Impact And Explosive Loads On Concrete Buildings Using Shell And Beam Type Elements

The threat of impact or explosive loads is regrettably a scenario to be taken into account in the design of lifeline or critical civilian buildings. These are often made of concrete and not specifically designed for military threats. Numerical simulation of such cases may be undertaken with the aid of state of the art explicit dynamic codes, however several difficult challenges are inherent to such models: the material modeling for the concrete anisotropic failure, consideration of reinforcement bars and important structural details, adequate modeling of pressure waves from explosions in complex geometries, and efficient solution to models of complete buildings which can realistically assess failure modes. In this work we employ LS-Dyna for calculation, with Lagrangian finite elements and explicit time integration. Reinforced concrete may be represented in a fairly accurate fashion with recent models such as CSCM model [1] and segregated rebars constrained within the continuum mesh. However, such models cannot be realistically employed for complete models of large buildings, due to limitations of time and computer resources. The use of structural beam and shell elements for this purpose would be the obvious solution, with much lower computational cost. However, this modeling requires careful calibration in order to reproduce adequately the highly nonlinear response of structural concrete members, including bending with and without compression, cracking or plastic crushing, plastic deformation of reinforcement, erosion of vanished elements etc. The main objective of this work is to provide a strategy for modeling such scenarios based on structural elements, using available material models for structural elements [2] and techniques to include the reinforcement in a realistic way. These models are calibrated against fully three-dimensional models and shown to be accurate enough. At the same time they provide the basis for realistic simulation of impact and explosion on full-scale buildings

On loader productivity, rock strength and explosive energy in metal mining

Twenty production blasts in two open pit mines were monitored, in rocks with medium to very high strength. Three different blasting agents (ANFO, watergel and emulsion blend) were used, with powder factors ranging between 0.88 and 1.45 kg/m3. Excavators were front loaders and rope shovels. Mechanical properties of the rock, blasting characteristics and mucking rates were carefully measured. A model for the calculation of the productivity of excavators is developed thereof, in which the production rate results as a product of an ideal, maximum, productivity rate times an operating efficiency. The maximum rate is a function of the dipper capacity and the efficiency is a function of rock density, strength, and explosive energy concentration in the rock. The model is statistically significant and explains up to 92 % of the variance of the production rate measurements.

Asymmetric propagation of airblast from bench blasting

This paper investigates the propagation of airblast from quarry blasting. Peak overpressure is calculated as a function of blasting parameters (explosive mass per delay and velocity at which the detonation sequence proceeds along the bench) and polar coordinates of the point of interest (distance to the blast and azimuth with respect to the free face of the blast). The model is in the form of the product of a classical scaled distance attenuation law times a directional correction factor. The latter considers the influence of the bench face, and attenuates overpressure at the top level and amplifies it at the bottom. Such factor also accounts for the effect of the delay by amplifying the pressure in the direction of the initiation sequence if the velocity of initiation exceeds half the speed of sound and up to an initiation velocity in the range of the speed of sound. The model has been fitted to an empirical data set composed by 134 airblast records monitored in 47 blasts at two quarries. The measurements were made at distances to the blast less than 450 m. The model is statistically significant and has a determination coefficient of 0.869

Estudio de la capacidad de arranque de una dinamita gelatinosa frente a una dinamita de seguridad

The objective of this project is to show that the permissible explosive called 20 SR is able to pull out the coal in the normal conditions of blasting in a satisfactory way and to set up the equivalence between the 20 SR and gelatin dynamite (Goma 2 ECO). To achieve this goal some blasting were done, changing the conditions of the blasting and the powder factor for the 20 SR. To analyze the fragmentation base on the analysis of the images of the rock blasted, a commercial software was used. The results from this analysis were compared with the results from the theoretical model for fragmentation created by Kuz – Ram. After all, it was showed that the 20 SR explosive is able to pull out the coal for different coal rock compositions. As the result of this project we can conclude that the 20 SR seems to be able to pull out the coal in normal blasting conditions, using the powder factor as a proportion of the “ballistic mortar” between the two explosives.

