New version of a laboratory impact device for firmness sensing of fruits.

Results of previous studies conducted by different researchers have shown that impact techniques can be used to evaluate firmness (Delwiche et al., 1989; Delwiche et al.;1996; Jaren et al., 1992; Ruiz Altisent et al., 1996). To impact the fruit with a small spherical impactor of known mass and radius of curvature and measure the acceleration of the impactor is a technique described by Chen et al. (1985) and used by several researchers for sensing fruit firmness (Jaren et al., 1992; Correa et al.; 1992). The advantages of this method vs. a force sensor that measures the force as a function of time is that the measured impact-acceleration response is independent of the fruit mass and is less sensitive to the variation in the radius of curvature of the fruit (Chen et al., 1996). Ruiz Altisent et al. (1993) developed and used a 50 g impactor with a 19 mm diameter spherical tip, dropping from different height for fruits (apples, pears, avocados, melons, peaches ...). Another impact device for firmness sensing of fruits was developed by Chen and Ruiz Altisent (1996). They designed and fabricated an experimental low-mass impact sensor for high-speed sensing of fruit firmness. The impactor consisted of a semi-spherical impacting tip attached to the end (near the centre of percussion) of a pivoting arm. Impact is done by swinging the impactor to collide with the fruit. It has been implemented for on-line use. In both devices a small accelerometer is mounted behind the impacting tip. Lateral impactor and vertical impactor have been used in laboratory and the results from non-destructive impact tests have contributed to standardise methods to measure fruit firmness: Barreiro (1992) compared impact parameters and results of Magness-Taylor penetration tests for apples, pears, apricots [and peaches; Agulheiro (1994) studied the behaviour of the impact parameters during seven weeks of cold storage of two melon varieties; Ortiz (1998) used low energy impact and NIR procedures to segregate non crispy, non firm and soft peaches. Steinmetz (1996) compared various non-destructive firmness sensors, based on sound, impact and micro-deformation.

Low-injection behaviour of a solar cell with a metallic grating back-reflector

Recent studies have dealt with the possibility of increasing light absorption by using the so-called electric field enhancement taking place within the grooves of metallic gratings. In order to evaluate the potential improvements derived from the absorption increase, we employ a simplified model to analyze the low-injection behaviour of a solar cell with a metallic grating back-reflector.

A parametric, experimental analysis of conical vortices on curved roofs of low-rise buildings

Different methods to reduce the high suction caused by conical vortices have been reported in the literature: vertical parapets, either solid or porous, placed at the roof edges being the most analysed configuration. Another method for alleviating the high suction peaks due to conical vortices is the use of some non-standard parapet configuration like cantilever parapets. In this paper the influence of roof curvature on the conical vortex pattern appearing on a curved roof (Fig. 1) when subject to oblique winds is experimentally analysed by testing the mean pressure distribution on the curved roofs of low-rise building models in a wind tunnel. Also, the efficiency of cantilever parapets to reduce mean suction loads on curved roofs is experimentally checked. Very high suction loads have been measured on curved roofs, the magnitude of these high suction loads being significantly decreased when cantilever parapets are used. Thus, the suitability of these parapets to reduce wind pressure loads on curved roofs is demonstrated.

Short-term response of the Ca cycle of a montane forest in Ecuador to low experimental CaCl2 additions

The tropical montane forests of the E Andean cordillera in Ecuador receive episodic Sahara- dust inputs particularly increasing Ca deposition. We added CaCl2 to isolate the effect of Ca deposition by Sahara dust to tropical montane forest from the simultaneously occurring pH effect. We examined components of the Ca cycle at four control plots and four plots with added Ca (2 × 5 kg ha?1 Ca annually as CaCl2) in a random arrangement. Between August 2007 and December 2009 (four applications of Ca), we determined Ca concentrations and fluxes in litter leachate, mineral soil solution (0.15 and 0.30 m depths), throughfall, and fine litterfall and Al con- centrations and speciation in soil solutions. After 1 y of Ca addition, we assessed fine-root bio- mass, leaf area, and tree growth. Only < 3% of the applied Ca leached below the acid organic layer (pH 3.5?4.8). The added CaCl2 did not change electrical conductivity in the root zone after 2 y. In the second year of fertilization, Ca retention in the canopy of the Ca treatment tended to decrease relative to the control. After 2 y, 21% of the applied Ca was recycled to soil with throughfall and litterfall. One year after the first Ca addition, fine-root biomass had decreased significantly. Decreasing fine-root biomass might be attributed to a direct or an indirect beneficial effect of Ca on the soil decomposer community. Because of almost complete association of Al with dissolved organic matter and high free Ca2+ : Al3+ activity ratios in solution of all plots, Al toxicity was unlikely. We conclude that the added Ca was retained in the system and had benefi- cial effects on some plants.

