Impact of fire and post-fire management techniques on soil chemical properties

The effects of fire ( Control burned soil) and two emergency stabilisation techniques (grass Seeding and straw Mulching ) on 20 chemical characteristics were evaluated on 0 – 5 cm top-soils sampled 1, 90, 180 and 365 days after an experimental fi re in a steep shrubland of a temperate-humid region (NW Spain). Most part of pH (in H 2 O and KCl) variance was explained by the sampling date. No clear temporal trends were identi fi able for total soil C and N content, likely due to the large SOM pool in these soils; however, changes on soil δ 13 C were explained by the deposition of 13 C-depleted ashes, followed by its progressive erosion, while those on soil δ 15 N were a consequence of fi re induced N outputs. After the fi re, NH 4 + – N, P, Na, K, Mg, Ca, Mn, Cu, Zn and B concentrations increased, while those of NO 3 − – N, Al, Fe and Co did not vary significantly. Despite a significant decline with time, concentrations of Mg, Ca and Mn at the end of the study were still higher than in unburned soil, while those of K, Cu, Zn and B were similar to the pre-fire levels and those of NH 4 + – N, P and Na were below pre-fire values. Mulching and Seeding treatments for burned soil emergency stabilisation had significant effects on soil δ 15 N and extractable K, Mg and Ca, while data were inconclusive for their possible effects on the extractable Al, Fe and Co

Forest Hydrology, Soil Conservation and Green Barriers in Canary Islands

In volcanic islands, the rainfall regime and its torrential nature, together with the steep slopes and the soil types present are considered to be some of the main factors affecting forest hydrology and soil conservation. In such environments, rain regime is generally irregular and characterized by short and intense rainfalls, which could cause destructive flows at times, followed by long periods of rain absence. The volcanic nature of these islands have as a direct resultant steep slopes which influences the runoff volume and speed, as well as the amount of topsoil susceptible to be detached and transported downstream. The soil type also affects the susceptibility to erosion processes. Andisols are the most typical soil on volcanic islands. Their particularities derive their mineral constituents, called short-range-order products, which provide these soils with an increased structural stability, which in turn reduces their susceptibility to erosion. However, the land use changes and the environmental factors such as rain regime and steep slopes may be determinant factor in destabilizing these soils and ultimately a cause for soil erosion and runoffs, which become a threat to the population downstream. Green barriers have been traditionally used to prevent or reduce these processes, also to enhance the dew effect and the fog water collection, and as a firebreak which acts as a barrier to slow or stop the progress of a wildfire. Wooded species present and subsequently their performance have a major influence on their effectiveness. The use of this natural erosion and fire control methods on volcanic islands is discussed in this paper.

Experiences on the specification of algorithms for fire and smoke control in road tunnels

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. The required immediate transition, from normal to emergency functioning of the ventilation equipments, is being strengthened by the use of automatic and semi-automatic control systems, what reduces the response times through the help to the operators, and the use of pre-defined strategies. A further step consists on the use of closed-loop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc.), optimizing smoke control capacity.

Experiences on using closed-loop control systems for smoke control

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. In the last years, the required quick response of the ventilation system, from normal to emergency mode, has been improved by the use of automatic and semi-automatic control systems, what reduces the response times through the support to the operators decision taking, and the use of pre-defined strategies. A further step consists on the use of closedloop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc), optimizing the quality of the smoke control process

Reduction of Nutrient Losses with Eroded Sediments by Post-Fire Soil Stabilisation Techniques

After an experimental fire in steep shrub land in a temperate–humid region (north-west Spain), the effects of two post-fire stabilisation treatments (grass seeding and straw mulching) on the chemical properties of eroded sediments,and the amount of nutrients lost with them, we reevaluated relative to control burnt soil, over a period of 13 months. Total C and N concentrations, and d 13 C, indicated that sediments were mainly contributed by charred plant and litter material. The highest concentrations of extractable base cations in the sediments occurred during the first 3 months following fire, especially for Na and K. As treatments had little or no effect on nutrient concentration in sediments, differences in nutrient losses were due to the 10-fold lower sediment production in mulching compared with other treatments. In control and seeding treatments, the accumulated amounts of nutrients lost with sediments were 989–1028kgha 1 (C), 77kgha 1 (N), 1.9–2.4kgha 1 (Ca), 0.9–1.1kgha 1 (Mg), 0.48–0.55kgha 1 (NH 4 þ –N), 0.39–0.56kgha 1 (K), 0.19–0.34kgha 1 (Na) and , 0.1kgha 1 (P and NO 3 –N) . These values accounted for 22–25% (total C and N) and 5–12% (NH 4 þ –N, Ca, P and Mg) of available nutrients in ash, and 1.0–2.4% of those in ash þ topsoil. As nutrient and sediment losses were strongly correlated, the reduction of the latter by mulching application leads to an effective decrease of post-fire nutrient losses.

