Air-steam gasification of sewage sludge in a bubbling bed reactor: Effect of alumina as a primary catalyst

Numerous references can be found in scientific literature regarding biomass gasification. However, there are few works related to sludge gasification. A study of sewage sludge gasification process in a bubbling fluidised bed gasifier on a laboratory scale is here reported. The aim was to find the optimum conditions for reducing the production of tars and gain more information on the influx of different operating variables in the products resulting from the gasification of this waste. The variables studied were the equivalence ratio (ER), the steam-biomass ratio (SB) and temperature. Specifically, the ER was varied from 0.2 to 0.4, the SB from 0 to 1 and the temperature from 750 °C (1023 K) to 850 °C (1123 K). Although it was observed that tar production could be considerably reduced (up to 72%) by optimising the gasification conditions, the effect of using alumina (aluminium oxide, of proven efficacy in destroying the tar produced in biomass gasification) as primary catalyst in air and air-steam mixture tests was also verified. The results show that by adding small quantities of alumina to the bed (10% by weight of fed sludge) considerable reductions in tar production can be obtained (up to 42%) improving, at the same time, the lower heating value (LHV) of the gas and carbon conversion.

Sewage sludge gasification. Dolomite performance under different operating conditions

Gasification is a technology that can replace traditional management alternatives used up to date to deal with this waste (landfilling, composting and incineration) and which fulfils the social, environmental and legislative requirements. The main products of sewage sludge gasification are permanent gases (useful to generate energy or to be used as raw material in chemical synthesis processes), liquids (tars) and char. One of the main problems to be solved in gasification is tar production. Tars are organic impurities which can condense at relatively high temperatures making impossible to use the produced gases for most applications. This work deals with the effect of some primary tar removal processes (performed inside the gasifier) on sewage sludge gasification products. For this purpose, analysis of the gas composition, tar production, cold gas efficiency and carbon conversion were carried out. The tests were performed with air in a laboratory scale plant consisting mainly of a bubbling bed gasifier. No catalyzed and catalyzed (10% wt of dolomite in the bed and in the feeding) tests were carried out at different temperatures (750ºC, 800ºC and 850ºC) in order to know the effect of these parameters in the gasification products. As far as tars were concerned, qualitative and quantitative tar composition was determined. In all tests the Equivalence Ratio (ER) was kept at 0.3. Temperature is one of the most influential variables in sewage sludge gasification. Higher temperatures favoured hydrogen and CO production while CO2 content decreased, which might be partially explained by the effect of the cracking, Boudouard and CO2 reforming reactions. At 850ºC, cold gas efficiency and carbon conversion reached 49% and 76%, respectively. The presence of dolomite as catalyst increased the production of H2 reaching contents of 15.5% by volume at 850 °C. Similar behaviour was found for CO whereas CO2 and CnHm (light hydrocarbons) production decreased. In the presence of dolomite, a tar reduction of up to 51% was reached in comparison with no catalyzed tests, as well as improvements on cold gas efficiency and carbon conversion. Several assays were developed in order to test catalyst performance under more rough gasification conditions. For this purpose, the throughput value (TR), defined as kg sludge “as received” fed to the gasifier per hour and per m2 of cross sectional area of the gasifier, was modified. Specifically, the TR values used were 110 (reference value), 215 and 322 kg/h·m2. When TR increased, the H2, CO and CH4 production decreased while the CO2 and the CnHm production increased. Tar production increased drastically with TR during no catalysed tests what is related to the lower residence time of the gas inside the reactor. Nevertheless, even at TR=322 kg/h·m2, tar production decreased by nearly 50% with in-bed use of dolomite in comparison with no catalyzed assays under the same operating conditions. Regarding relative tar composition, there was an increase in benzene and naphthalene content when temperature increased while the content of the rest of compounds decreased. The dolomite seemed to be effective all over the range of molecular weight studied showing tar removal efficiencies between 35-55% in most cases. High values of the TR caused a significant increase in tar production but a slight effect on tar composition.

