Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Driving assistance system applied in curves for real vehicles | Sistema de ayuda a la conducción en curvas para vehículos reales

Decreasing the accidents on highway and urban environments is the main motivation for the research and developing of driving assistance systems, also called ADAS (Advanced Driver Assistance Systems). In recent years, there are many applications of these systems in commercial vehicles: ABS systems, Cruise Control (CC), parking assistance and warning systems (including GPS), among others. However, the implementation of driving assistance systems on the steering wheel is more limited, because of their complexity and sensitivity. This paper is focused in the development, test and implementation of a driver assistance system for controlling the steering wheel in curve zones. This system is divided in two levels: an inner control loop which permits to execute the position and speed target, softening the action over the steering wheel, and a second control outer loop (controlling for fuzzy logic) that sends the reference to the inner loop according the environment and vehicle conditions. The tests have been done in different curves and speeds. The system has been proved in a commercial vehicle with satisfactory results.

Ultrasonic sensors in urban traffic driving-aid systems

Currently, vehicles are often equipped with active safety systems to reduce the risk of accidents, most of which occur in urban environments. The most prominent include Antilock Braking Systems (ABS), Traction Control and Stability Control. All these systems use different kinds of sensors to constantly monitor the conditions of the vehicle, and act in an emergency. In this paper the use of ultrasonic sensors in active safety systems for urban traffic is proposed, and the advantages and disadvantages when compared to other sensors are discussed. Adaptive Cruise Control (ACC) for urban traffic based on ultrasounds is presented as an application example. The proposed system has been implemented in a fully-automated prototype vehicle and has been tested under real traffic conditions. The results confirm the good performance of ultrasonic sensors in these systems. ©2011 by the authors.

Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Digital chaos synchronization in optical networks

A new method to obtain digital chaos synchronization between two systems is reported. It is based on the use of Optically Programmable Logic Cells as chaos generators. When these cells are feedbacked, periodic and chaotic behaviours are obtained. They depend on the ratio between internal and external delay times. Chaos synchronization is obtained if a common driving signal feeds both systems. A control to impose the same boundary conditions to both systems is added to the emitter. New techniques to analyse digital chaos are presented. The main application of these structures is to obtain secure communications in optical networks.

Non-periodic driving of coupled oscillators:a spherical swing

Nonlinearly coupled, damped oscillators at 1:1 frequency ratio, one oscillator being driven coherently for efficient excitation, are exemplified by a spherical swing with some phase-mismatch between drive and response. For certain damping range, excitation is found to succeed if it lags behind, but to produce a chaotic attractor if it leads the response. Although a period-doubhng sequence, for damping increasing, leads to the attractor, this is actually born as a hard (as regards amplitude) bifurcation at a zero growth-rate parametric line; as damping decreases, an unstable fixed point crosses an invariant plane to enter as saddle-focus a phase-space domain of physical solutions. A second hard bifurcation occurs at the zero mismatch line, the saddle-focus leaving that domain. Times on the attractor diverge when approaching either fine, leading to exactly one-dimensional and noninvertible limit maps, which are analytically determined.

Using floating car data to analyse the effects of ITS measures and eco-driving

The road transportation sector is responsible for around 25% of total man-made CO2 emissions worldwide. Considerable efforts are therefore underway to reduce these emissions using several approaches, including improved vehicle technologies, traffic management and changing driving behaviour. Detailed traffic and emissions models are used extensively to assess the potential effects of these measures. However, if the input and calibration data are not sufficiently detailed there is an inherent risk that the results may be inaccurate. This article presents the use of Floating Car Data to derive useful speed and acceleration values in the process of traffic model calibration as a means of ensuring more accurate results when simulating the effects of particular measures. The data acquired includes instantaneous GPS coordinates to track and select the itineraries, and speed and engine performance extracted directly from the on-board diagnostics system. Once the data is processed, the variations in several calibration parameters can be analyzed by comparing the base case model with the measure application scenarios. Depending on the measure, the results show changes of up to 6.4% in maximum speed values, and reductions of nearly 15% in acceleration and braking levels, especially when eco-driving is applied.

