Experimental investigation on box-wing configuration for UAS

The range for airframe configurations available for UAS is as diverse as those used for manned aircraft and more since the commercial risk in trying unorthodox solutions is less for the UAS manufacturer. This is principally because the UAS airframes are usually much smaller than the manned aircraft and operators are less likely to have a bias against unconventional configurations. One of these unconventional configurations is the box-wing, which is an unconventional solution for the design of the new UAS generation. The existence of two wings separated in different planes that are, however, significantly close together, means that the aerodynamic analysis by theoretical or computational methods is a difficult task, due to the considerable interference existing. Considering the fact that the flight of most UAS takes place at low Reynolds numbers, it is necessary to study the aerodynamics of the box wing configuration by testing different models in a wind tunnel to be able to obtain reasonable results. In the present work, the study is enhanced by varying not only the sweepback angles of the two wings, but also their position along the models’ fuselage. Certain models have shown being more efficient than others, pointing out that certain relative positions of wing exists that can improve the aerodynamics efficiency of the box wing configuration.

Experimental investigation of dynamic pressure loads during dam break

The objectives of this work are to revisit the experimental measurements on dam break flow over a dry horizontal bed and to provide a detailed insight into the dynamics of the dam break wave impacting a vertical wall downstream the dam, with emphasis on the pressure loads. The measured data are statistically analyzed and critically discussed. As a result, an extensive set of data for validation of computational tools is provided.

Experimental investigation of radio signal propagation in scientific facilities for telerobotic applications

Understanding the radio signal transmission characteristics in the environment where the telerobotic application is sought is a key part of achieving a reliable wireless communication link between a telerobot and a control station. In this paper, wireless communication requirements and a case study of a typical telerobotic application in an underground facility at CERN are presented. Then, the theoretical and experimental characteristics of radio propagation are investigated with respect to time, distance, location and surrounding objects. Based on analysis of the experimental findings, we show how a commercial wireless system, such as Wi-Fi, can be made suitable for a case study application at CERN.

