different insecticides in the malathion-resistant W-4Km strain. We detected a moderated cross-resistance to the OPs fenthion, diazinon, phosmet, trichlorphon and methylchlorpyrifos (7- to 16-fold), and to the carbamate carbaryl, the pyretroid lambda-cyhalotrin and the chemosterilizer lufenuron (4- to 6-fold). On the other hand, cross-resistance to spinosad was low (1.5-fold). It is important to note that resistance levels to all insecticides were one or two orders of magnitude less than that observed against malathion in W-4Km strain (178-fold), a fact that might be due to, at least, two possible causes: mutation AChE G328A may provide a higher insensitivity to malaoxon (the active form of malathion) than to other insecticides having AChE as target, and/or, secondly, the carboxylesterase-mediated resistance mechanism hydrolyzes malathion more efficiently than all other analysed insecticides. To investigate new resistance mechanisms in C. capitata we analysed the diversity of the cytochrome P450 enzymes, which have been associated to metabolic resistance in insects, and we developed a new method to detect single point mutations in acetylcholinesterase (Ccace2) and aliesterase (Ccae7) genes that could appear. Using degenerate primers we obtained 37 CYP genes, coding P450 enzymes, included in five families. Afterwards, in a phenobarbital-induction study, we observed that the expression of 4 out of the 6 analysed genes could be induced. On the other hand, a system was set up to amplify and to sequence from genomic DNA the exons of genes Ccace2 and Ccae7 where mutations related to insecticide resistance have been found in other species. The results obtained could facilitate the study of new resistance mechanisms in C. capitata mediated by these enzymes. A PCR-RFLP method was designed to detect the presence of the mutation AChE G328A (resistance allele Ccace2R), with no need to perform bioassays and allowing detecting resistance at low frequency. According to the analysis, the resistance allele was found in 25 out of 27 sampled locations in Spain, including the Balearic and the Canary Islands. However, this allele was not detected in other populations collected in 11 countries from 5 continents. The follow-up of the presence of the allele Ccace2R in the malathion-resistant strains during the selection process in the laboratory showed a quick decrease in homozygous individuals, for both the susceptible and the resistant alleles, favouring heterozygous. Thus, after 52 generations of selection, all the individuals analysed from W-10Km strain showed a heterozygous genotype for mutation AChE G328A, contradicting mendelian segregation as expected for a gene with two alleles. Afterwards, we were able to demonstrate that this was caused by the presence of a duplication of the gene coding acetylcholinesterase by: i) crossing heterozygous individuals from W-10Km strain with susceptible homozygous from C strain, originating a F1 population in which 100% of individuals were heterozygous; ii) evaluating the number of copies of gen Ccace2 by quantitative PCR in real time (qPCR), that happened to be twice higher in individuals from W-10Km VII strain when compared with C strain; iii) analysing the level of expression of Ccace2, twice in W- 10Km strain when compared to C strain; iv) studying the acetylcholinesterase activity, that was higher in individuals from W-10Km strain. According to these results, duplication of gen Ccace2 originates the coexistence of the susceptible and the resistant allele in the same chromosome. The two linked copies of the gene Ccace2 provoke the existence of permanent heterozygosis (Ccace2RS). This explains why the 100% of individuals from W-10Km strain showed an heterozygous restriction pattern since, in fact, they were structural homozygotes for the duplication (genotype Ccace2RS/RS). A biological cost has been detected associated to this duplication, consisting in a rise in accumulated adult mortality from the seventh day after emergence. The Ccace2RS duplication described in this study represents a new resistance mechanism to malathion in C. capitata. Finally, by the design of a double PCR-RFLP method, the presence of Ccace2RS duplication was confirmed in most of the Spanish populations. We observed that the proportion of individuals carrying the duplication oscillated between 5 and 35%, the frequency being higher in those C. capitata populations collected in the area of the Mediterranean basin. Therefore, we can conclude that malathion resistance associated to mutation AChE G328A and to Ccace2RS duplication are widely distributed in Spanish populations of C. capitata. Our results advice against the use of malathion (if it came to be newly authorized for use) or other OPs for the control of this pest. Besides, one of the malathion-resistant strains showed cross-resistance against insecticides with diverse action modes that are currently used for pest control, such as lambdacyhalotrin and lufenuron. High susceptibility to spinosad in the Spanish populations, as well as the reduced cross-resistance estimated for this insecticide suggests its adequacy for Medfly control. However, the use of a single insecticide is a risky strategy since it favours the selection of resistance. In fact, a population highly resistant to spinosad was obtained through laboratory selection. Therefore, it is advisable to implement integrated pest management (IPM) and resistance management programs for C. capitata control. Using insecticides with different modes of action and diverse control systems would contribute to the sustainability of the pest control. The resistance allele detection systems developed through this work will allow the early detection of resistance in the field, making possible the selection of the most appropriate method for pest control. Besides, the generated knowledge may also contribute to the development of new detection systems for other resistance mechanisms.