Factors driving the carbon mineralization priming effect in a sandy loam soil amended with different types of biochar

The effect of biochar on the soil carbon mineral- ization priming effect depends on the characteristics of the raw materials, production method and pyrolysis conditions. The goal of the present study is to evaluate the impact of three different types of biochar on physicochemical properties and CO2 emissions of a sandy loam soil. For this purpose, soil was amended with three different biochars (BI, BII and BIII) at a rate of 8 wt % and soil CO2 emissions were measured for 45 days. BI is produced from a mixed wood sieving from wood chip production, BII from a mixture of paper sludge and wheat husks and BIII from sewage sludge. Cumulative CO2 emissions of biochars, soil and amended soil were well fit to a simple first-order kinetic model with correlation coef- ficients (r 2 ) greater than 0.97. Results show a negative prim- ing effect in the soil after addition of BI and a positive prim- ing effect in the case of soil amended with BII and BIII. These results can be related to different biochar properties such as carbon content, carbon aromaticity, volatile matter, fixed carbon, easily oxidized organic carbon or metal and phenolic substance content in addition to surface biochar properties. Three biochars increased the values of soil field capacity and wilting point, while effects over pH and cation exchange capacity were not observed.

Considering cycling for commuting : the role of mode familiarity : an exploration on the (circular) relation between cycling behaviours and attitudes toward cycling in Vitoria-Gasteiz, Spain

