Use of calculus of variations to determine the shape of hovering rotors of minimum power and its application to micro air vehicles

In this paper, calculus of variations and combined blade element and momentum theory (BEMT) are used to demonstrate that, in hover, when neither root nor tip losses are considered; the rotor, which minimizes the total power (MPR), generates an induced velocity that varies linearly along the blade span. The angle of attack of every blade element is constant and equal to its optimum value. The traditional ideal twist (ITR) and optimum (OR) rotors are revisited in the context of this variational framework. Two more optimum rotors are obtained considering root and tip losses, the ORL, and the MPRL. A comparison between these five rotors is presented and discussed. The MPR and MPRL present a remarkable saving of power for low values of both thrust coefficient and maximum aerodynamic efficiency. The result obtained can be exploited to improve the aerodynamic behaviour of rotary wing micro air vehicles (MAV). A comparison with experimental results obtained from the literature is presented.

Dynamic response of hydro power plants to load variations for providing secondary regulation reserves considering elastic water column effects

In this paper, the dynamic response of a hydro power plant for providing secondary regulation reserve is studied in detail. S pecial emphasis is given to the elastic water column effects both in the penstock and the tailrace tunnel. For this purpose, a nonline ar model based on the analogy between mass and momentum conservation equations of a water conduit and those of wave propagation in transmission lines is used. The influence of the plant configuration and design parameters on the fulfilment of the Spanish Electrical System Operator requirem ents is analysed.

Ratio-based temperature-sensing technique hardened against nanometer process variations

This letter presents a temperature-sensing technique on the basis of the temperature dependency of MOSFET leakage currents. To mitigate the effects of process variation, the ratio of two different leakage current measurements is calculated. Simulations show that this ratio is robust to process spread. The resulting sensor is quite small-0.0016 mm2 including an analog-to-digital conversion-and very energy efficient, consuming less than 640 pJ/conversion. After a two-point calibration, the accuracy in a range of 40°C-110°C is less than 1.5°C , which makes the technique suitable for thermal management applications.

Modelling experiments of the variations of the calving front position of Hansbreen, Svalbard

Hansbreen is a tidewater glacier in Svalbard, with grounded tongue, about 16 km in length and ca. 2.5 km in width at its tongue. The calving front position has shown, over the recent decades, a general retreating trend, often rather smooth but with some occasional abrupt changes. We apply a full-Stokes model of glacier dynamics, incorporating a crevasse-depth calving model, with the aim of reproducing the glacier front positions observed since 1936 and analyzing the sensitivity of the model to environmental parameters.

Conductivity variations of multi-walled carbon nanotubes oriented in liquid crystal cells

The control of carbon nanotubes conductivity is generating interest in several fields since it may be relevant for a number of applications. The self-organizing properties of liquid crystals may be used to impose alignment on dispersed carbon nanotubes,thus control-ling their conductivity and its anisotropy. This leads to a number of possible applications in photonic and electronic devices such as electrically controlled carbon nanotube switch- es and crossboards. In this work, cells of liquid crystals doped with multi-walled nanotubes have been prepared in different configurations. Their conductivity variations upon switching have been investigated. It turns out that conductivity evolution depends on the initial configuration (either homogeneous, homeotropic or in-plane switching), the cell thickness and the switching record. The control of these manufacturing paramenters allows the modulation of the electrical behavior of carbon nanotubes.

