Aerodinámica experimental de elementos de parques energéticos

La creciente demanda de energía eléctrica y la necesidad de implementar energías no contaminantes hace que las llamadas tecnologías verdes sean cada día más solicitadas. Entre estas tecnologías encontramos la energía solar y la energía eólica; ambas tienen una trayectoria de uso e investigación bastante amplia, sin embargo aún presentan problemas de fondo que impiden dar mayor impulso a su uso. El objetivo de la presente tesis es presentar soluciones a problemas de optimización en campos conversores de energía. Para ello se analizan y resuelven dos problemas por medio de técnicas de aerodinámica experimental: el primero sobre campos de colectores solares y el segundo sobre campos eólicos. Las técnicas de medición utilizadas en aerodinámica, y en el presente trabajo, son: medición de cargas, anemometría de hilo caliente, velocimetría por imagen de partículas y escaneo de presiones; además de un análisis estadístico de los datos. En el primer caso se ensayan experimentalmente colectores solares parabólicos en donde, por cuestiones de seguridad o por protección contra el viento, se utilizan cercas. Éstas modifican el comportamiento del flujo corriente abajo y se ha encontrado que la distancia a la cual se colocan, así como el tipo de cercas (sólida o permeable), modifican las cargas estructurales a las que los colectores están expuestos. Los resultados demuestran que existe una distancia crítica en la cual la presencia de la cerca aumenta la carga en lugar de disminuirla, por lo cual la selección adecuada del parapeto y la distancia a la cual se coloca son de suma importancia para la optimización de la estructura. En el segundo caso se ensaya experimentalmente y simula numéricamente la estela de turbinas eólicas por medio de discos porosos. En donde un disco permeable simula el rotor de una turbina. El disco es capaz de semejar la estela y los efectos que ésta puede causar corriente abajo. Los resultados muestran que seleccionando adecuadamente la porosidad, es posible simular coeficientes de empuje similares a los desarrollados por los aerogeneradores, además la estela y sus efectos son semejantes a los medidos en campo. ABSTRACT The called green energy technologies are increasingly required because of the growing demand for electricity and the need to implement nonpolluting energy. Among the green energy technologies it is found the solar and the wind energy, both have a history of use and fairly extensive research; however they still have problems which limit to give them further impetus to its use. The aim of this thesis is to present solutions to optimization problems in energy harvesting. To this end it is analysed, and solved, two problems by means of techniques in experimental aerodynamics: the first issue with regard to parabolic troughs and the second about wind farms. The measurement techniques commonly used in aerodynamics, and used in this research work, are: measurement of loads, hot wire anemometry, particle image velocimetry and scanning of pressures; where data are collected and then an statistical analysis is done. In the first case it is tested parabolic troughs where, either for security reasons or protection against the wind actions, fences are used. These fences modify the behaviour of flow downstream and it was found that the distance at which they are placed, and the type of fences (solid or permeable) modify the structural loads to which the parabolic troughs are exposed. The results show that there is a critical distance at which the presence of the fence increases the load instead of protecting the parabolic trough, hence making the proper selection of the parapet and the distance at which it stands are paramount for the optimization of the structure. In the second case it is tested, experimentally and numerically, the wake of wind turbines by means of porous disks; where the permeable disc simulates a turbine rotor. The disc is able to mimic the wake and the effects that it can cause downstream. The results show that by properly selecting the porosity, it is possible to simulate drag coefficients similar to those developed by wind turbines; moreover the porous disk wake and its effects are similar to those measured on field.

Analysis of air flow past and through the 2415-3S airfoil for an unmanned aerial vehicle with internal propulsion system

This paper deals with the prediction of velocity fields on the 2415-3S airfoil which will be used for an unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is three-dimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software, respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-e model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.

Numerical analysis of air flow past the 2415-3S airfoil for an unmanned aerial vehicle with internal propulsion system

This paper deals with the prediction of pressure and velocity fields on the 2415-3S airfoil which will be used for and unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is tridimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-ε model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining pressure and velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.

