Residuos orgánicos como fuentes de fósforo

En este trabajo, se han llevado a cabo distintos experimentos en laboratorio, con el objetivo de estudiar el efecto de la aplicación de residuos orgánicos como fuentes de P en las pérdidas de este elemento, que se producen en suelo, tanto por escorrentía superficial como por lixiviación. El interés por evaluar las pérdidas de P se debe a la necesidad de conocer mejor los factores que influyen en los procesos de pérdidas de este elemento y así, poder reducir los problemas de eutrofización de aguas, tanto superficiales como subterráneas, provocadas por un exceso de este nutriente, junto con otros como el nitrógeno. Los trabajos experimentales que se han llevado a cabo se detallan a continuación: Se ha realizado el estudio de las formas de P contenidas en una serie de 14 residuos orgánicos, de distinto origen y tratamiento (compost, lodos, purines y digestato), comparando la información aportada por tres protocolos de fraccionamientos de P diferentes, seleccionados entre los principales métodos utilizados: protocolo de fraccionamiento de Ruttemberg (1992), protocolo de Normas, medidas y ensayos (Ruban et al., 2001a) y protocolo de Huang et al. (2008). Todos los métodos de fraccionamiento empleados aportaron información útil para conocer las formas de P de los residuos, a pesar de que alguno de ellos fue descrito para sedimentos o suelos. Sin embargo, resulta difícil comparar los resultados entre unos y otros, ya que cada uno emplea extractantes y tiempos de ensayos diferentes. Las cantidades de P total determinadas por cada método mantienen una relación lineal, aunque el método SMT, por ser más directo, obtiene las cantidades más elevadas para todos los residuos. Los métodos secuenciales (métodos de Huang y Ruttemberg), a pesar de ser más largos y tediosos, aportan información más detallada de la disponibilidad de las formas de P, y con ello, permiten obtener una mejor estimación de las pérdidas potenciales de este elemento tras su aplicación en suelo. Se han encontrado relaciones positivas entre las fracciones determinadas por estos dos métodos. Así mismo, se encuentra una correlación entre las formas solubles de P y la concentración de los iones [Ca + Fe + Al] de los residuos, útiles como indicadores de la disponibilidad de este elemento. Sin embargo, el protocolo SMT, no obtiene información de la solubilidad o disponibilidad de las formas de P contenidas, ni las formas determinadas mantienen relaciones directas con las de los otros métodos, con excepción del P total. Para el estudio del comportamiento de los residuos aplicados en suelos, se pusieron a punto sistemas de lluvia simulada, con el objetivo de caracterizar las pérdidas de P en la escorrentía superficial generada. Por otra parte, se emplearon columnas de suelos enmendados con residuos orgánicos, para el estudio de las pérdidas de P por lixiviación. Los ensayos de simulación de lluvia se llevaron a cabo de acuerdo al “National Phosphorus Research proyect“ (2001), que consigue simular eventos sucesivos de lluvia en unas condiciones semejantes a la realidad, empleando cajas llenas de suelo del horizonte superficial, con residuos aplicados tanto superficialmente como mediante mezcla con el propio suelo. Los ensayos se realizaron con seis residuos de diferente naturaleza y sometidos a distintos tratamientos. Se encontraron diferencias significativas en las pérdidas de las formas de P analizadas, tanto disueltas como particuladas, en las aguas de escorrentía generadas. En general, las pérdidas en el primer evento de lluvia tras la aplicación de los residuos fueron mayores a las generadas en el segundo evento, predominando las formas de P particuladas respecto a las disueltas en ambos. Se encontró una relación positiva entre las pérdidas de P en las aguas de escorrentía generadas en cada ensayo, con los contenidos de P soluble en agua y fácilmente disponible de los residuos empleados, determinados por los protocolos de fraccionamientos secuenciales. Además, se emplearon los modelos matemáticos desarrollados por Vadas et al. (2005, 2007), de evaluación