Correction of the Colour Variations under Uncontrolled Lighting Conditions

Esta tesis trata sobre métodos de corrección que compensan la variación de las condiciones de iluminación en aplicaciones de imagen y video a color. Estas variaciones hacen que a menudo fallen aquellos algoritmos de visión artificial que utilizan características de color para describir los objetos. Se formulan tres preguntas de investigación que definen el marco de trabajo de esta tesis. La primera cuestión aborda las similitudes que se dan entre las imágenes de superficies adyacentes en relación a su comportamiento fotométrico. En base al análisis del modelo de formación de imágenes en situaciones dinámicas, esta tesis propone un modelo capaz de predecir las variaciones de color de la región de una determinada imagen a partir de las variaciones de las regiones colindantes. Dicho modelo se denomina Quotient Relational Model of Regions. Este modelo es válido cuando: las fuentes de luz iluminan todas las superficies incluídas en él; estas superficies están próximas entre sí y tienen orientaciones similares; y cuando son en su mayoría lambertianas. Bajo ciertas circunstancias, la respuesta fotométrica de una región se puede relacionar con el resto mediante una combinación lineal. No se ha podido encontrar en la literatura científica ningún trabajo previo que proponga este tipo de modelo relacional. La segunda cuestión va un paso más allá y se pregunta si estas similitudes se pueden utilizar para corregir variaciones fotométricas desconocidas en una región también desconocida, a partir de regiones conocidas adyacentes. Para ello, se propone un método llamado Linear Correction Mapping capaz de dar una respuesta afirmativa a esta cuestión bajo las circunstancias caracterizadas previamente. Para calcular los parámetros del modelo se requiere una etapa de entrenamiento previo. El método, que inicialmente funciona para una sola cámara, se amplía para funcionar en arquitecturas con varias cámaras sin solape entre sus campos visuales. Para ello, tan solo se necesitan varias muestras de imágenes del mismo objeto capturadas por todas las cámaras. Además, este método tiene en cuenta tanto las variaciones de iluminación, como los cambios en los parámetros de exposición de las cámaras. Todos los métodos de corrección de imagen fallan cuando la imagen del objeto que tiene que ser corregido está sobreexpuesta o cuando su relación señal a ruido es muy baja. Así, la tercera cuestión se refiere a si se puede establecer un proceso de control de la adquisición que permita obtener una exposición óptima cuando las condiciones de iluminación no están controladas. De este modo, se propone un método denominado Camera Exposure Control capaz de mantener una exposición adecuada siempre y cuando las variaciones de iluminación puedan recogerse dentro del margen dinámico de la cámara. Los métodos propuestos se evaluaron individualmente. La metodología llevada a cabo en los experimentos consistió en, primero, seleccionar algunos escenarios que cubrieran situaciones representativas donde los métodos fueran válidos teóricamente. El Linear Correction Mapping fue validado en tres aplicaciones de re-identificación de objetos (vehículos, caras y personas) que utilizaban como caracterísiticas la distribución de color de éstos. Por otra parte, el Camera Exposure Control se probó en un parking al aire libre. Además de esto, se definieron varios indicadores que permitieron comparar objetivamente los resultados de los métodos propuestos con otros métodos relevantes de corrección y auto exposición referidos en el estado del arte. Los resultados de la evaluación demostraron que los métodos propuestos mejoran los métodos comparados en la mayoría de las situaciones. Basándose en los resultados obtenidos, se puede decir que las respuestas a las preguntas de investigación planteadas son afirmativas, aunque en circunstancias limitadas. Esto quiere decir que, las hipótesis planteadas respecto a la predicción, la corrección basada en ésta y la auto exposición, son factibles en aquellas situaciones identificadas a lo largo de la tesis pero que, sin embargo, no se puede garantizar que se cumplan de manera general. Por otra parte, se señalan como trabajo de investigación futuro algunas cuestiones nuevas y retos científicos que aparecen a partir del trabajo presentado en esta tesis. ABSTRACT This thesis discusses the correction methods used to compensate the variation of lighting conditions in colour image and video applications. These variations are such that Computer Vision algorithms that use colour features to describe objects mostly fail. Three research questions are formulated that define the framework of the thesis. The first question addresses the similarities of the photometric behaviour between images of dissimilar adjacent surfaces. Based on the analysis of the image formation model in dynamic situations, this thesis proposes a model that predicts the colour variations of the region of an image from the variations of the surrounded regions. This proposed model is called the Quotient Relational Model of Regions. This model is valid when the light sources illuminate all of the surfaces included in the model; these surfaces are placed close each other, have similar orientations, and are primarily Lambertian. Under certain circumstances, a linear combination is established between the photometric responses of the regions. Previous work that proposed such a relational model was not found in the scientific literature. The second question examines whether those similarities could be used to correct the unknown photometric variations in an unknown region from the known adjacent regions. A method is proposed, called Linear Correction Mapping, which is capable of providing an affirmative answer under the circumstances previously characterised. A training stage is required to determine the parameters of the model. The method for single camera scenarios is extended to cover non-overlapping multi-camera architectures. To this extent, only several image samples of the same object acquired by all of the cameras are required. Furthermore, both the light variations and the changes in the camera exposure settings are covered by correction mapping. Every image correction method is unsuccessful when the image of the object to be corrected is overexposed or the signal-to-noise ratio is very low. Thus, the third question refers to the control of the acquisition process to obtain an optimal exposure in uncontrolled light conditions. A Camera Exposure Control method is proposed that is capable of holding a suitable exposure provided that the light variations can be collected within the dynamic range of the camera. Each one of the proposed methods was evaluated individually. The methodology of the experiments consisted of first selecting some scenarios that cover the representative situations for which the methods are theoretically valid. Linear Correction Mapping was validated using three object re-identification applications (vehicles, faces and persons) based on the object colour distributions. Camera Exposure Control was proved in an outdoor parking scenario. In addition, several performance indicators were defined to objectively compare the results with other relevant state of the art correction and auto-exposure methods. The results of the evaluation demonstrated that the proposed methods outperform the compared ones in the most situations. Based on the obtained results, the answers to the above-described research questions are affirmative in limited circumstances, that is, the hypothesis of the forecasting, the correction based on it, and the auto exposure are feasible in the situations identified in the thesis, although they cannot be guaranteed in general. Furthermore, the presented work raises new questions and scientific challenges, which are highlighted as future research work.

