Analysis of the static and dynamic behaviour of hydraulic fills

En la actualidad existe un gran conocimiento en la caracterización de rellenos hidráulicos, tanto en su caracterización estática, como dinámica. Sin embargo, son escasos en la literatura estudios más generales y globales de estos materiales, muy relacionados con sus usos y principales problemáticas en obras portuarias y mineras. Los procedimientos semi‐empíricos para la evaluación del efecto silo en las celdas de cajones portuarios, así como para el potencial de licuefacción de estos suelos durantes cargas instantáneas y terremotos, se basan en estudios donde la influencia de los parámetros que los rigen no se conocen en gran medida, dando lugar a resultados con considerable dispersión. Este es el caso, por ejemplo, de los daños notificados por el grupo de investigación del Puerto de Barcelona, la rotura de los cajones portuarios en el Puerto de Barcelona en 2007. Por estos motivos y otros, se ha decidido desarrollar un análisis para la evaluación de estos problemas mediante la propuesta de una metodología teórico‐numérica y empírica. El enfoque teórico‐numérico desarrollado en el presente estudio se centra en la determinación del marco teórico y las herramientas numéricas capaces de solventar los retos que presentan estos problemas. La complejidad del problema procede de varios aspectos fundamentales: el comportamiento no lineal de los suelos poco confinados o flojos en procesos de consolidación por preso propio; su alto potencial de licuefacción; la caracterización hidromecánica de los contactos entre estructuras y suelo (camino preferencial para el flujo de agua y consolidación lateral); el punto de partida de los problemas con un estado de tensiones efectivas prácticamente nulo. En cuanto al enfoque experimental, se ha propuesto una metodología de laboratorio muy sencilla para la caracterización hidromecánica del suelo y las interfaces, sin la necesidad de usar complejos aparatos de laboratorio o procedimientos excesivamente complicados. Este trabajo incluye por tanto un breve repaso a los aspectos relacionados con la ejecución de los rellenos hidráulicos, sus usos principales y los fenómenos relacionados, con el fin de establecer un punto de partida para el presente estudio. Este repaso abarca desde la evolución de las ecuaciones de consolidación tradicionales (Terzaghi, 1943), (Gibson, English & Hussey, 1967) y las metodologías de cálculo (Townsend & McVay, 1990) (Fredlund, Donaldson and Gitirana, 2009) hasta las contribuciones en relación al efecto silo (Ranssen, 1985) (Ravenet, 1977) y sobre el fenómeno de la licuefacción (Casagrande, 1936) (Castro, 1969) (Been & Jefferies, 1985) (Pastor & Zienkiewicz, 1986). Con motivo de este estudio se ha desarrollado exclusivamente un código basado en el método de los elementos finitos (MEF) empleando el programa MATLAB. Para ello, se ha esablecido un marco teórico (Biot, 1941) (Zienkiewicz & Shiomi, 1984) (Segura & Caron, 2004) y numérico (Zienkiewicz & Taylor, 1989) (Huerta & Rodríguez, 1992) (Segura & Carol, 2008) para resolver problemas de consolidación multidimensional con condiciones de contorno friccionales, y los correspondientes modelos constitutivos (Pastor & Zienkiewicz, 1986) (Fiu & Liu, 2011). Asimismo, se ha desarrollado una metodología experimental a través de una serie de ensayos de laboratorio para la calibración de los modelos constitutivos y de la caracterización de parámetros índice y de flujo (Castro, 1969) (Bahda 1997) (Been & Jefferies, 2006). Para ello se han empleado arenas de Hostun como material (relleno hidráulico) de referencia. Como principal aportación se incluyen una serie de nuevos ensayos de corte directo para la caracterización hidromecánica de la interfaz suelo – estructura de hormigón, para diferentes tipos de encofrados y rugosidades. Finalmente, se han diseñado una serie de algoritmos específicos para la resolución del set de ecuaciones diferenciales de gobierno que definen este problema. Estos algoritmos son de gran importancia en este problema para tratar el procesamiento transitorio de la consolidación de los rellenos hidráulicos, y de otros efectos relacionados con su implementación en celdas de cajones, como el efecto silo y la licuefacciones autoinducida. Para ello, se ha establecido un modelo 2D axisimétrico, con formulación acoplada u‐p para elementos continuos y elementos interfaz (de espesor cero), que tratan de simular las condiciones de estos rellenos hidráulicos cuando se colocan en las celdas portuarias. Este caso de estudio hace referencia clara a materiales granulares en estado inicial muy suelto y con escasas tensiones efectivas, es decir, con prácticamente todas las sobrepresiones ocasionadas por el proceso de autoconsolidación (por peso propio). Por todo ello se requiere de algoritmos numéricos específicos, así como de modelos constitutivos particulares, para los elementos del continuo y para los elementos interfaz. En el caso de la simulación de diferentes procedimientos de puesta en obra de los rellenos se ha requerido la modificacion de los algoritmos empleados para poder así representar numéricamente la puesta en obra de estos materiales, además de poder realizar una comparativa de los resultados para los distintos procedimientos. La constante actualización de los parámetros del suelo, hace también de este algoritmo una potente herramienta que permite establecer un interesante juego de perfiles de variables, tales como la densidad, el índice de huecos, la fracción de sólidos, el exceso de presiones, y tensiones y