Plasma–wall interaction in laser inertial fusion reactors: novel proposals for radiation tests of first wall materials

Dry-wall laser inertial fusion (LIF) chambers will have to withstand strong bursts of fast charged particles which will deposit tens of kJ m−2 and implant more than 1018 particles m−2 in a few microseconds at a repetition rate of some Hz. Large chamber dimensions and resistant plasma-facing materials must be combined to guarantee the chamber performance as long as possible under the expected threats: heating, fatigue, cracking, formation of defects, retention of light species, swelling and erosion. Current and novel radiation resistant materials for the first wall need to be validated under realistic conditions. However, at present there is a lack of facilities which can reproduce such ion environments. This contribution proposes the use of ultra-intense lasers and high-intense pulsed ion beams (HIPIB) to recreate the plasma conditions in LIF reactors. By target normal sheath acceleration, ultra-intense lasers can generate very short and energetic ion pulses with a spectral distribution similar to that of the inertial fusion ion bursts, suitable to validate fusion materials and to investigate the barely known propagation of those bursts through background plasmas/gases present in the reactor chamber. HIPIB technologies, initially developed for inertial fusion driver systems, provide huge intensity pulses which meet the irradiation conditions expected in the first wall of LIF chambers and thus can be used for the validation of materials too.

Plasma–wall interaction in laser inertial fusion reactors: novel proposals for radiation tests of first wall materials

Dry-wall laser inertial fusion (LIF) chambers will have to withstand strong bursts of fast charged particles which will deposit tens of kJ m−2 and implant more than 1018 particles m−2 in a few microseconds at a repetition rate of some Hz. Large chamber dimensions and resistant plasma-facing materials must be combined to guarantee the chamber performance as long as possible under the expected threats: heating, fatigue, cracking, formation of defects, retention of light species, swelling and erosion. Current and novel radiation resistant materials for the first wall need to be validated under realistic conditions. However, at present there is a lack of facilities which can reproduce such ion environments. This contribution proposes the use of ultra-intense lasers and high-intense pulsed ion beams (HIPIB) to recreate the plasma conditions in LIF reactors. By target normal sheath acceleration, ultra-intense lasers can generate very short and energetic ion pulses with a spectral distribution similar to that of the inertial fusion ion bursts, suitable to validate fusion materials and to investigate the barely known propagation of those bursts through background plasmas/gases present in the reactor chamber. HIPIB technologies, initially developed for inertial fusion driver systems, provide huge intensity pulses which meet the irradiation conditions expected in the first wall of LIF chambers and thus can be used for the validation of materials too.

Diffusion Issues of Heat and Light Species in Laser Fusion Devices

There are several heat and mass diffusion problems which affect to the IFC chamber design. New simulation models and experiments are needed to take into account the extreme conditions due to ignition pulses and neutron flux

Fracture micromechanisms and residual stresses of a highly resistant duplex stainless steel

The paper presents some preliminary results of an ongoing research intended to qualify a highly resistant duplex stainless steel wire as prestressing steel and, gets on insight on (he wires' fracture micromechanism and residual stresses field. SEM fractographic analysis of the stainless steel wires indicates an anisotropic fracture behavior in tension, in presence of surface flaws, attributed to the residual stresses generated through the fabrication process. The residual stresses magnitude influences the damage tolerance, its knowledge being a key issue in designating/qualifying the wires as prestressing steels.

Development of an Elevated Temperature Loop Heat Pipe for Space Applications and Investigation of Non Condensable Gas Impact on its Performance

