Systematic Process for Building a Fault Diagnoser Based on Petri Nets Applied to a Helicopter

This work presents a systematic process for building a Fault Diagnoser (FD), based on Petri Nets (PNs) which has been applied to a small helicopter. This novel tool is able to detect both intermittent and permanent faults. The work carried out is discussed from theoretical and practical point of view. The procedure begins with a division of the whole system into subsystems, which are the devices that have to be modeled by using PN, considering both the normal and fault operations. Subsequently, the models are integrated into a global Petri Net diagnoser (PND) that is able to monitor a whole helicopter and show critical variables to the operator in order to determine the UAV health, preventing accidents in this manner. A Data Acquisition System (DAQ) has been designed for collecting data during the flights and feeding PN diagnoser with them. Several real flights (nominal or under failure) have been carried out to perform the diagnoser setup and verify its performance. A summary of the validation results obtained during real flight tests is also included. An extensive use of this tool will improve preventive maintenance protocols for UAVs (especially helicopters) and allow establishing recommendations in regulations

Simulación de componentes no estacionarias de viento en orografías complejas

Realistic operation of helicopter flight simulators in complex topographies (such as urban environments) requires appropriate prediction of the incoming wind, and this prediction should be made in real time. Unfortunately, the wind topology around complex topographies shows time-dependent, fully nonlinear, turbulent patterns (i.e., wakes) whose simulation cannot be made using computationally inexpensive tools based on corrected potential approximations. Instead, the full Navier-Stokes plus some kind of turbulent modeling is necessary, which is quite computationally expensive. The complete unsteady flow depends on two parameters, namely the velocity and orientation of the free stream flow. The aim of this MSc thesis is to develop a methodology for the real time simulation of these complex flows. For simplicity, the flow around a single building (20 mx20 m cross section and 100 m height) is considered, with free stream velocity in the range 5-25 m/s. Because of the square cross section, the problem shows two reflection symmetries, which allows for restricting the orientations to the range 0° < a. < 45°. The methodology includes an offline preprocess and the online operation. The preprocess consists in three steps: An appropriate, unstructured mesh is selected in which the flow is sim¬ulated using OpenFOAM, and this is done for 33 combinations of 3 free stream intensities and 11 orientations. For each of these, the simulation proceeds for a sufficiently large time as to eliminate transients. This step is quite computationally expensive. Each flow field is post-processed using a combination of proper orthogonal decomposition, fast Fourier transform, and a convenient optimization tool, which identifies the relevant frequencies (namely, both the basic frequencies and their harmonics) and modes in the computational mesh. This combination includes several new ingredients to filter errors out and identify the relevant spatio-temporal patterns. Note that, in principle, the basic frequencies depend on both the intensity and the orientation of the free stream flow. The outcome of this step is a set of modes (vectors containing the three velocity components at all mesh points) for the various Fourier components, intensities, and orientations, which can be organized as a third order tensor. This step is fairly computationally inexpensive. The above mentioned tensor is treated using a combination of truncated high order singular value, decomposition and appropriate one-dimensional interpolation (as in Lorente, Velazquez, Vega, J. Aircraft, 45 (2008) 1779-1788). The outcome is a tensor representation of both the relevant fre¬quencies and the associated Fourier modes for a given pair of values of the free stream flow intensity and orientation. This step is fairly compu¬tationally inexpensive. The online, operation requires just reconstructing the time-dependent flow field from its Fourier representation, which is extremely computationally inex¬pensive. The whole method is quite robust.

Vibration reduction for vision systems on board unmanned aerial vehicles using a neuro-fuzzy controller

In this paper, an intelligent control approach based on neuro-fuzzy systems performance is presented, with the objective of counteracting the vibrations that affect the low-cost vision platform onboard an unmanned aerial system of rotating nature. A scaled dynamical model of a helicopter is used to simulate vibrations on its fuselage. The impact of these vibrations on the low-cost vision system will be assessed and an intelligent control approach will be derived in order to reduce its detrimental influence. Different trials that consider a neuro-fuzzy approach as a fundamental part of an intelligent semi-active control strategy have been carried out. Satisfactory results have been achieved compared to those obtained by means of vibration reduction passive techniques.

Autonomous Landing of an Unmanned Aerial Vehicle using Image-Based Fuzzy Control

This paper presents a vision based autonomous landing control approach for unmanned aerial vehicles (UAV). The 3D position of an unmanned helicopter is estimated based on the homographies estimated of a known landmark. The translation and altitude estimation of the helicopter against the helipad position are the only information that is used to control the longitudinal, lateral and descend speeds of the vehicle. The control system approach consists in three Fuzzy controllers to manage the speeds of each 3D axis of the aircraft s coordinate system. The 3D position estimation was proven rst, comparing it with the GPS + IMU data with very good results. The robust of the vision algorithm against occlusions was also tested. The excellent behavior of the Fuzzy control approach using the 3D position estimation based in homographies was proved in an outdoors test using a real unmanned helicopter.