deformaciones. En definitiva, el modelo otorga un mejor entendimiento del efecto silo, término comúnmente usado para definir el fenómeno transitorio del gradiente de presiones laterales en las estructuras de contención en forma de silo. Finalmente se incluyen una serie de comparativas entre los resultados del modelo y de diferentes estudios de la literatura técnica, tanto para el fenómeno de las consolidaciones por preso propio (Fredlund, Donaldson & Gitirana, 2009) como para el estudio del efecto silo (Puertos del Estado, 2006, EuroCódigo (2006), Japan Tech, Stands. (2009), etc.). Para concluir, se propone el diseño de un prototipo de columna de decantación con paredes friccionales, como principal propuesta de futura línea de investigación. Wide research is nowadays available on the characterization of hydraulic fills in terms of either static or dynamic behavior. However, reported comprehensive analyses of these soils when meant for port or mining works are scarce. Moreover, the semi‐empirical procedures for assessing the silo effect on cells in floating caissons, and the liquefaction potential of these soils during sudden loads or earthquakes are based on studies where the underlying influence parameters are not well known, yielding results with significant scatter. This is the case, for instance, of hazards reported by the Barcelona Liquefaction working group, with the failure of harbor walls in 2007. By virtue of this, a complex approach has been undertaken to evaluate the problem by a proposal of numerical and laboratory methodology. Within a theoretical and numerical scope, the study is focused on the numerical tools capable to face the different challenges of this problem. The complexity is manifold; the highly non‐linear behavior of consolidating soft soils; their potentially liquefactable nature, the significance of the hydromechanics of the soil‐structure contact, the discontinuities as preferential paths for water flow, setting “negligible” effective stresses as initial conditions. Within an experimental scope, a straightforward laboratory methodology is introduced for the hydromechanical characterization of the soil and the interface without the need of complex laboratory devices or cumbersome procedures. Therefore, this study includes a brief overview of the hydraulic filling execution, main uses (land reclamation, filled cells, tailing dams, etc.) and the underlying phenomena (self‐weight consolidation, silo effect, liquefaction, etc.). It comprises from the evolution of the traditional consolidation equations (Terzaghi, 1943), (Gibson, English, & Hussey, 1967) and solving methodologies (Townsend & McVay, 1990) (Fredlund, Donaldson and Gitirana, 2009) to the contributions in terms of silo effect (Ranssen, 1895) (Ravenet, 1977) and liquefaction phenomena (Casagrande, 1936) (Castro, 1969) (Been & Jefferies, 1985) (Pastor & Zienkiewicz, 1986). The novelty of the study lies on the development of a Finite Element Method (FEM) code, exclusively formulated for this problem. Subsequently, a theoretical (Biot, 1941) (Zienkiewicz and Shiomi, 1984) (Segura and Carol, 2004) and numerical approach (Zienkiewicz and Taylor, 1989) (Huerta, A. & Rodriguez, A., 1992) (Segura, J.M. & Carol, I., 2008) is introduced for multidimensional consolidation problems with frictional contacts and the corresponding constitutive models (Pastor & Zienkiewicz, 1986) (Fu & Liu, 2011). An experimental methodology is presented for the laboratory test and material characterization (Castro 1969) (Bahda 1997) (Been & Jefferies 2006) using Hostun sands as reference hydraulic fill. A series of singular interaction shear tests for the interface calibration is included. Finally, a specific model algorithm for the solution of the set of differential equations governing the problem is presented. The process of consolidation and settlements involves a comprehensive simulation of the transient process of decantation and the build‐up of the silo effect in cells and certain phenomena related to self‐compaction and liquefaction. For this, an implementation of a 2D axi‐syimmetric coupled model with continuum and interface elements, aimed at simulating conditions and self‐weight consolidation of hydraulic fills once placed into floating caisson cells or close to retaining structures. This basically concerns a loose granular soil with a negligible initial effective stress level at the onset of the process. The implementation requires a specific numerical algorithm as well as specific constitutive models for both the continuum and the interface elements. The simulation of implementation procedures for the fills has required the modification of the algorithm so that a numerical representation of these procedures is carried out. A comparison of the results for the different procedures is interesting for the global analysis. Furthermore, the continuous updating of the model provides an insightful logging of variable profiles such as density, void ratio and solid fraction profiles, total and excess pore pressure, stresses and strains. This will lead to a better understanding of complex phenomena such as the transient gradient in lateral pressures due to silo effect in saturated soils. Interesting model and literature comparisons for the self‐weight consolidation (Fredlund, Donaldson, & Gitirana, 2009) and the silo effect results (Puertos del Estado (2006), EuroCode (2006), Japan Tech, Stands. (2009)). This study closes with the design of a decantation column prototype with frictional walls as the main future line of research.