Un caloducto en bucle cerrado o Loop Heat Pipe (LHP) es un dispositivo de transferencia de calor cuyo principio de operación se basa en la evaporación/condensación de un fluido de trabajo, que es bombeado a través de un circuito cerrado gracias a fuerzas de capilaridad. Gracias a su flexibilidad, su baja masa y su mínimo (incluso nulo) consumo de potencia, su principal aplicación ha sido identificada como parte del subsistema de control térmico de vehículos espaciales. En el presente trabajo se ha desarrollado un LHP capaz de funcionar eficientemente a temperaturas de hasta 125 oC, siguiendo la actual tendencia de los equipos a bordo de satélites de incrementar su temperatura de operación. En la selección del diseño optimo para dicho LHP, la compatibilidad entre materiales y fluido de trabajo se identificó como uno de los puntos clave. Para seleccionar la mejor combinación, se llevó a cabo una exhaustiva revisión del estado del arte, además de un estudio especifico que incluía el desarrollo de un banco de ensayos de compatibilidad. Como conclusión, la combinación seleccionada como la candidata idónea para ser integrada en el LHP capaz de operar hasta 125 oC fue un evaporador de acero inoxidable, líneas de titanio y amoniaco como fluido de trabajo. En esa línea se diseñó y fabricó un prototipo para ensayos y se desarrolló un modelo de simulación con EcosimPro para evaluar sus prestaciones. Se concluyó que el diseño era adecuado para el rango de operación definido. La incompatibilidad entre el fluido de trabajo y los materiales del LHP está ligada a la generación de gases no condensables. Para un estudio más detallado de los efectos de dichos gases en el funcionamiento del LHP se analizó su comportamiento con diferentes cantidades de nitrógeno inyectadas en su cámara de compensación, simulando un gas no condensable formado en el interior del dispositivo. El estudio se basó en el análisis de las temperaturas medidas experimentalmente a distintos niveles de potencia y temperatura de sumidero o fuente fría. Adicionalmente, dichos resultados se compararon con las predicciones obtenidas por medio del modelo en EcosimPro. Las principales conclusiones obtenidas fueron dos. La primera indica que una cantidad de gas no condensable más de dos veces mayor que la cantidad generada al final de la vida de un satélite típico de telecomunicaciones (15 años) tiene efectos casi despreciables en el funcionamiento del LHP. La segunda es que el principal efecto del gas no condensable es una disminución de la conductancia térmica, especialmente a bajas potencias y temperaturas de sumidero. El efecto es más significativo cuanto mayor es la cantidad de gas añadida. Asimismo, durante la campaña de ensayos se observó un fenómeno no esperado para grandes cantidades de gas no condensable. Dicho fenómeno consiste en un comportamiento oscilatorio, detectado tanto en los ensayos como en la simulación. Este efecto es susceptible de una investigación más profunda y los resultados obtenidos pueden constituir la base para dicha tarea. ABSTRACT Loop Heat Pipes (LHPs) are heat transfer devices whose operating principle is based on the evaporation/condensation of a working fluid, and which use capillary pumping forces to ensure the fluid circulation. Thanks to their flexibility, low mass and minimum (even null) power consumption, their main application has been identified as part of the thermal control subsystem in spacecraft. In the present work, an LHP able to operate efficiently up to 125 oC has been developed, which is in line with the current tendency of satellite on-board equipment to increase their operating temperatures. In selecting the optimal LHP design for the elevated temperature application, the compatibility between the materials and working fluid has been identified as one of the main drivers. An extensive literature review and a dedicated trade-off were performed, in order to select the optimal combination of fluids and materials for the LHP. The trade-off included the development of a dedicated compatibility test stand. In conclusion, the combination of stainless steel evaporator, titanium piping and ammonia as working fluid was selected as the best candidate to operate up to 125 oC. An LHP prototype was designed and manufactured and a simulation model in EcosimPro was developed to evaluate its performance. The first conclusion was that the defined LHP was suitable for the defined operational range. Incompatibility between the working fluid and LHP materials is linked to Non Condensable Gas (NCG) generation. Therefore, the behaviour of the LHP developed with different amounts of nitrogen injected in its compensation chamber to simulate NCG generation, was analyzed. The LHP performance was studied by analysis of the test results at different temperatures and power levels. The test results were also compared to simulations in EcosimPro. Two additional conclusions can be drawn: (i) the effects of an amount of more than two times the expected NCG at the end of life of a typical telecommunications satellite (15 years) is almost negligible on the LHP operation, and (ii) the main effect of the NCG is a decrease in the LHP thermal conductance, especially at low temperatures and low power levels. This decrease is more significant with the progressive addition of NCG. An unexpected phenomenon was observed in the LHP operation with large NCG amounts. Namely, an oscillatory behaviour, which was observed both in the tests and the simulation. This effect provides the basis for further studies concerning oscillations in LHPs.

