Environmental assessment of low speed policies for motor vehicle mobility in city centres

streets in local residential areas in large cities, real traffic tests for pollutant emissions and fuel consumption have been carried out in Madrid city centre. Emission concentration and car activity were simultaneously measured by a Portable Emissions Measurement System. Real life tests carried out at different times and on different days were performed with a turbo-diesel engine light vehicle equipped with an oxidizer catalyst and using different driving styles with a previously trained driver. The results show that by reducing the speed limit from 50 km h-1 to 30 km h-1, using a normal driving style, the time taken for a given trip does not increase, but fuel consumption and NOx, CO and PM emissions are clearly reduced. Therefore, the main conclusion of this work is that reducing the speed limit in some narrow streets in residential and commercial areas or in a city not only increases pedestrian safety, but also contributes to reducing the environmental impact of motor vehicles and reducing fuel consumption. In addition, there is also a reduction in the greenhouse gas emissions resulting from the combustion of the fuel.

Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Discriminación del estado de la carretera mediante procesado acústico en vehículo

La rápida adopción de dispositivos electrónicos en el automóvil, ha contribuido a mejorar en gran medida la seguridad y el confort. Desde principios del siglo 20, la investigación en sistemas de seguridad activa ha originado el desarrollo de tecnologías como ABS (Antilock Brake System), TCS (Traction Control System) y ESP (Electronic Stability Program). El coste de despliegue de estos sistemas es crítico: históricamente, sólo han sido ampliamente adoptados cuando el precio de los sensores y la electrónica necesarios para su construcción ha caído hasta un valor marginal. Hoy en día, los vehículos a motor incluyen un amplio rango de sensores para implementar las funciones de seguridad. La incorporación de sistemas que detecten la presencia de agua, hielo o nieve en la vía es un factor adicional que podría ayudar a evitar situaciones de riesgo. Existen algunas implementaciones prácticas capaces de detectar carreteras mojadas, heladas y nevadas, aunque con limitaciones importantes. En esta tesis doctoral, se propone una aproximación novedosa al problema, basada en el análisis del ruido de rodadura generado durante la conducción. El ruido de rodadura es capturado y preprocesado. Después es analizado utilizando un clasificador basado en máquinas de vectores soporte (SVM), con el fin de generar una estimación del estado del firme. Todas estas operaciones se realizan en el propio vehículo. El sistema propuesto se ha desarrollado y evaluado utilizando Matlabr, mostrando tasas de aciertos de más del 90%. Se ha realizado una implementación en tiempo real, utilizando un prototipo basado en DSP. Después se han introducido varias optimizaciones para permitir que el sistema sea realizable usando un microcontrolador de propósito general. Finalmente se ha realizado una implementación hardware basada en un microcontrolador, integrándola estrechamente con las ECU del vehículo, pudiendo obtener datos capturados por los sensores del mismo y enviar las estimaciones del estado del firme. El sistema resultante ha sido patentado, y destaca por su elevada tasa de aciertos con un tamaño, consumo y coste reducidos. ABSTRACT Proliferation of automotive electronics, has greatly improved driving safety and comfort. Since the beginning of the 20th century, investigation in active safety systems has resulted in the development of technologies such as ABS (Antilock Brake System), TCS (Traction Control System) and ESP (Electronic Stability Program). Deployment cost of these systems is critical: historically, they have been widely adopted only when the price of the sensors and electronics needed to build them has been cut to a marginal value. Nowadays, motor vehicles include a wide range of sensors to implement the safety functions. Incorporation of systems capable of detecting water, ice or snow on the road is an additional factor that could help avoiding risky situations. There are some implementations capable of detecting wet, icy and snowy roads, although with important limitations. In this PhD Thesis, a novel approach is proposed, based on the analysis of the tyre/road noise radiated during driving. Tyre/road noise is captured and pre-processed. Then it is analysed using a Support Vector Machine (SVM) based classifier, to output an estimation of the road status. All these operations are performed on-board. Proposed system is developed and evaluated using Matlabr, showing success rates greater than 90%. A real time implementation is carried out using a DSP based prototype. Several optimizations are introduced enabling the system to work using a low-cost general purpose microcontroller. Finally a microcontroller based hardware implementation is developed. This implementation is tightly integrated with the vehicle ECUs, allowing it to obtain data captured by its sensors, and to send the road status estimations. Resulting system has been patented, and is notable because of its high hit rate, small size, low power consumption and low cost.