de las pérdidas de P por escorrentía para fertilizantes y estiércoles. La predicción de estos modelos no se cumple en el caso de todos los residuos. Las distintas propiedades físicas de los residuos pueden afectar a las diferencias entre las pérdidas experimentales y las esperadas. Los ensayos de simulación del proceso de lixiviación se llevaron a cabo en columnas de percolación, con suelos enmendados con residuos orgánicos, de acuerdo a la norma “CEN/TS 14405–2004: Caracterización de los residuos – Test de comportamiento de lixiviación – Test de flujo ascendente”. Las pérdidas de P por procesos de lixiviación de agua, han sido despreciadas durante mucho tiempo respecto a las pérdidas por escorrentía. Sin embargo, se ha demostrado que deben tenerse en consideración, principalmente en algunos tipos de suelos o zonas cercanas a acuíferos. Se utilizaron tres suelos de distinta procedencia para los ensayos, de manera que se pudo estudiar la influencia del tipo de suelo en las pérdidas de P para cada tipo de residuo (purín, compost, digestato y lodo de EDAR). Los índices de adsorción de P determinados para cada suelo permiten evaluar aquellos que presentarán más riesgo de producir pérdidas de este elemento al aplicarse fuentes externas de P, encontrando una relación positiva entre ambos. Las pérdidas de P en los lixiviados varían en función tanto del residuo como del suelo empleado. Para el compost, el purín y el lodo, se encontró una relación entre las pérdidas generadas en el agua lixiviada de las columnas y las formas de P soluble contenidas en los residuos. Sin embargo, en el caso del digestato, no existía esta correlación. Las pérdidas para este residuo fueron en todos los casos menores a las estimadas, considerando las formas de P contenido. El estudio de la mojabilidad, propiedad física del residuo que evalúa la capacidad de interacción residuo-agua, permitió explicar el comportamiento anómalo de este residuo, con una mayor resistencia a que el agua entrara en su estructura y por tanto, una mayor dificultad de solubilizar el P contenido en el propio residuo, que en el caso de otros residuos. En general, podemos considerar que el estudio de las formas de P más disponibles o solubles en agua, aporta información útil de las pérdidas potenciales de P. Sin embargo, es necesario estudiar las propiedades físicas de los residuos orgánicos aplicados y la capacidad de adsorción de P de los suelos, para estimar las pérdidas de P y con ello, colaborar a controlar los procesos de eutrofización en aguas. ABSTRACT This dissertation explores the effect of organic wastes application as sources of P in losses of this element that occur by both surface runoff and leaching in soil. To do so, diverse laboratory experiments are conducted and presented here. Evaluating P losses is necessary to better understand the factors that influence the processes behind the loss of this element. Reducing P losses reduces eutrophication problems of both surface water and groundwater caused by an excess of this nutrient, along with other as nitrogen. Details of the experiments are presented below: The first experiment studies the forms of P contained in a series of 14 organic wastes of different origin and treatment (compost, sludge, slurry and digestate), comparing the information provided by three methods of P fractionation. The methods selected were: Ruttemberg protocol (1992); Standards, Measurements and Testing protocol (Ruban et al., 2001a); and Huang protocol (Huang et al., 2008). All fractionation methods employed successfully contribute to our knowledge of P forms in wastes, even though one of them was originally described for sediments or soils information. However, it is difficult to compare results among each other, as each protocol employs different extractants and time in the trials. Total amounts of P obtained by each method show a linear relationship, although the SMT method, which is more direct, obtains the highest amounts for all residues. Sequential methods (Huang and Ruttemberg’s protocols), despite being longer and more tedious, provide more detailed information