Estudio de vibraciones de las voladuras de producción en la cantera de Buruntza y su afección sobre el tramo de la red ferroviaria Andoain – Urnieta (País Vasco)

El estudio de vibraciones tiene por objetivo fijar una banda de seguridad para proteger la nueva línea ferroviaria de alta velocidad Madrid – Vitoria – San Sebastián (tramo Andoain – Urnieta).Las tomas de datos han permitido el cálculo de unas leyes de amortiguación de la propagación de las ondas de vibración que permiten predecir cuál será la magnitud de vibración generada a una cierta distancia de la explotación cuando se detona una carga de explosivo determinada. Así mismo, se lleva a cabo un análisis de las concentraciones de energía (vibraciones) que podrían producirse durante una voladura tipo de producción atendiendo a diferentes secuencias de disparo. Con este método, basado en el disparo de un “barreno semilla” de similares condiciones de carga y arranque que un barreno típico de producción, se pretende resaltar la importancia que tiene el rango de las frecuencias en el proceso de generación y transmisión de vibraciones en el terreno, y consecuentemente en los criterios de protección de estructuras frente a tales vibraciones. ABSTRACT The aim of the vibration study is to set a security band to protect the Spanish high speed train (AVE) which goes Madrid-Vitoria-San Sebastian (section Andoain- Urnieta). The data gathered has made possible the calculation of absorption laws of propagation of vibrating waves, that allow the prediction of the magnitude created at a certain distance of the detonation of a known explosive. In addition, an analysis of the energy concentrations that could appear during a blasting in different sequences is made. With this method based on the firing of a seed drill with similar load and boot conditions of a common production drill, is intended to highlight the importance of the frequency range in the process of vibrations transmission and generation in the field, and consequently the importance in the structures protection criteria against these vibrations.

Estudio de la capacidad de arranque de una dinamita gelatinosa frente a una dinamita de seguridad

El presente proyecto pretende demostrar que el explosivo de seguridad 20 SR es capaz de arrancar el carbón de forma satisfactoria en las condiciones de disparo habituales y establecer la equivalencia práctica de dicho explosivo con una dinamita gelatinosa (Goma 2ECO). Para conseguir este objetivo se realizaron una serie de voladuras, variando las condiciones de disparo y los consumos específicos de la dinamita de seguridad. Se utilizó un software de análisis fotográfico para el estudio de la fragmentación en la pila y también se compararon los resultados obtenidos con el modelo teórico de fragmentación de Kuz – Ram. Los resultados demostraron la capacidad de arranque de la dinamita de seguridad, para diferentes composiciones de carbón. Del estudio parece deducirse que la dinamita de seguridad 20 SR es capaz de arrancar el carbón en condiciones de disparo habituales utilizando un consumo específico proporcional a la relación de la potencia del péndulo balístico de ambos explosivos. ABSTRACT The objective of this project is to show that the permissible explosive called 20 SR is able to pull out the coal in the normal conditions of blasting in a satisfactory way and to set up the equivalence between the 20 SR and gelatin dynamite (Goma 2 ECO). To achieve this goal some blasting were done, changing the conditions of the blasting and the powder factor for the 20 SR. To analyze the fragmentation base on the analysis of the images of the rock blasted, a commercial software was used. The results from this analysis were compared with the results from the theoretical model for fragmentation created by Kuz – Ram. After all, it was showed that the 20 SR explosive is able to pull out the coal for different coal rock compositions. As the result of this project we can conclude that the 20 SR seems to be able to pull out the coal in normal blasting conditions, using the powder factor as a proportion of the “ballistic mortar” between the two explosives.

Prediction of near field overpressure from quarry blasting

This paper investigates the propagation of airblast or pressure waves in air produced by bench blasting (i.e. detonation of the explosive in a row of blastholes, breaking the burden of rock towards the free vertical face of the block). Peak overpressure is calculated as a function of blasting parameters (explosive mass per delay and velocity at which the detonation sequence proceeds along the bench) and the polar coordinates of the position of interest (distance to the source and azimuth with respect to the free face). The model has been fitted to empirical data using linear least squares. The data set is composed of 122 airblast records monitored at distances less than 400 m in 41 production blasts carried out in two quarries. The model is statistically significant and has a determination coefficient of 0.87. The formula is validated from 12 airblast measurements gathered in five additional blasts.