Perfil de playas sustentadas : estudio hidrodinámico y experimental : directrices de diseño

Las playas sustentadas por medio de un pie sumergido son una atractiva alternativa de diseño de regeneración de playas especialmente cuando las condiciones física del emplazamiento o las características de la arena nativa y de préstamo producen perfiles de alimentación que no se intersectan. La observación y propuesta de este tipo de solución data de los años 1960’s, así como la experiencia internacional en la construcción de este tipo de playas. Sin embargo, a pesar de su utilización y los estudios en campo y laboratorio, no se dispone de criterios ingenieriles que apoyen el diseño de las mismas. Esta tesis consiste en un análisis experimental del perfil de playas sustentadas en un pie sumergido (o colgadas) que se concreta en una propuesta de directrices de diseño general que permiten estimar la ubicación y características geométricas del pie sumergido frente a un oleaje y material que constituye la playa determinados. En la tesis se describe el experimento bidimensional realizado en el modelo físico de fondo móvil, donde se combinan cinco tipos de oleaje con tres configuraciones del pie sumergido (“Sin estructura”, configuración baja o “Estructura 1” y configuración alta o “Estructura 2”), se presentan los resultados obtenidos y se realiza una discusión detallada de las implicaciones de los resultados desde el punto de vista hidrodinámico utilizando monomios adimensionales. Se ha realizado un análisis detallado del estado del arte sobre playas colgadas, presentando el concepto y las experiencias de realizaciones en distintos países. Se ha realizado una cuidadosa revisión de la literatura publicada sobre estudios experimentales de playas colgadas, modelos teóricos y otras cuestiones auxiliares, necesarias para la formulación de la metodología de la tesis. El estudio realizado se ha estructurado en dos fases. En la primera fase se ha realizado una experimentación en un modelo físico de fondo móvil construido en las instalaciones del Centro de Estudios de Puertos y Costas (CEPYC) del Centro de Estudios y Experimentación de Obras Públicas (CEDEX), consistente en un canal de 36 m de longitud, 3 m de anchura y 1.5 m de altura, provisto de un generador de oleaje de tipo pistón. Se ha diseñado una campaña de 15 ensayos, que se obtienen sometiendo a cinco tipos de oleaje tres configuraciones distintas de playa colgada. En los ensayos se ha medido el perfil de playa en distintos instantes hasta llegar al equilibrio, determinando a partir de esos datos el retroceso de la línea de costa y el volumen de sedimentos perdido. El tiempo total efectivo de ensayo asciende a casi 650 horas, y el número de perfiles de evolución de playa obtenidos totaliza 229. En la segunda fase se ha abordado el análisis de los resultados obtenidos con la finalidad de comprender el fenómeno, identificar las variables de las que depende y proponer unas directrices ingenieriles de diseño. Se ha estudiado el efecto de la altura de ola, del periodo del oleaje, del francobordo adimensional y del parámetro de Dean, constatándose la dificultad de comprensión del funcionamiento de estas obras ya que pueden ser beneficiosas, perjudiciales o inocuas según los casos. También se ha estudiado la respuesta del perfil de playa en función de otros monomios adimensionales, tales como el número de Reynolds o el de Froude. En el análisis se ha elegido el monomio “plunger” como el más significativo, encontrando relaciones de éste con el peralte de oleaje, la anchura de coronación adimensional, la altura del pie de playa adimensional y el parámetro de Dean. Finalmente, se propone un método de diseño de cuatro pasos que permite realizar un primer encaje del diseño funcional de la playa sustentada frente a un oleaje de características determinadas. Las contribuciones más significativas desde el punto de vista científico son: - La obtención del juego de resultados experimentales. - La caracterización del comportamiento de las playas sustentadas. - Las relaciones propuestas entre el monomio plunger y las distintas variables explicativas seleccionadas, que permiten predecir el comportamiento de la obra. - El método de diseño propuesto, en cuatro pasos, para este tipo de esquemas de defensa de costas. Perched beaches are an attractive beach nourishment design alternative especially when either the site conditions or the characteristics of both the native and the borrow sand lead to a non-intersecting profile The observation and suggestion of the use of this type of coastal defence scheme dates back to the 1960’s, as well as the international experience in the construction of this type of beaches. However, in spite of its use and the field and laboratory studies performed to-date, no design engineering guidance is available to support its design. This dissertation is based on the experimental work performed on a movable bed physical model and the use of dimensionless parameters in analyzing the results to provide general functional design guidance that allow the designer, at a particular stretch of coast - to estimate the location and geometric characteristics of the submerged sill as well as to estimate the suitable sand size to be used in the nourishment. This dissertation consists on an experimental analysis of perched beaches by means of a submerged sill, leading to the proposal of general design guidance that allows to estimate the location and geometric characteristics of the submerged sill when facing a wave condition and for a given beach material. The experimental work performed on a bi-dimensional movable bed physical model, where five types of wave conditions are combined with three configurations of the submerged sill (“No structure”, low structure or “Structure 1”, and high structure or “Structure 2”) is described, results are presented, and a detailed discussion of the results - from the hydrodynamic point of view – of the implications of the results by using dimensionless parameters is carried out. A detailed state of the art analysis about perched beaches has been performed, presenting the “perched beach concept” and the case studies of different countries. Besides, a careful revision of the literature about experimental studies on perched beaches, theoretical models, and other topics deemed necessary to formulate the methodology of this work has been completed. The study has been divided into two phases. Within the first phase, experiments on a movable-bed physical model have been developed. The physical model has been built in the Centro de Estudios de Puertos y Costas (CEPYC) facilities, Centro de Estudios y Experimentación de Obras Públicas (CEDEX). The wave flume is 36 m long, 3 m wide and 1.5 m high, and has a piston-type regular wave generator available. The test plan consisted of 15 tests resulting from five wave conditions attacking three different configurations of the perched beach. During the development of the tests, the beach profile has been surveyed at different intervals until equilibrium has been reached according to these measurements. Retreat of the shoreline and relative loss of sediment in volume have been obtained from the measurements. The total effective test time reaches nearly 650 hours, whereas the total number of beach evolution profiles measured amounts to 229. On the second phase, attention is focused on the analysis of results with the aim of understanding the phenomenon, identifying the governing variables and proposing engineering design guidelines. The effect of the wave height, the wave period, the dimensionless freeboard and of the Dean parameter have been analyzed. It has been pointed out the difficulty in understanding the way perched beaches work since they turned out to be beneficial, neutral or harmful according to wave conditions and structure configuration. Besides, the beach profile response as a function of other dimensionless parameters, such as Reynolds number or Froude number, has been studied. In this analysis, the “plunger” parameter has been selected as the most representative, and relationships between the plunger parameter and the wave steepness, the dimensionless crest width, the dimensionless crest height, and the Dean parameter have been identified. Finally, an engineering 4-step design method has been proposed, that allows for the preliminary functional design of the perched beach for a given wave condition. The most relevant contributions from the scientific point of view have been: - The acquisition of a consistent set of experimental results. - The characterization of the behavior of perched beaches. - The proposed relationships between the plunger parameter and the different explanatory variables selected, that allow for the prediction of the beach behavior. - The proposed design method, four-step method, for this type of coastal defense schemes.