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

Robust control of underactuated wheeled mobile manipulators using GPI disturbance observers

This article describes the design of a linear observer–linear controller-based robust output feedback scheme for output reference trajectory tracking tasks in the case of nonlinear, multivariable, nonholonomic underactuated mobile manipulators. The proposed linear feedback scheme is based on the use of a classical linear feedback controller and suitably extended, high-gain, linear Generalized Proportional Integral (GPI) observers, thus aiding the linear feedback controllers to provide an accurate simultaneous estimation of each flat output associated phase variables and of the exogenous and perturbation inputs. This information is used in the proposed feedback controller in (a) approximate, yet close, cancelations, as lumped unstructured time-varying terms, of the influence of the highly coupled nonlinearities, and (b) the devising of proper linear output feedback control laws based on the approximate estimates of the string of phase variables associated with the flat outputs simultaneously provided by the disturbance observers. Simulations reveal the effectiveness of the proposed approach.

Teaching automatic control in non-specialist engineering schools

Automatic Control Teaching in the new degree syllabus has reduced both, its contents and its implementation course, with regard to traditional engineering careers. On the other hand, where the qualification is not considered as automatic control specialist, it is required an adapted methodology to provide the minimum contents that the student needs to assimilate, even in the case that students do not perceive these contents as the most important in their future career. In this paper we present the contents of a small automatic course taught Naval Architecture and Marine Engineering Degrees at the School of Naval Engineering of the Polytechnic University of Madrid. We have included the contents covered using the proposed methodology which is based on practical work after lectures. Firstly, the students performed exercises by hand. Secondly, they solve the exercises using informatics support tools, and finally, they validate their previous results and their knowledge in the laboratory platforms.

An eco-friendly way to fire retardant flexible polyurethane foam: layer-by-layer assembly of fully bio-based substances

The objective of the present study is to develop fully renewable and environmentally benign techniques for improving the fire safety of flexible polyurethane foams (PUFs). A multilayered coating made from cationic chitosan (CS) and anionic alginate (AL) was deposited on PUFs through layer-by-layer assembly. This coating system exhibits a slight influence on the thermal stability of PUF, but significantly improves the char formation during combustion. Cone calorimetry reveals that 10 CS-AL bilayers (only 5.7% of the foams weight) lead to a 66% and 11% reduction in peak heat release rate and total heat release, respectively, compared with those of the uncoated control. The notable decreased fire hazards of PUF are attributed to the CS-AL coatings being beneficial to form an insulating protective layer on the surface of burning materials that inhibits the oxygen and heat permeation and slows down the flammable gases in the vapor phase, and thereby improves the flame resistance. This water-based, environmentally benign natural coating will stimulate further efforts in improving fire safety for a variety of polymer substrates.

Fishing effort control regulations influence on stability, safety and operability of small fishing vessels: study of a series of stability related accidents occurred in Spain between 2004 and 2007