Experimental and numerical analysis of reinforced concrete elements subjected to blast loading

El hormigón es uno de los materiales de construcción más empleados en la actualidad debido a sus buenas prestaciones mecánicas, moldeabilidad y economía de obtención, entre otras ventajas. Es bien sabido que tiene una buena resistencia a compresión y una baja resistencia a tracción, por lo que se arma con barras de acero para formar el hormigón armado, material que se ha convertido por méritos propios en la solución constructiva más importante de nuestra época. A pesar de ser un material profusamente utilizado, hay aspectos del comportamiento del hormigón que todavía no son completamente conocidos, como es el caso de su respuesta ante los efectos de una explosión. Este es un campo de especial relevancia, debido a que los eventos, tanto intencionados como accidentales, en los que una estructura se ve sometida a una explosión son, por desgracia, relativamente frecuentes. La solicitación de una estructura ante una explosión se produce por el impacto sobre la misma de la onda de presión generada en la detonación. La aplicación de esta carga sobre la estructura es muy rápida y de muy corta duración. Este tipo de acciones se denominan cargas impulsivas, y pueden ser hasta cuatro órdenes de magnitud más rápidas que las cargas dinámicas impuestas por un terremoto. En consecuencia, no es de extrañar que sus efectos sobre las estructuras y sus materiales sean muy distintos que las que producen las cargas habitualmente consideradas en ingeniería. En la presente tesis doctoral se profundiza en el conocimiento del comportamiento material del hormigón sometido a explosiones. Para ello, es crucial contar con resultados experimentales de estructuras de hormigón sometidas a explosiones. Este tipo de resultados es difícil de encontrar en la literatura científica, ya que estos ensayos han sido tradicionalmente llevados a cabo en el ámbito militar y los resultados obtenidos no son de dominio público. Por otra parte, en las campañas experimentales con explosiones llevadas a cabo por instituciones civiles el elevado coste de acceso a explosivos y a campos de prueba adecuados no permite la realización de ensayos con un elevado número de muestras. Por este motivo, la dispersión experimental no es habitualmente controlada. Sin embargo, en elementos de hormigón armado sometidos a explosiones, la dispersión experimental es muy acusada, en primer lugar, por la propia heterogeneidad del hormigón, y en segundo, por la dificultad inherente a la realización de ensayos con explosiones, por motivos tales como dificultades en las condiciones de contorno, variabilidad del explosivo, o incluso cambios en las condiciones atmosféricas. Para paliar estos inconvenientes, en esta tesis doctoral se ha diseñado un novedoso dispositivo que permite ensayar hasta cuatro losas de hormigón bajo la misma detonación, lo que además de proporcionar un número de muestras estadísticamente representativo, supone un importante ahorro de costes. Con este dispositivo se han ensayado 28 losas de hormigón, tanto armadas como en masa, de dos dosificaciones distintas. Pero además de contar con datos experimentales, también es importante disponer de herramientas de cálculo para el análisis y diseño de estructuras sometidas a explosiones. Aunque existen diversos métodos analíticos, hoy por hoy las técnicas de simulación numérica suponen la alternativa más avanzada y versátil para el cálculo de elementos estructurales sometidos a cargas impulsivas. Sin embargo, para obtener resultados fiables es crucial contar con modelos constitutivos de material que tengan en cuenta los parámetros que gobiernan el comportamiento para el caso de carga en estudio. En este sentido, cabe destacar que la mayoría de los modelos constitutivos desarrollados para el hormigón a altas velocidades de deformación proceden del ámbito balístico, donde dominan las grandes tensiones de compresión en el entorno local de la zona afectada por el impacto. En el caso de los elementos de hormigón sometidos a explosiones, las tensiones de compresión son mucho más moderadas, siendo las tensiones de tracción generalmente las causantes de la rotura del material. En esta tesis doctoral se analiza la validez de algunos de los modelos disponibles, confirmando que los parámetros que gobiernan el fallo de las losas de hormigón armado ante explosiones son la resistencia a tracción y su ablandamiento tras rotura. En base a los resultados anteriores se ha desarrollado un modelo constitutivo para el hormigón ante altas velocidades de deformación, que sólo tiene en cuenta la rotura por tracción. Este modelo parte del de fisura cohesiva embebida con discontinuidad fuerte, desarrollado por Planas y Sancho, que ha demostrado su capacidad en la predicción de la rotura a tracción de elementos de hormigón en masa. El modelo ha sido modificado para su implementación en el programa comercial de integración explícita LS-DYNA, utilizando elementos finitos hexaédricos e incorporando la dependencia de la velocidad de deformación para permitir su utilización en el ámbito dinámico. El modelo es estrictamente local y no requiere de remallado ni conocer previamente la