Unimanual and Bimanual Weight Perception of Virtual Objects with a new Multi-finger Haptic Interface

Accurate weight perception is important particularly in tasks where the user has to apply vertical forces to ensure safe landing of a fragile object or precise penetration of a surface with a probe. Moreover, depending on physical properties of objects such as weight and size we may switch between unimanual and bimanual manipulation during a task. Research has shown that bimanual manipulation of real objects results in a misperception of their weight: they tend to feel lighter than similarly heavy objects which are handled with one hand only [8]. Effective simulation of bimanual manipulation with desktop haptic interfaces should be able to replicate this effect of bimanual manipulation on weight perception. Here, we present the MasterFinger-2, a new multi-finger haptic interface allowing bimanual manipulation of virtual objects with precision grip and we conduct weight discrimination experiments to evaluate its capacity to simulate unimanual and bimanual weight. We found that the bimanual ‘lighter’ bias is also observed with the MasterFinger-2 but the sensitivity to changes of virtual weights deteriorated.

Visual Servoing for the Robotenis System: a Strategy for a 3 DOF Parallel Robot to Hit a Ping-Pong Ball

This article describes a new visual servo control and strategies that are used to carry out dynamic tasks by the Robotenis platform. This platform is basically a parallel robot that is equipped with an acquisition and processing system of visual information, its main feature is that it has a completely open architecture control, and planned in order to design, implement, test and compare control strategies and algorithms (visual and actuated joint controllers). Following sections describe a new visual control strategy specially designed to track and intercept objects in 3D space. The results are compared with a controller shown in previous woks, where the end effector of the robot keeps a constant distance from the tracked object. In this work, the controller is specially designed in order to allow changes in the tracking reference. Changes in the tracking reference can be used to grip an object that is under movement, or as in this case, hitting a hanging Ping-Pong ball. Lyapunov stability is taken into account in the controller design.

Evolution and treatment of vitamin B12 deficiency as a risk factor for (cognitive and functional) neurodegenerative diseases in institutionalized elderly = Evolución y tratamiento de la deficiencia de vitamina B12 como factor de riesgo de enfermedades neurodegenerativas (cognitivas y funcionales) en las personas mayores institucionalizadas.

