Power system stability of a small sized isolated network supplied by a combined wind-pumped storage generation system: a case study in the Canary Islands

Massive integration of renewable energy sources in electrical power systems of remote islands is a subject of current interest. The increasing cost of fossil fuels, transport costs to isolated sites and environmental concerns constitute a serious drawback to the use of conventional fossil fuel plants. In a weak electrical grid, as it is typical on an island, if a large amount of conventional generation is substituted by renewable energy sources, power system safety and stability can be compromised, in the case of large grid disturbances. In this work, a model for transient stability analysis of an isolated electrical grid exclusively fed from a combination of renewable energy sources has been studied. This new generation model will be installed in El Hierro Island, in Spain. Additionally, an operation strategy to coordinate the generation units (wind, hydro) is also established. Attention is given to the assessment of inertial energy and reactive current to guarantee power system stability against large disturbances. The effectiveness of the proposed strategy is shown by means of simulation results.

Validation Study of the Use of Matlab/Simulink Synchronous-Machine Block for Accurate Power-Plant Stability Studies

This paper presents results of the validity study of the use of MATLAB/Simulink synchronous-machine block for power-system stability studies. Firstly, the waveforms of the theoretical synchronous-generator short-circuit currents are described. Thereafter, the comparison between the currents obtained through the simulation model in the sudden short-circuit test, are compared to the theoretical ones. Finally, the factory tests of two commercial generating units are compared to the response of the synchronous generator simulation block during sudden short-circuit, set with the same real data, with satisfactory results. This results show the validity of the use of this generator block for power plant simulation.

Performance metrics for small-signal stability assessment of DC-distributed power-system-architecture comparisons

The objective of this paper is to provide performance metrics for small-signal stability assessment of a given system architecture. The stability margins are stated utilizing a concept of maximum peak criteria (MPC) derived from the behavior of an impedance-based sensitivity function. For each minor-loop gain defined at every system interface, a single number to state the robustness of stability is provided based on the computed maximum value of the corresponding sensitivity function. In order to compare various power-architecture solutions in terms of stability, a parameter providing an overall measure of the whole system stability is required. The selected figure of merit is geometric average of each maximum peak value within the system. It provides a meaningful metrics for system comparisons: the best system in terms of robust stability is the one that minimizes this index. In addition, the largest peak value within the system interfaces is given thus detecting the weakest point of the system in terms of robustness.

Simplified small-signal stability analysis for optimized power system architecture

The optimization of power architectures is a complex problem due to the plethora of different ways to connect various system components. This issue has been addressed by developing a methodology to design and optimize power architectures in terms of the most fundamental system features: size, cost and efficiency. The process assumes various simplifications regarding the utilized DC/DC converter models in order to prevent the simulation time to become excessive and, therefore, stability is not considered. The objective of this paper is to present a simplified method to analyze small-signal stability of a system in order to integrate it into the optimization methodology. A black-box modeling approach, applicable to commercial converters with unknown topology and components, is based on frequency response measurements enabling the system small-signal stability assessment. The applicability of passivity-based stability criterion is assessed. The stability margins are stated utilizing a concept of maximum peak criteria derived from the behavior of the impedance-based sensitivity function that provides a single number to state the robustness of the stability of a well-defined minor-loop gain.

Systematic Method to Assess Small-Signal Stability of DC-Distributed Power-System-Architecture

The objective of this paper is to present a simplified method to analyze small-signal stability of a power system and provide performance metrics for stability assessment of a given power-system-architecture. The stability margins are stated utilizing a concept of maximum peak criteria (MPC), derived from the behavior of an impedance-based sensitivity function that provides a single number to state the robustness of the stability of a well-defined minor-loop gain. For each minor-loop gain, defined at every system interface, the robustness of the stability is provided as a maximum value of the corresponding sensitivity function. Typically power systems comprise of various interfaces and, therefore, in order to compare different architecture solutions in terms of stability, a single number providing an overall measure of the whole system stability is required. The selected figure of merit is geometric average of each maximum peak value within the system, combined with the worst case value of system interfaces.