Investigación experimental del flujo aerodinámico sobre helipuertos embarcados

La investigación del flujo aerodinámico sobre helipuertos embarcados se encuentra estrechamente relacionada con la operación segura de las aeronaves, pues las condiciones del flujo que tiene lugar en ese entorno pueden exceder los límites para los que están certificadas dichas aeronaves. El ambiente aerodinámico en las inmediaciones de un barco es altamente complejo y se encuentra influenciado por gran número de factores (chimeneas, antenas, mástiles, etc.) relacionados con la configuración específica del propio barco. El flujo objeto de investigación corresponde a la estela que se desarrolla sobre la cubierta de vuelo de una fragata, el cual está fuertemente influenciado por la superestructura de la misma, y que cualitativamente es similar al flujo que tiene lugar entre edificios altos o helipuertos situados en áreas urbanas, pues comprende estructuras tipo caja, con bordes afilados, que generan flujos tridimensionales altamente turbulentos. En esta Tesis se aborda el estudio del problema desde el punto de vista experimental, mediante simulación en túnel aerodinámico y medida de las variables del campo fluido sobre maquetas de fragatas a escala reducida. Las herramientas empleadas para tal cometido, han sido técnicas experimentales, tales como la visualización del flujo, la velocimetría láser por imágenes de partículas, la anemometría láser Doppler y los scanners electrónicos de presión, que han permitido investigar el flujo problema con objeto de obtener información, y adquirir así, un conocimiento más profundo de dicho flujo. La explotación de este conocimiento, ha dado lugar al diseño de una nueva solución, basada en la modificación de geometría básica de la fragata, por medio del cambio de la curvatura del techo del hangar, permitiendo suavizar el escalón descendente que se produce aguas abajo del mismo. Las geometrías modificadas han sido ensayada en túnel mediante la misma metodología empleada para la fragata original, de modo que, ha podido establecerse un análisis comparativo, para valorar la efectividad de la solución propuesta, el cual ha mostrado resultados satisfactorios, retirando el flujo adverso de la zona de operación de helicópteros y desplazándolo hacia el hangar, donde resulta menos peligroso, de modo que se reduce la carga del piloto y los riesgos de accidente durante las operaciones a bordo de embarcaciones. ABSTRACT The investigation of aerodynamic flow above the ship’s heliports is directly related to the aircraft safe operation, because the environment flow conditions may exceed the aircraft certification limits. Aerodynamic ship’s environment is highly complex and it is influenced by a large number of factors (stacks, antennae, masts, …) related to each specific ship configuration. The flow under investigation occurs into the wake produced above the flight deck of a frigate, that is strongly influenced by the superstructure. This flow is similar to one produced around tall buildings or heliports located in urban areas, thus in both of them, the air is flowing around sharp-edges box-like structures, producing three-dimensional and highly turbulent flows. This Thesis studies the problem from an experimental point of view, by means of wind tunnel simulations and measurements of the flow field around reduced scale frigates models. Tools used in this work are the experimental techniques, as flow visualization, particle image velocimetry, laser Doppler anemometry and pressure electronic scanners. These techniques provide information about the flow in order to obtain a more complete insight of this kind of flows. The exploitation of this insight is used for the design of a new flow control concept, based on the modification of the basic frigate geometry. This new design consists in the hangar roof curvature modification that produces a smoothing of the descendent step located downstream the hangar. Modified geometries are tested in wind tunnel by means of the same methodology as the original frigate, thus a comparative analysis is established in order to perform an assessment of effectiveness. This analysis has shown good results in displacing the adverse flow from the helicopter operation path to the nearest hangar region, reducing the pilot load and the accident risks during on board operations.

Toward Visual Autonomous Ship Board Landing of a VTOL UAV

In this paper we tackle the problem of landing a helicopter autonomously on a ship deck, using as the main sensor, an on-board colour camera. To create a test-bed, we first adequately simulate the movement of a ship landing platform on the Sea, for different Sea States, for different ships, randomly and realistically enough. We use a commercial parallel robot to get this movement. Once we had this, we developed an accurate and robust computer vision system to measure the pose of the helipad with respect to the on-board camera. To deal with the noise and the possible fails of the computer vision, a state estimator was created. With all of this, we are now able to develop and test a controller that closes the loop and finish the autonomous landing task.