LHPP, the light-harvesting NADPH:protochlorophyllide (Pchlide) oxido¬reductase:Pchlide complex of etiolated plants, is developmentally expressed across the barley leaf gradient

NADPH:protochlorophyllide oxidoreductase is a key enzyme for the light-induced greening of etiolated angiosperm plants. In barley, two POR proteins exist termed PORA and PORB that have previously been proposed to structurally and functionally cooperate in terms of a higher molecular mass light-harvesting complex named LHPP, in the prolamellar body of etioplasts [Nature 397 (1999) 80]. In this study we examined the expression pattern of LHPP during seedling etiolation and de-etiolation under different experimental conditions. Our results show that LHPP is developmentally expressed across the barley leaf gradient. We further provide evidence that LHPP operates both in plants that etiolate completely before being exposed to white light and in plants that etiolate only partially and begin light-harvesting as soon as traces of light become available in the uppermost parts of the soil. As a result of light absorption, in either case LHPP converts Pchlide a to chlorophyllide (Chlide) a and in turn disintegrates. The released Chlide a, as well as Chlide b produced upon LHPP’s light-dependent dissociation, which leads to the activation of the PORA as a Pchlide b-reducing enzyme, then bind to homologs of water-soluble chlorophyll proteins of Brassicaceae. We propose that these proteins transfer Chlide a and Chlide b to the thylakoids, where their esterification with phytol and assembly into the photosynthetic membrane complexes ultimately takes place. Presumably due to the tight coupling of LHPP synthesis and degradation, as well as WSCP formation and photosynthetic membrane assembly, efficient photo-protection is conferred onto the plant.

