Shadow Analysis of Soil Surface Roughness Compared to the Chain Set Method and Direct Measurement of Micro-relief.

Erosion potential and the effects of tillage can be evaluated from quantitative descriptions of soil surface roughness. The present study therefore aimed to fill the need for a reliable, low-cost and convenient method to measure that parameter. Based on the interpretation of micro-topographic shadows, this new procedure is primarily designed for use in the field after tillage. The principle underlying shadow analysis is the direct relationship between soil surface roughness and the shadows cast by soil structures under fixed sunlight conditions. The results obtained with this method were compared to the statistical indexes used to interpret field readings recorded by a pin meter. The tests were conducted on 4-m2 sandy loam and sandy clay loam plots divided into 1-m2 subplots tilled with three different tools: chisel, tiller and roller. The highly significant correlation between the statistical indexes and shadow analysis results obtained in the laboratory as well as in the field for all the soil?tool combinations proved that both variability (CV) and dispersion (SD) are accommodated by the new method. This procedure simplifies the interpretation of soil surface roughness and shortens the time involved in field operations by a factor ranging from 12 to 20.

High resolution system for nanoparticles hyperthermia efficiency evaluation

A system to evaluate nanoparticles efficiency in hyperthermia applications is presented. The method allows a direct measurement of the power dissipated by the nanoparticles through the determination of the first harmonic component of the in quadrature magnetic moment induced by the applied field. The magnetic moment is measured by using an induction method. To avoid errors and reduce the noise signal a double in phase demodulation technique is used. To test the system viability we have measured nanowires, nanoparticles and copper samples of different volumes to prove by comparing experimental and modeled results

Análisis y clasificación de maderas mediante técnicas no invasivas de baja energía