Experimental and statistical investigation of canonical problems in sloshing

En hidrodinámica, el fenómeno de Sloshing se puede definir como el movimiento de la superficie libre de un fluido dentro de un contenedor sometido a fuerzas y perturbaciones externas. El fluido en cuestión experimenta violentos movimientos con importantes deformaciones de su superficie libre. La dinámica del fluido puede llegar a generar cargas hidrodinámicas considerables las cuales pueden afectar la integridad estructural y/o comprometer la estabilidad del vehículo que transporta dicho contenedor. El fenómeno de Sloshing ha sido extensivamente investigado matemática, numérica y experimentalmente, siendo el enfoque experimental el más usado debido a la complejidad del problema, para el cual los modelos matemáticos y de simulación son aun incapaces de predecir con suficiente rapidez y precisión las cargas debidas a dicho fenómeno. El flujo generado por el Sloshing usualmente se caracteriza por la presencia de un fluido multifase (gas-liquido) y turbulencia. Reducir al máximo posible la complejidad del fenómeno de Sloshing sin perder la esencia del problema es el principal reto de esta tesis doctoral, donde un trabajo experimental enfocado en casos canónicos de Sloshing es presentado y documentado con el objetivo de aumentar la comprensión de dicho fenómeno y por tanto intentar proveer información valiosa para validaciones de códigos numéricos. El fenómeno de Sloshing juega un papel importante en la industria del transporte marítimo de gas licuado (LNG). El mercado de LNG en los últimos años ha reportado un crecimiento hasta tres veces mayor al de los mercados de petróleo y gas convencionales. Ingenieros en laboratorios de investigación e ingenieros adscritos a la industria del LNG trabajan continuamente buscando soluciones económicas y seguras para contener, transferir y transportar grandes volúmenes de LNG. Los buques transportadores de LNG (LNGC) han pasado de ser unos pocos buques con capacidad de 75000 m3 hace unos treinta años, a una amplia flota con una capacidad de 140000 m3 actualmente. En creciente número, hoy día se construyen buques con capacidades que oscilan entre 175000 m3 y 250000 m3. Recientemente un nuevo concepto de buque LNG ha salido al mercado y se le conoce como FLNG. Un FLNG es un buque de gran valor añadido que solventa los problemas de extracción, licuefacción y almacenamiento del LNG, ya que cuenta con equipos de extracción y licuefacción a bordo, eliminando por tanto las tareas de transvase de las estaciones de licuefacción en tierra hacia los buques LNGC. EL LNG por tanto puede ser transferido directamente desde el FLNG hacia los buques LNGC en mar abierto. Niveles de llenado intermedios en combinación con oleaje durante las operaciones de trasvase inducen movimientos en los buques que generan por tanto el fenómeno de Sloshing dentro de los tanques de los FLNG y los LNGC. El trabajo de esta tesis doctoral lidia con algunos de los problemas del Sloshing desde un punto de vista experimental y estadístico, para ello una serie de tareas, descritas a continuación, se han llevado a cabo : 1. Un dispositivo experimental de Sloshing ha sido configurado. Dicho dispositivo ha permitido ensayar secciones rectangulares de tanques LNGC a escala con movimientos angulares de un grado de libertad. El dispositivo experimental ha sido instrumentado para realizar mediciones de movimiento, presiones, vibraciones y temperatura, así como la grabación de imágenes y videos. 2. Los impactos de olas generadas dentro de una sección rectangular de un LNGC sujeto a movimientos regulares forzados han sido estudiados mediante la caracterización del fenómeno desde un punto de vista estadístico enfocado en la repetitividad y la ergodicidad del problema. 3. El estudio de los impactos provocados por movimientos regulares ha sido extendido a un escenario más realístico mediante el uso de movimientos irregulares forzados. 4. El acoplamiento del Sloshing generado por el fluido en movimiento dentro del tanque LNGC y la disipación de la energía mecánica de un sistema no forzado de un grado de libertad (movimiento angular) sujeto a una excitación externa ha sido investigado. 5. En la última sección de esta tesis doctoral, la interacción entre el Sloshing generado dentro en una sección rectangular de un tanque LNGC sujeto a una excitación regular y un cuerpo elástico solidario al tanque ha sido estudiado. Dicho estudio corresponde a un problema de interacción fluido-estructura. Abstract In hydrodynamics, we refer to sloshing as the motion of liquids in containers subjected to external forces with large free-surface deformations. The liquid motion dynamics can generate loads which may affect the structural integrity of the container and the stability of the vehicle that carries such container. The prediction of these dynamic loads is a major challenge for engineers around the world working on the design of both the container and the vehicle. The sloshing phenomenon has been extensively investigated mathematically, numerically and experimentally. The latter has been the most fruitful so far, due to the complexity of the problem, for which the numerical and mathematical models are still incapable of accurately predicting the sloshing loads. The sloshing flows are usually characterised by the presence of multiphase interaction and turbulence. Reducing as much as possible the complexity of the sloshing problem without losing its essence is the main challenge of this phd thesis, where experimental work on selected canonical cases are presented and documented in order to better understand the phenomenon and to serve, in some cases, as an useful information for numerical validations. Liquid sloshing plays a key roll in the liquified natural gas (LNG) maritime transportation. The LNG market growth is more than three times the rated growth of the oil and traditional gas markets. Engineers working in research laboratories and companies are continuously looking for efficient and safe ways for containing, transferring and transporting the liquified gas. LNG carrying vessels (LNGC) have evolved from a few 75000 m3 vessels thirty years ago to a huge fleet of ships with a capacity of 140000 m3 nowadays and increasing number of 175000 m3 and 250000 m3 units. The concept of FLNG (Floating Liquified Natural Gas) has appeared recently. A FLNG unit is a high value-added vessel which can solve the problems of production, treatment, liquefaction and storage of the LNG because the vessel is equipped with a extraction and liquefaction facility. The LNG is transferred from the FLNG to the LNGC in open sea. The combination of partial fillings and wave induced motions may generate sloshing flows inside both the LNGC and the FLNG tanks. This work has dealt with sloshing problems from a experimental and statistical point of view. A series of tasks have been carried out: 1. A sloshing rig has been set up. It allows for testing tanks with one degree of freedom angular motion. The rig has been instrumented to measure motions, pressure and conduct video and image recording. 2. Regular motion impacts inside a rectangular section LNGC tank model have been studied, with forced motion tests, in order to characterise the phenomenon from a statistical point of view by assessing the repeatability and practical ergodicity of the problem. 3. The regular motion analysis has been extended to an irregular motion framework in order to reproduce more realistic scenarios. 4. The coupled motion of a single degree of freedom angular motion system excited by an external moment and affected by the fluid moment and the mechanical energy dissipation induced by sloshing inside the tank has been investigated. 5. The last task of the thesis has been to conduct an experimental investigation focused on the strong interaction between a sloshing flow in a rectangular section of a LNGC tank subjected to regular excitation and an elastic body clamped to the tank. It is thus a fluid structure interaction problem.