High power beam dump project for the accelerator prototype LIPAc: Cooling design and analysis

En el campo de la fusión nuclear y desarrollándose en paralelo a ITER (International Thermonuclear Experimental Reactor), el proyecto IFMIF (International Fusion Material Irradiation Facility) se enmarca dentro de las actividades complementarias encaminadas a solucionar las barreras tecnológicas que aún plantea la fusión. En concreto IFMIF es una instalación de irradiación cuya misión es caracterizar materiales resistentes a condiciones extremas como las esperadas en los futuros reactores de fusión como DEMO (DEMOnstration power plant). Consiste de dos aceleradores de deuterones que proporcionan un haz de 125 mA y 40 MeV cada uno, que al colisionar con un blanco de litio producen un flujo neutrónico intenso (1017 neutrones/s) con un espectro similar al de los neutrones de fusión [1], [2]. Dicho flujo neutrónico es empleado para irradiar los diferentes materiales candidatos a ser empleados en reactores de fusión, y las muestras son posteriormente examinadas en la llamada instalación de post-irradiación. Como primer paso en tan ambicioso proyecto, una fase de validación y diseño llamada IFMIFEVEDA (Engineering Validation and Engineering Design Activities) se encuentra actualmente en desarrollo. Una de las actividades contempladas en esta fase es la construcción y operación de una acelarador prototipo llamado LIPAc (Linear IFMIF Prototype Accelerator). Se trata de un acelerador de deuterones de alta intensidad idéntico a la parte de baja energía de los aceleradores de IFMIF. Los componentes del LIPAc, que será instalado en Japón, son suministrados por diferentes países europeos. El acelerador proporcionará un haz continuo de deuterones de 9 MeV con una potencia de 1.125 MW que tras ser caracterizado con diversos instrumentos deberá pararse de forma segura. Para ello se requiere un sistema denominado bloque de parada (Beam Dump en inglés) que absorba la energía del haz y la transfiera a un sumidero de calor. España tiene el compromiso de suministrar este componente y CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) es responsable de dicha tarea. La pieza central del bloque de parada, donde se para el haz de iones, es un cono de cobre con un ángulo de 3.5o, 2.5 m de longitud y 5 mm de espesor. Dicha pieza está refrigerada por agua que fluye en su superficie externa por el canal que se forma entre el cono de cobre y otra pieza concéntrica con éste. Este es el marco en que se desarrolla la presente tesis, cuyo objeto es el diseño del sistema de refrigeración del bloque de parada del LIPAc. El diseño se ha realizado utilizando un modelo simplificado unidimensional. Se han obtenido los parámetros del agua (presión, caudal, pérdida de carga) y la geometría requerida en el canal de refrigeración (anchura, rugosidad) para garantizar la correcta refrigeración del bloque de parada. Se ha comprobado que el diseño permite variaciones del haz respecto a la situación nominal siendo el flujo crítico calorífico al menos 2 veces superior al nominal. Se han realizado asimismo simulaciones fluidodinámicas 3D con ANSYS-CFX en aquellas zonas del canal de refrigeración que lo requieren. El bloque de parada se activará como consecuencia de la interacción del haz de partículas lo que impide cualquier cambio o reparación una vez comenzada la operación del acelerador. Por ello el diseño ha de ser muy robusto y todas las hipótesis utilizadas en la realización de éste deben ser cuidadosamente comprobadas. Gran parte del esfuerzo de la tesis se centra en la estimación del coeficiente de transferencia de calor que es determinante en los resultados obtenidos, y que se emplea además como condición de contorno en los cálculos mecánicos. Para ello por un lado se han buscado correlaciones cuyo rango de aplicabilidad sea adecuado para las condiciones del bloque de parada (canal anular, diferencias de temperatura agua-pared de decenas de grados). En un segundo paso se han comparado los coeficientes de película obtenidos a partir de la correlación seleccionada (Petukhov-Gnielinski) con los que se deducen de simulaciones fluidodinámicas, obteniendo resultados satisfactorios. Por último se ha realizado una validación experimental utilizando un prototipo y un circuito hidráulico que proporciona un flujo de agua con los parámetros requeridos en el bloque de parada. Tras varios intentos y mejoras en el experimento se han obtenido los coeficientes de película para distintos caudales y potencias de calentamiento. Teniendo en cuenta la incertidumbre de las medidas, los valores experimentales concuerdan razonablemente bien (en el rango de 15%) con los deducidos de las correlaciones. Por motivos radiológicos es necesario controlar la calidad del agua de refrigeración y minimizar la corrosión del cobre. Tras un estudio bibliográfico se identificaron los parámetros del agua más adecuados (conductividad, pH y concentración de oxígeno disuelto). Como parte de la tesis se ha realizado asimismo un estudio de la corrosión del circuito de refrigeración del bloque de parada con el doble fin de determinar si puede poner en riesgo la integridad del componente, y de obtener una estimación de la velocidad de corrosión para dimensionar el sistema de purificación del agua. Se ha utilizado el código TRACT (TRansport and ACTivation code) adaptándalo al caso del bloque de parada, para lo cual se trabajó con el responsable (Panos Karditsas) del código en Culham (UKAEA). Los resultados confirman que la corrosión del cobre en las condiciones seleccionadas no supone un problema. La Tesis se encuentra estructurada de la siguiente manera: En el primer capítulo se realiza una introducción de los proyectos IFMIF y LIPAc dentro de los cuales se enmarca esta Tesis. Además se describe el bloque de parada, siendo el diseño del sistema de rerigeración de éste el principal objetivo de la Tesis. En el segundo y tercer capítulo se realiza un resumen de la base teórica así como de las diferentes herramientas empleadas en el diseño del sistema de refrigeración. El capítulo cuarto presenta los resultados del relativos al sistema de refrigeración. Tanto los obtenidos del estudio