on the availability of the forms of P. Therefore, allow the estimation of the potential losses of P after application in soil. Furthermore, positive relationships have been found among fractions obtained by these methods. Positive relationship has been found also among soluble forms of P and the concentration of ions Fe + Ca + Al, which is useful as an indicator of the availability of this element. However, the SMT protocol does not collect information about solubility or availability of forms of P contained; neither do certain forms maintain direct relations with the forms from other methods, with the exception of total P methods. To study the behavior of wastes applied to soils two experiments were conducted. Simulated rain systems were prepared to characterize P losses in the surface runoff generated. In addition, columns of soils amended with organic waste were developed for the study of P leaching losses. Simulated rain systems were carried out according to the ’National Phosphorus Research Project’ (2001), which manages to simulate successive rainfall events in conditions resembling reality. The experiment uses boxes filled with soil from the surface horizon amended with residues, both superficially and by mixing with the soil. Tests were conducted with six residues of different type and subjected to diverse treatments. Findings show significant differences in losses of the P forms analyzed in the generated runoff water, in both solution and particulate forms. In general, losses in the first rainfall event after application of waste were higher than the losses generated in the second event, predominating particulate forms of P over dissolved forms in both events. In all trials, a positive relationship was found between various P forms determined by sequential fractionation protocols (water soluble P and readily available P forms) and P losses in runoff. Furthermore, results from Vadas´s mathematical models (Vadas et al., 2005; 2007) to assess P losses by runoff fertilizers and manures indicate that the prediction of this model is not fulfilled in the case of all residues. The diverse physical properties of wastes may affect the differences between experimental and expected losses. Finally, leaching simulation processes were carried out in percolation columns, filled with soils amended with organic wastes, following the ‘CEN/TS 14405-2004 standard: Characterization of waste - Leaching behavior test - Test Flow ascending ’. P losses by leaching have been neglected for a long time with respect to runoff losses. However, findings corroborate previous studies showing that these P losses have to be taken into account, especially in certain types of soils and in zones near aquifers. To study the influence of soil type on P losses, experiments were carried out with three different soils and for each type of waste (manure, compost, digestate and sludge WWTP). Each soil’s P adsorption rates allow assessing which soils imply a higher risk of P losses when external sources of P are applied. P losses in leachate vary according to the type of soil employed and according to the specific residue. In the case of compost, manure and sludge, there is a relationship between leaching losses and residues’ soluble forms of P. The exception being the digestate, where there was no such correlation. Digestate P losses by leaching were lower than expected in all cases considering the forms of P contained. Moreover, examining digestate wettability -- that is, the physical property of the residue that assesses the capacity of waste-water interaction -- allowed explaining the anomalous behavior of this residue. Digestate has a high resistance to water entering its structure and thus higher difficulty to solubilize the P contained. Overall, studying the more available or soluble P forms provides useful information about the potential loss of P. However, this dissertation shows that it is necessary to examine the physical properties of organic residues applied as well as the P adsorption capacity of soils to estimate P losses, and thus to control eutrophication in water.