Evaluation of the influence of toll systems on energy consumption and CO2 emissions: A case study of a Spanish highway

This paper studies the energy consumption and subsequent CO2 emissions of road highway transportation under three toll systems in Spain for four categories of vehicles: cars, vans, buses and articulated trucks. The influence of toll systems is tested for a section of AP-41 highway between Toledo and Madrid. One system is free flow, other is traditional stop and go and the last toll system operates with an electronic toll collection (ETC) technology. Energy consumption and CO2 emissions were found to be closely related to vehicle mass, wind exposure, engine efficiency and acceleration rate. These parameters affect, directly or indirectly, the external forces which determine the energy consumption. Reducing the magnitude of these forces through an appropriate toll management is an important way of improving the energy performance of vehicles. The type of toll system used can have a major influence on the energy efficiency of highway transportation and therefore it is necessary to consider free flow.

SERVICE NEEDS FORECASTING: An Approach for the Motor Industry Using Analogies with Medical ER Management Models.

During the past years, the industry has shifted position and moved towards “the luxury universe” whose customers are demanding, treating individuals as unique and valued customer for the business, offering vehicles produced with the state of the art technologies and implementing the highest finishing standards. Due to the competitive level in the market, motor makers enable processes which equalizes customer services to E.R. management, being dealt with the maximum urgency that allows the comparison between both, car workshops and emergency rooms, where workshop bays or ramps will be equal to emergency boxes and skilled technicians are equivalent to the health care specialist, who will carry out tests and checks prior to afford any final operation, keeping the “patient” under control before it is back to normal utilization. This paper ratify a valid model for the automotive industry to estimate customer service demand forecasting under variable demand conditions using analogies with patient demand models used for the medical ER

Driving assistance system applied in curves for real vehicles | Sistema de ayuda a la conducción en curvas para vehículos reales

Decreasing the accidents on highway and urban environments is the main motivation for the research and developing of driving assistance systems, also called ADAS (Advanced Driver Assistance Systems). In recent years, there are many applications of these systems in commercial vehicles: ABS systems, Cruise Control (CC), parking assistance and warning systems (including GPS), among others. However, the implementation of driving assistance systems on the steering wheel is more limited, because of their complexity and sensitivity. This paper is focused in the development, test and implementation of a driver assistance system for controlling the steering wheel in curve zones. This system is divided in two levels: an inner control loop which permits to execute the position and speed target, softening the action over the steering wheel, and a second control outer loop (controlling for fuzzy logic) that sends the reference to the inner loop according the environment and vehicle conditions. The tests have been done in different curves and speeds. The system has been proved in a commercial vehicle with satisfactory results.

Analysis of road safety incentives in highway concessions in Spain

Public Private Partnerships (PPPs) are mostly implemented for three reasons: to circumvent budgetary constraints, encourage efficiency and improvement of quality in the provision of public infrastructure. One of the ways of reaching the latter objective is by the introduction of performance-based standards tied to bonuses and penalties to reward or punish the performance of the contractor. These performance based standards often refer to different aspects such as technical, environmental and safety issues. This paper focuses on the implementation of safety based incentives in PPPs. The main aim of this paper is to analyze whether the incentives to improve road safety in PPPs are effective in improving safety ratios in Spain. To this end, negative binomial regression models have been applied using information from the Spanish high capacity network in 2006. The findings indicate that even though road safety is highly influenced by variables that are not much controllable by the contractor such as the Average Annual Daily Traffic and the percentage of heavy vehicles in the highway, the implementation of safety incentives in PPPs has a positive influence in the reduction of fatalities, injuries and accidents.

Analysis of road safety incentives in highway concessions in Spain

Public Private Partnerships (PPPs) are mostly implemented for three reasons: to circumvent budgetary constraints, encourage efficiency and improvement of quality in the provision of public infrastructure. One of the ways of reaching the latter objective is by the introduction of performance-based standards tied to bonuses and penalties to reward or punish the performance of the contractor. These performance based standards often refer to different aspects such as technical, environmental and safety issues. This paper focuses on the implementation of safety based incentives in PPPs. The main aim of this paper is to analyze whether the incentives to improve road safety in PPPs are effective in improving safety ratios in Spain. To this end, negative binomial regression models have been applied using information from the Spanish high capacity network in 2006. The findings indicate that even though road safety is highly influenced by variables that are not much controllable by the contractor such as the Average Annual Daily Traffic and the percentage of heavy vehicles in the highway, the implementation of safety incentives in PPPs has a positive influence in the reduction of fatalities, injuries and accidents.