¿La gente utiliza la bicicleta porque les gusta? ¿O es el propio hecho de usarla la razón por la que les gusta hacerlo? ¿O es una combinación de las dos? Este tipo de preguntas reflejan un problema que se puede llamar ‘el círculo de la consideración de la bicicleta’: para poder considerar el uso de la bicicleta en el conjunto de posibles opciones a escoger, un individuo tiene que tener creencias positivas sobre ella, sobre todo en el caso de ‘contextos de bajo uso’. Pero parece poco probable que se formen creencias positivas cuando hay bajos niveles de familiaridad al modo, es decir, con un bajo conocimiento de sus características, su funcionamiento y del imaginario asociado; al mismo tiempo, la familiaridad irá alcanzando niveles más altos conforme aumente el tiempo y la intensidad con la que se utilice la bicicleta a lo largo de la vida de los individuos. El problema parece un circulo recursivo huevo-gallina, ya que es difícil que alguien considere el usar la bicicleta en lugares donde su uso es una práctica poco extendida. En estos lugares, y dentro del conglomerado actual de tecnologías, infraestructuras, reglas, prácticas de los usuarios y preferencias culturales que se han desarrollado alrededor del automóvil (el actual "sistema socio-técnico de la movilidad urbana", Urry 2004; Geels 2005, 2012) usar la bicicleta es considerado por la mayoría como algo difícil, inseguro, y anormal. Como consecuencia, los procesos de aumento de familiaridad con la bicicleta permanecen inactivos. La tesis asume la familiaridad como una fuente de información e influencia sobre las creencias positivas sobre la bicicleta. En ‘contextos de bajo uso’, sin familiaridad al uso de la bicicleta, estas creencias sólo pueden surgir de ciertos rasgos personales (afecto, valores, identidades, voluntad, etc.). Tal como han evidenciado investigaciones recientes, en estos contextos la posibilidad de considerar el uso de la bicicleta (y su eventual adopción), se circunscribe principalmente a los ‘entusiastas’, a los que están dispuestos a “ir contra corriente” (Horton & Parkin 2012), limitando el alcance de las políticas de promoción. La investigación llevada a cabo en esta tesis ofrece un nuevo enfoque al problema del ‘círculo de la consideración de la bicicleta’. Para ello, plantea un modelo en el que se introduce a la familiaridad como un constructo que media entre el comportamiento final –qué modo de transporte elige el individuo– y el conjunto de constructos psicosociales que preceden la elección modal (creencias y actitudes). La familiaridad al uso de la bicicleta se concibe como una medida de la intensidad relativa del uso de una bicicleta, real y percibida (basándose en Diana & Mokhtarian 2009) que puede formarse de manera distinta según sus fines (utilitarios o no utilitarios). El constructo familiaridad con el modo bicicleta está relacionado con la cantidad de tiempo, la intensidad y la regularidad con la que un individuo ha hecho uso de la bicicleta a lo largo de su vida. La familiaridad se concibe así como una condición que permite definir adecuadamente el contexto en el que se toman las decisiones modales de los individuos, en línea con investigaciones que postulan patrones de causalidad alternativos entre los procesos cognitivos de elección y los comportamientos modales (Tardif 1977; Dobson et al. 1978; Golob et al. 1979; Golob 2001; Schwanen et al. 2012; Diana et al. 2009; Vij & Walker 2014). De este modo se plantea que el esquema unidireccional actitudesconductas podría no ser completamente valido en el caso de la consideración de la bicicleta, explorando la hipótesis que sean las propias conductas a influenciar la formación de las actitudes. En esta tesis, el constructo de familiaridad se articula teórica y metodológicamente, y se emplea un instrumento de diseño transversal para contrastarlo. Los resultados de una encuesta telefónica a una muestra representativa de 736 personas en la ciudad española de Vitoria-Gasteiz proveen evidencias que sugieren –aunque de forma preliminar– que la familiaridad juega un papel de mediadora en la relación entre la utilización de la bicicleta y la formación de las creencias y actitudes hacia el su uso. La tesis emplea mediciones para cada individuo con respecto tanto a su consideración como a su familiaridad al uso de la bicicleta. Éstas mediciones se definen haciendo uso del análisis factorial exploratorio (AFE). Por un lado, el AFE arroja una estructura del constructo ‘consideración’ formada por cuatro factores, tres de ellos asociados con elementos positivos y uno con elementos negativos: (1) de cómo el uso de la bicicleta se considera verde e inteligente (G&S); (2) sobre su carácter agradable y adecuado (P&S); (3) sobre su eficacia como modo de transporte para ir al trabajo (E); y (4) sobre los principales inconvenientes de su uso, es decir, las dificultades implícitas (sudoración y estar expuestos a las inclemencias del tiempo) y la sensación de inseguridad que genera (sentirse en riesgo de accidentes y estresarse por el tráfico) (D&T). Por otro lado, la familiaridad al uso de la bicicleta se mide en dos distintas variables ordinales (según se base en el uso utilitario o no utilitario). Como resultado, se puede hablar de que cada individuo se encuentra en una de las siguientes cuatro etapas en orden creciente hacia una familiaridad completa al modo: no familiarizados; apenas familiarizados; moderadamente familiarizados; totalmente familiarizados. El análisis de los datos de los cuatro grupos de sujetos de la muestra, –definidos de acuerdo con cada una de las cuatro etapas de familiaridad definidas– ha evidenciado la existencia de diferencias intergrupo estadísticamente significativas, especialmente para la medida relacionada con el uso utilitario. Asimismo, las personas en los niveles inferiores de familiaridad tienen una consideración menor de los aspectos positivos de la bicicleta y por el contrario presentan preocupaciones mayores hacia las características negativas respecto a aquellas personas que están más familiarizados en el uso utilitario. El uso, aunque esporádico, de una bicicleta para fines utilitarios (ir de compras, hacer recados, etc.), a diferencia de no usarla en absoluto, aparece asociado a unas puntuaciones significativamente más altas en los tres factores positivos (G&S, E, P&S), mientras que parece estar asociado a puntuaciones significativamente más bajas en el factor relacionado con las características negativas (D&U). Aparecen resultados similares cuando se compara un uso moderado, con uno esporádico, sobre todo con respecto a la consideración de las características negativas. Los resultados de esta tesis están en línea con la literatura anterior que se ha basado en variables similares (por ejemplo, de Geus et al. 2008; Stinson & Bhat 2003, 2004; Hunt & Abraham 2006; y van Bekkum et al. 2011a, entre otros), pero en este estudio