Interactions between roughness and topography in hydraulic models

Analysis of river flow using hydraulic modelling and its implications in derived environ-mental applications are inextricably connected with the way in which the river boundary shape is represented. This relationship is scale-dependent upon the modelling resolution which in turn determines the importance of a subscale performance of the model and the way subscale (surface and flow) processes are parameterised. Commonly, the subscale behaviour of the model relies upon a roughness parameterisation whose meaning depends on the dimensionality of the hydraulic model and the resolution of the topographic represen¬tation scale. This latter is, in turn, dependent on the resolution of the computational mesh as well as on the detail of measured topographic data. Flow results are affected by this interactions between scale and subscale parameterisation according to the dimensionality approach. The aim of this dissertation is the evaluation of these interactions upon hy¬draulic modelling results. Current high resolution topographic source availability induce this research which is tackled using a suitable roughness approach according to each di¬mensionality with the purpose of the interaction assessment. A 1D HEC-RAS model, a 2D raster-based diffusion-wave model with a scale-dependent distributed roughness parame-terisation and a 3D finite volume scheme with a porosity algorithm approach to incorporate complex topography have been used. Different topographic sources are assessed using a 1D scheme. LiDAR data are used to isolate the mesh resolution from the topographic content of the DEM effects upon 2D and 3D flow results. A distributed roughness parameterisation, using a roughness height approach dependent upon both mesh resolution and topographic content is developed and evaluated for the 2D scheme. Grain-size data and fractal methods are used for the reconstruction of topography with microscale information, required for some applications but not easily available. Sensitivity of hydraulic parameters to this topographic parameterisation is evaluated in a 3D scheme at different mesh resolu¬tions. Finally, the structural variability of simulated flow is analysed and related to scale interactions. Model simulations demonstrate (i) the importance of the topographic source in a 1D models; (ii) the mesh resolution approach is dominant in 2D and 3D simulations whereas in a 1D model the topographic source and even the roughness parameterisation impacts are more critical; (iii) the increment of the sensitivity to roughness parameterisa-tion in 1D and 2D schemes with detailed topographic sources and finer mesh resolutions; and (iv) the topographic content and microtopography impact throughout the vertical profile of computed 3D velocity in a depth-dependent way, whereas 2D results are not affected by topographic content variations. Finally, the spatial analysis shows that the mesh resolution controls high resolution model scale results, roughness parameterisation control 2D simulation results for a constant mesh resolution; and topographic content and micro-topography variations impacts upon the organisation of flow results depth-dependently in a 3D scheme. Resumen La topografía juega un papel fundamental en la distribución del agua y la energía en los paisajes naturales (Beven and Kirkby 1979; Wood et al. 1997). La simulación hidráulica combinada con métodos de medición del terreno por teledetección constituyen una poderosa herramienta de investigación en la comprensión del comportamiento de los flujos de agua debido a la variabilidad de la superficie sobre la que fluye. La representación e incorporación de la topografía en el esquema hidráulico tiene una importancia crucial en los resultados y determinan el desarrollo de sus aplicaciones al campo medioambiental. Cualquier simulación es una simplificación de un proceso del mundo real, y por tanto el grado de simplificación determinará el significado de los resultados simulados. Este razonamiento es particularmente difícil de trasladar a la simulación hidráulica donde aspectos de la escala tan diferentes como la escala de los procesos de flujo y de representación del contorno son considerados conjuntamente incluso en fases de parametrización (e.g. parametrización de la rugosidad). Por una parte, esto es debido a que las decisiones de escala vienen condicionadas entre ellas (e.g. la dimensionalidad del modelo condiciona la escala de representación del contorno) y por tanto interaccionan en sus resultados estrechamente. Y por otra parte, debido a los altos requerimientos numéricos y computacionales de una representación explícita de alta resolución de los procesos de flujo y discretización de la malla. Además, previo a la modelización hidráulica, la superficie del terreno sobre la que el agua fluye debe ser modelizada y por tanto presenta su propia escala de representación, que a su vez dependerá