Entre los años 2004 y 2007 se hundieron por problemas de estabilidad cinco pesqueros españoles de pequeña eslora, de características parecidas, de relativamente poca edad, que habían sido construidos en un intervalo de pocos años. La mayoría de los tripulantes de esos pesqueros fallecieron o desaparecieron en esos accidentes. Este conjunto de accidentes tuvo bastante repercusión social y mediática. Entre ingenieros navales y marinos del sector de la pesca se relacionó estos accidentes con los condicionantes a los diseños de los pesqueros impuestos por la normativa de control de esfuerzo pesquero. Los accidentes fueron investigados y publicados sus correspondientes informes; en ellos no se exploró esta supuesta relación. Esta tesis pretende investigar la relación entre esos accidentes y los cambios de la normativa de esfuerzo pesquero. En la introducción se expone la normativa de control de esfuerzo pesquero analizada, se presentan datos sobre la estructura de la flota pesquera en España y su accidentalidad, y se detallan los criterios de estabilidad manejados durante el trabajo, explicando su relación con la seguridad de los pesqueros. Seguidamente se realiza un análisis estadístico de la siniestralidad en el sector de la pesca para establecer si el conjunto de accidentes estudiados supone una anomalía, o si por el contrario el conjunto de estos accidentes no es relevante desde el punto de vista estadístico. Se analiza la siniestralidad a partir de diversas bases de datos de buques pesqueros en España y se concluye que el conjunto de accidentes estudiados supone una anomalía estadística, ya que la probabilidad de ocurrencia de los cinco sucesos es muy baja considerando la frecuencia estimada de pérdidas de buques por estabilidad en el subsector de la flota pesquera en el que se encuadran los cinco buques perdidos. A continuación el trabajo se centra en la comparación de los buques accidentados con los buques pesqueros dados de baja para construir aquellos, según exige la normativa de control de esfuerzo pesquero; a estos últimos buques nos referiremos como “predecesores” de los buques accidentados. Se comparan las dimensiones principales de cada buque y de su predecesor, resultando que los buques accidentados comparten características de diseño comunes que son sensiblemente diferentes en los buques predecesores, y enlazando dichas características de diseño con los requisitos de la nueva normativa de control del esfuerzo pesquero bajo la que se construyeron estos barcos. Ello permite establecer una relación entre los accidentes y el mencionado cambio normativo. A continuación se compara el margen con que se cumplían los criterios reglamentarios de estabilidad entre los buques accidentados y los predecesores, encontrándose que en cuatro de los cinco casos los predecesores cumplían los criterios de estabilidad con mayor holgura que los buques accidentados. Los resultados obtenidos en este punto permiten establecer una relación entre el cambio de normativa de esfuerzo pesquero y la estabilidad de los buques. Los cinco buques accidentados cumplían con los criterios reglamentarios de estabilidad en vigor, lo que cuestiona la relación entre esos criterios y la seguridad. Por ello se extiende la comparativa entre pesqueros a dos nuevos campos relacionados con la estabilidad y la seguridad delos buques: • Movimientos a bordo (operatividad del buque), y • Criterios de estabilidad en condiciones meteorológicas adversas El estudio de la operatividad muestra que los buques accidentados tenían, en general, una mayor operatividad que sus predecesores, contrariamente a lo que sucedía con el cumplimiento de los criterios reglamentarios de estabilidad. Por último, se comprueba el desempeño de los diez buques en dos criterios específicos de estabilidad en caso de mal tiempo: el criterio IMO de viento y balance intenso, y un criterio de estabilidad de nueva generación, incluyendo la contribución original del autor de considerar agua en cubierta. Las tendencias observadas en estas dos comparativas son opuestas, lo que permite cuestionar la validez del último criterio sin un control exhaustivo de los parámetros de su formulación, poniendo de manifiesto la necesidad de más investigaciones sobre ese criterio antes de su adopción para uso regulatorio. El conjunto de estos resultados permite obtener una serie de conclusiones en la comparativa entre ambos conjuntos de buques pesqueros. Si bien los resultados de este trabajo no muestran que la aprobación de la nueva normativa de esfuerzo pesquero haya significado una merma general de seguridad en sectores enteros de la flota pesquera, sí se concluye que permitió que algunos diseños de buques pesqueros, posiblemente en busca de la mayor eficiencia compatible con dicha normativa, quedaran con una estabilidad precaria, poniendo de manifiesto que la relación entre seguridad y criterios de estabilidad no es unívoca, y la necesidad de que éstos evolucionen y se adapten a los nuevos diseños de buques pesqueros