las diferencias se observan en un contexto de bajo uso y se derivan de un análisis de toda la población de personas que se desplazan a su lugar de trabajo o estudio, lo cual eleva la fiabilidad de los resultados. La posibilidad de que unos niveles más altos de uso de la bicicleta para fines utilitarios puedan llevar a niveles más positivos de su consideración abre el camino a implicaciones teóricas y de políticas que se discuten en la tesis. Con estos resultados se argumenta que el enfoque convencional basado en el cambio de actitudes puede no ser el único y prioritario para lograr cambios a la hora de fomentar el uso de la bicicleta. Los resultados apuntan al potencial de otros esquemas de causalidad, basados en patrones de influencia más descentrados y distribuidos, y que adopten una mirada más positiva hacia los hábitos de transporte, conceptualizándolos como “inteligencia encarnada y pre-reflexiva” (Schwanen et al. 2012). Tales esquemas conducen a un enfoque más práctico para la promoción del uso de la bicicleta, con estrategias que podrían basarse en acciones de ‘degustación’ de su uso o de mayor ‘exposición’ a su uso. Is the fact that people like cycling the reason for them to cycle? Or is the fact that they do cycle the reason for them to like cycling? Or is a combination of the two? This kind of questions reflect a problem that can be called ‘the cycle of cycling consideration’: in order to consider cycling in the set of possible options to be chosen, an individual needs to have positive beliefs about it, especially in the case of ‘low-cycling contexts’. However, positive beliefs seem unlikely to be formed with low levels of mode familiarity, say, with a low acquaintance with mode features, functioning and images; at the same time, higher levels of familiarity are likely to be reached if cycling is practised over relative threshold levels of intensities and extensively across individual life courses. The problem looks like a chicken-egg recursive cycle, since the latter condition is hardly met in places where cycling is little practised. In fact, inside the current conglomerate of technologies, infrastructures, regulations, user practices, cultural preferences that have grown around the automobile (the current “socio-technical system of urban mobility”, Urry 2004; Geels 2005, 2012) cycling is commonly considered as difficult, unsafe, and abnormal. Consequently, the processes of familiarity forming remain disabled, and, as a result, beliefs cannot rely on mode familiarity as a source of information and influence. Without cycling familiarity, origins of positive beliefs are supposed to rely only on personal traits (affect, values, identities, willingness, etc.), which, in low-cycling contexts, confine the possibility of cycling consideration (and eventual adoption) mainly to ‘cycling enthusiasts’ who are willing to “go against the grain” (Horton & Parkin 2012), as it results from previous research. New research conducted by author provides theoretical insights for a different approach of the cycling consideration problem in which the presence of the new construct of cycling familiarity is hypothesised in the relationship between mode choice behaviour and the set of psychosocial constructs that are supposed to precede it (beliefs and attitudes). Cycling familiarity is conceived as a measure of the real and the perceived relative intensity of use of a bicycle (building upon Diana & Mokhtarian 2009) which may be differently formed for utilitarian or non-utilitarian purposes. The construct is assumed to be related to the amount of time, the intensity and the regularity an individual spends in using a bicycle for the two distinct categories of purposes, gaining in this way a certain level of acquaintance with the mode. Familiarity with a mode of transport is conceived as an enabling condition to properly define the decision-making context in which individual travel mode choices are taken, in line with rather disperse research efforts postulating inverse relationships between mode behaviours and mode choices (Tardiff 1977; Dobson et al. 1978; Golob et al. 1979; Golob 2001; Schwanen et al. 2012; Diana et al. 2009; Vij & Walker 2014). The new construct is built theoretically and methodologically, and a cross-sectional design instrument is employed. Results from a telephone survey in a representative sample of 736 commuters in the Spanish city of Vitoria-Gasteiz, provide suggestive –although preliminary– evidence on the role of mode familiarity as a mediator in the relationship between cycling use and the formation of beliefs and attitudes toward cycling. Measures of both cycling consideration and cycling familiarity are defined making use of exploratory factor analysis. On the one hand, four distinct cycling consideration measures are created, based on attitude expressions on four underlying factors relating to the cycling commuting behaviour: on how cycling commuting is considered green and smart (G&S); on its pleasant and suited character (P&S); on its efficiency as a mode of transport for commuting (E); and on the main drawbacks of its use, namely the difficulties implied (sweating and being exposed to adverse weather conditions) and the sense of unsafety it generates (feeling at risk of accidents and getting stressed by traffic) (D&U). On the other hand, dimensions of cycling familiarity are measured on two distinct ordinal variables (whether based on the utilitarian or non-utilitarian use) comprising four stages to a complete mode familiarity: not familiar; barely familiar; moderately familiar; fully familiar. For each of the four stages of cycling familiarity defined, statistical significant differences are found, especially for the measure related to the utilitarian use. Consistently, people at the lower levels of cycling familiarity have a lower consideration of the positive aspects of cycling and conversely they exhibit higher concerns towards the negative characteristics than those individuals that are more familiar in utilitarian cycling. Using a bicycle occasionally for practical purposes, as opposed to not using it at all, seems associated to significant higher scores in the three positive factors (G&S, E, P&S) while it appears to be associated to significant lower scores in the factor relating with the negative characteristics of cycling commuting (D&U). A same pattern also occurs with a moderate use, as opposed to an occasional one, especially for the consideration of the negative characteristics. The results are in line with previous literature based on similar variables (e.g. de Geus et al. 2008; Stinson & Bhat 2003, 2004; Hunt & Abraham 2006; and van Bekkum et al. 2011a, among others), but in this study the differences are observed in a low-cycling context and derive from an analysis of the entire population of commuters, which rises the reliability of results.