Modelling agro-forestry scenarios for ammonia abatement in the landscape

Ammonia emissions from livestock production can have negative impacts on nearby protected sites and ecosystems that are sensitive to eutrophication and acidification. Trees are effective scavengers of both gaseous and particulate pollutants from the atmosphere making tree belts potentially effective landscape features to support strategies aiming to reduce ammonia impacts. This research used the MODDAS-THETIS a coupled turbulence and deposition turbulence model, to examine the relationships between tree canopy structure and ammonia capture for three source types?animal housing, slurry lagoon, and livestock under a tree canopy. By altering the canopy length, leaf area index, leaf area density, and height of the canopy in the model the capture efficiencies varied substantially. A maximum of 27% of the emitted ammonia was captured by tree canopy for the animal housing source, for the slurry lagoon the maximum was 19%, while the livestock under trees attained a maximum of 60% recapture. Using agro-forestry systems of differing tree structures near ?hot spots? of ammonia in the landscape could provide an effective abatement option for the livestock industry that complements existing source reduction measures.

Estudio de la influencia de la relación C/N en la desnitrificación y metanogénesis de aguas residuales en un reactor anaeróbico de lecho fluidizado inverso

La nitrificación-desnitrificación es el proceso biológico tradicional para la remoción de nitrógeno de las aguas residuales (Ruiz G. et al., 2006a), siendo fundamental ya que contribuye a controlar la eutroficación de los cuerpos receptores. Debido al deterioro que sobre la disponibilidad de los recursos han ejercido las actividades antropogénicas, es necesario orientar el tratamiento de las aguas residuales hacia tecnologías que ofrezcan el mayor grado de sustentabilidad, planteando innovaciones en el tratamiento. El presente proyecto de tesis doctoral versa sobre el estudio de la influencia de la relación C/N en la desnitrificación y metanogénesis de aguas residuales urbanas en un reactor anaeróbico de lecho fluidizado inverso (RLFI). Previamente a la realización de las pruebas experimentales de variación de la relación C/N, se llevó a cabo la etapa de arranque del RLFI la cual se inició en modo batch, favoreciendo la formación y adhesión de biopelícula al medio de soporte utilizado (Extendosphere). Después, sobrevino la operación en modo continuo desde una carga volumétrica aplicada (CVA) de 0.5 g DQOs/L⋅d hasta alcanzar 4 g DQOs/L⋅d, carga volumétrica a la cual se logró la plena estabilización del reactor, siendo la alta variabilidad de la concentración de DQOs en el agua residual urbana de alimentación, la principal problemática que ocasionó retrasos en la estabilidad del reactor. A una CVA de 4 g DQOs/L⋅d en estado estacionario, el valor mínimo de eficiencia de remoción de DQOs fue del 32.36% y el máximo de 66.99%. En estas condiciones el porcentaje de metano presente en el biogás producido tuvo un valor medio de 85.57 ± 2.93%, siendo un valor alto comparado con otros porcentajes de metano encontrados en la digestión anaerobia de aguas residuales urbanas. El YCH4 tuvo un valor medio de 0.316 ± 0.110 LCH4/g DQOrem⋅día. Los porcentajes de metanización variaron en el rango de 20.50 a 100%, registrándose un valor medio de 73.42 ± 25.63%. La considerable variabilidad en el porcentaje de metanización se debió principalmente a que se presentaron eventos de lavado de soporte colonizado, lo cual propició que las actividades metabólicas fueran orientadas hacia formación de biopelícula (anabolismo) en vez de estar dirigidas hacia producción de metano (catabolismo). En relación a los ensayos con variación de la relación C/N, se manejaron relaciones DQOs/N-NO3 en el rango de 1.65 a 21.1 g DQOs/g N-NO3. La tasa de remoción anaerobia de DQOs se incrementó con la concentración de sustrato en una relación casi lineal, ajustándose a una cinética de primer orden, lo que regularmente se presenta a concentraciones bajas de sustrato. La eficiencia del proceso de desnitrificación fue por lo regular alta, incrementándose ligeramente con la concentración de DQOs en el influente, con valores en el rango de 73.8 a 99.1%. Por otra parte, la tasa de remoción por metanogénesis se incrementó con la concentración relativa de sustrato (es decir, a mayores relaciones DQOs/N-NO3), siendo más sensitiva la metanogénesis a la concentración relativa de sustrato que la desnitrificación. Conforme aumentó la relación DQOs/N-NO3, la desnitrificación, de ser la ruta metabólica principal de utilización de la materia orgánica (comparada con la metanización), empezó