Thinking way out of the box

l objeto de este trabajo es investigar sobre la arquitectura futurista mediante la figura de Jan Kaplický, el cual realizó planteamientos y arquitecturas que todavía hoy son realmente innovadoras e impactantes, centrando el tema en sus propuestas de vanguardia sobre lo doméstico. La obra elegida para este análisis es la House for a Helicopter Pilot (1979), una arquitectura nómada y cinética en que se habitaría una cápsula modular que puede elevar o bajar sus brazos hidráulicos y luego, una vez cansado el usuario del entorno, podría abandonarlo y encontrar otro lugar salvaje en que situarse. Al ser una obra no construida y utópica, sobre la que no hay apenas documentación, se propone como objetivo indagar sobre esta arquitectura alternativa que hoy en día sigue resultando innovadora, y realizar hipótesis explorando los detalles y objetos que aparecen en la escasa documentación existente, profundizando en las ideas utópicas de Jan Kaplicky

A panel method free-wake code for aeroelastic rotor predictions

A panel method free-wake model to analyse the rotor flapping is presented. The aerodynamic model consists of a panel method, which takes into account the three-dimensional rotor geometry, and a free-wake model, to determine the wake shape. The main features of the model are the wake division into a near-wake sheet and a far wake represented by a single tip vortex, and the modification of the panel method formulation to take into account this particular wake description. The blades are considered rigid with a flap degree of freedom. The problem solution is approached using a relaxation method, which enforces periodic boundary conditions. Finally, several code validations against helicopter and wind turbine experimental data are performed, showing good agreement

Las Redes de Petri Interpretadas en el Diagnóstico de Fallos de Sistemas Híbridos. Aplicación a un Helicóptero no Tripulado