Cognitive risk perception system for obstacle avoidance in outdoor mUAV missions

La robótica ha evolucionado exponencialmente en las últimas décadas, permitiendo a los sistemas actuales realizar tareas sumamente complejas con gran precisión, fiabilidad y velocidad. Sin embargo, este desarrollo ha estado asociado a un mayor grado de especialización y particularización de las tecnologías implicadas, siendo estas muy eficientes en situaciones concretas y controladas, pero incapaces en entornos cambiantes, dinámicos y desestructurados. Por eso, el desarrollo de la robótica debe pasar por dotar a los sistemas de capacidad de adaptación a las circunstancias, de entendedimiento sobre los cambios observados y de flexibilidad a la hora de interactuar con el entorno. Estas son las caracteristicas propias de la interacción del ser humano con su entorno, las que le permiten sobrevivir y las que pueden proporcionar a un sistema inteligencia y capacidad suficientes para desenvolverse en un entorno real de forma autónoma e independiente. Esta adaptabilidad es especialmente importante en el manejo de riesgos e incetidumbres, puesto que es el mecanismo que permite contextualizar y evaluar las amenazas para proporcionar una respuesta adecuada. Así, por ejemplo, cuando una persona se mueve e interactua con su entorno, no evalúa los obstáculos en función de su posición, velocidad o dinámica (como hacen los sistemas robóticos tradicionales), sino mediante la estimación del riesgo potencial que estos elementos suponen para la persona. Esta evaluación se consigue combinando dos procesos psicofísicos del ser humano: por un lado, la percepción humana analiza los elementos relevantes del entorno, tratando de entender su naturaleza a partir de patrones de comportamiento, propiedades asociadas u otros rasgos distintivos. Por otro lado, como segundo nivel de evaluación, el entendimiento de esta naturaleza permite al ser humano conocer/estimar la relación de los elementos con él mismo, así como sus implicaciones en cuanto a nivel de riesgo se refiere. El establecimiento de estas relaciones semánticas -llamado cognición- es la única forma de definir el nivel de riesgo de manera absoluta y de generar una respuesta adecuada al mismo. No necesariamente proporcional, sino coherente con el riesgo al que se enfrenta. La investigación que presenta esta tesis describe el trabajo realizado para trasladar esta metodología de análisis y funcionamiento a la robótica. Este se ha centrado especialmente en la nevegación de los robots aéreos, diseñando e implementado procedimientos de inspiración humana para garantizar la seguridad de la misma. Para ello se han estudiado y evaluado los mecanismos de percepción, cognición y reacción humanas en relación al manejo de riesgos. También se ha analizado como los estímulos son capturados, procesados y transformados por condicionantes psicológicos, sociológicos y antropológicos de los seres humanos. Finalmente, también se ha analizado como estos factores motivan y descandenan las reacciones humanas frente a los peligros. Como resultado de este estudio, todos estos procesos, comportamientos y condicionantes de la conducta humana se han reproducido en un framework que se ha estructurado basadandose en factores análogos. Este emplea el conocimiento obtenido experimentalmente en forma de algoritmos, técnicas y estrategias, emulando el comportamiento humano en las mismas circunstancias. Diseñado, implementeado y validado tanto en simulación como con datos reales, este framework propone una manera innovadora -tanto en metodología como en procedimiento- de entender y reaccionar frente a las amenazas potenciales de una misión robótica. ABSTRACT Robotics has undergone a great revolution in the last decades. Nowadays this technology is able to perform really complex tasks with a high degree of accuracy and speed, however this is only true in precisely defined situations with fully controlled variables. Since the real world is dynamic, changing and unstructured, flexible and non context-dependent systems are required. The ability to understand situations, acknowledge changes and balance reactions is required by robots to successfully interact with their surroundings in a fully autonomous fashion. In fact, it is those very processes that define human interactions with the environment. Social relationships, driving or risk/incertitude management... in all these activities and systems, context understanding and adaptability are what allow human beings to survive: contrarily to the traditional robotics, people do not evaluate obstacles according to their position but according to the potential risk their presence imply. In this sense, human perception looks for information which goes beyond location, speed and dynamics (the usual data used in traditional obstacle avoidance systems). Specific features in the behaviour of a particular element allows the understanding of that element’s nature and therefore the comprehension of the risk posed by it. This process defines the second main difference between traditional obstacle avoidance systems and human behaviour: the ability to understand a situation/scenario allows to get to know the implications of the elements and their relationship with the observer. Establishing these semantic relationships -named cognition- is the only way to estimate the actual danger level of an element. Furthermore, only the application of this knowledge allows the generation of coherent, suitable and adjusted responses to deal with any risk faced. The research presented in this thesis summarizes the work done towards translating these human cognitive/reasoning procedures to the field of robotics. More specifically, the work done has been focused on employing human-based methodologies to enable aerial robots to navigate safely. To this effect, human perception, cognition and reaction processes concerning risk management have been experimentally studied; as well as the acquisition and processing of stimuli. How psychological, sociological and anthropological factors modify, balance and give shape to those stimuli has been researched. And finally, the way in which these factors motivate the human behaviour according to different mindsets and priorities has been established. This associative workflow has been reproduced by establishing an equivalent structure and defining similar factors and sources. Besides, all the knowledge obtained experimentally has been applied in the form of algorithms, techniques and strategies which emulate the analogous human behaviours. As a result, a framework capable of understanding and reacting in response to stimuli has been implemented and validated.