An engineering modification of the blade element momentum combination applicable in vertical descent flight :fundamentals and validation

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non‐linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

An engineering modification of the blade element momentum equation for vertical descent : an autoration case study

An engineering modification of blade element/momentum theory is applied to describe the vertical autorotation of helicopter rotors. A full non-linear aerodynamic model is considered for the airfoils, taking into account the dependence of lift and drag coefficients on both the angle of attack and the Reynolds number. The proposed model, which has been validated in previous work, has allowed the identification of different autorotation modes, which depend on the descent velocity and the twist of the rotor blades. These modes present different radial distributions of driven and driving blade regions, as well as different radial upwash/downwash patterns. The number of blade sections with zero tangential force, the existence of a downwash region in the rotor disk, the stability of the autorotation state, and the overall rotor autorotation efficiency, are all analyzed in terms of the flight velocity and the characteristics of the rotor. It is shown that, in vertical autorotation, larger blade twist leads to smaller values of descent velocity for a given thrust generated by the rotor in the autorotational state.

The application of biomechanics to penalty corner drag-flick training: a case of Study

The penalty corner is one of the most important game situations in field hockey with one third of all goals resulting from this tactical situation. The aim of this study was to develop and apply a training method, based on previous studies, to improve the drag- flick skill on a young top-class field hockey player. A young top-class player exercised three times per week using specific drills over a four week period. A VICON optoelectronic system (Oxford Metrics, Oxford, UK) was employed to capture twenty drag-flicks, with six cameras sampling at 250 Hz, prior and after the training period. In order to analyze pre- and post-test differences a dependent t-test was carried out. Angular velocities and the kinematic sequence were similar to previous studies. The player improved (albeit not significantly) the angular velocity of the stick. The player increased front foot to the ball at T1 (p < 0.01) and the drag-flick distances. The range of motion from the front leg decreased from T1 to T6 after the training period (p < 0.01). The specific training sessions conducted with the player improved some features of this particular skill. This article shows how technical knowledge can help with the design of training programs and whether some drills are more effective than others.

Evapotranspiration and crop coefficients of rice (Oryza sativa L.) under sprinkler irrigation in a semiarid climate determined by the surface renewal method

The evapotranspiration (ETc) of sprinkler-irrigated rice was determined for the semiarid conditions of NE Spain during 2001, 2002 and 2003. The surface renewal method, after calibration against the eddy covariance method, was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Latent heat flux values were obtained by solving the energy balance equation. Finally, lysimeter measurements were used to validate the evapotranspiration values obtained with the surface renewal method. Seasonal rice evapotranspiration was about 750–800 mm. Average daily ETc for mid-season (from 90 to 130 days after sowing) was 5.1, 4.5 and 6.1 mm day−1 for 2001, 2002 and 2003, respectively. The experimental weekly crop coefficients fluctuated in the range of 0.83–1.20 for 2001, 0.81–1.03 for 2002 and 0.84–1.15 for 2003. The total growing season was about 150–160 days. In average, the crop coefficients for the initial (Kcini), mid-season (Kcmid) and late-season stages (Kcend) were 0.92, 1.06 and 1.03, respectively, the length of these stages being about 55, 45 and 25 days, respectively.

Control rod drop surveillance using two friction coefficients

In the case of large burnup, a control rod (CR) guide tube in the pressurized water reactor of a commercial nuclear power plant might bend. As a consequence, a CR drop experiment may indicate an event of a CR partially inserted and whether the CR should be deemed inoperable. Early prevention of such an event can be achieved by measuring two friction coefficients: the hydraulic coefficient and the sliding coefficient. The hydraulic coefficient hardly changes, so that the curvature of the guide tube can only be detected thanks to a variation of the sliding coefficient. A simple model for the CR drop is established and validated with CR drop experiments. If tmx denotes the instant of CR maximum velocity, a linear relationship between (tmx)_2 and the sliding coefficient is found.