unidimensional, como los obtenidos de las simulaciones fluidodinámicas 3D mediante el empleo del código ANSYS-CFX. En el quinto capítulo se presentan los resultados referentes al análisis de corrosión del circuito de refrigeración del bloque de parada. El capítulo seis se centra en la descripción del montaje experimental para la obtención de los valores de pérdida de carga y coeficiente de transferencia del calor. Asimismo se presentan los resultados obtenidos en dichos experimentos. Finalmente encontramos un capítulo de apéndices en el que se describen una serie de experimentos llevados a cabo como pasos intermedios en la obtención del resultado experimental del coeficiente de película. También se presenta el código informático empleado para el análisis unidimensional del sistema de refrigeración del bloque de parada llamado CHICA (Cooling and Heating Interaction and Corrosion Analysis). ABSTRACT In the nuclear fusion field running in parallel to ITER (International Thermonuclear Experimental Reactor) as one of the complementary activities headed towards solving the technological barriers, IFMIF (International Fusion Material Irradiation Facility) project aims to provide an irradiation facility to qualify advanced materials resistant to extreme conditions like the ones expected in future fusion reactors like DEMO (DEMOnstration Power Plant). IFMIF consists of two constant wave deuteron accelerators delivering a 125 mA and 40 MeV beam each that will collide on a lithium target producing an intense neutron fluence (1017 neutrons/s) with a similar spectra to that of fusion neutrons [1], [2]. This neutron flux is employed to irradiate the different material candidates to be employed in the future fusion reactors, and the samples examined after irradiation at the so called post-irradiative facilities. As a first step in such an ambitious project, an engineering validation and engineering design activity phase called IFMIF-EVEDA (Engineering Validation and Engineering Design Activities) is presently going on. One of the activities consists on the construction and operation of an accelerator prototype named LIPAc (Linear IFMIF Prototype Accelerator). It is a high intensity deuteron accelerator identical to the low energy part of the IFMIF accelerators. The LIPAc components, which will be installed in Japan, are delivered by different european countries. The accelerator supplies a 9 MeV constant wave beam of deuterons with a power of 1.125 MW, which after being characterized by different instruments has to be stopped safely. For such task a beam dump to absorb the beam energy and take it to a heat sink is needed. Spain has the compromise of delivering such device and CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) is responsible for such task. The central piece of the beam dump, where the ion beam is stopped, is a copper cone with an angle of 3.5o, 2.5 m long and 5 mm width. This part is cooled by water flowing on its external surface through the channel formed between the copper cone and a concentric piece with the latter. The thesis is developed in this realm, and its objective is designing the LIPAc beam dump cooling system. The design has been performed employing a simplified one dimensional model. The water parameters (pressure, flow, pressure loss) and the required annular channel geometry (width, rugoisty) have been obtained guaranteeing the correct cooling of the beam dump. It has been checked that the cooling design allows variations of the the beam with respect to the nominal position, being the CHF (Critical Heat Flux) at least twice times higher than the nominal deposited heat flux. 3D fluid dynamic simulations employing ANSYS-CFX code in the beam dump cooling channel sections which require a more thorough study have also been performed. The beam dump will activateasaconsequenceofthe deuteron beam interaction, making impossible any change or maintenance task once the accelerator operation has started. Hence the design has to be very robust and all the hypotheses employed in the design mustbecarefully checked. Most of the work in the thesis is concentrated in estimating the heat transfer coefficient which is decisive in the obtained results, and is also employed as boundary condition in the mechanical analysis. For such task, correlations which applicability range is the adequate for the beam dump conditions (annular channel, water-surface temperature differences of tens of degrees) have been compiled. In a second step the heat transfer coefficients obtained from the selected correlation (Petukhov- Gnielinski) have been compared with the ones deduced from the 3D fluid dynamic simulations, obtaining satisfactory results. Finally an experimental validation has been performed employing a prototype and a hydraulic circuit that supplies a flow with the requested parameters in the beam dump. After several tries and improvements in the experiment, the heat transfer coefficients for different flows and heating powers have been obtained. Considering the uncertainty in the measurements the experimental values agree reasonably well (in the order of 15%) with the ones obtained from the correlations. Due to radiological reasons the quality of the cooling water must be controlled, hence minimizing the copper corrosion. After performing a bibligraphic study the most adequate water parameters were identified (conductivity, pH and dissolved oxygen concentration). As part of this thesis a corrosion study of the beam dump cooling circuit has been performed with the double aim of determining if corrosion can pose a risk for the copper beam dump , and obtaining an estimation of the corrosion velocitytodimension the water purification system. TRACT code(TRansport and ACTivation) has been employed for such study adapting the code for the beam dump case. For such study a collaboration with the code responsible (Panos Karditsas) at Culham (UKAEA) was established. The work developed in this thesis has supposed the publication of three articles in JCR journals (”Journal of Nuclear Materials��� y ”Fusion Engineering and Design”), as well as presentations in more than four conferences and relevant meetings.