Prevalence of vitamin B12 deficiency is very common in elderly people and can reach values as high as 40.5% of the population. It can be the result of the interaction among several factors. Vitamin B12 deficiencies have been associated with neurological, cognitive deterioration, haematological abnormalities and cardiovascular diseases that have an important influence on the health of the elderly and their quality of life. It is necessary to approach the problems arisen from the lack of data relative to them. The main objective of this thesis was to analyse the evolution of vitamin B12 status and related parameters, lipid and haematological profiles and their relationship to health risk factors, and to functional and cognitive status over one year and to determine the effect of an oral supplementation of 500 μg of cyanocobalamin for a short period of 28 days. An additional objective was to analyze the possible effects of medicine intakes on vitamin B status. Three studies were performed: a) a one year longitudinal follow-up with four measure points; b) an intervention study providing an oral liquid supplement of 500 μg of cyanocobalamin for a 28 days period; and c) analysis of the possible effect of medication intake on vitamin B status using the ATC classification of medicines. The participants for these studies were recruited from nursing homes for the elderly in the Region of Madrid. Sixty elders (mean age 84 _ 7y, 19 men and 41 women) were recruited for Study I and 64 elders (mean age 82 _ 7y, 24 men and 40 women) for Study II. For Study III, baseline data from the initially recruited participants of the first two studies were used. An informed consent was obtained from all participants or their mentors. The studies were approved by the Ethical Committee of the University of Granada. Blood samples were obtained at each examination date and were analyzed for serum cobalamin, holoTC, serum and RBC folate and total homocysteine according to laboratory standard procedures. The haematological parameters analyzed were haematocrit, haemoglobin and MCV. For the lipid profile TG, total cholesterol, LDL- and HDLcholesterol were analyzed. Anthropometric measures (BMI, skinfolds [triceps and subscapular], waist girth and waist to hip ratio), functional tests (hand grip, arm and leg strength tests, static balance) and MMSE were obtained or administered by trained personal. The vitamin B12 supplement of Study II was administered with breakfast and the medication intake was taken from the residents’ anamnesis. Data were analyzed by parametric and non-parametric statistics depending on the obtained data. Comparisons were done using the appropriate ANOVAs or non-parametric tests. Pearsons’ partial correlations with the variable “time” as control were used to define the association of the analyzed parameters. XIII The results showed that: A) Over one year, in relationship to vitamin B status, serum cobalamin decreased, serum folate and mean corpuscular volumen increased significantly and total homocysteine concentrations were stable. Regarding blood lipid profile, triglycerides increased and HDL-cholesterol decreased significantly. Regarding selected anthropometric measurements, waist circumference increased significantly. No significant changes were observed for the rest of parameters. B) Prevalence of hyperhomocysteinemia was high in the elderly studied, ranging from 60% to 90 % over the year depending on the cut-off used for the classification. LDL-cholesterol values were high, especially among women, and showed a tendency to increase over the year. Results of the balance test showed a deficiency and a tendency to decrease; this indicates that the population studied is at high risk for falls. Lower extremity muscular function was deficient and showed a tendency to decrease. A highly significant relationship was observed between the skinfold of the triceps and blood lipid profile. C) Low cobalamin concentrations correlated significantly with low MMSE scores in the elderly studied. No correlations were observed between vitamin B12 status and functional parameters. D) Regarding vitamin B12 status, holo-transcobalamin seems to be more sensitive for diagnosis; 5-10% of the elderly had a deficiency using serum cobalamin as a criterion, and 45-52% had a deficiency when using serum holotranscobalamin as a criterion. E) 500 μg of cyanocobalamin administered orally during 28 days significantly improved vitamin B12 status and significantly decreased total homocysteine concentrations in institutionalized elderly. No effect of the intervention was observed on functional and cognitive parameters. F) The relative change (%) of improvement of vitamin B12 status was higher when using serum holo-transcobalamin as a criterion than serum cobalamin. G) Antiaenemic drug intake normalized cobalamin, urologic drugs and corticosteroids serum folate, and psychoanaleptics holo-transcobalamin levels. Drugs treating pulmonary obstruction increased total homocysteine concentration significantly. H) The daily mean drug intake was 5.1. Fiftynine percent of the elderly took medication belonging to 5 or more different ATC groups. The most prevalent were psycholeptic (53%), antiacid (53%) and antithrombotic (47%) drugs.

Influencia de las condiciones de ejecución en la resistencia de anclajes en convencional y autocompactante