para continuar garantizando su seguridad. También se concluye que la estabilidad es un aspecto transversal del diseño de los buques, por lo que cualquier reforma normativa que afecte al diseño de los pesqueros o su forma de operar debería estar sujeta a evaluación por parte de las autoridades responsables de la seguridad marítima con carácter previo a su aprobación. ABSTRACT Between 2004 and 2007 five small Spanish fishing vessels sank in stability related accidents. These vessels had similar characteristics, had relatively short age, and had been built in a period of a few years. Most crewmembers of these five vessels died or disappeared in those accidents. This set of accidents had significant social and media impact. Among naval architects and seamen of the fishing sector these accidents were related to the design constraints imposed by the fishing control effort regulations. The accidents were investigated and the official reports issued; this alleged relationship was not explored. This thesis aims to investigate the relationship between those accidents and changes in fishing effort control regulations. In the introduction, the fishing effort control regulation is exposed, data of the Spanish fishing fleet structure and its accident rates are presented, and stability criteria dealt with in this work are explained, detailing its relationship with fishing vessel safety. A statistical analysis of the accident rates in the fishing sector in Spain is performed afterwards. The objective is determining whether the set of accidents studied constitute an anomaly or, on the contrary, they are not statistically relevant. Fishing vessels accident rates is analyzed from several fishing vessel databases in Spain. It is concluded that the set of studied accidents is statistically relevant, as the probability of occurrence of the five happenings is extremely low, considering the loss rates in the subsector of the Spanish fishing fleet where the studied vessels are fitted within. From this point the thesis focuses in comparing the vessels lost and the vessels that were decommissioned to build them as required by the fishing effort control regulation; these vessels will be referred to as “predecessors” of the sunk vessels. The main dimensions between each lost vessel and her predecessor are compared, leading to the conclusion that the lost vessels share design characteristics which are sensibly different from the predecessors, and linking these design characteristics with the requirements imposed by the new fishing control effort regulations. This allows establishing a relationship between the accidents and this regulation change. Then the margin in fulfilling the regulatory stability criteria among the vessels is compared, resulting, in four of the five cases, that predecessors meet the stability criteria with greater clearance than the sunk vessels. The results obtained at this point would establish a relationship between the change of fishing effort control regulation and the stability of vessels. The five lost vessels complied with the stability criteria in force, so the relation between these criteria and safety is put in question. Consequently, the comparison among vessels is extended to other fields related to safety and stability: • Motions onboard (operability), and • Specific stability criteria in rough weather The operability study shows that the lost vessels had in general greater operability than their predecessors, just the opposite as when comparing stability criteria. Finally, performance under specific rough weather stability criteria is checked. The criteria studied are the IMO Weather Criterion, and one of the 2nd generation stability criteria under development by IMO considering in this last case the presence of water on deck, which is an original contribution by the author. The observed trends in these two cases are opposite, allowing to put into question the last criterion validity without an exhaustive control of its formulation parameters; indicating that further research might be necessary before using it for regulatory purposes. The analysis of this set of results leads to some conclusions when comparing both groups of fishing vessels. While the results obtained are not conclusive in the sense that the entry into force of a new fishing effort control in 1998 caused a generalized safety reduction in whole sectors of the Spanish fishing fleet, it can be concluded that it opened the door for some vessel designs resulting with precarious stability. This evidences that the relation between safety and stability criteria is not univocal, so stability criteria needs to evolve for adapting to new fishing vessels designs so their safety is still guaranteed. It is also concluded that stability is a transversal aspect to ship design and operability, implying that any legislative reform affecting ship design or operating modes should be subjected to assessing by the authorities responsible for marine safety before being adopted.