de la escala de los datos topográficos medidos con que se elabora el modelo. En última instancia, esta topografía es la que determina el comportamiento espacial del flujo. Por tanto, la escala de la topografía en sus fases de medición y modelización (resolución de los datos y representación topográfica) previas a su incorporación en el modelo hidráulico producirá a su vez un impacto que se acumulará al impacto global resultante debido a la escala computacional del modelo hidráulico y su dimensión. La comprensión de las interacciones entre las complejas geometrías del contorno y la estructura del flujo utilizando la modelización hidráulica depende de las escalas consideradas en la simplificación de los procesos hidráulicos y del terreno (dimensión del modelo, tamaño de escala computacional y escala de los datos topográficos). La naturaleza de la aplicación del modelo hidráulico (e.g. habitat físico, análisis de riesgo de inundaciones, transporte de sedimentos) determina en primer lugar la escala del estudio y por tanto el detalle de los procesos a simular en el modelo (i.e. la dimensionalidad) y, en consecuencia, la escala computacional a la que se realizarán los cálculos (i.e. resolución computacional). Esta última a su vez determina, el detalle geográfico con que deberá representarse el contorno acorde con la resolución de la malla computacional. La parametrización persigue incorporar en el modelo hidráulico la cuantificación de los procesos y condiciones físicas del sistema natural y por tanto debe incluir no solo aquellos procesos que tienen lugar a la escala de modelización, sino también aquellos que tienen lugar a un nivel subescalar y que deben ser definidos mediante relaciones de escalado con las variables modeladas explícitamente. Dicha parametrización se implementa en la práctica mediante la provisión de datos al modelo, por tanto la escala de los datos geográficos utilizados para parametrizar el modelo no sólo influirá en los resultados, sino también determinará la importancia del comportamiento subescalar del modelo y el modo en que estos procesos deban ser parametrizados (e.g. la variabilidad natural del terreno dentro de la celda de discretización o el flujo en las direcciones laterales y verticales en un modelo unidimensional). En esta tesis, se han utilizado el modelo unidimensional HEC-RAS, (HEC 1998b), un modelo ráster bidimensional de propagación de onda, (Yu 2005) y un esquema tridimensional de volúmenes finitos con un algoritmo de porosidad para incorporar la topografía, (Lane et al. 2004; Hardy et al. 2005). La geometría del contorno viene definida por la escala de representación topográfica (resolución de malla y contenido topográfico), la cual a su vez depende de la escala de la fuente cartográfica. Todos estos factores de escala interaccionan en la respuesta del modelo hidráulico a la topografía. En los últimos años, métodos como el análisis fractal y las técnicas geoestadísticas utilizadas para representar y analizar elementos geográficos (e.g. en la caracterización de superficies (Herzfeld and Overbeck 1999; Butler et al. 2001)), están promoviendo nuevos enfoques en la cuantificación de los efectos de escala (Lam et al. 2004; Atkinson and Tate 2000; Lam et al. 2006) por medio del análisis de la estructura espacial de la variable (e.g. Bishop et al. 2006; Ju et al. 2005; Myint et al. 2004; Weng 2002; Bian and Xie 2004; Southworth et al. 2006; Pozd-nyakova et al. 2005; Kyriakidis and Goodchild 2006). Estos métodos cuantifican tanto el rango de valores de la variable presentes a diferentes escalas como la homogeneidad o heterogeneidad de la variable espacialmente distribuida (Lam et al. 2004). En esta tesis, estas técnicas se han utilizado para analizar el impacto de la topografía sobre la estructura de los resultados hidráulicos simulados. Los datos de teledetección de alta resolución y técnicas GIS también están siendo utilizados para la mejor compresión de los efectos de escala en modelos medioambientales (Marceau 1999; Skidmore 2002; Goodchild 2003) y se utilizan en esta tesis. Esta tesis como corpus de investigación aborda las interacciones de esas escalas en la modelización hidráulica desde un punto de vista global e interrelacionado. Sin embargo, la estructura y el foco principal de los experimentos están relacionados con las nociones espaciales de la escala de representación en relación con una visión global de las interacciones entre escalas. En teoría, la representación topográfica debe caracterizar la superficie sobre la que corre el agua a una adecuada (conforme a la finalidad y dimensión del modelo) escala de discretización, de modo que refleje los procesos de interés. La parametrización de la rugosidad debe de reflejar los efectos de la variabilidad de la superficie a escalas de más detalle que aquellas representadas explícitamente en la malla topográfica (i.e. escala de discretización). Claramente, ambos conceptos están físicamente relacionados por un