A través de los años las estructuras de hormigón armado han ido aumentando su cuota de mercado, sustituyendo a las estructuras de fábrica de piedra o ladrillo y restándole participación a las estructuras metálicas. Uno de los primeros problemas que surgieron al ejecutar las estructuras de hormigón armado, era cómo conectar una fase de una estructura de este tipo a una fase posterior o a una modificación posterior. Hasta los años 80-90 las conexiones de una fase de una estructura de hormigón armado, con otra posterior se hacían dejando en la primera fase placas de acero con garrotas embebidas en el hormigón fresco o barras grifadas recubiertas de poliestireno expandido. Una vez endurecido el hormigón se podían conectar nuevas barras, para la siguiente fase mediante soldadura a la placa de la superficie o enderezando las barras grifadas, para embeberlas en el hormigón fresco de la fase siguiente. Estos sistemas requerían conocer la existencia y alcance de la fase posterior antes de hormigonar la fase previa. Además requerían un replanteo muy exacto y complejo de los elementos de conexión. Otro problema existente en las estructuras de hormigón era la adherencia de un hormigón fresco a un hormigón endurecido previamente, ya que la superficie de contacto de ambos hormigones suponía un punto débil, con una adherencia baja. A partir de los años 80, la industria química de la construcción experimentó un gran avance en el desarrollo de productos capaces de generar una buena adherencia sobre el hormigón endurecido. Este avance tecnológico tenía aplicación tanto en la adherencia del hormigón fresco sobre el hormigón endurecido, como en la adherencia de barras post-instaladas en agujeros de hormigón endurecido. Este sistema se denominó “anclajes adherentes de barras de acero en hormigón endurecido”. La forma genérica de ejecutarlos es hacer una perforación cilíndrica en el soporte de hormigón, con una herramienta especifica como un taladro, limpiar la perforación, llenarla del material adherente y finalmente introducir la barra de acero. Los anclajes adherentes se dividen en anclajes cementosos y anclajes químicos, siendo estos últimos los más habituales, fiables, resistentes y fáciles de ejecutar. El uso del anclaje adherente de barras de acero en hormigón endurecido se ha extendido por todo el espectro productivo, siendo muy habitual tanto en construcción de obras de hormigón armado de obra civil y edificación, como en obras industriales, instalaciones o fijación de elementos. La ejecución de un anclaje de una barra de acero en hormigón endurecido depende de numerosas variables, que en su conjunto, o de forma aislada pueden afectar de forma notable a la resistencia del anclaje. Nos referimos a variables de los anclajes, que a menudo no se consideran tales como la dirección de la perforación, la máquina de perforación y el útil de perforación utilizado, la diferencia de diámetros entre el diámetro del taladro y la barra, el tipo de material de anclaje, la limpieza del taladro, la humedad del soporte, la altura del taladro, etc. La utilización en los últimos años de los hormigones Autocompactables, añade una variable adicional, que hasta ahora apenas ha sido estudiada. En línea con lo apuntado, la presente tesis doctoral tiene como objetivo principal el estudio de las condiciones de ejecución en la resistencia de los anclajes en hormigón convencional y autocompactable. Esta investigación se centra principalmente en la evaluación de la influencia de una serie de variables sobre la resistencia de los anclajes, tanto en hormigón convencional como en un hormigón autocompactable. Para este estudio ha sido necesaria la fabricación de dos soportes de hormigón sobre los cuales desarrollar los ensayos. Uno de los bloques se ha fabricado con hormigón convencional y el otro con hormigón autocompactable. En cada pieza de hormigón se han realizado 174 anclajes con barras de acero, variando los parámetros a estudiar, para obtener resultados de todas las variables consideradas. Los ensayos a realizar en ambos bloques son exactamente iguales, para poder comparar la diferencia entre un anclaje en un soporte de hormigón con vibrado convencional (HVC) y un hormigón autocompactante (HAC). De cada tipo de ensayo deseado se harán dos repeticiones en la misma pieza. El ensayo de arrancamiento de las barras se realizara con un gato hidráulico hueco, con un sistema de instrumentación de lectura y registro de datos en tiempo real. El análisis de los resultados, realizado con una potente herramienta estadística, ha permitido determinar y evaluar numéricamente la influencia de los variables consideradas en la resistencia de los anclajes realizados. Así mismo ha permitido diferenciar los resultados obtenidos en los hormigones convencionales y autocompactantes, tanto desde el punto de vista de la resistencia mecánica, como de las deformaciones sufridas en el arrancamiento. Se define la resistencia mecánica de un anclaje, como la fuerza desarrollada en la dirección de la barra, para hacer su arrancamiento del soporte. De la misma forma se considera desplazamiento, a la separación entre un punto fijo de la barra y otro del soporte, en la dirección de la barra. Dichos puntos se determinan cuando se ha terminado el anclaje, en la intersección de la superficie plana del soporte, con la barra. Las conclusiones obtenidas han permitido establecer qué variables afectan a la ejecución de los anclajes y en qué cuantía lo hacen, así como determinar la diferencia entre los anclajes en hormigón vibrado convencional y hormigón autocompactante, con resultados muy interesantes, que permiten valorar la influencia de dichas variables. Dentro de las conclusiones podemos destacar tres grupos, que denominaremos como de alta influencia, baja influencia y sin influencia. En todos los casos hay que hacer el estudio en términos de carga y de desplazamiento. Podemos considerar como de alta influencia, en términos de carga las variables de máquina de perforación y el material de anclaje. En términos de desplazamiento podemos considerar de alta influencia además de la máquina de perforación y el material de anclaje, el diámetro del taladro, así como la limpieza y humedad del soporte. Podemos considerar de baja influencia, en términos de carga las variables de tipo de hormigón, dirección de perforación, limpieza y humedad del soporte. En términos de desplazamiento podemos considerar de baja influencia el tipo de hormigón y la dirección de perforación. Podemos considerar en el apartado de “sin influencia”, en términos de carga las variables de diámetro