La seguridad y fiabilidad de los procesos industriales son la principal preocupación de los ingenieros encargados de las plantas industriales. Por lo tanto, desde un punto de vista económico, el objetivo principal es reducir el costo del mantenimiento, el tiempo de inactividad y las pérdidas causadas por los fallos. Por otra parte, la seguridad de los operadores, que afecta a los aspectos sociales y económicos, es el factor más relevante a considerar en cualquier sistema Debido a esto, el diagnóstico de fallos se ha convertido en un foco importante de interés para los investigadores de todo el mundo e ingenieros en la industria. Los principales trabajos enfocados en detección de fallos se basan en modelos de los procesos. Existen diferentes técnicas para el modelado de procesos industriales tales como máquinas de estado, árboles de decisión y Redes de Petri (RdP). Por lo tanto, esta tesis se centra en el modelado de procesos utilizando redes de petri interpretadas. Redes de Petri es una herramienta usada en el modelado gráfico y matemático con la habilidad para describir información de los sistemas de una manera concurrente, paralela, asincrona, distribuida y no determinística o estocástica. RdP son también una herramienta de comunicación visual gráfica útil como lo son las cartas de flujo o diagramas de bloques. Adicionalmente, las marcas de las RdP simulan la dinámica y concurrencia de los sistemas. Finalmente, ellas tienen la capacidad de definir ecuaciones de estado específicas, ecuaciones algebraicas y otros modelos que representan el comportamiento común de los sistemas. Entre los diferentes tipos de redes de petri (Interpretadas, Coloreadas, etc.), este trabajo de investigación trata con redes de petri interpretadas principalmente debido a características tales como sincronización, lugares temporizados, aparte de su capacidad para procesamiento de datos. Esta investigación comienza con el proceso para diseñar y construir el modelo y diagnosticador para detectar fallos definitivos, posteriormente, la dinámica temporal fue adicionada para detectar fallos intermitentes. Dos procesos industriales, concretamente un HVAC (Calefacción, Ventilación y Aire Acondicionado) y un Proceso de Envasado de Líquidos fueron usados como banco de pruebas para implementar la herramienta de diagnóstico de fallos (FD) creada. Finalmente, su capacidad de diagnóstico fue ampliada en orden a detectar fallos en sistemas híbridos. Finalmente, un pequeño helicóptero no tripulado fue elegido como ejemplo de sistema donde la seguridad es un desafío, y las técnicas de detección de fallos desarrolladas en esta tesis llevan a ser una herramienta valorada, desde que los accidentes de las aeronaves no tripuladas (UAVs) envuelven un alto costo económico y son la principal razón para introducir restricciones de volar sobre áreas pobladas. Así, este trabajo introduce un proceso sistemático para construir un Diagnosticador de Fallos del sistema mencionado basado en RdR Esta novedosa herramienta es capaz de detectar fallos definitivos e intermitentes. El trabajo realizado es discutido desde un punto de vista teórico y práctico. El procedimiento comienza con la división del sistema en subsistemas para seguido integrar en una RdP diagnosticadora global que es capaz de monitorear el sistema completo y mostrar las variables críticas al operador en orden a determinar la salud del UAV, para de esta manera prevenir accidentes. Un Sistema de Adquisición de Datos (DAQ) ha sido también diseñado para recoger datos durante los vuelos y alimentar la RdP diagnosticadora. Vuelos reales realizados bajo condiciones normales y de fallo han sido requeridos para llevar a cabo la configuración del diagnosticador y verificar su comportamiento. Vale la pena señalar que un alto riesgo fue asumido en la generación de fallos durante los vuelos, a pesar de eso esto permitió recoger datos básicos para desarrollar el diagnóstico de fallos, técnicas de aislamiento, protocolos de mantenimiento, modelos de comportamiento, etc. Finalmente, un resumen de la validación de resultados obtenidos durante las pruebas de vuelo es también incluido. Un extensivo uso de esta herramienta mejorará los protocolos de mantenimiento para UAVs (especialmente helicópteros) y permite establecer recomendaciones en regulaciones. El uso del diagnosticador usando redes de petri es considerado un novedoso enfoque. ABSTRACT Safety and reliability of industrial processes are the main concern of the engineers in charge of industrial plants. Thus, from an economic point of view, the main goal is to reduce the maintenance downtime cost and the losses caused by failures. Moreover, the safety of the operators, which affects to social and economic aspects, is the most relevant factor to consider in any system. Due to this, fault diagnosis has become a relevant focus of interest for worldwide researchers and engineers in the industry. The main works focused on failure detection are based on models of the processes. There are different techniques for modelling industrial processes such as state machines, decision trees and Petri Nets (PN). Thus, this Thesis is focused on modelling processes by using Interpreted Petri Nets. Petri Nets is a tool used in the graphic and mathematical modelling with ability to describe information of the systems in a concurrent, parallel, asynchronous, distributed and not deterministic or stochastic manner. PNs are also useful graphical visual communication tools as flow chart or block diagram. Additionally, the marks of the PN simulate the dynamics and concurrence of the systems. Finally, they are able to define specific state equations, algebraic equations and other models that represent the common behaviour of systems. Among the different types of PN (Interpreted, Coloured, etc.), this research work deals with the interpreted Petri Nets mainly due to features such as synchronization capabilities, timed places, apart from their capability for processing data. This Research begins with the process for designing and building the model and diagnoser to detect permanent faults, subsequently, the temporal dynamic was added for detecting intermittent faults. Two industrial processes, namely HVAC (Heating, Ventilation and Air Condition) and Liquids Packaging Process were used as testbed for implementing the Fault Diagnosis (FD) tool created. Finally, its diagnostic capability was enhanced in order to detect faults in hybrid systems. Finally, a small unmanned helicopter was chosen as example of system where safety is a challenge and fault detection techniques developed in this Thesis turn out to be a valuable tool since UAVs accidents involve high economic cost and are the main reason for setting restrictions to fly over populated areas. Thus, this work introduces a systematic process for building a Fault Diagnoser of the mentioned system based on Petri Nets. This novel tool is able to detect both intermittent and permanent faults. The work carried out is discussed from theoretical and practical point of view. The procedure begins with a division of the system into subsystems for further integration into a global PN diagnoser that is able to monitor the whole system and show critical variables to the operator in order to determine the UAV health, preventing accidents in this manner. A Data Acquisition System (DAQ) has been also designed for collecting data during the flights and feed PN Diagnoser. Real flights carried out under nominal and failure conditions have been required to perform the diagnoser setup and verify its performance. It is worth noting that a high risk was assumed in the generation of faults during the flights, nevertheless this allowed collecting basic data so as to develop fault diagnosis, isolations techniques, maintenance protocols, behaviour models, etc. Finally, a summary of the validation results obtained during real flight tests is also included. An extensive use of this tool will improve preventive maintenance protocols for UAVs (especially helicopters) and allow establishing recommendations in regulations. The use of the diagnoser by using Petri Nets is considered as novel approach.