Wind intermittency and CO2 reductions: the case of the spanish power system

Renewable energy sources are believed to reduce drastically greenhouse gas emissions that would otherwise be generated from fossil fuels used to generate electricity. This implies that a unit of renewable energy will replace a unit of fossil-fuel, with its CO2 emissions, on an equivalent basis (with no other effects on the grid). But, the fuel economy and emissions in the existing power systems are not proportional with the electricity production of intermittent sources due to cycling of the fossil fuel plants that make up the balance of the grid (i.e. changing the power output makes thermal units to operate less efficiently). This study focuses in the interactions between wind generation and thermal plants cycling, by establishing the levels of extra fuel use caused by decreased efficiencies of fossil back-up for wind electricity in Spain. We analyze the production of all thermal plants in 2011, studying different scenarios where wind penetration causes major deviations in programming, while we define a procedure for quantifying the carbon reductions by using emission factors and efficiency curves from the existing installations. The objectives are to discuss the real contributions of renewable energies to the environmental targets as well as suggest alternatives that would improve the reliability of future power systems.

Mission profile based optimization of a wearable power system

A Wearable Power System (WPS) is a portable power source utilized primarily to power the modern soldier’s electronic equipment. Such a system has to satisfy output power demands in the range of 20 W...200 W, specified as a 4-day mission profile and has a weight limit of 4 kg. To meet these demands, an optimization of a WPS, comprising an internal combustion (IC) engine, permanent magnetic three-phase electrical motor/generator, inverter, Li-batteries, DC-DC converters, and controller, is performed in this paper. The mechanical energy extracted from the fuel by IC engine is transferred to the generator that is used to recharge the battery and provide the power to the electrical output load. The main objectives are to select the engine, fuel and battery type, to match the weight of fuel and the number of battery cells, to find the optimal working point of engine and to minimize the system weight. To provide the second output voltage level of 14 VDC, a separate DC-DC converter is connected between the battery and the load, and optimized for the specified mission profile. A prototype of the WPS based on the optimization presented in the paper results in a total system weight of 3.9 kg and fulfils the mission profile.

Pre-investigation of water electrolysis for flexible energy storage at large scales: the case of the Spanish power system

This report analyzes the basis of hydrogen and power integration strategies, by using water electrolysis processes as a means of flexible energy storage at large scales.

Pre-investigation of water electrolysis for flexible energy storage at large scales: the case of the Spanish power system

This report analyzes the basis of hydrogen and power integration strategies, by using water electrolysis processes as a means of flexible energy storage at large scales. It is a prospective study, where the scope is to describe the characteristics of current power systems (like the generation technologies, load curves and grid constraints), and define future scenarios of hydrogen for balancing the electrical grids, considering the efficiency, economy and easiness of operations. We focus in the "Spanish case", which is a good example for planning the transition from a power system holding large reserve capacities, high penetration of renewable energies and limited interconnections, to a more sustainable energy system being capable to optimize the volumes, the regulation modes, the utilization ratios and the impacts of the installations. Thus, we explore a novel aspect of the "hydrogen economy" which is based in the potentials of existing power systems and the properties of hydrogen as energy carrier, by considering the electricity generation and demand globally and determining the optimal size and operation of the hydrogen production processes along the country; e.g. the cost production of hydrogen becomes viable for a base-load scenario with 58 TWh/year of power surplus at 0.025 V/kWh, and large number electrolyzer plants (50 MW) running in variable mode (1-12 kA/m2)

Stability and Transient Performance Assessment in a COTS-Module-Based Distributed DC/DC System

This paper introduces a method to analyze and predict stability and transient performance of a distributed system where COTS (Commercial-off-the-shelf) modules share an input filter. The presented procedure is based on the measured data from the input and output terminals of the power modules. The required information for the analysis is obtained by performing frequency response measurements for each converter. This attained data is utilized to compute special transfer functions, which partly determine the source and load interactions within the converters. The system level dynamic description is constructed based on the measured and computed transfer functions introducing cross-coupling mechanisms within the system. System stability can be studied based on the well-known impedance- related minor-loop gain at an arbitrary interface within the system.