trayectoria de la fisura. Este modelo constitutivo ha sido utilizado para simular dos campañas experimentales, probando la hipótesis de que el fallo de elementos de hormigón ante explosiones está gobernado por el comportamiento a tracción, siendo de especial relevancia el ablandamiento del hormigón. Concrete is nowadays one of the most widely used building materials because of its good mechanical properties, moldability and production economy, among other advantages. As it is known, it has high compressive and low tensile strengths and for this reason it is reinforced with steel bars to form reinforced concrete, a material that has become the most important constructive solution of our time. Despite being such a widely used material, there are some aspects of concrete performance that are not yet fully understood, as it is the case of its response to the effects of an explosion. This is a topic of particular relevance because the events, both intentional and accidental, in which a structure is subjected to an explosion are, unfortunately, relatively common. The loading of a structure due to an explosive event occurs due to the impact of the pressure shock wave generated in the detonation. The application of this load on the structure is very fast and of very short duration. Such actions are called impulsive loads, and can be up to four orders of magnitude faster than the dynamic loads imposed by an earthquake. Consequently, it is not surprising that their effects on structures and materials are very different than those that cause the loads usually considered in engineering. This thesis broadens the knowledge about the material behavior of concrete subjected to explosions. To that end, it is crucial to have experimental results of concrete structures subjected to explosions. These types of results are difficult to find in the scientific literature, as these tests have traditionally been carried out by armies of different countries and the results obtained are classified. Moreover, in experimental campaigns with explosives conducted by civil institutions the high cost of accessing explosives and the lack of proper test fields does not allow for the testing of a large number of samples. For this reason, the experimental scatter is usually not controlled. However, in reinforced concrete elements subjected to explosions the experimental dispersion is very pronounced. First, due to the heterogeneity of concrete, and secondly, because of the difficulty inherent to testing with explosions, for reasons such as difficulties in the boundary conditions, variability of the explosive, or even atmospheric changes. To overcome these drawbacks, in this thesis we have designed a novel device that allows for testing up to four concrete slabs under the same detonation, which apart from providing a statistically representative number of samples, represents a significant saving in costs. A number of 28 slabs were tested using this device. The slabs were both reinforced and plain concrete, and two different concrete mixes were used. Besides having experimental data, it is also important to have computational tools for the analysis and design of structures subjected to explosions. Despite the existence of several analytical methods, numerical simulation techniques nowadays represent the most advanced and versatile alternative for the assessment of structural elements subjected to impulsive loading. However, to obtain reliable results it is crucial to have material constitutive models that take into account the parameters that govern the behavior for the load case under study. In this regard it is noteworthy that most of the developed constitutive models for concrete at high strain rates arise from the ballistic field, dominated by large compressive stresses in the local environment of the area affected by the impact. In the case of concrete elements subjected to an explosion, the compressive stresses are much more moderate, while tensile stresses usually cause material failure. This thesis discusses the validity of some of the available models, confirming that the parameters governing the failure of reinforced concrete slabs subjected to blast are the tensile strength and softening behaviour after failure. Based on these results we have developed a constitutive model for concrete at high strain rates, which only takes into account the ultimate tensile strength. This model is based on the embedded Cohesive Crack Model with Strong Discontinuity Approach developed by Planas and Sancho, which has proved its ability in predicting the tensile fracture of plain concrete elements. The model has been modified for its implementation in the commercial explicit integration program LS-DYNA, using hexahedral finite elements and incorporating the dependence of the strain rate, to allow for its use in dynamic domain. The model is strictly local and does not require remeshing nor prior knowledge of the crack path. This constitutive model has been used to simulate two experimental campaigns, confirming the hypothesis that the failure of concrete elements subjected to explosions is governed by their tensile response, being of particular relevance the softening behavior of concrete.