A wind tunnel two-dimensional parametric investigation of biplane configurations

This paper presents an experimental and systematic investigation about how geometric parameters on a biplane configuration have an influence on aerodynamic parameters. This experimental investigation has been developed in a two-dimensional approach. Theoretical studies about biplanes configurations have been developed in the past, but there is not enough information about experimental wind tunnel data at low Reynolds number. This two-dimensional study is a first step to further tridimensional investigations about the box wing configuration. The main objective of the study is to find the relationships between the geometrical parameters which present the best aerodynamic behavior: the highest lift, the lowest drag and the lowest slope of the pitching moment. A tridimensional wing-box model will be designed following the pattern of the two dimensional study conclusions. It will respond to the geometrical relationships that have been considered to show the better aerodynamic behavior. This box-wing model will be studied in the aim of comparing the advantages and disadvantages between this biplane configuration and the plane configuration, looking for implementing the box-wing in the UAV?s field. Although the box wing configuration has been used in a small number of existing UAV, prestigious researchers have found it as a field of high aerodynamic and structural potential.

Diseño de una Metodología de Política Pública de I+D+i para el Desarrollo de la Capacidad de la Innovación en el Sector PYMIS del estado Bolívar, Venezuela

El estado Bolívar con una superficie de 238.000 Km2 se encuentra ubicado al SE de Venezuela y su capital es Ciudad Bolívar. Ocupa el 26,24% de la superficie del territorio nacional. Ciudad Guayana es la principal región del desarrollo económico del estado siendo sede de las empresas básicas de los sectores siderúrgicos y del aluminio que se encargan de la extracción, procesamiento y transformación del mineral de hierro y de la transformación de la bauxita en aluminio primario. Además, cuenta con un gran potencial hidroeléctrico, garantizando el suministro de energía eléctrica para el funcionamiento de las empresas básicas, para el parque industrial de la región, así como para el desarrollo industrial, económico y social de la nación. Con relación al sector de la industria del mineral de hierro y del aluminio, las empresas destinan más del 60 por ciento de su producción al mercado internacional. A pesar de que el sector de las Pequeñas y Medianas Industrias (PYMIS) del estado Bolívar cuenta con un mercado cercano y seguro, no se le ha propiciado un desarrollo integral en términos de orientar sus esfuerzos en innovar en nuevos productos o mejoras de procesos. Debido a la falta del personal de investigación calificado, la escasa vinculación con centros de investigación, la baja inversión en investigación, desarrollo tecnológico e innovación (I+D+i), la ausencia de la aplicación de una política pública de I+D+i y la desarticulación de los miembros del Sistema Regional de Innovación (SRI), constituyen los principales obstáculos para generar bienes y servicios con un alto valor agregado. Esta situación desequilibra y hace ineficiente el funcionamiento del SRI. La baja capacidad de las PYMIS del estado Bolívar en I+D+i, es una situación que impide generar por si sola nuevos productos o procesos para satisfacer las demandas del mercado regional. Por lo tanto, se requiere de la intervención y participación activa de la institución gubernamental responsable del diseño y aplicación de una política pública de I+D+i para dinamizar la capacidad de innovación en las PYMIS, en su articulación y vinculación con los miembros del SRI. xiii El presente proyecto se planteó como objetivo diseñar una metodología de política pública de I+D+i para liderar, coordinar y direccionar el SRI del estado Bolívar, para el desarrollo de la capacidad de innovación en el sector industrial y específicamente en las PYMIS. La presente tesis representa una investigación no experimental de tipo proyectivo que analiza la situación actual del Sistema Regional de Innovación del estado Bolívar. El análisis de los resultados se ha dividido en tres fases. En la primera se realizan diagnósticos por medio de encuestas de las PYMIS en materia de I+D+i, de los centros y laboratorios de investigación pertenecientes a las universidades de la región en el área de Materiales y de los sectores financieros público y privado. En dichas encuestas se evalúa el nivel de integración con los entes gubernamentales que definen y administran la política pública de I+D+i. En la segunda fase, con el diagnóstico y procesamiento de los resultados de la primera fase, se procede a desarrollar un análisis de las fortalezas, oportunidades, debilidades y amenazas (FODA) del Sistema Regional de Innovación, permitiendo comprender la situación actual de la relación y vinculación de las PYMIS con los centros de investigación, instituciones financieras y entes gubernamentales. Con la problemática detectada, resultó necesario el diseño de estrategias y un modelo de gestión de política pública de I+D+i para la articulación de los miembros del SRI, para el apoyo de las PYMIS. En la tercera fase se diseña la metodología de política pública de I+D+i para fortalecer la innovación en las PYMIS. La metodología se representa a través de un modelo propuesto que se relaciona con las teorías de los procesos de innovación, con los modelos de sistemas de innovación y con las reflexiones y recomendaciones hechas por diferentes investigadores e instituciones de cooperación internacional referentes a la aplicación de políticas públicas de I+D+i para dinamizar la capacidad de innovación en el sector industrial. La metodología diseñada es comparada