The interurban DRAG-Spain model: the main factors of influence on road accidents in Spain

This paper presents the results of applying DRAG methodology to the identification of the main factors of influence on the number of injury and fatal accidents occurring on Spain’s interurban network. Nineteen independent variables have been included in the model grouped together under ten categories: exposure, infrastructure, weather, drivers, economic variables, vehicle stock, surveillance, speed and legislative measures. Highly interesting conclusions can be reached from the results on the basis of the different effects of a single variable on each of the accident types according to severity. The greatest influence revealed by the results is exposure, which together with inexperienced drivers, speed and an ageing vehicle stock, have a negative effect, while the increased surveillance on roads, the improvement in the technological features of vehicles and the proportion of high capacity networks have a positive effect, since the results obtained show a significant drop in accidents.

Kinematic pattern of the drag-flick: a case study

The drag-flick is more efficient than hits or pushes when a penalty corner situation is in effect in field hockey. Previous research has studied the biomechanical pattern of the drag-flick, trying to find the cues for an optimal performance. On the other hand, some other studies have examined the most effective visual pick-up of relevant information in shots and goalkeeper anticipation. The aim of this study was to analyse the individual differences in the drag-flick pattern in order to provide relevant information for goalkeepers. One female skilled drag-flicker participated in the study. A VICON optoelectronic sy stem (Oxford Metrics, Oxford, UK) was used to capture the drag-flicks with six cameras. The results showed that the main significant differences between right and left shots (p<0.05) in the stick angles, stick minimum angular velocity and front foot-ball distance were when the front foot heel contacted the floor(T1) and at the minimum velocity of the stick, before the dragging action (T3). The findings showed that the most relevant information might be picked up at the ball-and-stick location before the dragging action.

Training-induced changes in drag-flick technique in female field hockey players

The penalty corner is one of the most important goal plays in field hockey. The drag-flick is used less by women than men in a penalty corner. The aim of this study was to describe training-induced changes in the drag-flick technique in female field hockey players. Four female players participated in the study. The VICON optoelectronic system (Oxford Metrics, Oxford, UK) measured the kinematic parameters of the drag-flick with six cameras sampling at 250 Hz, prior to and after training. Fifteen shots were captured for each subject. A Wilcoxon test assessed the differences between pre-training and post-training parameters. Two players received specific training twice a week for 8 weeks; the other two players did not train. The proposed drills improved the position of the stick at the beginning of the shot (p<0.05), the total distance of the shot (p<0.05)and the rotation radius at ball release (p<0.01). It was noted that all players had lost speed of the previous run. Further studies should include a larger sample, in order to provide more information on field hockey performance.

Orbital debris mitigation through deorbiting with passive electrodynamic drag

The increase of orbital debris and the consequent proliferation of smaller objects through fragmentation are driving the need for mitigation strategies. The issue is how to deorbit the satellite with an efficient system that does not impair drastically the propellant budget of the satellite and, consequently, reduces its operating life. We have been investigating, in the framework of a European-Community-funded project, a passive system that makes use of an electrodynamics tether to deorbit a satellite through Lorentz forces. The deorbiting system will be carried by the satellite itself at launch and deployed from the satellite at the end of its life. From that moment onward the system operates passively without requiring any intervention from the satellite itself. The paper summarizes the results of the analysis carried out to show the deorbiting performance of the system starting from different orbital altitudes and inclinations for a reference satellite mass. Results can be easily scaled to other satellite masses. The results have been obtained by using a high-fidelity computer model that uses the latest environmental routines for magnetic field, ionospheric density, atmospheric density and a gravity field model. The tether dynamics is modelled by considering all the main aspects of a real system as the tether flexibility and its temperature-dependent electrical conductivity. Temperature variations are computed by including all the major external and internal input fluxes and the thermal flux emitted from the tether. The results shows that a relatively compact and light system can carry out the complete deorbit of a relatively large satellite in a time ranging from a month to less than a year starting from high LEO with the best performance occurring at low orbital inclinations.