a combinarse con la metanización. De manera evidente, a las relaciones DQOs/N-NO3 probadas, se manifestaron más las actividades desnitrificantes, quedando reflejadas por el alto porcentaje de utilización de la DQOs removida hacia la desnitrificación. La relación experimental DQOs/N-NO3 a la cual se pudiera haber cumplido con el requerimiento de materia orgánica (en términos de DQOs) para la desnitrificación de nitratos en las aguas residuales urbanas tratadas resultó aproximadamente ser igual a 7.1 g DQOs/g N-NO3. A una CVA de 4 g DQOs/L⋅d, se obtuvo un diámetro promedio máximo de soporte colonizado igual a 266.106 ± 69.279 μm aunque, hay que indicarlo, se presentaron fluctuaciones, las cuales se reflejaron también en el espesor de la biopelícula, el cual tuvo un valor máximo de 50.099 μm y un valor promedio de 37.294 ± 11.199 μm. Estas fluctuaciones pudieron deberse a la existencia de corrientes preferenciales dentro del reactor, las cuales no permitieron un acceso equitativo del sustrato a todo el lecho. Nitrification-denitrification is the traditional biological process for nitrogen removal from wastewaters (Ruiz G. et al., 2006a), being fundamental since it contributes to control the eutrophication of the receiving waters. Due to the deterioration that on the availability of the aquatic resources the anthropogenic activities have exerted, it is necessary to orient the treatment of wastewaters towards technologies that offer the greater degree of sustainability, raising innovations in the treatment. This work studied the influence of C/N ratio on denitrification and methanogenesis of urban wastewaters in an inverse fluidized bed reactor (IFBR). Previously to the accomplishment of the experimental tests with variation of C/N ratio, the start up of the IFBR was carried out in batch way, encouraging the formation and adhesion of biofilm to Extendosphere, which it was used as support. The operation in continuous way carried out from an organic loading rate (OLR) of 0.5 g CODs/L ∙ d to 4 g CODs/L ∙ d, when the steady-state was reached. The high variability of the CODs of the urban wastewaters caused delays in the stability of the reactor. Once stationary state was reached, the removal efficiency of CODs ranged from 32.36 to 66.99% to 4 g CODs/L ∙ d. In these conditions the percentage of methane in produced biogas had an average value of 85.57 ± 2.93%, being a high value compared with other studies treating anaerobically urban wastewaters. The YCH4 had an average value of 0.316 ± 0.110 LCH4/g CODrem ∙ d. The percentage of methanisation ranged from 20.50 to 100%, with an average value of 73.42 ± 25.63%. The considerable variability in the methanisation percentage occurred mainly due events of wash-out of colonized support, which caused that the metabolic activities were oriented towards formation of biofilm (anabolism) instead of methane production (catabolism). Concerning the tests with variation of C/N ratio, CODs/NO3-N ratios from 1.65 to 21.1 g CODs/g NO3-N were proved. The CODs anaerobic removal rate increased with the substrate concentration in an almost linear relation, adjusting to a kinetic of first order, which regularly appears to low concentrations of substrate. Efficiency of the denitrification process was regularly high, and it increased slightly with the CODs concentration in the influent, ranging from 73.8 to 99.1%. On the other hand, the CODs removal rate by methanogenesis increased with the substrate relative concentration (e.g., to greater CODs/NO3-N ratios), being more sensitive the methanogenesis to the substrate relative concentration that the denitrification. When the CODs/NO3-N ratio increased, the denitrification, of being the main metabolic route of use of the organic matter (compared with the methanogenesis), began to be combined with the methanogenesis. Definitively, to the proven CODs/NO3-N ratios the denitrification processes were more pronounced, being reflected by the high percentage of use of the removed CODs towards denitrification. The experimental CODs/NO3-N ratio to which it was possible to have been fulfilled the requirement of organic matter (in terms of CODs) for the denitrification of nitrates in urban wastewaters turned out to be approximately 7.1 g CODs/g NO3-N. It was obtained a maximum average diameter of colonized support of 266.106 ± 69.279 μm to 4 g CODs/L ∙ d, although it is necessary to indicate that appeared fluctuations in the thickness of biofilm, which had a maximum value of 50.099 μm and an average value of 37.294 ± 11.199 μm. These fluctuations could be due to the existence of preferential currents within the reactor, which did not allow an equitable access of the substrate to all the bed.