Modelado dinámico y control de maniobras de dispositivos submarinos

Es bien conocido por todos que la Primera Revolución Industrial, que tuvo su inicio en la segunda mitad del Siglo XVIII, conllevó un aumento del uso de los recursos energéticos que no se ha detenido para llegar a los niveles de desarrollo tecnológico, industrial y de calidad de vida, de los que se dispone en la actualidad. A simple vista podría intuirse que para disponer de un mayor nivel tecnológico, industrial, de confort, etc. sea necesario un mayor consumo de energía primaria. La actual generación de energía está principalmente basada en el procesamiento de los diversos compuestos del carbono (hidrocarburos, gases y productos derivados del petróleo), que son contaminantes y además, se agotan. Desde hace unas pocas décadas, la humanidad ha sido consciente que es necesario generar energía a partir de fuentes de origen renovable, y que además resulten menos contaminantes. Así, en la actualidad, se ha llegado a un estado de desarrollo avanzado para la explotación de diversas fuentes de energías como la eólica, a la vez que se comienza a mirar con realismo la posibilidad de explotación de diversas energías de origen marino. Se considera que las energías renovables procedentes de los océanos que se encuentran más desarrolladas tecnológicamente hablando, sin tener en cuenta la energía eólica fuera costa (offshore), son la denominada energía undimotriz o de las olas y la energía de las corrientes marinas, no necesariamente en este orden. El trabajo propuesto en esta Tesis se centra en este último recurso energético y, aunque no se dispone todavía de ningún dispositivo en fase de explotación comercial, la concepción, diseño y desarrollo de dispositivos para la extracción de energía de las corrientes, y su evolución, han sido relativamente rápidos e importantes en estos últimos años. Existen ya diferentes dispositivos en fase de pruebas con resultados muy prometedores. Aunque los dispositivos actuales se encuentran limitados a la explotación energética en zonas de poca profundidad, los diferentes estudios del recurso indican la necesidad de explotar corrientes marinas a mayores profundidades, para lo que se están desarrollando actualmente dispositivos, cuya evolución en lo que a sistemas de fondeo se refiere, está siendo muy parecida a la que se ha producido en los parques eólicos fuera costa, similar a su vez, a la evolución llevada a cabo en las plataformas oceánicas para la explotación de recursos petrolíferos (denominados oil & gas) que se extraen de profundidades cada vez mayores. Las soluciones tecnológicas que resulten válidas han de ser también económicamente viables, y en la actualidad se requiere todavía reducir costos en todas las fases de instalación, explotación y mantenimiento de estos dispositivos, sea cual sea su profundidad de operación. Uno de los focos de estudio para abaratar los costes de explotación en general, pasa por abaratar y reducir los costes en las maniobras necesarias de inmersión (de la superficie del mar a la profundidad de operación) y emersión (de la profundidad de operación a la superficie del mar) de estos dispositivos, para llevar a cabo tareas de mantenimiento in situ, en el mar, y sin necesidad de buques especializados ni de su transporte a tierra. En esta Tesis se propone, en primer lugar, un método para evaluar el ciclo de vida de diversos dispositivos de aprovechamiento de las corrientes marinas. Se evidencia que el coste de la energía así generada sigue siendo no plenamente competitivo, por lo que se requiere avanzar en el abaratamiento de costes, principalmente en la instalación y en su mantenimiento. Para ello se propone como novedad principal, introducir sistemas de control en lazo cerrado para realizar maniobras de instalación y mantenimiento de forma automática. También se aporta un modelo dinámico original y muy sencillo para dispositivos bajo estos movimientos de emersión/inmersión, a partir del cual se han desarrollado los algoritmos de control para el propósito mencionado, que no es otro sino automatizar en todo lo posible las maniobras completas. Los algoritmos de control propuestos han sido validados mediante simulación. Se proponen trayectorias de referencia de movimiento suaves (smooth) similares a las utilizadas en robótica. Estos movimientos de cambios de profundidad en lazo cerrado, combinados con secuencias de movimientos en bucle abierto para cuando el dispositivo interacciona en la superficie libre, han dado lugar a nuevas maniobras completas de instalación y mantenimiento que se presentan en esta Tesis, diferentes a las actuales. Finalmente, y como justificación de la viabilidad económica del método novedoso aportado, se ha realizado un estudio comparativo de los costes de la tecnología propuesta, frente a la tecnología actual. Este nuevo sistema de maniobras automáticas implica un ciclo de vida diferente para los dispositivos de aprovechamiento de la energía de las corrientes, ciclo que se cuantifica a partir de un dispositivo base que ha sido modificado y adaptado para la nueva tecnología propuesta, demostrando su viabilidad tanto técnica como económica. ABSTRACT It’s well known that the First Industrial Revolution started in the second half of the eighteenth century, carried the increasing of the use of energy resource which have not been stopped until reach the present technology, industrial evolution and daily life quality. On the surface, it can be known intuitively that a higher consumption of primary energy resource is demanded for benefiting from a higher technological industrial and daily life level. Today, the generation of energy is mainly based in the processing of carbon products (hydrocarbons, gases and petroleum products) which are pollutants, and additionally, are depleted. From a few decades ago, the humanity is aware the energy should be obtained from renewable resources, which besides, should be cleaner. So, at the present, a technical develop has been gained to exploit several energy source, as wind energy, and, at the same time, the extraction of the marine energy starts to seem as a reality. The renewable marine energies considered more advanced and technically developed, without keeping in mind, the offshore wind energy, are the wave energy and the tidal current energy, not necessarily in that order. This Thesis is focused in this last energy resource, and, although, any device is under commercial operation, the concept, design and develop of this type of devices to extract the tidal current energy and their evolution has been comparatively fast and important the last years. There are several devices under test with promising results. Even through the current devices are limited to lower depth areas, the several studies of the tidal energy resource suggest the need to exploit the marine current at greater depths to what is being developed devices, where their evolution in the anchoring system is being very similar to the evolution performed in the offshore wind farms, which is at the same time, similar to the evolution in the oil and gas exploitation which are extracted to greatest depths. Viable technical solutions should be also viable economically and nowadays the cost in all phases of the project (installation, maintenance and operation) should be decreased whatever the operation depth is. One focus of study to lower the operation cost is the cost decreasing of immersion manoeuvring operations (from sea surface to the operation depth) and immersion manoeuvring operations (from operation depth to the sea surface), therefore the maintenance operations can be performed on – site, in the sea, and no specialized vessels are required to transport the devices from the sea to shore. In this dissertation, firstly is proposed a method to evaluate the life cycle of the tidal energy current devices. It is proved the energy generated by these devices is not fully competitive; therefore, the cost falling is mainly an objective in the installation and the maintenance operations. For that, it is proposed as main novelty, the using of closed loop control systems to perform the automatic installation and manoeuvring operations. It is also contributed with an original and simple dynamic model and for controlling the immersion/emersion movements of these devices, from which the control algorithms are developed in order to automate as much as possible the complete manoeuvring. The control algorithms proposed has been validated by simulations. Reference paths with smooth movements, similar which are used in robotics, are suggested. These movements to change the depth using closed loop control, combined with the sequences in open loop movements when the device is in free surface, have been development for a new complete manoeuvring to installation and maintenance operations which are advanced in this Thesis and they are different to the present manoeuvrings. Finally and as justification of the economic viability of this original method, a comparative cost study between the technology proposed and the current technology is performed. This new automatic manoeuvring system involves a different life cycle for the tidal energy current devices, cycle that is quantified from a base device which has been modified and adapted for the new proposed technology, showing the technical and economic viability.