con diferentes modelos de aplicación de política pública de I+D+i. Cada modelo se representa en una figura y se analiza su xiv situación presente y la función que desempeña el ente gubernamental en la aplicación del enfoque de política pública de I+D+i. El diseño de la metodología de política pública de I+D+i propuesta aportará nuevos conocimientos y podrá ser aplicado para apoyar el progreso de la I+D+i en las PYMIS de la región, como caso de estudio, con el fin de impulsar una economía más competitiva y reducir el grado de dependencia tecnológica. La metodología una vez evaluada podrá ser empleada en el contexto de la gran industria y en otras regiones de Venezuela y además, puede aplicarse en otros países con características similares en su tejido industrial. En la tesis doctoral se concluye que el desarrollo de la capacidad de innovación en las PYMIS depende del diseño y aplicación de la política pública de I+D+i como elemento dinamizador y articulador del SRI del estado Bolívar. xv ABSTRACT The Bolivar state with an area of 238,000 km2 is located in the SE of Venezuela and its capital is Ciudad Bolivar. It occupies a surface which is 26.24% of the national territory. Ciudad Guayana is the main area of the state's economic development and the location of the corporate headquarters of the basic steel and aluminum sectors that are responsible for the extraction, processing and transformation of iron ore and bauxite processing for primary aluminum. It also has a great hydroelectric potential, ensuring the supply of electricity for the operation of enterprises, for the regional industrial park as well as for the industrial, economic and social development of the nation. With regard to the iron ore and aluminum industry, companies allocate more than 60 percent of their production to the international market. Although the sector of Small and Medium Industries (SMIs) of the Bolivar state has a secure market, it has not been led to an integral development in terms of targeting its efforts on innovating new products or improving processes. Due to the lack of qualified research staff, poor links with research centers, low investment in research, technological development and innovation (R & D & I), the absence of the implementation of a public policy for R & D & I and the dismantling of the members of the Regional Innovation System (RIS), are the main obstacles to generate goods and services with high added value. This situation makes the RIS unbalanced and inefficient. The low capacity of Bolivar state’s SMIs in R & D & I, is a situation that cannot generate by itself new products or processes to meet regional market demands. Therefore, it requires the active involvement and participation of the government institution responsible for the design and implementation of R & D & I public policy to boost the innovation capacity in SMIs, through the connection and integration with members of the RIS. This project is intended to design a methodology aimed at public policy for R & D & I to lead, coordinate and direct the RIS of Bolivar state, for the development of innovation capacity in the industrial sector and specifically in the SMIs. xvi This thesis is an experimental investigation of projective type which analyzes the current situation of the Regional Innovation System of the Bolivar state. The analysis of the results is divided into three phases. In the first one, a diagnosis is performed through surveys of SMIs in R & D & I centers and research laboratories belonging to the universities of the region in the area of materials and public and private financial sectors. In such surveys the level of integration with government agencies that define and manage the public policy of R & D & I is assessed. In the second phase, with the diagnosis and processing of the results of the first phase, we proceed to develop an analysis of the strengths, weaknesses, opportunities and threats (SWOT) of the Regional Innovation System, allowing the comprehension of the current status of the relationship of SMIs with research centers, financial institutions and government agencies. With the problems identified it was necessary to design strategies and a model of public policy management of R & D & I for the articulation of the members of the RIS, to support the SMIs. In the third phase a public policy methodology for R & D & I is designed in order to strengthen innovation in SMIs. The methodology is shown through a proposed model that relates to the theories of the innovation process, with models of innovation systems and with the discussions and recommendations made by different researchers and institutions of international cooperation concerning the implementation of policies public for R & D & I to boost innovation capacity in the industrial sector. The methodology designed is compared with different models of public policy implementation for R & D & I. Each model is represented in a figure and its current situation and the role of the government agency in the implementation of the public policy approach to R & D & I is analyzed. The design of the proposed public policy methodology for R & D & I will provide new knowledge and can be applied to support the progress of R & D & I in the region’s SMIs, as a case study, in order to boost a more competitive economy and reduce the degree of technological dependence. After being evaluated the methodology can be used in the context of big industry and in other regions of Venezuela and can also be applied in other countries with similar characteristics in their industrial structure. xvii The thesis concludes that the development of the innovation capacity in SMIs depends on the design and implementation of the public policy for R & D & I as a catalyst and coordination mechanism of the Regional Innovation System of the Bolivar state.