de perforación y altura del taladro. En términos de desplazamiento podemos considerar como “sin influencia” la variable de altura del taladro. Podemos afirmar que las diferencias entre los valores de carga aumentan de forma muy importante en términos de desplazamiento. ABSTRACT Over the years the concrete structures have been increasing their market share, replacing the masonry structures of stone or brick and subtracting as well the participation of the metallic structures. One of the first problems encountered in the implementing of the reinforced concrete structures was connecting a phase structure of this type at a later stage or a subsequent amendment. Until the 80s and 90s the connections of one phase of a reinforced concrete structure with a subsequent first phase were done by leaving the steel plates embedded in the fresh concrete using hooks or bent bars coated with expanded polystyrene. Once the concrete had hardened new bars could be connected to the next stage by welding them to the surface plate or by straightening the bent bars to embed them in the fresh concrete of the next phase. These systems required a previous knowledge of the existence and scope of the subsequent phase before concreting the previous one. They also required a very precise and complex rethinking of the connecting elements. Another existing problem in the concrete structures was the adhesion of a fresh concrete to a previously hardened concrete, since the contact surface of both concretes leaded to a weak point with low adherence. Since the 80s, the chemicals construction industry experienced a breakthrough in the development of products that generate a good grip on the concrete. This technological advance had its application both in the grip on one hardened fresh concrete and in the adhesion of bar post-installed in holes of hardened concrete. This system was termed as adherent anchors of steel bars in hardened concrete. The generic way of executing this system is by firstly drilling a cylindrical hole in the concrete support using a specific tool such as a drill. Then, cleaning the bore and filling it with bonding material to lastly, introduce the steel bar. These adherent anchors are divided into cement and chemical anchors, the latter being the most common, reliable, durable and easy to run. The use of adhesive anchor of steel bars in hardened concrete has spread across the production spectrum turning itself into a very common solution in both construction of reinforced concrete civil engineering and construction, and industrial works, installations and fixing elements as well. The execution of an anchor of a steel bar in hardened concrete depends on numerous variables which together or as a single solution may significantly affect the strength of the anchor. We are referring to variables of anchors which are often not considered, such as the diameter difference between the rod and the bore, the drilling system, cleansing of the drill, type of anchor material, the moisture of the substrate, the direction of the drill, the drill’s height, etc. During recent years, the emergence of self-compacting concrete adds an additional variable which has hardly been studied so far. According to mentioned this thesis aims to study the main performance conditions in the resistance of conventional and self-compacting concrete anchors. This research is primarily focused on the evaluation of the influence of several variables on the strength of the anchoring, both in conventional concrete and self-compacting concrete. In order to complete this study it has been required the manufacture of two concrete supports on which to develop the tests. One of the blocks has been manufactured with conventional concrete and the other with self-compacting concrete. A total of 174 steel bar anchors have been made in each one of the concrete pieces varying the studied parameters in order to obtain results for all variables considered. The tests to be performed on both blocks are exactly the same in order to compare the difference between an anchor on a stand with vibrated concrete (HVC) and a self-compacting concrete (SCC). Each type of test required two repetitions in the same piece. The pulling test of the bars was made with a hollow jack and with an instrumentation system for reading and recording data in real time. The use of a powerful statistical tool in the analysis of the results allowed to numerically determine and evaluate the influence of the variables considered in the resistance of the anchors made. It has likewise enabled to differentiate the results obtained in the self-compacting and conventional concretes, from both the outlook of the mechanical strength and the deformations undergone by uprooting. The mechanical strength of an anchor is defined as the strength undergone in a direction of the bar to uproot it from the support. Likewise, the movement is defined as the separation between a fixed point of the bar and a fixed point from the support considering the direction of the bar. These points are only determined once the anchor is finished, with the bar, at the intersection in the flat surface of the support. The conclusions obtained have established which variables affect the execution of the anchors and in what quantity. They have also permitted to determine the difference between the anchors in vibrated concrete and selfcompacting concrete with very interesting results that also allow to assess the influence of these mentioned variables. Three groups are highlighted among the conclusions called high influence, low influence and no influence. In every case is necessary to perform the study in terms of loading and movement. In terms of loading, there are considered as high influence two variables: drilling machinery and anchorage material. In terms of movement, there are considered as high influence the drilling diameter and the cleaning and moisture of the support, besides the drilling machinery and the anchorage material. Variables such as type of concrete, drilling direction and cleaning and moisture of the support are considered of low influence in terms of load. In terms of movement, the type of concrete and the direction of the drilling are considered variables of low influence. Within the no influence section in terms of loading, there are included the diameter of the drilling and the height of the drill. In terms of loading, the height of the drill is considered as a no influence variable. We can affirm that the differences among the loading values increase significantly in terms of movement.