Sistema de control y visualización de información sobre riesgo de incendios

Una red inalámbrica de sensores (Wireless Sensor Network, WSN) constituye un sistema de comunicación de datos flexible utilizado como alternativa a las redes cableadas o como extensión de éstas. Una de las aplicaciones de estas redes es para su uso en sistemas de predicción y prevención de incendios en áreas naturales. Su implementación se basa en el despliegue de sensores inalámbricos, realizado en una zona de riesgo de incendio que puedan recolectar información tal como temperatura, humedad y presión. Desde una estación base (o nodo "sumidero"), se suministra la información de los sensores a un centro de monitorización y control de forma estructurada. En estos centros la información recibida puede ser analizada, procesada y visualizada en tiempo real. Desde este centro de control se puede controlar también la red WSN modificando el comportamiento de los sensores según el nivel de riesgo de incendio detectado. Este proyecto se basa en el diseño, desarrollo e implementación de un Sistema de Control y Visualización de Información sobre Riesgo de Incendio (SCVIRI), que implementa las funciones de los centros de monitorización y control. La implementación de este sistema, junto con el desarrollado, en paralelo, de otro proyecto denominado Sistema de Estimación de Riesgo de Incendio Utilizando una WSN (SERIUW) que implementa la emulación de la red WSN, conforman un sistema general de anticipación y seguimiento de Fuegos. Se han realizado pruebas de funcionalidad y eficacia, incluidas en la presente memoria del sistema general (ambos proyectos), en un entorno controlado simulado. Este sistema es una solución para la lucha contra los incendios forestales ya que predice y previene, de forma temprana, posibles incendios en las áreas naturales bajo supervisión. Ante un evento de incendio declarado este sistema es un poderoso instrumento de apoyo permitiendo, por un lado, generar alertas automáticas (con localización y gravedad de fuegos detectados) y por el otro, hacer un seguimiento del incendio con mapas en tiempo real (con su consecuente apoyo para la protección e información con las brigadas de bomberos en las zonas activas). ABSTRACT. A wireless sensor network (WSN) is a flexible data communication system used as an alternative to wired networks or as an extension of them. One possible application of these networks is related to fire prediction and prevention in natural areas. Its implementation is based on a deployment of wireless sensors, in an area with high or moderate fire risk, to collect information such as temperature, humidity, luminance and pressure. A base station (or "sink") sends the collected information to a monitoring and control center according to an agreed structured format. At this center, the information received can be analyzed, processed and displayed in real time by using monitoring systems. From this control center the WSN can also be controlled by changing the sensors behavior in consistence with the detected level of fire risk. The work carried out in this project consists on the design, development and implementation of a system named SCVIRI, which implements the functions of the aforementioned monitoring and control center. This system works in connection with other one, called SERIUW, which has been developed in a different project and implements the WSN in an emulated environment. These two systems working together make up a general system of anticipation and monitoring of fires. This document also includes the functionality and performance tests performed on the overall system in a controlled and simulated environment. The global system is a solution that makes it easier to predict and prevent possible fires in natural areas under supervision. This system can be a powerful tool since, before a fire event is declared, it generates automatic alerts (including location and severity information) and allows the real-time motorization of fire evolution and its graphical visualization on maps. This could be also very useful for providing fire brigades with support, protection and information in zones in which a fire is already active.