Seismic performance and damage evaluation of a reinforced concrete frame with hysteretic dampers through shake-table tests

Passive energy dissipation devices are increasingly implemented in frame structures to improve their performance under seismic loading. Most guidelines for designing this type of system retain the requirements applicable to frames without dampers, and this hinders taking full advantage of the benefits of implementing dampers. Further, assessing the extent of damage suffered by the frame and by the dampers for different levels of seismic hazard is of paramount importance in the framework of performance-based design. This paper presents an experimental investigation whose objectives are to provide empirical data on the response of reinforced concrete (RC) frames equipped with hysteretic dampers (dynamic response and damage) and to evaluate the need for the frame to form a strong column-weak beam mechanism and dissipate large amounts of plastic strain energy. To this end, shake-table tests were conducted on a 2/5-scale RC frame with hysteretic dampers. The frame was designed only for gravitational loads. The dampers provided lateral strength and stiffness, respectively, three and 12 times greater than those of the frame. The test structure was subjected to a sequence of seismic simulations that represented different levels of seismic hazard. The RC frame showed a performance level of "immediate occupancy", with maximum rotation demands below 20% of the ultimate capacity. The dampers dissipated most of the energy input by the earthquake. It is shown that combining hysteretic dampers with flexible reinforced concrete frames leads to structures with improved seismic performance and that requirements of conventional RC frames (without dampers) can be relieved.