El estudio de materiales, especialmente biológicos, por medios no destructivos está adquiriendo una importancia creciente tanto en las aplicaciones científicas como industriales. Las ventajas económicas de los métodos no destructivos son múltiples. Existen numerosos procedimientos físicos capaces de extraer información detallada de las superficie de la madera con escaso o nulo tratamiento previo y mínima intrusión en el material. Entre los diversos métodos destacan las técnicas ópticas y las acústicas por su gran versatilidad, relativa sencillez y bajo coste. Esta tesis pretende establecer desde la aplicación de principios simples de física, de medición directa y superficial, a través del desarrollo de los algoritmos de decisión mas adecuados basados en la estadística, unas soluciones tecnológicas simples y en esencia, de coste mínimo, para su posible aplicación en la determinación de la especie y los defectos superficiales de la madera de cada muestra tratando, en la medida de lo posible, no alterar su geometría de trabajo. Los análisis desarrollados han sido los tres siguientes: El primer método óptico utiliza las propiedades de la luz dispersada por la superficie de la madera cuando es iluminada por un laser difuso. Esta dispersión produce un moteado luminoso (speckle) cuyas propiedades estadísticas permiten extraer propiedades muy precisas de la estructura tanto microscópica como macroscópica de la madera. El análisis de las propiedades espectrales de la luz laser dispersada genera ciertos patrones mas o menos regulares relacionados con la estructura anatómica, composición, procesado y textura superficial de la madera bajo estudio que ponen de manifiesto características del material o de la calidad de los procesos a los que ha sido sometido. El uso de este tipo de láseres implica también la posibilidad de realizar monitorizaciones de procesos industriales en tiempo real y a distancia sin interferir con otros sensores. La segunda técnica óptica que emplearemos hace uso del estudio estadístico y matemático de las propiedades de las imágenes digitales obtenidas de la superficie de la madera a través de un sistema de scanner de alta resolución. Después de aislar los detalles mas relevantes de las imágenes, diversos algoritmos de clasificacion automatica se encargan de generar bases de datos con las diversas especies de maderas a las que pertenecían las imágenes, junto con los márgenes de error de tales clasificaciones. Una parte fundamental de las herramientas de clasificacion se basa en el estudio preciso de las bandas de color de las diversas maderas. Finalmente, numerosas técnicas acústicas, tales como el análisis de pulsos por impacto acústico, permiten complementar y afinar los resultados obtenidos con los métodos ópticos descritos, identificando estructuras superficiales y profundas en la madera así como patologías o deformaciones, aspectos de especial utilidad en usos de la madera en estructuras. La utilidad de estas técnicas esta mas que demostrada en el campo industrial aun cuando su aplicación carece de la suficiente expansión debido a sus altos costes y falta de normalización de los procesos, lo cual hace que cada análisis no sea comparable con su teórico equivalente de mercado. En la actualidad gran parte de los esfuerzos de investigación tienden a dar por supuesto que la diferenciación entre especies es un mecanismo de reconocimiento propio del ser humano y concentran las tecnologías en la definición de parámetros físicos (módulos de elasticidad, conductividad eléctrica o acústica, etc.), utilizando aparatos muy costosos y en muchos casos complejos en su aplicación de campo. Abstract The study of materials, especially the biological ones, by non-destructive techniques is becoming increasingly important in both scientific and industrial applications. The economic advantages of non-destructive methods are multiple and clear due to the related costs and resources necessaries. There are many physical processes capable of extracting detailed information on the wood surface with little or no previous treatment and minimal intrusion into the material. Among the various methods stand out acoustic and optical techniques for their great versatility, relative simplicity and low cost. This thesis aims to establish from the application of simple principles of physics, surface direct measurement and through the development of the more appropriate decision algorithms based on statistics, a simple technological solutions with the minimum cost for possible application in determining the species and the wood surface defects of each sample. Looking for a reasonable accuracy without altering their work-location or properties is the main objetive. There are three different work lines: Empirical characterization of wood surfaces by means of iterative autocorrelation of laser speckle patterns: A simple and inexpensive method for the qualitative characterization of wood surfaces is presented. it is based on the iterative autocorrelation of laser speckle patterns produced by diffuse laser illumination of the wood surfaces. The method exploits the high spatial frequency content of speckle images. A similar approach with raw conventional photographs taken with ordinary light would be very difficult. A few iterations of the algorithm are necessary, typically three or four, in order to visualize the most important periodic features of the surface. The processed patterns help in the study of surface parameters, to design new scattering models and to classify the wood species. Fractal-based image enhancement techniques inspired by differential interference contrast microscopy: Differential interference contrast microscopy is a very powerful optical technique for microscopic imaging. Inspired by the physics of this type of microscope, we have developed a series of image processing algorithms aimed at the magnification, noise reduction, contrast enhancement and tissue analysis of biological samples. These algorithms use fractal convolution schemes which provide fast and accurate results with a performance comparable to the best present image enhancement algorithms. These techniques can be used as post processing tools for advanced microscopy or as a means to improve the performance of less expensive visualization instruments. Several examples of the use of these algorithms to visualize microscopic images of raw pine wood samples with a simple desktop scanner are provided. Wood species identification using stress-wave analysis in the audible range: Stress-wave analysis is a powerful and flexible technique to study mechanical properties of many materials. We present a simple technique to obtain information about the species of wood samples using stress-wave sounds in the audible range generated by collision with a small pendulum. Stress-wave analysis has been used for flaw detection and quality control for decades, but its use for material identification and classification is less cited in the literature. Accurate wood species identification is a time consuming task for highly trained human experts. For this reason, the development of cost effective techniques for automatic wood classification is a desirable goal. Our proposed approach is fully non-invasive and non-destructive, reducing significantly the cost and complexity of the identification and classification process.

Monte-Carlo dosimetry on a realistic cell monolayer geometry exposed to alpha particles

The energy and specific energy absorbed in the main cell compartments (nucleus and cytoplasm) in typical radiobiology experiments are usually estimated by calculations as they are not accessible for a direct measurement. In most of the work, the cell geometry is modelled using the combination of simple mathematical volumes. We propose a method based on high resolution confocal imaging and ion beam analysis (IBA) in order to import realistic cell nuclei geometries in Monte-Carlo simulations and thus take into account the variety of different geometries encountered in a typical cell population. Seventy-six cell nuclei have been imaged using confocal microscopy and their chemical composition has been measured using IBA. A cellular phantom was created from these data using the ImageJ image analysis software and imported in the Geant4 Monte-Carlo simulation toolkit. Total energy and specific energy distributions in the 76 cell nuclei have been calculated for two types of irradiation protocols: a 3 MeV alpha particle microbeam used for targeted irradiation and a 239Pu alpha source used for large angle random irradiation. Qualitative images of the energy deposited along the particle tracks have been produced and show good agreement with images of DNA double strand break signalling proteins obtained experimentally. The methodology presented in this paper provides microdosimetric quantities calculated from realistic cellular volumes. It is based on open-source oriented software that is publicly available.