Understanding how to reduce road transport emissions : modelling the impact of eco-driving

Entre los problemas medioambientales más trascendentales para la sociedad, se encuentra el del cambio climático así como el de la calidad del aire en nuestras áreas metropolitanas. El transporte por carretera es uno de los principales causantes, y como tal, las administraciones públicas se enfrentan a estos problemas desde varios ángulos: Cambios a modos de transporte más limpios, nuevas tecnologías y combustibles en los vehículos, gestión de la demanda y el uso de tecnologías de la información y la comunicación (ICT) aplicadas al transporte. En esta tesis doctoral se plantea como primer objetivo el profundizar en la comprensión de cómo ciertas medidas ICT afectan al tráfico, las emisiones y la propia dinámica de los vehículos. El estudio se basa en una campaña de recogida de datos con vehículos flotantes para evaluar los impactos de cuatro medidas concretas: Control de velocidad por tramo, límites variables de velocidad, limitador de velocidad (control de crucero) y conducción eficiente (eco‐driving). Como segundo objetivo, el estudio se centra en la conducción eficiente, ya que es una de las medidas que más ahorros de combustible presenta a nivel individual. Aunque estas reducciones están suficientemente documentadas en la literatura, muy pocos estudios se centran en estudiar el efecto que los conductores eficientes pueden tener en el flujo de tráfico, y cuál sería el impacto si se fuera aumentando el porcentaje de este tipo de conductores. A través de una herramienta de microsimulación de tráfico, se han construido cuatro modelos de vías urbanas que se corresponden con una autopista urbana, una arteria, un colector y una vía local. Gracias a los datos recogidos en la campaña de vehículos flotantes, se ha calibrado el modelo, tanto el escenario base como el ajuste de parámetros de conducción para simular la conducción eficiente. En total se han simulado 72 escenarios, variando el tipo de vía, la demanda de tráfico y el porcentaje de conductores eficientes. A continuación se han calculado las emisiones de CO2 and NOx mediante un modelo de emisiones a nivel microscópico. Los resultados muestran que en escenarios con alto porcentaje de conductores eficientes y altas demandas de tráfico las emisiones aumentan. Esto se debe a que las mayores distancias de seguridad y las aceleraciones y frenadas suaves hacen que aumente la congestión, produciendo así mayores emisiones a nivel global. Climate change and the reduced air quality in our metropolitan areas are two of the main environmental problems that the society is addressing currently. Being road transportation one of the main contributors, public administrations are facing these problems from different points of view: shift to cleaner modes, new fuels and vehicle technologies, demand management and the use of information and communication technologies (ICT) applied to transportation. The first objective of this thesis is to understand how certain ICT measures affect traffic, emissions and vehicle dynamics. The study is based on a data collection campaign with floating vehicles to evaluate the impact of four specific measures: section speed control, variable speed limits, cruise control and eco‐driving. The second objective of the study focuses on eco‐driving, as it is one of the measures that present the largest fuel savings at an individual level. Although these savings are well documented in the literature, few studies focus on how ecodrivers affect the surrounding vehicles and the traffic, and what would be the impact in case of different eco‐drivers percentage. Using a traffic micro‐simulation tool, four models in urban context have been built, corresponding to urban motorway, urban arterial, urban collector and a local street. Both the base‐case and the parameters setting to simulate eco‐driving have been calibrated with the data collected through floating vehicles. In total 72 scenarios were simulated, varying the type of road, traffic demand and the percentage of eco‐drivers. Then, the CO2 and NOx emissions have been estimated through the use of an emission model at microscopic level. The results show that in scenarios with high percentage of co‐drivers and high traffic demand the emissions rise. Higher headways and smooth acceleration and decelerations increase congestion, producing higher emissions globally.