Flow around a hemisphere-cylinder at high angle of attack and low Reynolds number. Part I: Experimental and numerical investigation

Three-dimensional Direct Numerical Simulations combined with Particle Image Velocimetry experiments have been performed on a hemisphere-cylinder at Reynolds number 1000 and angle of attack 20◦. At these flow conditions, a pair of vortices, so-called “horn” vortices, are found to be associated with flow separation. In order to understand the highly complex phenomena associated with this fully threedimensional massively separated flow, different structural analysis techniques have been employed: Proper Orthogonal and Dynamic Mode Decompositions, POD and DMD, respectively, as well as criticalpoint theory. A single dominant frequency associated with the von Karman vortex shedding has been identified in both the experimental and the numerical results. POD and DMD modes associated with this frequency were recovered in the analysis. Flow separation was also found to be intrinsically linked to the observed modes. On the other hand, critical-point theory has been applied in order to highlight possible links of the topology patterns over the surface of the body with the computed modes. Critical points and separation lines on the body surface show in detail the presence of different flow patterns in the base flow: a three-dimensional separation bubble and two pairs of unsteady vortices systems, the horn vortices, mentioned before, and the so-called “leeward” vortices. The horn vortices emerge perpendicularly from the body surface at the separation region. On the other hand, the leeward vortices are originated downstream of the separation bubble, as a result of the boundary layer separation. The frequencies associated with these vortical structures have been quantified.