A data-globe and immersive virtual reality environment for upper limb rehabilitation after spinal cord injury

While a number of virtual data-gloves have been used in stroke, there is little evidence about their use in spinal cord injury (SCI). A pilot clinical experience with nine SCI subjects was performed comparing two groups: one carried out a virtual rehabilitation training based on the use of a data glove, CyberTouch combined with traditional rehabilitation, during 30 minutes a day twice a week along two weeks; while the other made only conventional rehabilitation. Furthermore, two functional indexes were developed in order to assess the patient’s performance of the sessions: normalized trajectory lengths and repeatability. While differences between groups were not statistically significant, the data-glove group seemed to obtain better results in the muscle balance and functional parameters, and in the dexterity, coordination and fine grip tests. Related to the indexes that we implemented, normalized trajectory lengths and repeatability, every patient showed an improvement in at least one of the indexes, either along Y-axis trajectory or Z-axis trajectory. This study might be a step in investigating new ways of treatments and objective measures in order to obtain more accurate data about the patient’s evolution, allowing the clinicians to develop rehabilitation treatments, adapted to the abilities and needs of the patients.

Perfil antropométrico y respuesta psico-fisiológica en escalada deportiva en roca: Diferencias entre modalidades

En la literatura se ha descrito el perfil antropométrico y la respuesta psicofisiológica en escalada deportiva en roca, pero hasta la fecha, no se habían analizado las diferencias existentes entre sus principales modalidades. El objetivo de la presente tesis fue describir las características antropométricas del escalador de competición y comprobar la existencia de diferencias entre los participantes de distintas modalidades, así como analizar la respuesta psico-fisiológica durante la ejecución de un búlder y una vía, además de evaluar las diferencias entre su realización a vista o tras un ensayo. Para ello, efectuamos dos estudios diferentes: en el primero participaron voluntariamente 61 hombres y 18 mujeres, participantes en cuatro pruebas del circuito nacional de competición de escalada durante el año 2009, tres de ellas de la modalidad de dificultad a vista y una de búlder. Se realizaron mediciones antropométricas, prueba de fuerza de prensión manual antes y después de competir, y se cumplimentó un cuestionario donde se evaluaba la percepción del esfuerzo y la experiencia deportiva. En el segundo estudio, 23 escaladores, 15 hombres y 8 mujeres, divididos en tres grupos en función de su nivel de rendimiento, realizaron de manera voluntaria distintas pruebas durante tres días separados entre sí al menos 48 horas. El primer día rellenaron un cuestionario sobre su experiencia deportiva y nivel de rendimiento, fueron pesados, tallados y sometidos a un escáner de cuerpo completo en densitómetro con objeto de medir la composición corporal. El segundo día realizaron previo calentamiento, un búlder a vista y, tras un descanso de 15 minutos, escalaron una vía a vista acorde con su nivel. El tercer día, después de calentar y disponer de 20 minutos para ensayarlo, repitieron la escalada del búlder. Tras un descanso de 15 minutos y 20 minutos de ensayo, realizaron un segundo intento a la vía. Se registraron los valores en la respuesta cardiorrespiratoria, se obtuvieron muestras de lactato en sangre del lóbulo de la oreja y se realizaron pruebas de fuerza de prensión manual antes y después de la escalada. También se pasó un cuestionario para medir la ansiedad y autoconfianza así como el esfuerzo percibido. Los resultados no mostraron diferencias antropométricas significativas entre los participantes en competiciones de búlder y los que participaron en competiciones de escalada de dificultad a vista. Se dieron diferencias en la pérdida de fuerza antes y después de escalar entre dichos participantes. Las mujeres obtuvieron menor fuerza de prensión manual que los hombres pero la misma pérdida de fuerza entre el instante antes de competir y el posterior. La respuesta fisiológica durante la ejecución del búlder fue menor que la obtenida durante la ejecución de la vía. Hubo pérdida de fuerza de prensión manual entre el instante