Recent progress in research on tungsten materials for nuclear fusion applications in Europe

The current magnetic confinement nuclear fusion power reactor concepts going beyond ITER are based on assumptions about the availability of materials with extreme mechanical, heat, and neutron load capacity. In Europe, the development of such structural and armour materials together with the necessary production, machining, and fabrication technologies is pursued within the EFDA long-term fusion materials programme. This paper reviews the progress of work within the programme in the area of tungsten and tungsten alloys. Results, conclusions, and future projections are summarized for each of the programme´s main subtopics, which are: (1) fabrication, (2) structural W materials, (3) W armour materials, and (4) materials science and modelling. It gives a detailed overview of the latest results on materials research, fabrication processes, joining options, high heat flux testing, plasticity studies, modelling, and validation experiments.

Analysis of single and binary phases in cerium doped sodium bismuth titanate -Na0.5Bi0.5TiO3 materials

The pure and cerium doped sodium bismuth titanate inorganic powders were synthesized by solid state reaction method. The presence of rhombohedral phase was observed in cerium doped NBT compounds. At 1200 ºC, the 5% of cerium doped NBT compound forms single perovskite phase. The samples of x = 0.10 and 0.15 were heat treated to 1350 ºC, the binary phases with cerium and bismuth oxides were observed. The X-ray diffraction, fourier transform infrared spectroscopy, reflectance spectra, differential thermal analysis and thermo gravimetric analysis were used to analyze the various properties of samples. Moreover, the effects of cerium doping and calcining temperature on NBT samples were investigated. In this work we present our recent results on the synthesis and characterization of Ce doped sodium bismuth titanate materials.

Thermal shields for heat loss reduction in Siemens-type CVD reactors

The use of thermal shields to reduce radiation heat loss in Siemens-type CVD reactors is analyzed, both theoretically and experimentally. The potential savings from the use of the thermal shields is first explored using a radiation heat model that takes emissivity variations with wavelength into account, which is important for materials that do not behave as grey bodies. The theoretical calculations confirm that materials with lower surface emissivity lead to higher radiation savings. Assuming that radiation heat loss is responsible for around 50% of the total power consumption, a reduction of 32.9% and 15.5% is obtained if thermal shields with constant emissivities of 0.3 and 0.7 are considered, respectively. Experiments considering different thermal shields are conducted in a laboratory CVD reactor, confirming that the real materials do not behave as grey bodies, and proving that significant energy savings in the polysilicon deposition process are obtained. Using silicon as a thermal shield leads to energy savings of between 26.5-28.5%. For wavelength-dependent emissivities, the model shows that there are significant differences in radiation heat loss, of around 25%, when compared to that of constant emissivity. The results of the model highlight the importance of having reliable data on the emissivities within the relevant range of wavelengths, and at deposition temperatures, which remains a pending issue.