The unstoppable rise of photovoltaic solar energy: PV vs. PV

Photovoltaic (PV) solar energy has been growing during the last decade an explosive rate. Last year (2011) the solar cell production amounted to more than 37 GW. It is the energy technology most installed nowadays. The power generated by the 37 GW is similar to the one generated by about 7 nuclear units of 1 GW each. The solar industry is already a huge industry dominated by Asian countries led by China. It is not anymore a promise. It is just a reality.

Güímar and La Orotava mega-landslides (Tenerife) and tsunamis deposits in Canary Islands

More than 20 mega-landslides have been described in the Canary Islands affecting the flanks of the volcanic edifices. Gliimar and La Orotava landslides, in Tenerife, are two exceptional cases due to their huge dimensions and outstanding geomorphological features. The estimated volume of these landslides exceed tens of cubic km. Tsunami deposits have been also identified in some of the islands of the archipelago probably associated to the large landslides of the islands flanks. An investigation has been carried out to explain the causes of these large instability processes and their failure mechanisms. One of the main aspects investigated was the geomechanical characteristics of the volcanic rock masses, specially the hyaloclastite rocks forming the substratum underlying the emerged volcanic building. The low strength and high deformability properties of these rocks have played a fundamental role on the stability of the island flanks. The results have shown the gravitational origin of these instability processes as the main failure mechanism. Volcanic eruptions or large earthquakes could be contributing factors to the instability, but according with the data obtained in Gliimar and La Orotava cases they are not necessary as triggering factors. As a result of the field work carried out in the frame of the project, three large tsunami deposits have been identified in the islands of Lanzarote, Tenerifc and Gran Canaria attributed to rnega-Iandslides, possibly related to Guimar and La Orotava. A Sumrnary of their main features is described.

Agaete revisited: new data on the Gran Canaria tsunamiites.

The tsunami deposits of the valley of Agaete (Pérez-Torrado et al., 2006), north-western Gran Canaria, attributed to the Guimar flank collapse in Tenerife, have been revisited and new data are presented here. Besides the occurrences reported by Pérez-Torrado et al. (2006) a new outcrop was found and named “La Ruina” (at 28º 05’ 47,41” N; 15º 41’ 52,04” W; 71 m asl). The above-mentioned authors suggested the possibility that more than one marine conglomerate deposit could be present in the outcrops of “Llanos de Turmán” and “Berrazales”. At “La Gasolinera” and “La Aldea 1” the conglomerates are formed by a single layer representing one depositional event; at “La Aldea 2”, the conglomerates are composed of two layers directly contacting with each other, but evidence of a time hiatus between them was not found. Although the hypothesis of stacking of two depositional units within the same episode versus deposition of two distinct layers in different time-moments is debatable at the present state of knowledge, the first possibility is favoured. The field evidence at “Llanos de Turman” and “Berrazales” unquestionably shows that terrestrial sediments (colluvia; paleosols) are present and separate two marine conglomerate deposits, indicating that at least two distinct tsunami inundations are needed to explain the stratigraphy. However, at the new “La Ruina” outcrop, besides the two deposits mentioned above, a third and older marine conglomerate was found, clearly separated in time from the ones cited above. The existence of marine conglomerates emplaced in different moments is evidenced by the occurrence of intercalated paleosols, colluvia and other subaerial materials, implying significant time intervals between the emplacement of marine conglomeratic layers. A number of gastropod operculae from the tsunamiites were sent for U-Th dating to try to further constrain the age span of these deposits. The field evidence presented above shows that the emplacement of the deposits is related to, at least, three tsunami events. The lateral correlation between different outcrops is difficult due to variable number of deposits in each outcrop, lateral discontinuity and variability, and to compositional and textural similarity between distinct tsunami sediments. The occurrence of three Pleistocene tsunami deposits in the same area points to a relatively high frequency of tsunamis (generated by landslides, surface rupturing earthquakes, fast entry of voluminous volcanic deposits into the sea or large submarine eruptions). It is possible that this recurrence of tsunami inundations may reflect multiple-phased landslides responsible for the mega-landslide scars prominent in the geomorphology of the neighbouring island of Tenerife. This is a contribution from project “Estabilidad de los edificios volcánicos en Canarias: análisis de los factores geológicos, geomecánicos y paleoclimáticos. Aplicación a los flancos N y S de la isla de Tenerife” financed by MCT, Spain.