anterior y el posterior a ejecutar la vía, pero no al hacer el búlder. Sin embargo, no se dieron diferencias en la ansiedad y la autoestima provocada por ambas modalidades, por lo que deducimos que la ejecución de un búlder y una vía presentan una respuesta fisiológica distinta. Proponemos que la respuesta está relacionada, sobre todo, con las variables de ejecución, de tal manera que a mayor distancia y/o tiempo recorrido en la escalada, mayor será la contribución anaeróbica al esfuerzo y la fatiga manifestada como pérdida de fuerza que, en el caso del búlder, fue mínima o inexistente. En el segundo intento, tras un ensayo de 20 minutos en el búlder, se consiguió mejorar el rendimiento respecto al primer intento, que se manifestó con un aumento en la distancia recorrida. Sin embargo, en la vía no se dieron diferencias entre ambos intentos, ni en la ejecución, ni en la respuesta fisiológica, ni en la ansiedad, ni siquiera en la fuerza de prensión manual. ABSTRACT It has been described in the literature the anthropometric profile and psychophysiological response in rock climbing, but so far not been analyzed differences between its main modalities. The aim of this thesis was to describe the anthropometric characteristics of the climber competitor and check for differences between participants of different modalities and to analyze the psycho-physiological response during the execution of a boulder and a route also to assess differences between on sight and redpoint attempts. We made two different studies: in the first 61 men and 18 women who attended four competitions of national climbing circuit in 2009, three of them on-sight difficulty competitions and a boulder competition participated voluntarily. Anthropometric measurements, a hand grip strength test before and after competing were registered for each climber, and a questionnaire which assessed perception of effort and the climbing experience was fulfilled. In the second study, various tests were conducted on 23 volunteer climbers, 15 men and 8 women, during three days separated for, at least, 48 hours of resting, divided into three groups according to their performance. The first day, climbers completed a questionnaire on their experience and performance level. It was recorded weight, height and they underwent a full body scan densitometer in order to measure body composition. The second day, after previous warming-up, they climbed a boulder on sight and, after a break of 15 minutes, climbed a route on-sight according to their level. The third day, after warming-up and have 20 minutes to try it, they repeated the bouldering climbing. After a break of 15 minutes and 20 minutes of essaying, they made a second attempt at the route. Values in the cardiorespiratory response were recorded, blood lactate samples were obtained from earlobe, and hand grip strength was tested before and after the climb. They also filled a questionnaire to measure anxiety and self-confidence and perceived exertion. The results showed no significant anthropometric differences between participants in bouldering competitions and participants in competitions on-sight difficulty climbing. There were found differences in strength loss before and after climbing between those participants. Women had less hand grip strength than men but the same loss of strength between the records carried out before and after competing. The physiological response recorded for boulder climbing was lower than the obtained for the route. There was loss of hand grip strength between the time before and after running the route but not for bouldering. However, there were no differences in anxiety and self-esteem caused by both modalities, so we conclude that the implementation of a boulder and a route have different physiological responses. We think that this response is mainly related to performance variables, as a greater distance and/or travel time on the climb, the higher the anaerobic contribution to the effort and fatigue as manifested by loss of strength in the case of the boulder was minimal or nonexistent. In the second attempt after 20 minutes in the boulder better performance was achieved on the first attempt, which was manifested by an increment of climbing distance. However, there were the differences in the route between the two attempts, either in execution or in the physiological response, or anxiety, or even in hand grip strength.