Spatial and temporal variations of trace element distribution in soils and street dust of an industrial town in NW Spain: 15 years of study

Extensive spatial and temporal surveys, over 15 years, have been conducted in soil in urban parks and street dusts in one of the most polluted cities in western Europe, Avilés (NW Spain). The first survey was carried out in 1996, and since then monitoring has been undertaken every five years. Whilst the sampling site is a relatively small town, industrial activities (mainly the steel industry and Zn and Al metallurgy) and other less significant urban sources, such as traffic, strongly affect the load of heavy metals in the urban aerosol. Elemental tracers have been used to characterise the influence of these sources on the composition of soil and dust. Although PM10 has decreased over these years as a result of environmental measures undertaken in the city, some of the “industrial” elements still remain in concentrations of concern for example, up to 4.6% and 0.5% of Zn in dust and soil, respectively. Spatial trends in metals such as Zn and Cd clearly reflect sources from the processing industries. The concentrations of these elements across Europe have reduced over time, however the most recent results from Avilés revealed an upward trend in concentration for Zn, Cd, Hg and As. A risk assessment of the soil highlighted As as an element of concern since its cancer risk in adults was more than double the value above which regulatory agencies deem it to be unacceptable. If children were considered to be the receptors, then the risk nearly doubles from this element.

Study of PM10 and PM2.5 levels in three European cities: Analysis of intra and inter urban variations