Methodology for Dynamic Stability and Robustness Analysis of Commercial-Power-Module-Based DC-Distributed Systems

El propósito de esta tesis es presentar una metodología para realizar análisis de la dinámica en pequeña señal y el comportamiento de sistemas de alimentación distribuidos de corriente continua (CC), formados por módulos comerciales. Para ello se hace uso de un método sencillo que indica los márgenes de estabilidad menos conservadores posibles mediante un solo número. Este índice es calculado en cada una de las interfaces que componen el sistema y puede usarse para obtener un índice global que indica la estabilidad del sistema global. De esta manera se posibilita la comparación de sistemas de alimentación distribuidos en términos de robustez. La interconexión de convertidores CC-CC entre ellos y con los filtros EMI necesarios puede originar interacciones no deseadas que dan lugar a la degradación del comportamiento de los convertidores, haciendo el sistema más propenso a inestabilidades. Esta diferencia en el comportamiento se debe a interacciones entre las impedancias de los diversos elementos del sistema. En la mayoría de los casos, los sistemas de alimentación distribuida están formados por módulos comerciales cuya estructura interna es desconocida. Por ello los análisis presentados en esta tesis se basan en medidas de la respuesta en frecuencia del convertidor que pueden realizarse desde los terminales de entrada y salida del mismo. Utilizando las medidas de las impedancias de entrada y salida de los elementos del sistema, se puede construir una función de sensibilidad que proporciona los márgenes de estabilidad de las diferentes interfaces. En esta tesis se utiliza el concepto del valor máximo de la función de sensibilidad (MPC por sus siglas en inglés) para indicar los márgenes de estabilidad como un único número. Una vez que la estabilidad de todas las interfaces del sistema se han evaluado individualmente, los índices obtenidos pueden combinarse para obtener un único número con el que comparar la estabilidad de diferentes sistemas. Igualmente se han analizado las posibles interacciones en la entrada y la salida de los convertidores CC-CC, obteniéndose expresiones analíticas con las que describir en detalle los acoplamientos generados en el sistema. Los estudios analíticos realizados se han validado experimentalmente a lo largo de la tesis. El análisis presentado en esta tesis se culmina con la obtención de un índice que condensa los márgenes de estabilidad menos conservativos. También se demuestra que la robustez del sistema está asegurada si las impedancias utilizadas en la función de sensibilidad se obtienen justamente en la entrada o la salida del subsistema que está siendo analizado. Por otra parte, la tesis presenta un conjunto de parámetros internos asimilados a impedancias, junto con sus expresiones analíticas, que permiten una explicación detallada de las interacciones en el sistema. Dichas expresiones analíticas pueden obtenerse bien mediante las funciones de transferencia analíticas si se conoce la estructura interna, o utilizando medidas en frecuencia o identificación de las mismas a través de la respuesta temporal del convertidor. De acuerdo a las metodologías presentadas en esta tesis se puede predecir la estabilidad y el comportamiento de sistemas compuestos básicamente por convertidores CC-CC y filtros, cuya estructura interna es desconocida. La predicción se basa en un índice que condensa la información de los márgenes de estabilidad y que permite la obtención de un indicador de la estabilidad global de todo el sistema, permitiendo la comparación de la estabilidad de diferentes arquitecturas de sistemas de alimentación distribuidos. ABSTRACT The purpose of this thesis is to present dynamic small-signal stability and performance analysis methodology for dc-distributed systems consisting of commercial power modules. Furthermore, the objective is to introduce simple method to state the least conservative margins for robust stability as a single number. In addition, an index characterizing the overall system stability is obtained, based on which different dc-distributed systems can be compared in terms of robustness. The interconnected systems are prone to impedance-based interactions which might lead to transient-performance degradation or even instability. These systems typically are constructed using commercial converters with unknown internal structure. Therefore, the analysis presented throughout this thesis is based on frequency responses measurable from the input and output terminals. The stability margins are stated utilizing a concept of maximum peak criteria, derived from the behavior of impedance-based sensitivity function that provides a single number to state robust stability. Using this concept, the stability information at every system interface is combined to a meaningful number to state the average robustness of the system. In addition, theoretical formulas are extracted to assess source and load side interactions in order to describe detailed couplings within the system. The presented theoretical analysis methodologies are experimentally validated throughout the thesis. In this thesis, according to the presented analysis, the least conservative stability margins are provided as a single number guaranteeing robustness. It is also shown that within the interconnected system the robust stability is ensured only if the impedance-based minor-loop gain is determined at the very input or output of each subsystem. Moreover, a complete set of impedance-type internal parameters as well as the formulas according to which the interaction sensitivity can be fully explained and analyzed, is provided. The given formulation can be utilized equally either based on measured frequency responses, time-domain identified internal parameters or extracted analytic transfer functions. Based on the analysis methodologies presented in this thesis, the stability and performance of interconnected systems consisting of converters with unknown internal structure, can be predicted. Moreover, the provided concept to assess the least conservative stability margins enables to obtain an index to state the overall robust stability of distributed power architecture and thus to compare different systems in terms of stability.