Hybrid topological derivative and gradient-based methods for electrical impedance tomography

We present a technique to reconstruct the electromagnetic properties of a medium or a set of objects buried inside it from boundary measurements when applying electric currents through a set of electrodes. The electromagnetic parameters may be recovered by means of a gradient method without a priori information on the background. The shape, location and size of objects, when present, are determined by a topological derivative-based iterative procedure. The combination of both strategies allows improved reconstructions of the objects and their properties, assuming a known background.

Diffusion Gradient Temporal Difference for Cooperative Reinforcement Learning with Linear Function Approximation

We introduce a diffusion-based algorithm in which multiple agents cooperate to predict a common and global statevalue function by sharing local estimates and local gradient information among neighbors. Our algorithm is a fully distributed implementation of the gradient temporal difference with linear function approximation, to make it applicable to multiagent settings. Simulations illustrate the benefit of cooperation in learning, as made possible by the proposed algorithm.

Design of spherical symmetric gradient index lenses

Spherical symmetric refractive index distributions also known as Gradient Index lenses such as the Maxwell-Fish-Eye (MFE), the Luneburg or the Eaton lenses have always played an important role in Optics. The recent development of the technique called Transformation Optics has renewed the interest in these gradient index lenses. For instance, Perfect Imaging within the Wave Optics framework has recently been proved using the MFE distribution. We review here the design problem of these lenses, classify them in two groups (Luneburg moveable-limits and fixed-limits type), and establish a new design techniques for each type of problem.

On the design of spherical gradient index lenses

Classical spherical gradient index (GRIN) lenses (such as Maxwell Fish Eye lens, Eaton lens, Luneburg lens, etc.) design procedure using the Abel integral equation is reviewed and reorganized. Each lens is fully defined by a function called the angle of flight which describes the ray deflection through the lens. The radial refractive index distribution is obtained by applying a linear integral transformation to the angle of flight. The interest of this formulation is in the linearity of the integral transformation which allows us to derive new solutions from linear combinations of known lenses. Beside the review of the classical GRIN designs, we present a numerical method for GRIN lenses defined by the Abel integral equation with fixed limits, which is an ill-posed problem.

Instabilities in two-liquid layers subject to a horizontal temperature gradient

We study theoretically the stability of two superposed fluid layers heated laterally. The fluids are supposed to be immiscible, the interface undeformable and of infinite horizontal extension. Combined thermocapillary and buoyancy forces give rise to a basic flow when a temperature difference is applied. The calculations are performed for a melt of GaAs under a layer of molten B2 O3 , a configuration of considerable technological importance. Four dif- ferent flow patterns and five temperature configurations are found for the basic state in this system. A linear stability analysis shows that the basic state may be destabilized by oscilla- tory motions leading to the so-called hydrothermal waves. Depending on the relative height of the two layers these hydrothermal waves propagate parallel or perpendicular to the temperature gradient. This analysis reveals that these perturbations can alter significantly the liquid flow in the liquid-encapsulated crystal growth techniques.

The application of inverse-dispersion and gradient methods to estimate ammonia emissions from a penguin colony.

Penguin colonies represent some of the most concentrated sources of ammonia emissions to the atmosphere in the world. The ammonia emitted into the atmosphere can have a large influence on the nitrogen cycling of ecosystems near the colonies. However, despite the ecological importance of the emissions, no measurements of ammonia emissions from penguin colonies have been made. The objective of this work was to determine the ammonia emission rate of a penguin colony using inverse-dispersion modelling and gradient methods. We measured meteorological variables and mean atmospheric concentrations of ammonia at seven locations near a colony of Adélie penguins in Antarctica to provide input data for inverse-dispersion modelling. Three different atmospheric dispersion models (ADMS, LADD and a Lagrangian stochastic model) were used to provide a robust emission estimate. The Lagrangian stochastic model was applied both in ‘forwards’ and ‘backwards’ mode to compare the difference between the two approaches. In addition, the aerodynamic gradient method was applied using vertical profiles of mean ammonia concentrations measured near the centre of the colony. The emission estimates derived from the simulations of the three dispersion models and the aerodynamic gradient method agreed quite well, giving a mean emission of 1.1 g ammonia per breeding pair per day (95% confidence interval: 0.4–2.5 g ammonia per breeding pair per day). This emission rate represents a volatilisation of 1.9% of the estimated nitrogen excretion of the penguins, which agrees well with that estimated from a temperature-dependent bioenergetics model. We found that, in this study, the Lagrangian stochastic model seemed to give more reliable emission estimates in ‘forwards’ mode than in ‘backwards’ mode due to the assumptions made.

A gradient-enhanced continuum damage model for fibre-reinforced materials

Modelo de daño no local definido a materiales fibrados. Este modelo se aplica al estudio de problemas típicos en la biomecánica de los tejidos blandos, como las paredes arteriales.

Surveillance of habitats and plant diversity indicators across a regional gradient in the Iberian Peninsula

Dentro del Proyecto EBONE (Red de Observación de la Biodiversidad Europea) se analizan diferentes tipos de paisaje en varias zonas de Madrid y norte de Portugal. Se realiza un estudio de los habitats y la diversidad de especies con el objetivo principal de preservarlos y conservalos.