In the present paper, 1-year PM10 and PM 2.5 data from roadside and urban background monitoring stations in Athens (Greece), Madrid (Spain) and London (UK) are analysed in relation to other air pollutants (NO,NO2,NOx,CO,O3 and SO2)and several meteorological parameters (wind velocity, temperature, relative humidity, precipitation, solar radiation and atmospheric pressure), in order to investigate the sources and factors affecting particulate pollution in large European cities. Principal component and regression analyses are therefore used to quantify the contribution of both combustion and non-combustion sources to the PM10 and PM 2.5 levels observed. The analysis reveals that the EU legislated PM 10 and PM2.5 limit values are frequently breached, forming a potential public health hazard in the areas studied. The seasonal variability patterns of particulates varies among cities and sites, with Athens and Madrid presenting higher PM10 concentrations during the warm period and suggesting the larger relative contribution of secondary and natural particles during hot and dry days. It is estimated that the contribution of non-combustion sources varies substantially among cities, sites and seasons and ranges between 38-67% and 40-62% in London, 26-50% and 20-62% in Athens, and 31-58% and 33-68% in Madrid, for both PM10 and PM 2.5. Higher contributions from non-combustion sources are found at urban background sites in all three cities, whereas in the traffic sites the seasonal differences are smaller. In addition, the non-combustion fraction of both particle metrics is higher during the warm season at all sites. On the whole, the analysis provides evidence of the substantial impact of non-combustion sources on local air quality in all three cities. While vehicular exhaust emissions carry a large part of the risk posed on human health by particle exposure, it is most likely that mitigation measures designed for their reduction will have a major effect only at traffic sites and additional measures will be necessary for the control of background levels. However, efforts in mitigation strategies should always focus on optimal health effects.

Determination of spectral variations by means of component cells useful for CPV rating and design

A methodology is presented to determine both the short-term and the long-term influence of the spectral variations on the performance of Multi-Junction (MJ) solar cells and Concentrating "This is the peer reviewed version of the following article: R. Núñez, C. Domínguez, S. Askins, M. Victoria, R. Herrero, I. Antón, and G. Sala, “Determination of spectral variations by means of component cells useful for CPV rating and design,” Prog. Photovolt: Res. Appl., 2015., which has been published in final form at http://onlinelibrary.wiley.com/doi/10.1002/pip.2715/full. This article may be used for non-commercial purposes in accordance with Wiley Terms and Conditions for Self-Archiving [http://olabout.wiley.com/WileyCDA/Section/id-820227.html#terms]." Photovoltaic (CPV) modules. Component cells with the same optical behavior as MJ solar cells are used to characterize the spectrum. A set of parameters, namely Spectral Matching Ratios (SMRs), is used to characterize spectrally a particular Direct Normal Irradiance (DNI) by comparison to the reference spectrum (AM1.5D-ASTM-G173-03). Furthermore, the spectrally corrected DNI for a given MJ solar cell technology is defined providing a way to estimate the losses associated to the spectral variations. The last section analyzes how the spectrum evolves throughout a year in a given place and the set of SMRs representative for that location are calculated. This information can be used to maximize the energy harvested by the MJ solar cell throughout the year. As an example, three years of data recorded in Madrid shows that losses lower than 5% are expected due to current mismatch for state-of-the-art MJ solar cells.

Fenología y capacidad de dispersión de Monochamus galloprovincialis (Olivier 1795) en la Península Ibérica = Phenology and dispersal ability of Monochamus galloprovincialis (Olivier 1795) at Iberian Peninsula