Optimal design of AC EMI filters with damping networks and effect on the systems power factor

The cutoff frequencies of an EMI filter are normally given by the noise attenuation requirements the filter has to fulfill. In order to select the component values of the filter elements, i.e. inductances and capacitances, an additional design criterium is needed. In this paper the effect of the EMI filter input and output impedances are considered. The input impedance influences the filters effect on the system displacement power factor and the output impedance plays a key role in the system stability. The effect of filter element values, the number of filter stages as well as additional damping networks are considered and a design procedure is provided. For this analysis a two-port description of the input filters employing ABCD-parameters is used.

Potencial de la producción de bioelectricidad de las Comarcas Agrarias de la Comunidad de Madrid en base a centeno y triticale

En el presente trabajo se estudia la producción potencial de biomasa procedente de los cultivos de centeno y triticale en las seis comarcas agrarias de la Comunidad de Madrid (CM) y la posibilidad de su aplicación a la producción de bioelectricidad en cada una de ellas. En primer lugar se realiza un estudio bibliográfico de la situación actual de la bioelectricidad. Uno de los principales datos a tener en cuenta es que en el PER 2011- 2020 se estima que el total de potencia eléctrica instalada a partir de biomasa en España en el año 2020 sea de 1.350 MW, unas dos veces y media la existente a finales de 2010. Además, se comenta el estado de la incentivación del uso de biomasa de cultivos energéticos para producción de electricidad, la cual se regula actualmente según el Real Decreto-ley 9/2013, de 12 de Julio, por el que se adoptaron medidas urgentes para garantizar la estabilidad financiera del sistema eléctrico, y se consideran los criterios de sostenibilidad en el uso de biocombustibles sólidos. Se realiza una caracterización de las seis comarcas agrarias que forman la Comunidad Autónoma de Madrid: Área Metropolitana, Campiña, Guadarrama, Lozoya- Somosierra, Sur-Occidental y Vegas, la cual consta de dos partes: una descripción de la climatología y otra de la distribución de la superficie dedicada a barbecho y cultivos herbáceos. Se hace una recopilación bibliográfica de los modelos de simulación más representativos de crecimiento de los cultivos (CERES y Cereal YES), así como de ensayos realizados con los cultivos de centeno y triticale para la producción de biomasa y de estudios efectuados mediante herramientas GIS y técnicas de análisis multicriterio para la ubicación de centrales de bioelectricidad y el estudio de la logística de la biomasa. Se propone un modelo de simulación de la productividad de biomasa de centeno y de triticale para la CM, que resulta de la combinación de un modelo de producción de grano en base a datos climatológicos y a la relación biomasa/grano media de ambos cultivos obtenida en una experiencia previa. Los modelos obtenidos responden a las siguientes ecuaciones (siendo TN = temperatura media normalizada a 9,9 ºC y PN = precipitación acumulada normalizada a 496,7 mm): - Producción biomasa centeno (t m.s./ha) = 2,785 * [1,078 * ln(TN + 2*PN) + 2,3256] - Producción biomasa triticale (t m.s./ha) = 2,595 * [2,4495 * ln(TN + 2*PN) + 2,6103] Posteriormente, aplicando los modelos desarrollados, se cuantifica el potencial de producción de biomasa de centeno y triticale en las distintas comarcas agrarias de la CM en cada uno de los escenarios establecidos, que se consideran según el uso de la superficie de barbecho de secano disponible (25%, 50%, 75% y 100%). Las producciones potenciales de biomasa, que se podrían alcanzar en la CM utilizando el 100% de la superficie de barbecho de secano, en base a los cultivos de centeno y triticale, se estimaron en 169.710,72 - 149.811,59 - 140.217,54 - 101.583,01 - 26.961,88 y 1.886,40 t anuales para las comarcas de Campiña - Vegas, Sur - Occidental - Área Metropolitana - Lozoya-Somosierra y Guadarrama, respectivamente. Se realiza un análisis multicriterio basado en la programación de compromiso para definir las comarcas agrarias con mejores características para la ubicación de centrales de bioelectricidad en base a los criterios de potencial de biomasa, infraestructura eléctrica, red de carreteras, espacios protegidos y superficie de núcleos urbanos. Al efectuar el análisis multicriterio, se obtiene la siguiente ordenación jerárquica en base a los criterios establecidos: Campiña, Sur Occidental, Vegas, Área Metropolitana, Lozoya-Somosierra y Guadarrama. Mediante la utilización de técnicas GIS se estudia la localización más conveniente de una central de bioelectricidad de 2,2 MW en cada una de las comarcas agrarias y según el uso de la superficie de barbecho de secano disponible (25%, 50%, 75% y 100%), siempre que exista potencial suficiente. Para el caso de la biomasa de centeno y de triticale en base seca se considera un PCI de 3500 kcal/kg, por lo que se necesitarán como mínimo 17.298,28 toneladas para satisfacer las necesidades de cada una de las centrales de 2,2 MW. Se analiza el potencial máximo de