Some examples of the simultaneous use of closed-form and numerical solutions in shell structural analysis

The computational advantages of the use of different approaches -numerical and analytical ones- to the analysis of different parts of the same shell structure are discussed. Examples of large size problems that can be reduced to those more suitable to be handled by a personal related axisyrometric finite elements, local unaxisymmetric shells, geometric quasi-regular shells, infinite elements and homogenization techniques are described

The folded plate model in structural analysis. Elastic, plastic and dynamic formulations for nonprismatic structures

A specific numerical procedure for the analysis of arbitrary nonprismatic folded plate structures is presented. An elastic model is studied and compared with a harmonic solution for a prismatic structure. An extension to the plastic analysis is developed, and the influence of the structural geometry and loading pattern is analyzed. Nonprismatic practical cases, with arbitrary geometry and loading are shown, as well in the elastic range as in the plastic one. Finally, a dynamic formulation is outlined

Comportamiento de pilares de hormigón armado confinados con materiales compuestos sometidos a compresión centrada

En la actualidad muchas estructuras de hormigón armado necesitan ser reforzadas debido a diversas razones: errores en el proyecto o construcción, deterioro debido a efectos ambientales, cambios de uso o mayores requerimientos en los códigos. Los materiales compuestos, también conocidos como polímeros reforzados con fibras (FRP), están constituidos por fibras continuas de gran resistencia y rigidez embebidas en un material polimérico. Los FRP se utilizan cada vez más en aplicaciones estructurales debido a sus excelentes propiedades (elevadas resistencia y rigidez específicas y resistencia a la corrosión). Una de las aplicaciones más atractivas es el refuerzo de pilares mediante confinamiento para incrementar su resistencia y ductilidad. El confinamiento puede conseguirse pegando capas de FRP envolviendo el pilar en la dirección de los cercos (con las fibras orientadas en dirección perpendicular al eje del elemento). Se han realizado numerosos estudios experimentales en probetas cilíndricas pequeñas confinadas con encamisados de FRP y sometidas a compresión axial, y se han propuesto varios modelos sobre el hormigón confinado con FRP. Es sabido que el confinamiento de pilares de sección no circular es menos eficiente. En una sección circular, el FRP ejerce una presión de confinamiento uniforme sobre todo el perímetro, mientras que en una sección rectangular la acción de confinamiento se concentra en las esquinas. Esta tesis presenta los resultados de una investigación experimental sobre el comportamiento de probetas de hormigón de sección cuadrada confinadas con FRP y sometidas a compresión centrada. Se realizaron un total de 42 ensayos investigándose el comportamiento en las direcciones axial y transversal. Las variables del estudio incluyen: la resistencia del hormigón, el tipo de fibras (vidrio o carbono), la cuantía de refuerzo y el radio de curvatura de las esquinas. Los resultados de los ensayos realizados muestran que el confinamiento con FRP puede mejorar considerablemente la resistencia y ductilidad de pilares de hormigón armado de sección cuadrada con las esquinas redondeadas. La mejora conseguida es mayor en los hormigones de baja resistencia que en los de resistencia media. La deformación de rotura de la camisa de FRP es menor que la que se obtiene en ensayos de tracción normalizados del laminado, y la eficiencia del confinamiento depende en gran medida del radio de redondeo de las esquinas. Los resultados se han comparado con los obtenidos según los modelos teóricos más aceptados. Hay dos parámetros críticos en el ajuste de los modelos: el factor de eficiencia de la deformación y el efecto de confinamiento en secciones no circulares. Nowadays, many existing RC structures are in need of repair and strengthening for several reasons: design or construction errors, deterioration caused by environmental effects, change in use of the structures or revisions of code requirements. Composite materials, also known as fibre reinforced polymers (FRP), are composed of high strength and stiffness continuous fibres embedded in a polymer material. FRP materials are being increasingly used in many structural applications due to their excellent properties (high strength- and stiffness-toweight ratio, good corrosion behaviour). One of the most attractive applications of FRP is the confinement of concrete columns to enhance both strength and ductility. Concrete confinement can be achieved by bonding layers of hoop FRP around the column (fibres oriented perpendicular to the longitudinal axis). Many experimental studies have been conducted on small-scale plain concrete specimens of circular cross-sections confined with FRP and subjected to pure axial compressive loading, and several design models have been proposed to describe the behaviour of FRP-confined concrete. It is widely accepted that the confinement of non-circular columns is less efficient than the confinement of circular columns. In a circular cross section, the jacket exerts a uniform confining pressure over the entire perimeter. In the case of a rectangular cross section, the confining action is mostly concentrated at the corners. This thesis presents the results of a comprehensive experimental investigation on the behaviour of axially loaded square concrete specimens confined with FRP. A total of 42 compression tests were conducted, and the behaviour of the specimens in the axial and transverse directions were investigated. The parameters considered in this study are: concrete strength, type of fibres (glass or carbon), amount of FRP reinforcement and corner radius of the cross section. The tests results indicate that FRP confinement can enhance considerably the compressive strength and ductility of RC square columns with rounded corners. The enhancement is more pronounced for low- than for normal-strength concrete. The rupture strain of the FRP jacket is lower than the ultimate strain obtained by standard tensile testing of the FRP material, and the confinement efficiency significantly depends on the corner radius. The confined concrete behaviour was predicted according to the more accepted theoretical models and compared with experimental results. There are two key parameters which critically influence the fitting of the models: the strain efficiency factor and the effect of confinement in non-circular sections.