Resumo:
A set of software development tools for building real-time control systems on a simple robotics platform is described in the paper. The tools are being used in a real-time systems course as a basis for student projects. The development platform is a low-cost PC running GNU/Linux, and the target system is LEGO MINDSTORMS NXT, thus keeping the cost of the laboratory low. Real-time control software is developed using a mixed paradigm. Functional code for control algorithms is automatically generated in C from Simulink models. This code is then integrated into a concurrent, real-time software architecture based on a set of components written in Ada. This approach enables the students to take advantage of the high-level, model-oriented features that Simulink oers for designing control algorithms, and the comprehensive support for concurrency and real-time constructs provided by Ada.
Resumo:
This paper describes a novel deployment of an intelligent user-centered HVAC (Heating, Ventilating and Air Conditioner) control system. The main objective of this system is to optimize user comfort and to reduce energy consumption in office buildings. Existing commercial HVAC control systems work in a fixed and predetermined way. The novelty of the proposed system is that it adapts dynamically to the user and to the building environment. For this purpose the system architecture has been designed under the paradigm of Ambient Intelligence. A prototype of the system proposed has been tested in a real-world environment.
Resumo:
The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. The required immediate transition, from normal to emergency functioning of the ventilation equipments, is being strengthened by the use of automatic and semi-automatic control systems, what reduces the response times through the help to the operators, and the use of pre-defined strategies. A further step consists on the use of closed-loop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc.), optimizing smoke control capacity.
Resumo:
In the last years, there has been a continued growth in the number of offshore operations for handling large equipment and objects, with emphasis on installation and maintenance of devices for exploiting marine renewable energy like generators for harnessing wind, waves and currents energy. Considering the behaviour of these devices during manoeuvrings, and due to their size and by the interaction with the surrounding fluid, the effect of inertial forces and torques is very important, which requires a specific modelling. This paper especially discusses the masses and moments of inertia modelling problem, with the aim to use it in the simulation of the complex manoeuvres of these devices and in the automatic control systems designed for their offshore operations. Given the importance and complexity of the added mass modelling, a method for its early design identification, developed by the R&D Group on Marine Renewable Energy Technologies of the UPM (GITERM) and its use on special cases like emersion manoeuvres of devices from underwater to the surface will be presented.
Resumo:
This paper describes a general approach for real time traffic management support using knowledge based models. Recognizing that human intervention is usually required to apply the current automatic traffic control systems, it is argued that there is a need for an additional intelligent layer to help operators to understand traffic problems and to make the best choice of strategic control actions that modify the assumption framework of the existing systems.
Resumo:
Los sistemas de tiempo real tienen un papel cada vez más importante en nuestra sociedad. Constituyen un componente fundamental de los sistemas de control, que a su vez forman parte de diversos sistemas de ingeniería básicos en actividades industriales, militares, de comunicaciones, espaciales y médicas. La planificación de recursos es un problema fundamental en la realización de sistemas de tiempo real. Su objetivo es asignar los recursos disponibles a las tareas de forma que éstas cumplan sus restricciones temporales. Durante bastante tiempo, el estado de la técnica en relación con los métodos de planificación ha sido rudimentario. En la actualidad, los métodos de planificación basados en prioridades han alcanzado un nivel de madurez suficiente para su aplicación en entornos industriales. Sin embargo, hay cuestiones abiertas que pueden dificultar su utilización. El objetivo principal de esta tesis es estudiar los métodos de planificación basados en prioridades, detectar las cuestiones abiertas y desarrollar protocolos, directrices y esquemas de realización práctica que faciliten su empleo en sistemas industriales. Una cuestión abierta es la carencia de esquemas de realización de algunos protocolos con núcleos normalizados. El resultado ha sido el desarrollo de esquemas de realización de tareas periódicas y esporádicas de tiempo real, con detección de fallos de temporización, comunicación entre tareas, cambio de modo de ejecución del sistema y tratamiento de fallos mediante grupos de recuperación. Los esquemas se han codificado en Ada 9X y se proporcionan directrices para analizar la planificabilidad de un sistema desarrollado con esta base. Un resultado adicional ha sido la identificación de la funcionalidad mínima necesaria para desarrollar sistemas de tiempo real con las características enumeradas. La capacidad de adaptación a los cambios del entorno es una característica deseable de los sistemas de tiempo real. Si estos cambios no estaban previstos en la fase de diseño o si hay módulos erróneos, es necesario modificar o incluir algunas tareas. La actualización del sistema se suele realizar estáticamente y su instalación se lleva a cabo después de parar su ejecución. Sin embargo, hay sistemas cuyo funcionamiento no se puede detener sin producir daños materiales o económicos. Una alternativa es diseñar el sistema como un conjunto de unidades que se pueden reemplazar, sin interferir con la ejecución de otras unidades. Para tal fin, se ha desarrollado un protocolo de reemplazamiento dinámico para sistemas de tiempo real crítico y se ha comprobado su compatibilidad con los métodos de planificación basados en prioridades. Finalmente se ha desarrollado un esquema de realización práctica del protocolo.