Life cycle assessment of concentrated solar power (CSP) and the influence of hybridising with natural gas

Purpose Concentrating Solar Power (CSP) plants based on parabolic troughs utilize auxiliary fuels (usually natural gas) to facilitate start-up operations, avoid freezing of HTF and increase power output. This practice has a significant effect on the environmental performance of the technology. The aim of this paper is to quantify the sustainability of CSP and to analyse how this is affected by hybridisation with different natural gas (NG) inputs. Methods A complete Life Cycle (LC) inventory was gathered for a commercial wet-cooled 50 MWe CSP plant based on parabolic troughs. A sensitivity analysis was conducted to evaluate the environmental performance of the plant operating with different NG inputs (between 0 and 35% of gross electricity generation). ReCiPe Europe (H) was used as LCA methodology. CML 2 baseline 2000 World and ReCiPe Europe E were used for comparative purposes. Cumulative Energy Demands (CED) and Energy Payback Times (EPT) were also determined for each scenario. Results and discussion Operation of CSP using solar energy only produced the following environmental profile: climate change 26.6 kg CO2 eq/KWh, human toxicity 13.1 kg 1,4-DB eq/KWh, marine ecotoxicity 276 g 1,4-DB eq/KWh, natural land transformation 0.005 m2/KWh, eutrophication 10.1 g P eq/KWh, acidification 166 g SO2 eq/KWh. Most of these impacts are associated with extraction of raw materials and manufacturing of plant components. The utilization NG transformed the environmental profile of the technology, placing increasing weight on impacts related to its operation and maintenance. Significantly higher impacts were observed on categories like climate change (311 kg CO2 eq/MWh when using 35 % NG), natural land transformation, terrestrial acidification and fossil depletion. Despite its fossil nature, the use of NG had a beneficial effect on other impact categories (human and marine toxicity, freshwater eutrophication and natural land transformation) due to the higher electricity output achieved. The overall environmental performance of CSP significantly deteriorated with the use of NG (single score 3.52 pt in solar only operation compared to 36.1 pt when using 35 % NG). Other sustainability parameters like EPT and CED also increased substantially as a result of higher NG inputs. Quasilinear second-degree polynomial relationships were calculated between various environmental performance parameters and NG contributions. Conclusions Energy input from auxiliary NG determines the environmental profile of the CSP plant. Aggregated analysis shows a deleterious effect on the overall environmental performance of the technology as a result of NG utilization. This is due primarily to higher impacts on environmental categories like climate change, natural land transformation, fossil fuel depletion and terrestrial acidification. NG may be used in a more sustainable and cost-effective manner in combined cycle power plants, which achieve higher energy conversion efficiencies.

Environmental analysis of a Concentrated Solar Power (CSP) plant hybridised with different fossil and renewable fuels

The environmental performance of a 50 MW parabolic trough Concentrated Solar Power (CSP) plant hybridised with different fuels was determined using a Life Cycle Assessment methodology. Six different scenarios were investigated, half of which involved hybridisation with fossil fuels (natural gas, coal and fuel oil), and the other three involved hybridisation with renewable fuels (wheat straw, wood pellets and biogas). Each scenario was compared to a solar-only operation. Nine different environmental categories as well as the Cumulative Energy Demand and the Energy Payback Time (EPT) were evaluated using Simapro software for 1 MWh of electricity produced. The results indicate a worse environmental performance for a CSP plant producing 12% of the electricity from fuel than in a solar-only operation for every indicator, except for the eutrophication and toxicity categories, whose results for the natural gas scenario are slightly better. In the climate change category, the results ranged between 26.9 and 187 kg CO2 eq/MWh, where a solar-only operation had the best results and coal hybridisation had the worst. Considering a weighted single score indicator, the environmental impact of the renewable fuels scenarios is approximately half of those considered in fossil fuels, with the straw scenario showing the best results, and the coal scenario the worstones. EPT for solar-only mode is 1.44 years, while hybridisation scenarios EPT vary in a range of 1.72 -1.83 years for straw and pellets respectively. The fuels with more embodied energy are biomethane and wood pellets.

Hybridizing concentrated solar power (CSP) with biogas and biomethane as an alternative to natural gas: Analysis of environmental performance using LCA

Concentrating Solar Power (CSP) plants typically incorporate one or various auxiliary boilers operating in parallel to the solar field to facilitate start up operations, provide system stability, avoid freezing of heat transfer fluid (HTF) and increase generation capacity. The environmental performance of these plants is highly influenced by the energy input and the type of auxiliary fuel, which in most cases is natural gas (NG). Replacing the NG with biogas or biomethane (BM) in commercial CSP installations is being considered as a means to produce electricity that is fully renewable and free from fossil inputs. Despite their renewable nature, the use of these biofuels also generates environmental impacts that need to be adequately identified and quantified. This paper investigates the environmental performance of a commercial wet-cooled parabolic trough 50 MWe CSP plant in Spain operating according to two strategies: solar-only, with minimum technically viable energy non-solar contribution; and hybrid operation, where 12 % of the electricity derives from auxiliary fuels (as permitted by Spanish legislation). The analysis was based on standard Life Cycle Assessment (LCA) methodology (ISO 14040-14040). The technical viability and the environmental profile of operating the CSP plant with different auxiliary fuels was evaluated, including: NG; biogas from an adjacent plant; and BM withdrawn from the gas network. The effect of using different substrates (biowaste, sewage sludge, grass and a mix of biowaste with animal manure) for the production of the biofuels was also investigated. The results showed that NG is responsible for most of the environmental damage associated with the operation of the plant in hybrid mode. Replacing NG with biogas resulted in a significant improvement of the environmental performance of the installation, primarily due to reduced impact in the following categories: natural land transformation, depletion of fossil resources, and climate change. However, despite the renewable nature of the biofuels, other environmental categories like human toxicity, eutrophication, acidification and marine ecotoxicity scored higher when using biogas and BM.