Design of a training tool for improving the use of hand-held detectors in humanitarian demining

Purpose – The purpose of this paper is to introduce the design of a training tool intended to improve deminers' technique during close-in detection tasks. Design/methodology/approach – Following an introduction that highlights the impact of mines and improvised explosive devices (IEDs), and the importance of training for enhancing the safety and the efficiency of the deminers, this paper considers the utilization of a sensory tracking system to study the skill of the hand-held detector expert operators. With the compiled information, some critical performance variables can be extracted, assessed, and quantified, so that they can be used afterwards as reference values for the training task. In a second stage, the sensory tracking system is used for analysing the trainee skills. The experimentation phase aims to test the effectiveness of the elements that compose the sensory system to track the hand-held detector during the training sessions. Findings – The proposed training tool will be able to evaluate the deminers' efficiency during the scanning tasks and will provide important information for improving their competences. Originality/value – This paper highlights the need of introducing emerging technologies for enhancing the current training techniques for deminers and proposes a sensory tracking system that can be successfully utilised for evaluating trainees' performance with hand-held detectors.

Estudio sobre la medida de la velocidad de detonación

El presente proyecto trata de un análisis de las mediciones de la velocidad de detonación, obtenidas por diferentes métodos y dispositivos. Tiene como objetivo la inter-comparación de los resultados entre diferentes organismos para poder analizar las desviaciones e incertidumbres de las diferentes metodologías de medidas empleadas actualmente. Para ello, se realizaron medidas con dos tipos de explosivos por diferentes métodos y con dispositivos de medida distintos. A partir de esas mediciones y de las propiedades técnicas de los explosivos empleados, se determinó cuáles son los métodos más recomendables para utilizar en cada explosivo, y que dispositivos de medición de la velocidad de detonación más adecuado. ABSTRACT This project is an analysis of the velocity of detonation measurements, obtained by different kind of methods and devices. The aim of work is to compare the results between different laboratories and to be able to analyze the deviations and uncertainties the different measurement methodologies currently used. For that purpose, measurements were made with different explosives, and it was determined which methods and devices are the most suitable for each explosive. From these measurements and the technical features of each explosive used, we established what are the most suitable for each explosive use, and which is the most appropiate device to measure the detonation velocity.

Análisis de las voladuras realizadas en el centro minero Moró

En este proyecto se analizan seis voladuras realizadas en el Centro Minero Moró (CM Moró) perteneciente a la empresa SIBELCO HISPANIA S.A., situado en la localidad de San Juan de Moró (Castellón). Se analizan las principales diferencias de las voladuras, con respecto a las fases de avance donde se encuentran, el tipo de material volado, la presencia de agua en las mismas, variación de consumo de explosivo y toneladas de roca arrancada. Tomando como base las normas de SIBELCO HISPANIA S.A., el proyecto define la evolución histórica de la empresa, las normativas de seguridad y salud, el ciclo de explotación en el CM Moró, ya que el proceso de arranque tanto de estéril (arenisca y caliza) como de arcillas, se desarrolla por completo mediante voladuras y finalmente un descripción más extensa y concisa de las mismas. ABSTRACT The project presents a comparative study of six blasts realised in the Centro Minero Moró (CM Moró) owned by SIBELCO HISPANIA S.A., located in San Juan de Moró (Castellón). A series of calculations have been conducted and graphs created to observe the main differences between the blasts, with respect to the stage to which it has advanced, the presence of water therein, variation in explosive consumption and tonnes of extracted rocks. Taking the standards of SIBELCO HISPANIA S.A. as a basis, the project defines the historical evolution of the business, the health and safety regulations, the extraction cycle in the CM Moró, since both the sterile (sandstone and limestone) and the clay extraction process are fully achieved by blasts. Ultimately, the aim is to attain a more extensive description of the latter

Damping models in the truncated derivative nonlinear Schrödinger equation

Four-dimensional flow in the phase space of three amplitudes of circularly polarized Alfven waves and one relative phase, resulting from a resonant three-wave truncation of the derivative nonlinear Schrödinger equation, has been analyzed; wave 1 is linearly unstable with growth rate , and waves 2 and 3 are stable with damping 2 and 3, respectively. The dependence of gross dynamical features on the damping model as characterized by the relation between damping and wave-vector ratios, 2 /3, k2 /k3, and the polarization of the waves, is discussed; two damping models, Landau k and resistive k2, are studied in depth. Very complex dynamics, such as multiple blue sky catastrophes and chaotic attractors arising from Feigenbaum sequences, and explosive bifurcations involving Intermittency-I chaos, are shown to be associated with the existence and loss of stability of certain fixed point P of the flow. Independently of the damping model, P may only exist as against flow contraction just requiring.In the case of right-hand RH polarization, point P may exist for all models other than Landau damping; for the resistive model, P may exist for RH polarization only if 2+3/2.