Estudio de los parámetros necesarios para establecer las medidas de actuación por tipos de buques en situaciones de emergencia después de un accidente

La “Actuación en la Crisis”, objetivo principal de esta tesis, trata de establecer y concretar los procedimientos y apoyos desde tierra y a bordo de los buques, tanto técnicos como operacionales, a seguir por el Capitán y tripulación de un buque después de un accidente, en especial cuando el buque tiene un riesgo importante de hundimiento o necesidad de abandono. La aparición de este concepto es relativamente reciente, es decir desde el año 1995, después de los estudios y propuestas realizados, por el Panel de Expertos de IMO, como consecuencia del hundimiento del buque de pasaje y carga rodada, Estonia, en el que perdieron la vida más de 850 personas a finales de Septiembre de 1994. Entre las propuestas recomendadas y aceptadas por los gobiernos en la Conferencia Internacional SOLAS 1995, figuraba este concepto novedoso, que luego fue adoptado de una forma generalizada para todos los tipos de buques, que hasta entonces sólo disponían de documentos dispersos y a veces contradictorios para la actuación en estos momentos de peligro, que dio lugar a un profundo tratamiento de este problema, que iba a afectar a los buques, tanto en los conceptos y parámetros de proyecto, como a la propia operación del buque. La tesis desarrolla los fundamentos, estado del arte, implantación y consecuencias sobre la configuración y explotación del buque, que han dado lugar a una serie de documentos, que se han incluido en diversos Convenios Internacionales, Códigos y otros documentos de obligada aplicación en la industria naval generados en IMO (SOLAS, Retorno Seguro a Puerto, Plano y Libro de Control de Averías, ISM). La consecuencia más novedosa e interesante de este concepto ha sido la necesidad de disponer cada compañía explotadora del buque, de un servicio importante de “apoyo en la crisis”, que ha dado lugar a implantar un “servicio de emergencia especial”, disponible las 24 horas del día y 365 de año que ofrecen las Sociedades de Clasificación. El know-how de los accidentes que tratan estos servicios, hacen que se puedan establecer ciertas recomendaciones, que se centran, en que el buque tenga, por sus propios medios, una posibilidad de aumentar el KM después de una avería, la garantía de la resistencia estructural adecuada y el aumento del tiempo de hundimiento o el tiempo de mantenimiento a flote (otro tipo de averías vinculadas con la maquinaria, equipo o protección y lucha contra incendios, no son objeto de tesis). Las conclusiones obtenidas, son objeto de discusión especialmente en IACS e IMO, con el fin de establecer las aplicaciones pertinentes, que permitan dar al buque una mayor seguridad. Como objetivo principal de esta tesis es establecer estos puntos de mejora consecuencia de esta actuación en la crisis, con la aportación de varias soluciones que mejorarían los problemas mencionados para los tres tipos de buques que consideramos más importantes (pasaje, petroleros y bulkcarriers) La tesis recorre, desde el principio en 1995, la evolución de esta actuación en la crisis, hasta el momento actual., los puntos básicos que se establecen, que van muy de la mano de la llamada “cultura de seguridad”, objetivo nacido durante los años 90, con el fin de implantar una filosofía distinta para abordar el tratamiento de la seguridad del buque, a la que se venía aplicando hasta el momento, en donde se contemplaba tratar el tema de forma singular y específica para cada caso. La nueva filosofía, trataba de analizar el problema, desde un aspecto global y por tanto horizontal, realizando un estudio exhaustivo de las consecuencias que tendría la aplicación de una nueva medida correctora, en los restantes equipos y sistemas del buque., relativos al proyecto, configuración, operación y explotación del buque. Se describen de manera sucinta las profundas investigaciones a que dio lugar todo lo anterior, estando muchas de ellas, vinculadas a grandes proyectos europeos. La mayor parte de estos proyectos fueron subvencionados por la Comunidad Económica Europea durante la primera década del siglo actual. Dentro de estas investigaciones, donde hay que destacar la participación de todos los agentes del sector marítimo europeo, se hacen imprescindibles la utilización de dos herramientas novedosas para nuestro sector, como son el “Estudio de Riesgos” y la “Evaluación de la Seguridad”, más conocida técnicamente por su nombre ingles “Safety Assessment”, cuyos principios también son incluidos en la tesis. Además se especifican las bases sobre las que se establecen la estabilidad intacta y en averías, con nuevos conceptos, no tratados nunca hasta entonces, como la “altura crítica de agua en cubierta” para la cual el buque se hundiría sin remisión, “estado de la mar” en la que se puede encontrar el buque averiado, el cálculo del tiempo de hundimiento, u otros aspectos como el corrimiento de la carga, o bien el tratamiento de los problemas dinámicos en el nuevo “Código de Estabilidad Intacta”. Con respecto a la resistencia estructural, especialmente el estudio de la “resistencia estructural después de la avería”, que tiene en cuenta el estado de la mar en la que se encontraría el buque afectado. Se analizan los tipos de buques mencionados uno por uno y se sacan, como aportación fundamental de esta tesis, separadamente, las acciones y propuestas a aplicar a estos buques. En primer lugar, las relativas al proyecto y configuración del buque y en segundo lugar, las de operación, explotación y mantenimiento, con el fin de acometer, con garantías de éxito, la respuesta a la ayuda en emergencia y la solución a la difícil situación que pueden tener lugar en condiciones extremas. Para ver el efecto de algunas de las propuestas que se incluyen, se realizan y aplican concretamente, a un buque de pasaje de carga rodada, a un petrolero y a un bulkcarrier, para demostrar