bioelectricidad en cada una de las comarcas agrarias en base a los cultivos de centeno y triticale como productores de biomasa. Según se considere el 25% o el 100% del barbecho de secano para producción de biomasa, la potencia máxima de bioelectricidad que se podría instalar en cada una de las comarcas agrarias variaría entre 5,4 y 21,58 MW en la comarca Campiña, entre 4,76 y 19,05 MW en la comarca Vegas, entre 4,46 y 17,83 MW en la comarca Sur Occidental, entre 3,23 y 12,92 MW en la comarca Área Metropolitana, entre 0,86 y 3,43 MW en la comarca Lozoya Somosierra y entre 0,06 y 0,24 MW en la comarca Guadarrama. La potencia total que se podría instalar en la CM a partir de la biomasa de centeno y triticale podría variar entre 18,76 y 75,06 MW según que se utilice el 25% o el 100% de las tierras de barbecho de secano para su cultivo. ABSTRACT In this work is studied the potential biomass production from rye and triticale crops in the six Madrid Community (MC) agricultural regions and the possibility of its application to the bioelectricity production in each of them. First is performed a bibliographical study of the current situation of bioelectricity. One of the main elements to be considered is that in the PER 2011-2020 is estimated that the total installed electric power from biomass in Spain in 2020 was 1.350 MW, about two and a half times as at end 2010. Also is discussed the status of enhancing the use of biomass energy crops for electricity production, which is currently regulated according to the Real Decreto-ley 9/2013, of July 12, by which urgent measures were adopted to ensure financial stability of the electrical system, and there are considered the sustainability criteria in the use of solid biofuels. A characterization of the six Madrid Community agricultural regions is carried out: Area Metropolitana, Campiña, Guadarrama, Lozoya-Somosierra, Sur-Occidental and Vegas, which consists of two parts: a description of the climatology and another about the distribution of the area under fallow and arable crops. It makes a bibliographic compilation of the most representative crop growth simulation models (CERES and Cereal YES), as well as trials carried out with rye and triticale crops for biomass production and studies conducted by GIS tools and techniques multicriteria analysis for the location of bioelectricity centrals and the study of the logistics of biomass. Is proposed a biomass productivity simulation model for rye and triticale for MC that results from the combination of grain production model based on climatological data and the average relative biomass/grain of both crops obtained in a prior experience. The models obtained correspond to the following equations (where TN = normalized average temperature and PN = normalized accumulated precipitation): - Production rye biomass (t d.m./ha) = 2.785 * [1.078 * ln (TN + 2*PN) + 2.3256] - Production triticale biomass (t d.m./ha) = 2,595 * [2.4495 * ln (TN + 2*PN) + 2.6103] Subsequently, applying the developed models, the biomass potential of the MC agricultural regions is quantified in each of the scenarios established, which are considered as the use of dry fallow area available (25%, 50%, 75 % and 100%). The potential biomass production that can be achieved within the MC using 100% of the rainfed fallow area based on rye and triticale crops, were estimated at 169.710,72 - 149.811,59 - 140.217,54 - 101.583,01 - 26.961,88 and 1.886,40 t annual for the regions of Campiña, Vegas, Sur Occidental, Area Metropolitana, Lozoya- Somosierra and Guadarrama, respectively. A multicriteria analysis is performed, based on compromise programming to define the agricultural regions with better features for the location of bioelectricity centrals, on the basis of biomass potential, electrical infrastructure, road network, protected areas and urban area criteria. Upon multicriteria analysis, is obtained the following hierarchical order based on criteria: Campiña, Sur Occidental, Vegas, Area Metropolitana, Lozoya-Somosierra and Guadarrama. Likewise, through the use of GIS techniques, the most suitable location for a 2,2 MW bioelectricity plant is studied in each of the agricultural regions and according to the use of dry fallow area available (25%, 50% , 75% and 100%), if there is sufficient potential. In the case of biomass rye and triticale dry basis is considered a PCI of 3500 kcal/kg, so it will take at least 17,298.28 t to satisfy the needs of each plant. Is analyzed the maximum bioelectricity potential on each of the agricultural regions on the basis of the rye and triticale crops as biomass producers. As deemed 25% or 100% dry fallow for biomass, the maximum bioelectricity potential varies between 5,4 and 21,58 MW in the Campiña region, between 4,76 and 19,05 MW in the Vegas region, between 4,46 and 17,83 MW in the Sur Occidental region, between 3,23 and 12,92 MW in the Area Metropolitana region, between 0,86 and 3,43 MW in the Lozoya-Somosierra region and between 0,06 and 0,24 MW in the Guadarrama region. The total power that could be installed in the CM from rye and triticale biomass could vary between 18.76 and 75.06 MW if is used the 25% or 100% of fallow land for rainfed crop.