Incorporación de escorias de aluminio en la fabricación de productos de Arcilla cocida

Las sociedades desarrolladas generan una gran cantidad de residuos, que necesitan una adecuada gestión. Esta problemática requiere, de este modo, una atención creciente por parte de la sociedad, debido a la necesidad de proteger el medio ambiente. En este sentido, los esfuerzos se centran en reducir al máximo la generación de residuos y buscar vías de aprovechamiento de aquellos que son inevitables, soluciones mucho más aconsejables desde el punto de vista técnico, ecológico y económico que su vertido o destrucción. Las industrias deben adoptar las medidas precisas para fomentar la reducción de estos residuos, desarrollar tecnologías limpias que permitan el ahorro de los recursos naturales que poseemos, y sobre todo buscar métodos de reutilización, reciclado, inertización y valorización de los residuos generados en su producción. La industria de la construcción es un campo muy receptivo para el desarrollo de nuevos materiales en los que incorporar estos residuos. La incorporación de diferentes residuos industriales en matrices cerámicas se plantea como una vía barata de fijar las diferentes especies metálicas presentes en transformación de rocas ornamentales, lodos de galvanización o metalúrgicos, etc. En todos los casos, la adición de estos residuos requiere su caracterización previa y la optimización de las condiciones de conformado y cocción en el caso de su incorporación a la arcilla cocida. Entre los residuos incorporados en materiales de construcción se encuentran las escorias de aluminio. La industria metalúrgica produce durante sus procesos de fusión diferentes tipos de escorias. Su reciclado es una de las líneas de interés para estas industrias. En el caso de las escorias de aluminio, su tratamiento inicial consiste en una recuperación del aluminio mediante métodos mecánicos seguido de un tratamiento químico, o plasma. Este método conduce a que la escoria final apenas contenga aluminio y sea rica en sales solubles lo que limita su almacenamiento en escombreras. La escoria es una mezcla de aluminio metal y productos no metálicos como óxidos, nitruros y carburos de aluminio, sales y otros óxidos metálicos. En este estudio se ha analizado la posibilidad de la adición de escorias de aluminio procedentes de la metalurgia secundaria en materiales de construcción, de forma que tras un procesado de las mismas permita la obtención de materiales compuestos de matriz cerámica. En la presente Tesis Doctoral se ha analizado la viabilidad técnica de la incorporación de las escorias de aluminio procedentes de la metalurgia secundaria en una matriz de arcilla cocida. Para ello se han aplicado diferentes tratamientos a la escoria y se han aplicado diferentes variables en su procesado como la energía de molienda o la temperatura de sinterizacion, además del contenido de escoria. Su compactación con agua entre el 5-10 %, secado y sinterización permite obtener piezas rectangulares de diverso tamaño. Desde el punto de vista del contenido de la escoria, se incorporó entre un 10 y 40% de escoria TT, es decir sometida una calcinación previa a 750ºC en aire. Los mejores resultados alcanzados corresponden a un contenido del 20% ESC TT, sinterizada a 980ºC, por cuanto altos contenidos en escoria condicen a piezas con corazón negro. Los productos obtenidos con la adición de 20% de escoria de aluminio a la arcilla, presentan una baja expansión tras sinterización, mejores propiedades físicas y mecánicas, y mayor conductividad térmica que los productos obtenidos con arcilla sin adiciones. Aumenta su densidad, disminuye su absorción y aumenta sus resistencias de flexión y compresión, al presentar una porosidad cerrada y una interacción escoria-matriz. En todos los casos se produce una exudación superficial de aluminio metálico, cuyo volumen está relacionado con la cantidad de escoria adicionada. Mediante la incorporación de este contenido de escoria, tras un tratamiento de disolución de sales y posterior calcinación (ESC TTQ), se mejoran las propiedades del material compuesto, no sólo sobre la de la escoria calcinada (ESC TT), sino también, sobre la escoria sin tratamiento (ESC). Si además, la adición del 20% de escoria añadida, está tratada, no sólo térmicamente sino también químicamente (ESC TTQ), éstas mejoran aún más las propiedades del material compuesto, siendo el producto más compacto, con menos poros, por lo que los valores de densidad son más elevados, menores son las absorciones y mayores resistencias de flexión y compresión, que los productos obtenidos con la adición de escoria sólo tratada térmicamente. Alcanzando valores de resistencias características a compresión del orden de 109 MPa. Los valores de conductividad térmica obtenidos también son mayores. Los ensayos tecnológicos con piezas de 160 x 30 x 5 mm y el material compuesto optimizado de arcilla+ 20%ESCTTQ, consistieron en la determinación de su expansión por humedad, eflorescencia y heladicidad, mostrando