el mejor comportamiento de estos buques en situación de emergencia. Para ello se han elegido un buque ejemplo para cada tipo, efectuándose los cálculos de estabilidad y resistencia longitudinal y comparar la situación, en la que quedaría el buque averiado, antes y después de la avería. La tesis se completa con una estadística real de buques averiados de cada uno de estos tres tipos, distinguiendo el tipo de incidente y el número de los buques que lo han sufrido, considerándose como más importantes los incidentes relacionados con varadas, colisiones y fuego resumiéndose lo más relevante de esta aportación también importante de esta tesis. ABSTRACT The "Response in an emergency" is the main objective of this thesis, it seeks to establish and define procedures for technical and operational support onboard and shore, to be followed by the captain and crew on of a ship after an accident, especially when the ship has a significant risk of sinking or a need to abandon it. The emergence of this concept is relatively recent, in 1995, after studies and proposals made by the Panel of Experts IMO, following the sinking of the “Estonia” vessel, where more than 850 people died in late September 1994. In the International Convention SOLAS 1995, among the recommended proposals and accepted regulations, this new concept was included, which was later adopted for all types of ships which until then had only scattered some documents, sometimes including contradictory actions in emergency situations. This led to a profound treatment of this problem, which would affect the vessels in both the concepts and design parameters, as to the proper operation of the vessel. The thesis develops the foundations, state of the art, implementation and consequences on the design and operation of the vessel, this has led to a series of Circulars and Regulations included in several International Codes and Conventions issued by IMO which are required to be complied with (SOLAS Safe Return to Port, Damage Control Plan and Booklet, ISM). The most novel and interesting consequence of this concept has been the need for every company operating the ship to have a shore based support service in emergency situations which has led to implement special emergency services offered by Class Societies which are available 24 hours a day, 365 days per year. The know-how of these services dealing with all types of accidents can establish certain recommendations, which focus on the ship capability to increase the KM after damage. It can also be determined adequate structural strength and the increase of the capsizing time or time afloat (other types of damages associated with the machinery, equipment or firefighting, are not the subject of this thesis). The conclusions are discussed especially in IACS and IMO, in order to establish appropriate applications to improve the security of the vessels. The main objective of this thesis is to establish actions to improve emergency actions, resulting from different responses in the crisis, with the contribution of several solutions that improve the problems mentioned for three types of ships that we consider most important (passenger vessels, tankers and bulk carriers) The thesis runs from the beginning in 1995 to date, the evolution of the response on the crisis. The basics established during the 90s with the "safety culture" in order to implement a different philosophy to address the treatment of the safety of the ship, which was being previously implemented, as something singular and specific to each case. The new philosophy tried to analyse the problem from a global perspective, doing an exhaustive study of the consequences of the implementation of the new regulation in the ship systems and equipment related to the design, configuration and operation of the vessel. Extensive investigations which led to the above are described, many of them being linked to major European projects. Most of these projects were funded by the European Union during the first decade of this century. Within these investigations, which it must be highlighted the participation of all players in the European maritime sector, a necessity to use two new tools for our industry, such as the "Risk Assessment" and "Safety Assessment" whose principles are also included in the thesis. The intact and damage stability principles are established including new concepts, never treated before, as the "critical height of water on deck" for which the ship would sink without remission, "sea state" where the damaged vessel can be found, calculation of capsizing time, or other aspects such cargo shifting or treatment of dynamic problems in the new Intact Stability Code in development. Regarding the structural strength, it has to be especially considered the study of the "residual strength after damage", which takes into account the state of the sea where the vessel damaged can be found. Ship types mentioned are analysed one by one, as a fundamental contribution of this thesis, different actions and proposals are established to apply to these types of vessels. First, those ones relating to the design and configuration of the vessel and also the ones related to the operation and maintenance in order to support successfully responses to emergency situations which may occur in extreme situations. Some of the proposals are applied specifically to a RoRo passenger ship, an oil tanker and a bulkcarrier, to demonstrate the improved performance of these vessels damaged. An example for each type vessel has been chosen, carrying out stability and longitudinal strength calculations comparing the situation of the ship before and after damage. The thesis is completed with incidents statics for each of these three types, distinguishing the type of incident and the number of ships having it. The most important incidents considered are the ones related to groundings, collisions and fire being this other relevant contribution of this thesis.