Aplicación de la celulosa bacteriana a la restauración del patrimonio bibliográfico y documental en papel

La preservación del patrimonio bibliográfico y documental en papel es uno de los mayores retos a los que se enfrentan bibliotecas y archivos de todo el mundo. La búsqueda de soluciones al problema del papel degradado ha sido abordada históricamente desde dos líneas de trabajo predominantes: la conservación de estos documentos mediante la neutralización de los ácidos presentes en ellos con agentes alcalinos, y su restauración mediante el método de laminación fundamentalmente con papel de origen vegetal. Sin embargo, no se ha explorado con éxito la posibilidad de reforzar la celulosa dañada, y el problema sigue sin encontrar una solución satisfactoria. Hasta el día de hoy, el desarrollo de tratamientos basados en biotecnología en la conservación del patrimonio documental ha sido muy escaso, aunque la capacidad de ciertas bacterias de producir celulosa lleva a plantear su uso en el campo de la conservación y restauración del papel. La celulosa bacteriana (CB) es químicamente idéntica a la celulosa vegetal, pero su organización macroscópica es diferente. Sus propiedades únicas (alto grado de cristalinidad, durabilidad, resistencia y biocompatibilidad) han hecho de este material un excelente recurso en diferentes campos. En el desarrollo de esta tesis se ha estudiado el uso de la celulosa bacteriana, de alta calidad, generada por Gluconacetobacter sucrofermentans CECT 7291, para restaurar documentos deteriorados y consolidar los que puedan estar en peligro de degradación, evitando así su destrucción y proporcionando al papel que se restaura unas buenas propiedades mecánicas, ópticas y estructurales. Se desarrollan asimismo protocolos de trabajo que permitan la aplicación de dicha celulosa. En primer lugar se seleccionó el medio de cultivo que proporcionó una celulosa adecuada para su uso en restauración. Para ello se evaluó el efecto que tienen sobre la celulosa generada las fuentes de carbono y nitrógeno del medio de cultivo, manteniendo como parámetros fijos la temperatura y el pH inicial del medio, y efectuando los ensayos en condiciones estáticas. Se evaluó, también, el efecto que tiene en la CB la adición de un 1% de etanol al medio de cultivo. Las capas de celulosa se recolectaron a cuatro tiempos distintos, caracterizando en cada uno de ellos el medio de cultivo (pH y consumo de fuente de carbono), y las capas de CB (pH, peso seco y propiedades ópticas y mecánicas). La mejor combinación de fuentes de carbono y nitrógeno resultó ser fructosa más extracto de levadura y extracto de maíz, con o sin etanol, que proporcionaban una buena relación entre la producción de celulosa y el consumo de fuente de carbono, y que generaban una capa de celulosa resistente y homogénea. La adición de etanol al medio de cultivo, si bien aumentaba la productividad, causaba un descenso apreciable de pH. Las capas de CB obtenidas con los medios de cultivo optimizados se caracterizaron en términos de sus índices de desgarro y estallido, propiedades ópticas, microscopía electrónica de barrido (SEM), difracción de rayos-X, espectroscopía infrarroja con transformada de Fourier (FTIR), grado de polimerización, ángulos de contacto estáticos y dinámicos, y porosimetría de intrusión de mercurio. Por otro lado hay que tener en cuenta que el material restaurado debe ser estable con el tiempo. Por ello esta misma caracterización se efectuó tras someter a las capas de CB a un proceso de envejecimiento acelerado. Los resultados mostraron que la CB resultante tiene un elevado índice de cristalinidad, baja porosidad interna, buenas propiedades mecánicas, y alta estabilidad en el tiempo. Para desarrollar los protocolos de trabajo que permitan la restauración con esta celulosa optimizada, se comienzó con un proceso de selección de los papeles que van a ser restaurados. Se eligieron tres tipos de papeles modelo, hechos con pasta mecánica, química y filtro (antes y después de ser sometidos a un proceso de envejecimiento acelerado), y tres libros viejos adquiridos en el mercado de segunda mano. Estos ejemplares a restaurar se caracterizaron también en términos de sus propiedades mecánicas y fisicoquímicas. El primer protocolo de restauración con CB que se evaluó fue el denominado laminación. Consiste en aplicar un material de refuerzo al documento mediante el uso de un adhesivo. Se seleccionó para ello la CB producida en el medio de cultivo optimizado con un 1% de etanol. Se aplicó un método de purificación alcalino (1 hora a 90 °C en NaOH al 1%) y como adhesivo se seleccionó almidón de trigo. El proceso de laminación se efectuó también con papel japonés (PJ), un material habitualmente utilizado en conservación, para comparar ambos materiales. Se concluyó que no hay diferencias significativas en las características estudiadas entre los dos tipos de materiales de refuerzo. Se caracterizó el material reforzado