An engineering modification of the blade element momentum combination applicable in vertical descent flight :fundamentals and validation

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non‐linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

An engineering modification of the blade element momentum equation for vertical descent : an autoration case study

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non-linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

Discrete linear stability and sensitivity analysis of fluid flows

Este trabajo presenta un método discreto para el cálculo de estabilidad hidrodinámica y análisis de sensibilidad a perturbaciones externas para ecuaciones diferenciales y en particular para las ecuaciones de Navier-Stokes compressible. Se utiliza una aproximación con variable compleja para obtener una precisión analítica en la evaluación de la matriz Jacobiana. Además, mapas de sensibilidad para la sensibilidad a las modificaciones del flujo de base y a una fuerza constante permiten identificar las regiones del campo fluido donde una modificacin (ej. fuerza puntual) tiene un efecto estabilizador del flujo. Se presentan cuatro casos de prueba: (1) un caso analítico para comprobar la derivación discreta, (2) una cavidad cerrada a bajo Reynolds para mostrar la mayor precisión en el cálculo de los valores propios con la aproximación de paso complejo, (3) flujo 2D en un cilindro circular para validar la metodología, y (4) flujo en un cavidad abierta, presentado para validar el método en casos de inestabilidades convectivamente inestables. Los tres últimos casos mencionados (2-4) se resolvieron con las ecuaciones de Navier-Stokes compresibles, utilizando un método Discontinuous Galerkin Spectral Element Method. Se obtuvo una buena concordancia para el caso de validación (3), cuando se comparó el nuevo método con resultados de la literatura. Además, este trabajo muestra que para el cálculo de los modos propios directos y adjuntos, así como para los mapas de sensibilidad, el uso de variables complejas es de suprema importancia para obtener una predicción precisa. El método descrito es aplicado al análisis para la estabilización de la estela generada por un disco actuador, que representa un modelo sencillo para hélices, rotores de helicópteros o turbinas eólicas. Se explora la primera bifurcación del flujo para un disco actuador, y se sugiere que está asociada a una inestabilidad de tipo Kelvin-Helmholtz, cuya estabilidad se controla con en el número de Reynolds y en la resistencia del disco actuador (o fuerza resistente). En primer lugar, se verifica que la disminución de la resistencia del disco tiene un efecto estabilizador parecido a una disminución del Reynolds. En segundo lugar, el análisis hidrodinmico discreto identifica dos regiones para la colocación de una fuerza puntual que controle las inestabilidades, una cerca del disco y otra en una zona aguas abajo. En tercer lugar, se muestra que la inclusión de un forzamiento localizado cerca del actuador produce una estabilización más eficiente que al forzar aguas abajo. El análisis de los campos de flujo controlados confirma que modificando el gradiente de velocidad cerca del actuador es más eficiente para estabilizar la estela. Estos resultados podrían proporcionar nuevas directrices para la estabilización de la estela de turbinas de viento o de marea cuando estén instaladas en un parque eólico y minimizar las interacciones no estacionarias entre turbinas. ABSTRACT A discrete framework for computing the global stability and sensitivity analysis to external perturbations for any set of partial differential equations is presented. In particular, a complex-step approximation is used to achieve near analytical accuracy for the evaluation of the Jacobian matrix. Sensitivity maps for the sensitivity to base flow modifications and to a steady force are computed to identify regions of the flow field where an input could have a stabilising effect. Four test cases are presented: (1) an analytical test case to prove the theory of the discrete framework, (2) a lid-driven cavity at low Reynolds case to show the improved accuracy in the calculation of the eigenvalues when using the complex-step approximation, (3) the 2D flow past a circular cylinder at just below the critical Reynolds number is used to validate the methodology, and finally, (4) the flow past an open cavity is presented to give an example of the discrete method applied to a convectively unstable case. The latter three (2–4) of the aforementioned cases were solved with the 2D compressible Navier–Stokes equations using a Discontinuous Galerkin Spectral Element Method. Good agreement was obtained for the validation test case, (3), with appropriate results in the literature. Furthermore, it is shown that for the calculation of the direct and adjoint eigenmodes and their sensitivity maps to external perturbations, the use of complex variables is paramount for obtaining an accurate prediction. An analysis for stabilising the wake past an actuator disc, which represents a simple model for propellers, helicopter rotors or wind turbines is also presented. We explore the first flow bifurcation for an actuator disc and it suggests that it is associated to a Kelvin- Helmholtz type instability whose stability relies on the Reynolds number and the flow resistance applied through the disc (or actuator forcing). First, we report that decreasing the disc resistance has a similar stabilising effect to an decrease in the Reynolds number. Second, a discrete sensitivity analysis identifies two regions for suitable placement of flow control forcing, one close to the disc and one far downstream where the instability originates. Third, we show that adding a localised forcing close to the actuator provides more stabilisation that forcing far downstream. The analysis of the controlled flow fields, confirms that modifying the velocity gradient close to the actuator is more efficient to stabilise the wake than controlling the sheared flow far downstream. An interesting application of these results is to provide guidelines for stabilising the wake of wind or tidal turbines when placed in an energy farm to minimise unsteady interactions.