Experimental and numerical investigation of effect of sawn timber dimensions in ultrasonic velocity measurements of Spanish softwoods

Ultrasonic sound velocity measurements with hand-held equipment remain due to their simplicity among the most used methods for non-destructive grading of sawn woods, yet a dedicated normalization effort with respect to strength classes for Spanish species is still required. As part of an ongoing project with the aim of definition of standard testing methods, the effect of the dimensions of commonly tested Scots pine (Pinus sylvestris L.) timbers and equipment testing frequency on ultrasonic velocity were investigated. A dedicated full-wave finite-difference time-domain software allowed simulation of pulse propagation through timbers of representative length and section combinations. Sound velocity measurements vL were performed along the grain with the indirect method at 22 kHz and 45 kHz for grids of measurement points at specific distances. For sample sections larger than the cross-sectional wavelength ?RT, the simulated sound velocity vL converges to vL = (CL/?)0.5. For smaller square sections the sound velocity drops down to vL = (EL/?)0.5, where CL, EL and ? are the stiffness, E-modul and density, respectively. The experiments confirm a linear regression between time of flight and measurement distance even at less than two wavelength menor que2?L distance, the fitted sound speed values increased by 15% between the two tested frequencies.

Flow around a hemisphere-cylinder at high angle of attack and low Reynolds number. Part I: Experimental and numerical investigation

Three-dimensional Direct Numerical Simulations combined with Particle Image Velocimetry experiments have been performed on a hemisphere-cylinder at Reynolds number 1000 and angle of attack 20◦. At these flow conditions, a pair of vortices, so-called “horn” vortices, are found to be associated with flow separation. In order to understand the highly complex phenomena associated with this fully threedimensional massively separated flow, different structural analysis techniques have been employed: Proper Orthogonal and Dynamic Mode Decompositions, POD and DMD, respectively, as well as criticalpoint theory. A single dominant frequency associated with the von Karman vortex shedding has been identified in both the experimental and the numerical results. POD and DMD modes associated with this frequency were recovered in the analysis. Flow separation was also found to be intrinsically linked to the observed modes. On the other hand, critical-point theory has been applied in order to highlight possible links of the topology patterns over the surface of the body with the computed modes. Critical points and separation lines on the body surface show in detail the presence of different flow patterns in the base flow: a three-dimensional separation bubble and two pairs of unsteady vortices systems, the horn vortices, mentioned before, and the so-called “leeward” vortices. The horn vortices emerge perpendicularly from the body surface at the separation region. On the other hand, the leeward vortices are originated downstream of the separation bubble, as a result of the boundary layer separation. The frequencies associated with these vortical structures have been quantified.