Development and experimental evaluation of a complete solar thermophotovoltaic system

We present a practical implementation of a solar thermophotovoltaic (TPV) system. The system presented in this paper comprises a sunlight concentrator system, a cylindrical cup-shaped absorber/emitter (made of tungsten coated with HfO2), and an hexagonal-shaped water-cooled TPV generator comprising 24 germanium TPV cells, which is surrounding the cylindrical absorber/emitter. This paper focuses on the development of shingled TPV cell arrays, the characterization of the sunlight concentrator system, the estimation of the temperature achieved by the cylindrical emitters operated under concentrated sunlight, and the evaluation of the full system performance under real outdoor irradiance conditions. From the system characterization, we have measured short-circuit current densities up to 0.95 A/cm2, electric power densities of 67 mW/cm2, and a global conversion efficiency of about 0.8%. To our knowledge, this is the first overall solar-to-electricity efficiency reported for a complete solar thermophotovoltaic system. The very low efficiency is mainly due to the overheating of the cells (up to 120 °C) and to the high optical concentrator losses, which prevent the achievement of the optimum emitter temperature. The loss analysis shows that by improving both aspects, efficiencies above 5% could be achievable in the very short term and efficiencies above 10% could be achieved with further improvements.

Interleaved multi-cell isolated three-phase PWM rectifier system for aircraft applications

Recently there has been an important increase in electric equipment, as well as, electric power demand in aircrafts applications. This prompts to the necessity of efficient, reliable, and low-weight converters, especially rectifiers from 115VAC to 270VDC because these voltages are used in power distribution. In order to obtain a high efficiency, in aircraft application where the derating in semiconductors is high, normally several semiconductors are used in parallel to decrease the conduction losses. However, this is in conflict with high reliability. To match both goals of high efficiency and reliability, this work proposes an interleaved multi-cell rectifier system, employing several converter cells in parallel instead of parallel-connected semiconductors. In this work a 10kW multi-cell isolated rectifier system has been designed where each cell is composed of a buck type rectifier and a full bridge DC-DC converter. The implemented system exhibits 91% of efficiency, high power density (10kW/10kg), low THD (2.5%), and n−1 fault tolerance which complies, with military aircraft standards.