Eliminación de nutrientes mediante el empleo de cultivos hidropónicos

La presente investigación se presenta como una alternativa para la reducción de la contaminación por nutrientes que produce el vertido de aguas residuales provenientes de núcleos urbanos que acaban en lagos, lagunas o embalses acelerando los procesos de eutrofización de los mismos. El objetivo de esta tesis es analizar la reducción de nutrientes, fundamentalmente nitrógeno, fósforo y potasio, del agua residual doméstica sometida a tratamiento a través de cultivos hidropónicos en un determinado periodo de tiempo, observando a su vez la evolución del cultivo seleccionado. El sistema se diseñó para funcionar en circuito cerrado con el agua residual circulando por entre las raíces de los vegetales estudiados. El cultivo seleccionado fue el “kenaf”, aunque después de mucho tiempo dedicado a la obtención de semillas de “kenaf “por diferentes proveedores, se decidió comenzar un primer ensayo utilizando plantas de aloe vera durante un periodo de un mes de verano. Se procedió a la colocación de plantas en un tubo conteniendo agua residual de una fosa séptica domiciliaria. La reducción de la DBO5 y la DQO fue notable aunque los resultados de la variación de nitratos y fosfatos no fueron concluyentes. Las altas temperaturas alcanzada en esas fechas por el agua circulante, finalmente imposibilitó la continuación del ensayo. Si bien esta primera puesta en marcha no resultó como se esperaba, aportó numerosa información para modificar el planteo del estudio, la forma de llevarlo a cabo y la puesta a punto de la propia instalación. El segundo ensayo se llevó a cabo en otoño con plantas de kenaf obtenidas del ensayo previo en suelo en una parcela piloto en los llanos de Villamartín, en la provincia de Cádiz. Antes de incorporar el agua al sistema hidropónico se analizaron todos los parámetros requeridos por la normativa española del agua para determinar su clasificación como agua residual doméstica. Luego se le dio seguimiento a la variación de los nutrientes, nitrógeno, fósforo y potasio a lo largo de varias semanas para evaluar la efectividad del tratamiento. Las plantas de kenaf continuaron su desarrollo utilizando las sustancias disueltas en el agua residual como única fuente de nutrientes disponible. This research is presented as an alternative to reduce the pollution that wastewater discharges from towns generate when they end in lakes, ponds and reservoirs, by accelerating the eutrophication processes. The objective of this thesis is to analyze the reduction of nutrients, mainly nitrogen, phosphorus and potassium, of domestic wastewater treated through hydroponics crops in a given period of time, noting at the same time the evolution of the selected crop. The system was designed to operate in closed circuit with the wastewater circulating through the roots of the studied plants. The selected crop was "kenaf", although after much time spent in obtaining seeds of "kenaf"by different vendors and the impossibility of achieving its germination; it was decided to start a first test using Aloe Vera plants for a period of one month in the summer. The plants were introduced in the holes of a tube containing septic wastewater. The BOD5 and COD reduction was remarkable though the results of the variation in nitrates and phosphates were inconclusive. High temperatures achieved in those dates by circulating water, eventually precluded the continuation of the test. Although this first implementation was not running as expected, it provided information to modify the proposal of the study, the way to carry it out and the development of the installation itself. The second test was conducted in autumn with kenaf plants obtained from the previous test in a pilot plant in the flatness of Villamartín, province of Cádiz. Before adding the water to the hydroponic system all the parameters required by the Spanish water regulations were analyzed to determine their classification as domestic waste water. Then, the variation of nutrients, nitrogen, phosphorus and potassium was tracking over several weeks to evaluate the effectiveness of the treatment. Kenaf plants continued its development using the substances dissolved in wastewater as sole source of nutrients available.