y, también, después de sufrir un proceso de envejecimiento acelerado. Los papeles laminados con CB mostraban diferencias más marcadas en las propiedades ópticas que los restaurados con PJ, con respecto a los originales. Sin embargo, el texto era más legible cuando el material de restauración era la CB. La mojabilidad disminuía con ambos tipos de refuerzo, aunque en los papeles laminados con CB de manera más marcada e independiente del material a restaurar. Esto se debe a la estructura cerrada de la CB, que también conduce a una disminución en la permeabilidad al aire. Este estudio sugiere que la CB mejora la calidad del papel deteriorado, sin alterar la información que contiene, y que esta mejora se mantiene a lo largo del tiempo. Por tanto, la CB puede ser utilizada como material de refuerzo para laminar, pudiendo ser más adecuada que el PJ para ciertos tipos de papeles. El otro método de restauración que se estudió fue la generación in situ de la CB sobre el papel a restaurar. Para ello se seleccionó el medio de cultivo sin etanol, ya que el descenso de pH que causaba su presencia podría dañar el documento a restaurar. El método de purificación elegido fue un tratamiento térmico (24 horas a 65 °C), menos agresivo para el material a restaurar que el tratamiento alcalino. Se seleccionó la aplicación del medio de cultivo con la bacteria mediante pincel sobre el material a restaurar. Una vez caracterizado el material restaurado, y éste mismo tras sufrir un proceso de envejecimiento acelerado, se concluyó que no hay modificación apreciable en ninguna característica, salvo en la permeabilidad al aire, que disminuye de manera muy evidente con la generación de CB, dando lugar a un material prácticamente impermeable al aire. En general se puede concluir que ha quedado demostrada la capacidad que tiene la celulosa generada por la bacteria Gluconacetobacter sucrofermentans CECT 7291 para ser utilizada como material de refuerzo en la restauración del patrimonio documental en papel. Asimismo se han desarrollado dos métodos de aplicación, uno ex situ y otro in situ, para efectuar esta tarea de restauración. ABSTRACT The preservation of bibliographic and documentary heritage is one of the biggest challenges that libraries and archives around the world have to face. The search for solutions to the problem of degraded paper has historically been focused from two predominants lines of work: the conservation of these documents by the neutralization of acids in them with alkaline agents, and their restoration by lining them with, basically, cellulose from vegetal sources. However, the possibility of strengthening the damaged cellulose has not been successfully explored, and the problem still persists. Until today, the development of biotechnology-based treatments in documentary heritage conservation has been scarce, although the ability of certain bacteria to produce cellulose takes to propose its use in the field of conservation and restoration of paper. The bacterial cellulose (BC) is chemically identical to the plant cellulose, but its macroscopic organization is different. Its unique properties (high degree of crystallinity, durability, strength and biocompatibility), makes it an excellent resource in different fields. The use of high-quality BC generated by Gluconacetobacter sucrofermentans CECT 7291 to restore damaged documents and to consolidate those that may be at risk of degradation, has been studied in this thesis, trying to prevent the document destruction, and to get reinforced papers with good mechanical, optical and structural properties. Protocols that allow the implementation of the BC as a reinforcing material were also developed. First of all, in order to select the culture medium that provides a cellulose suitable for its use in restoration, it has been evaluated the effect that the carbon and nitrogen sources from the culture medium have on the generated BC, keeping the temperature and the initial pH of the medium as fixed parameters, and performing the culture without shaking. The effect of the addition of 1% ethanol to the culture medium on BC properties was also evaluated. The cellulose layers were collected at four different times, characterizing in all of them the culture medium (pH and carbon source consumption), and the BC sheets (pH, dry weight and optical and mechanical properties). The best combination of carbon and nitrogen sources proved to be fructose plus yeast extract and corn steep liquor, with or without ethanol, which provided a good balance between the cellulose production and the consumption of carbon source, and generating BC sheets homogeneous and resistant. The addition of ethanol to the culture medium increased productivity but caused a noticeable decrement in pH. The BC layers generated with these optimized culture media, have been characterized in terms of tear and burst index, optical properties, scanning electron microscopy (SEM), X-ray