---ABSTRACT---Real-time systems are very important now a days. They have become a relevant issue in the design of control systems, which are a basic component of several engineering systems in industrial, telecommunications, military, spatial and medical applications. Resource scheduling is a central issue in the development of real-time systems. Its purpose is to assign the available resources to the tasks, in such a way that their deadlines are met. Historically, hand-crafted techniques were used to develop real-time systems. Recently, the priority-based scheduling methods have reached a sufficient maturity level to be feasible its extensive use in industrial applications. However, there are some open questions that may decrease its potential usefulness. The main goal of this thesis is to study the priority-based scheduling methods, to identify the remaining open questions and to develop protocols, implementation templates and guidelines that will make more feasible its use in industrial applications. One open question is the lack of implementation schemes, based on commercial realtime kernels, of some of the protocols. POSIX and Ada 9X has served to identify the services usually available. A set of implementation templates for periodic and sporadic tasks have been developed with provisión for timing failure detection, intertask coraraunication, change of the execution mode and failure handling based on recovery groups. Those templates have been coded in Ada 9X. A set of guidelines for checking the schedulability of a system based on them are also provided. An additional result of this work is the identification of the minimal functionality required to develop real-time systems based on priority scheduling methods, with the above characteristics. A desirable feature of real-time systems is their capacity to adapt to changes in the environment, that cannot be entirely predicted during the design, or to misbehaving software modules. The traditional maintenance techniques are performed by stopping the whole system, installing the new application and finally resuming the system execution. However this approach cannot be applied to non-stop systems. An alternative is to design the system as a set of software units that can be dynamically replaced within its operative environment. With this goal in mind, a dynamic replacement protocol for hard real-time systems has been defined. Its compatibility with priority-based scheduling methods has been proved. Finally, a execution témplate of the protocol has been implemented.
Resumo:
In current industrial environments there is an increasing need for practical and inexpensive quality control systems to detect the foreign food materials in powder food processing lines. This demand is especially important for the detection of product adulteration with traces of highly allergenic products, such as peanuts and tree nuts. Manufacturing industries dealing with the processing of multiple powder food products present a substantial risk for the contamination of powder foods with traces of tree nuts and other adulterants, which might result in unintentional ingestion of nuts by the sensitised population. Hence, the need for an in-line system to detect nut traces at the early stages of food manufacturing is of crucial importance. In this present work, a feasibility study of a spectral index for revealing adulteration of tree nut and peanut traces in wheat flour samples with hyperspectral images is reported. The main nuts responsible for allergenic reactions considered in this work were peanut, hazelnut and walnut. Enhanced contrast between nuts and wheat flour was obtained after the application of the index. Furthermore, the segmentation of these images by selecting different thresholds for different nut and flour mixtures allowed the identification of nut traces in the samples. Pixels identified as nuts were counted and compared with the actual percentage of peanut adulteration. As a result, the multispectral system was able to detect and provide good visualisation of tree nut and peanut trace levels down to 0.01% by weight. In this context, multispectral imaging could operate in conjuction with chemical procedures, such as Real Time Polymerase Chain Reaction and Enzyme-Linked Immunosorbent Assay to save time, money and skilled labour on product quality control. This approach could enable not only a few selected samples to be assessed but also to extensively incorporate quality control surveyance on product processing lines.
Resumo:
In current industrial environments there is an increasing need for practical and inexpensive quality control systems to detect the foreign food materials in powder food processing lines. This demand is especially important for the detection of product adulteration with traces of highly allergenic products, such as peanuts and tree nuts. Manufacturing industries dealing with the processing of multiple powder food products present a substantial risk for the contamination of powder foods with traces of tree nuts and other adulterants, which might result in unintentional ingestion of nuts by the sensitised population. Hence, the need for an in-line system to detect nut traces at the early stages of food manufacturing is of crucial importance. In this present work, a feasibility study of a spectral index for revealing adulteration of tree nut and peanut traces in wheat flour samples with hyperspectral images is reported. The main nuts responsible for allergenic reactions considered in this work were peanut, hazelnut and walnut. Enhanced contrast between nuts and wheat flour was obtained after the application of the index. Furthermore, the segmentation of these images by selecting different thresholds for different nut and flour mixtures allowed the identification of nut traces in the samples. Pixels identified as nuts were counted and with the actual percentage of peanut adulteration. As a result, the multispectral system was able to detect and provide good visualisation of tree nut and peanut trace levels down to 0.01% by weight. In this context, multispectral imaging could operate in conjuction with chemical procedures, such as Real Time Polymerase Chain Reaction and Enzyme-Linked Immunosorbent Assay to save time, money and skilled labour on product quality control. This approach could enable not only a few selected samples to be assessed but also to extensively incorporate quality control surveyance on product processing lines.