Influence of air drag on the optimal hand launching of a small, round projectile

Conditions leading to a maximum range for a small, round projectile, fired by hand, are discussed taking into account air drag and the dependence of the initial speed on the mass launched. Both the optimal angle of release for given projectile and initial speed, and the optimal radius for given density (i.e., among a bed of pebbles) are determined; an increase on the height of release is found to always decrease the angle and increase the radius. The influence of the projectile mass on the optimal manner of launching is considered. The validity of the approximations used in the analysis is discussed. Results from very simple measurements show good agreement with theory.

Spherical collectors versus bare tethers for drag, thrust, and power generation

Deorbit, power generation, and thrusting performances of a bare thin-tape tether and an insulated tether with a spherical electron collector are compared for typical conditions in low-Earth orbit and common values of length L = 4−20 km and cross-sectional area of the tether A = 1−5 mm2. The relative performance of moderately large spheres, as compared with bare tapes, improves but still lags as one moves from deorbiting to power generation and to thrusting: Maximum drag in deorbiting requires maximum current and, thus, fully reflects on anodic collection capability, whereas extracting power at a load or using a supply to push current against the motional field requires reduced currents. The relative performance also improves as one moves to smaller A, which makes the sphere approach the limiting short-circuit current, and at greater L, with the higher bias only affecting moderately the already large bare-tape current. For a 4-m-diameter sphere, relative performances range from 0.09 sphere-to-bare tether drag ratio for L = 4 km and A = 5 mm2 to 0.82 thrust–efficiency ratio for L = 20 km and A = 1 mm2. Extremely large spheres collecting the short-circuit current at zero bias at daytime (diameters being about 14 m for A = 1 mm2 and 31 m for A = 5 mm2) barely outperform the bare tape for L = 4 km and are still outperformed by the bare tape for L = 20 km in both deorbiting and power generation; these large spheres perform like the bare tape in thrusting. In no case was sphere or sphere-related hardware taken into account in evaluating system mass, which would have reduced the sphere performances even further.

On the charged particle drag acting on LAGEOS

A recent study by the authors points to Charged Particle Drag (CPD) as a contributor to revisit in the LAGEOS non-gravitational perturbations problem. Such perturbations must account for dynamical contributions in the order of pms−2 . The simulated effect takes into account: (i) spatial and temporal variations of the plasmatic parameters (temperature and concentration of the species), (ii) spacecraft potential variations caused by both the eclipse passages and variations in the parameters mentioned above, and (iii) solar and geomagnetic conditions. Furthermore, recent theoretical improvements concerning scattering drag overcome previous limitations allowing for a complete formulation of this effect. For each satellite the lifetime CPD instantaneous acceleration is computed. The plasmatic parameters have been obtained fromthe Sheffield Coupled Thermosphere-Ionosphere-Plasmasphere (SCTIP) semi-empirical model (up to the polar region), as well as alytical/empirical approximations based on spacecraft measurements for the auroral and polar regions. Results show that maximum amplitudes for LAGEOSI are larger than those for LAGEOS-II: −85 pms−2 and −70 pms−2 respectively. This is due to the almost (magnetically) polar orbit configuration of the first, producing larger combinations of plasmatic parameter values. High solar activity has a huge impact in the resulting LAGEOS accelerations: it yields a perfect modulation of the resulting acceleration with maximum amplitudes up to a factor of 10 when comparing low and high activity periods. On the other hand, the impact of the geomagnetic activity results into a reduction of the effect itself, probably due to a decrease in the hydrogen concentration for high energy input periods. The acceleration results will be used in a refined orbit computation in a subsequent investigation.