Grain size gradient length scale in ballistic properties optimization of functionally graded nanocrystalline steel plates

The last few years have highlighted the existence of two relevant length scales in the quest to ultrahigh-strength polycrystalline metals. Whereas the microstructural length scale – e.g. grain or twin size – has mainly be linked to the well-established Hall–Petch relationship, the sample length scale – e.g. nanopillar size – has also proven to be at least as relevant, especially in microscale structures. In this letter, a series of ballistic tests on functionally graded nanocrystalline plates are used as a basis for the justification of a “grain size gradient length scale” as an additional ballistic properties optimization parameter.

HOG-Like gradient-based descriptor for visual vehicle detection

One of the main challenges for intelligent vehicles is the capability of detecting other vehicles in their environment, which constitute the main source of accidents. Specifically, many methods have been proposed in the literature for video-based vehicle detection. Most of them perform supervised classification using some appearance-related feature, in particular, symmetry has been extensively utilized. However, an in-depth analysis of the classification power of this feature is missing. As a first contribution of this paper, a thorough study of the classification performance of symmetry is presented within a Bayesian decision framework. This study reveals that the performance of symmetry-based classification is very limited. Therefore, as a second contribution, a new gradient-based descriptor is proposed for vehicle detection. This descriptor exploits the known rectangular structure of vehicle rears within a Histogram of Gradients (HOG)-based framework. Experiments show that the proposed descriptor outperforms largely symmetry as a feature for vehicle verification, achieving classification rates over 90%.

Technical note: Comparison of automated ribosomal intergenic spacer analysis (ARISA) and denaturing gradient gel electrophoresis (DGGE) to assess bacterial diversity in the rumen of sheep

The aim of this study was to compare automated ribosomal intergenic spacer analysis (ARISA) and denaturing gradient gel electrophoresis (DGGE) techniques to assess bacterial diversity in the rumen of sheep. Sheep were fed 2 diets with 70% of either alfalfa hay or grass hay, and the solid (SOL) and liquid (LIQ) phases of the rumen were sampled immediately before feeding (0 h) and at 4 and 8 h postfeeding. Both techniques detected similar differences between forages, with alfalfa hay promoting greater (P < 0.05) bacterial diversity than grass hay. In contrast, whereas ARISA analysis showed a decrease (P < 0.05) of bacterial diversity in SOL at 4 h postfeeding compared with 0 and 8 h samplings, no variations (P > 0.05) over the postfeeding period were detected by DGGE. The ARISA technique showed lower (P < 0.05) bacterial diversity in SOL than in LIQ samples at 4 h postfeeding, but no differences (P > 0.05) in bacterial diversity between both rumen phases were detected by DGGE. Under the conditions of this study, the DGGE was not sensitive enough to detect some changes in ruminal bacterial communities, and therefore ARISA was considered more accurate for assessing bacterial diversity of ruminal samples. The results highlight the influence of the fingerprinting technique used to draw conclusions on factors affecting ruminal bacterial diversity.

A gradient-enhanced large-deformation continuum damage model for fibre-reinforced materials

A non-local gradient-based damage formulation within a geometrically non-linear setting is presented. The hyperelastic constitutive response at local material point level is governed by a strain energy which is additively composed of an isotropic matrix and of an anisotropic fibre-reinforced material, respectively. The inelastic constitutive response is governed by a scalar [1–d]-type damage formulation, where only the anisotropic elastic part is assumed to be affected by the damage. Following the concept in Dimitrijević and Hackl [28], the local free energy function is enhanced by a gradient-term. This term essentially contains the gradient of the non-local damage variable which, itself, is introduced as an additional independent variable. In order to guarantee the equivalence between the local and non-local damage variable, a penalisation term is incorporated within the free energy function. Based on the principle of minimum total potential energy, a coupled system of Euler–Lagrange equations, i.e., the balance of linear momentum and the balance of the non-local damage field, is obtained and solved in weak form. The resulting coupled, highly non-linear system of equations is symmetric and can conveniently be solved by a standard incremental-iterative Newton–Raphson-type solution scheme. Several three-dimensional displacement- and force-driven boundary value problems—partially motivated by biomechanical application—highlight the mesh-objective characteristics and constitutive properties of the model and illustratively underline the capabilities of the formulation proposed