diffraction, infrared Fourier transform spectroscopy (FTIR), polymerization degree, static and dynamic contact angles, and mercury intrusion porosimetry. Moreover it must be kept in mind that the restored materials should be stable over time. Therefore, the same characterization was performed after subjecting the layers of BC to an accelerated aging process. The results showed that the BC sheets obtained have a high crystallinity index, low internal porosity, good mechanical properties, and high stability over time. To develop working protocols to use this optimized BC in paper restoration, the first step was to select the samples to restore. Three types of model papers, made from mechanical pulp, chemical pulp and filter paper (before and after an accelerated aging process), and three old books purchased in the second hand market, were chosen. These specimens to be restored were also characterized in terms of its mechanical and physicochemical properties. The first protocol of restoration with BC to be evaluated is called linning. It consists on applying a reinforcing material to the document using an adhesive. The BC produced in the optimized culture medium with 1% ethanol was selected. An alkali purification method (1 hour at 90 °C in 1% NaOH) was applied, and wheat starch was selected as adhesive. The linning process was also carried out with Japanese paper (JP), a material commonly used in conservation, in order to compare both materials. It was concluded that there are no significant differences in the characteristics studied of the two types of reinforcing materials. The reinforced materials were characterized before and after undergoing to an accelerated aging. Papers lined with BC showed more marked differences in the optical properties that papers restored with JP. However, the text was more readable when BC was the reinforcing material. Wettability decreased with both types of reinforcement, although in the papers linned with BC it happened more marked and independently of the sample to restore. This is due to the closed structure of BC, which also leads to a decrement in air permeance. This study suggests that BC improves the deteriorated paper quality, without altering the information on it, and that this improvement is maintained over time. Therefore, the BC may be used as reinforcing material for linning, being more suitable than the JP to restore certain types of papers. The other restoration method to be evaluated was the in situ generation of BC over the paper to restore. For this purpose the culture medium without ethanol was selected, as the pH decrement caused by his presence would damage the document to restore. As purification method a heat treatment (24 hours at 65 °C) was chosen, less aggressive to the material to restore than the alkaline treatment. It was decided to apply the culture medium with the bacteria onto the material to restore with a brush. The reinforced material was characterized before and after an accelerated aging process. It was concluded that there was no substantial change in any characteristic, except for air permeance, which decreases very sharply after the generation of BC, getting a substantially air impermeable material. In general, it can be concluded that the ability of BC produced by Gluconacetobacter sucrofermentans CECT 7291 for its use as a reinforcing material in the restoration of paper documentary heritage, has been demonstrated. Also, two restoration methods, one ex situ and another in situ have been developed.

Ultra high temperature latent heat energy storage and thermophotovoltaic energy conversion

A conceptual energy storage system design that utilizes ultra high temperature phase change materials is presented. In this system, the energy is stored in the form of latent heat and converted to electricity upon demand by TPV (thermophotovoltaic) cells. Silicon is considered in this study as PCM (phase change material) due to its extremely high latent heat (1800 J/g or 500 Wh/kg), melting point (1410 C), thermal conductivity (~25 W/mK), low cost (less than $2/kg or $4/kWh) and abundance on earth. The proposed system enables an enormous thermal energy storage density of ~1 MWh/m3, which is 10e20 times higher than that of lead-acid batteries, 2e6 times than that of Li-ion batteries and 5e10 times than that of the current state of the art LHTES systems utilized in CSP (concentrated solar power) applications. The discharge efficiency of the system is ultimately determined by the TPV converter, which theoretically can exceed 50%. However, realistic discharge efficiencies utilizing single junction TPV cells are in the range of 20e45%, depending on the semiconductor bandgap and quality, and the photon recycling efficiency. This concept has the potential to achieve output electric energy densities in the range of 200-450 kWhe/m3, which is comparable to the best performing state of the art Lithium-ion batteries.