en general un mejor comportamiento que la arcilla sin adiciones. Así, se han obtenido nuevos materiales compuestos de matriz cerámica para la construcción, mejorando sus propiedades físicas, mecánicas y térmicas, utilizando escorias de aluminio procedentes de la metalurgia secundaria, como opción de valorización de estos residuos, evitando así, que se viertan a vertederos y contaminen el medio ambiente. ABSTRACT Developed societies generate a lot of waste, which need proper management. Thus, this problem requires increased attention from the society, due to the need to protect the environment. In this regard, efforts are focused on to minimize the generation of waste and find ways of taking advantage of those who are inevitable, much more advisable solutions from the technical, ecological and economic viewpoint to disposal or destruction. Industries should adopt precise measures to promote waste reduction, develop clean technologies that allow the saving of natural resources that we possess, and above all seek methods of reuse, recycling, recovery and valorisation of the waste generated in their production. The industry of the construction is a very receptive field for the development of new materials in which to incorporate these residues. The incorporation of different industrial residues in ceramic counterfoils appears as a cheap route to fix the different metallic present species in transformation of ornamental rocks, muds of galvanization or metallurgical, etc. In all the cases, the addition of these residues needs his previous characterization and the optimization of the conditions of conformed and of baking in case of his incorporation to the baked clay. Residues incorporated into construction materials include aluminium slag. The metallurgical industry produces during their fusion processes different types of slags. Recycling is one of the lines of interest to these industries. In the case of aluminium slag, their initial treatment consists of a recovery of the aluminium using mechanical methods followed by chemical treatment, or plasma. This method leads to that final slag just contains aluminium and is rich in soluble salts which limits storage in dumps. The slag is a mixture of aluminium metal and non-metallic such as oxides, nitrides and carbides of aluminium salts products and other metal oxides. The present Doctoral thesis has analysed the technical viability of the incorporation of aluminium slag from secondary Metallurgy in an array of baked clay. So they have been applied different treatments to the slag and have been applied different variables in its processing as the temperature of sintering, in addition to the content of slag or energy grinding. Its compaction with water between 5-10%, drying and sintering allows rectangular pieces of different size. From the point of view of the content of the slag, it is incorporated between 10 and 40% slag TT, that is to say, submitted a calcination prior to 750 ° C in air. The best results achieved correspond to 20% ESC TT, sintered at 980 ° C, as high levels of slag in accordance to pieces with black heart. The products obtained with the addition of 20% of slag from aluminium to clay, present a low expansion after sintering, better physical properties and mechanical, and higher thermal conductivity than the products obtained with clay, without addictions. Its density increases, decreases its absorption and increases its resistance to bending and compression, introducing a closed porosity and slag-matrix interaction. In all cases there is a superficial exudation of metallic aluminium, whose volume is related to the amount of slag added. By incorporating this content of slag, following a treatment of salt solution and subsequent calcination (ESC TTQ), are improved the properties of composite material not only on the calcined slag (ESC TT), but also in the slag without treatment (ESC). If the addition of 20% of slag added, is also treated, not only thermally but also chemically (ESC TTQ), they further improve the properties of the composite material, the product is more compact, less porous, so the values are higher density, minors are absorptions and greater resistance in bending and compression, to the products obtained with the addition of slag only treated thermally. Reaching values of compressive resistance characteristic of the order of 109 MPa. The thermal conductivity values obtained are also higher. Testing technology with pieces of 160 x 30 x 5 mm and optimized composite material of clay 20% ESCTTQ, consisted in the determination of its expansion by moisture, efflorescence and frost resistance, in general, showing a better performance than the clay without additions. Thus, we have obtained new ceramic matrix composite materials for construction, improving its physical, mechanical and thermal properties, using aluminium slag secondary metallurgy, as an option Valuation of these wastes, thus preventing them from being poured to landfills and pollute environment.