La aparición y avance de la enfermedad del marchitamiento del pino (Pine Wilt Desease, PWD), causada por Bursaphelenchus xylophilus (Nematoda; Aphelenchoididae), el nematodo de la madera del pino (NMP), en el suroeste de Europa, ha puesto de manifiesto la necesidad de estudiar la fenología y la dispersión de su único vector conocido en Europa, Monochamus galloprovincialis (Col., Cerambycidae). El análisis de 12 series de emergencias entre 2010 y 2014, registradas en Palencia, València y Teruel, con material procedente de diversos puntos de la península ibérica, demostró una alta variabilidad en la fenología de M. galloprovincialis y la divergencia térmica respecto de las poblaciones portuguesas. Para éstas, el establecimiento de los umbrales térmicos de desarrollo de las larvas post-dormantes del vector (12,2 y 33,5ºC) permitió la predicción de la emergencia mediana para la fecha en la que se acumulaban de 822 grados-día. Ninguna de las series analizadas en este trabajo necesitó de dichos grados-día estimados para la emergencia mediana. Asimismo, la emergencia se adelantó en las regiones más calurosas, mientras que se retrasó en las zonas más templadas. Más allá de la posible variabilidad entre poblaciones locales peninsulares, se detectaron indicios de que la diferencia en la acumulación de calor durante el otoño puede afectar el grado de maduración de las larvas invernantes, y su posterior patrón temporal de emergencia. Por último, también fueron observados comportamientos de protandria en las emergencias. Respecto a la fenología de su vuelo, entre los años 2010 y 2015, fueron ejecutados un total de 8 experimentos de captura de M. galloprovincialis mediante trampas cebadas con atrayentes en diferentes regiones (Castellón, Teruel, Segovia y Alicante) permitiendo el seguimiento del periodo de vuelo. Su análisis permitió constatar la disminución de las capturas y el acortamiento del periodo de vuelo con la altitud, el inicio del vuelo en el mes de mayo/junio a partir de los 14ºC de temperatura media diaria, la influencia de las altas temperaturas en la disminución de las capturas estivales (potencial causante de perfiles bimodales en las curvas de vuelo en las zonas menos frías), la evolución de la proporción de sexos a lo largo del periodo de vuelo (que muestra una mayor captura de hembras al inicio y de machos al final) y el comportamiento diurno y ligado a las altas temperaturas del vuelo circadiano del insecto. Dos redes de muestreo sistemático de insectos saproxílicos instaladas en la Comunitat Valencia (Red MUFFET, 15 parcelas, año 2013) y en Murcia (Red ESFP, 20 parcelas, años 2008-2010) permitieron el estudio de la comunidad de insectos relacionada con M. galloprovincialis. Cada una de las parcelas contaba con una trampa cebada con atrayentes y una estación meteorológica. El registro de más de 250 especies de coleópteros saproxílicos demostró el potencial que tiene el empleo de redes de trampas vigía para la detección temprana de organismos exóticos, además de permitir la caracterización y evaluación de las comunidades de entomofauna útil, representando una de las mejores herramientas de la gestión integrada de plagas. En este caso, la comunidad de saproxílicos estudiada mostró ser muy homogénea respecto a la variación ambiental de las zonas de muestreo, y que pese a las pequeñas variaciones entre las comunidades de los diferentes ecosistemas, el rol que M. galloprovincialis desempeña en ellas a lo largo de todo el gradiente estudiado es el mismo. Con todo, el análisis mediante redes de interacción mostró su relevancia ecológica al actuar de conector entre los diferentes niveles tróficos. Por último, un total de 12 experimentos de marcaje-liberación-recaptura desarrollados entre 2009 y 2012 en Castellón, Teruel, Valencia y Murcia permitieron evaluar el comportamiento dispersivo de M. galloprovincialis. Las detecciones mediante trampas cebadas de los insectos liberados se dieron por lo menos 8 días después de la emergencia. La abundancia de población pareció relacionada con la continuidad, la naturalización de la masa, y con la afección previa de incendios. La dispersión no estuvo influida por la dirección ni la intensidad de los vientos dominantes. La abundancia de material hospedante (en lo referente a las variables de masa y a los índices de competencia) influyó en la captura del insecto en paisajes fragmentados, aunque la ubicación de las trampas optimizó el número de capturas cuando se ubicaron en el límite de la masa y en zonas visibles. Por último también se constató que M. galloprovincialis posee suficiente capacidad de dispersión como para recorrer hasta 1500 m/día, llegando a alcanzar distancias máximas de 13600m o de 22100 m. ABSTRACT The detection and expansion of the Pine Wilt Desease (PWD), caused by Bursaphelenchus xylophilus (Nematoda; Aphelenchoididae), Pine Wood Nematode (PWN), in southwestern Europe since 1999, has triggered off the study of the phenology and the dispersion of its unique vector in the continent, Monochamus galloprovincialis (Coleoptera, Cerambycidae). The analysis of 12 emergence series between 2010 and 2014 registered in Palencia, Teruel and Valencia (Spain), registered from field colonized material collected at several locations of the Iberian Peninsula, showed a high variability in the emergence phenology of M. galloprovincialis. In addition, these patterns showed a very acute thermal divergence regarding a development model fitted earlier in Portugal. Such model forecasted the emergence of 50% of M. galloprovincialis individuals in the Setúbal Peninsula (Portugal) when an average of 822 degree-days (DD) were reached, based on the accumulation of heat from the 1st of March until emergence and lower and upper thresholds of 12.2 ºC and 33,5 °C respectively. In our results, all analyzed series needed less than 822 DD to complete the 50% of the emergence. Also, emergency occurred earlier in the hottest regions, while it was delayed in more temperate areas. Beyond the possible variability between local populations, the difference in the heat accumulation during the fall season may have affected the degree of maturation of overwintering larvae, and subsequently, the temporal pattern of M. galloprovincialis emergences. Therefore these results suggest the need to differentiate local management strategies for the PWN vector, depending on the location, and the climatic variables of each region. Finally, protandrous emergence patterns were observed for M. galloprovincialis in most of the studied data-sets. Regarding the flight phenology of M. galloprovincialis, a total of 8 trapping experiments were carried out in different regions of the Iberian Peninsula (Castellón, Teruel, Segovia and Alicante) between 2010 and 2015. The use of commercial lures and traps allowed monitoring of the flight period of M. galloprovincialis. The analyses of such curves, helped confirming different aspects. First, a decline in the number of catches and a shortening of the flight period was observed as the altitude increased. Flight period was recorded to start in May / June when the daily average temperature went over 14 ° C. A significant influence of high temperatures on the decrease of catches in the summer was found in many occasions, which frequently lead to a bimodal profile of the flight curves in warm areas. The evolution of sex ratio along the flight period shows a greater capture of females at the beginning of the period, and of males at the end. In addition, the circadian response of M. galloprovincialis to lured traps was described for the first time, concluding that the insect is diurnal and that such response is linked to high temperatures. Two networks of systematic sampling of saproxylic insects were installed in the Region of Valencia (Red MUFFET, 15 plots, 2013) and Murcia (Red ICPF, 20 plots, 2008-2010). These networks, intended to serve the double purpose of early-detection and long term monitoring of the saproxylic beetle assemblies, allowed the study of insect communities related to M. galloprovincialis. Each of the plots had a trap baited with attractants and a weather station. The registration of almost 300 species of saproxylic beetles demonstrated the potential use of such trapping networks for the early detection of exotic organisms, while at the same time allows the characterization and evaluation of useful entomological fauna communities, representing one of the best tools for the integrated pest management. In this particular case, the studied community of saproxylic beetles was very homogeneous with respect to environmental variation of the sampling areas, and despite small variations between communities of different ecosystems, the role that M. galloprovincialis apparently plays in them across the studied gradient seems to be the same. However, the analysis through food-webs showed the ecological significance of M. galloprovincialis as a connector between different trophic levels. Finally, 12 mark-release-recapture experiments were carried out between 2009 and 2012 in Castellón, Teruel, Valencia and Murcia (Spain) with the aim to describe the dispersive behavior of M. galloprovincialis as well as the stand and landscape characteristics that could influence its abundance and dispersal. No insects younger than 8 days were caught in lured traps. Population abundance estimates from mark-release-recapture data, seemed related to forest continuity, naturalization, and to prior presence of forest fires. On the other hand, M. galloprovincialis dispersal was not found to be significantly influenced by the direction and intensity of prevailing winds. The abundance of host material, very related to stand characteristics and spacing indexes, influenced the insect abundance in fragmented landscapes. In addition, the location of the traps optimized the number of catches when they were placed in the edge of the forest stands and in visible positions. Finally it was also found that M. galloprovincialis is able to fly up to 1500 m / day, reaching maximum distances of up to 13600 m or 22100 m.