Auscultación de presas de hormigón con láser escáner terrestre y modelización de las deformaciones del paramento

Se está produciendo en la geodesia un cambio de paradigma en la concepción de los modelos digitales del terreno, pasando de diseñar el modelo con el menor número de puntos posibles a hacerlo con cientos de miles o millones de puntos. Este cambio ha sido consecuencia de la introducción de nuevas tecnologías como el escáner láser, la interferometría radar y el tratamiento de imágenes. La rápida aceptación de estas nuevas tecnologías se debe principalmente a la gran velocidad en la toma de datos, a la accesibilidad por no precisar de prisma y al alto grado de detalle de los modelos. Los métodos topográficos clásicos se basan en medidas discretas de puntos que considerados en su conjunto forman un modelo; su precisión se deriva de la precisión en la toma singular de estos puntos. La tecnología láser escáner terrestre (TLS) supone una aproximación diferente para la generación del modelo del objeto observado. Las nubes de puntos, producto del escaneo con TLS, pasan a ser tratadas en su conjunto mediante análisis de áreas, de forma que ahora el modelo final no es el resultado de una agregación de puntos sino la de la mejor superficie que se adapta a las nubes de puntos. Al comparar precisiones en la captura de puntos singulares realizados con métodos taquimétricos y equipos TLS la inferioridad de estos últimos es clara; sin embargo es en el tratamiento de las nubes de puntos, con los métodos de análisis basados en áreas, se han obtenido precisiones aceptables y se ha podido considerar plenamente la incorporación de esta tecnología en estudios de deformaciones y movimientos de estructuras. Entre las aplicaciones del TLS destacan las de registro del patrimonio, registro de las fases en la construcción de plantas industriales y estructuras, atestados de accidentes y monitorización de movimientos del terreno y deformaciones de estructuras. En la auscultación de presas, comparado con la monitorización de puntos concretos dentro, en coronación o en el paramento de la presa, disponer de un modelo continuo del paramento aguas abajo de la presa abre la posibilidad de introducir los métodos de análisis de deformaciones de superficies y la creación de modelos de comportamiento que mejoren la comprensión y previsión de sus movimientos. No obstante, la aplicación de la tecnología TLS en la auscultación de presas debe considerarse como un método complementario a los existentes. Mientras que los péndulos y la reciente técnica basada en el sistema de posicionamiento global diferencial (DGPS) dan una información continua de los movimientos de determinados puntos de la presa, el TLS permite ver la evolución estacional y detectar posibles zonas problemáticas en todo el paramento. En este trabajo se analizan las características de la tecnología TLS y los parámetros que intervienen en la precisión final de los escaneos. Se constata la necesidad de utilizar equipos basados en la medida directa del tiempo de vuelo, también llamados pulsados, para distancias entre 100 m y 300 m Se estudia la aplicación del TLS a la modelización de estructuras y paramentos verticales. Se analizan los factores que influyen en la precisión final, como el registro de nubes, tipo de dianas y el efecto conjunto del ángulo y la distancia de escaneo. Finalmente, se hace una comparación de los movimientos dados por los péndulos directos de una presa con los obtenidos del análisis de las nubes de puntos correspondientes a varias campañas de escaneos de la misma presa. Se propone y valida el empleo de gráficos patrón para relacionar las variables precisión o exactitud con los factores distancia y ángulo de escaneo en el diseño de trabajos de campo. Se expone su aplicación en la preparación del trabajo de campo para la realización de una campaña de escaneos dirigida al control de movimientos de una presa y se realizan recomendaciones para la aplicación de la técnica TLS a grandes estructuras. Se ha elaborado el gráfico patrón de un equipo TLS concreto de alcance medio. Para ello se hicieron dos ensayos de campo en condiciones reales de trabajo, realizando escaneos en todo el rango de distancias y ángulos de escaneo del equipo. Se analizan dos métodos para obtener la precisión en la modelización de paramentos y la detección de movimientos de estos: el método del “plano de mejor ajuste” y el método de la “deformación simulada”. Por último, se presentan los resultados de la comparación de los movimientos estacionales de una presa arco-gravedad entre los registrados con los péndulos directos y los obtenidos a partir de los escaneos realizados con un TLS. Los resultados muestran diferencias de milímetros, siendo el mejor de ellos del orden de un milímetro. Se explica la metodología utilizada y se hacen consideraciones respecto a la densidad de puntos de las nubes y al tamaño de las mallas de triángulos. A shift of paradigm in the conception of the survey digital models is taking place in geodesy, moving from designing a model with the fewer possible number of points to models of hundreds of thousand or million points. This change has happened because of the introduction of new technologies like the laser scanner, the interferometry radar and the processing of images. The fast acceptance of these new technologies has been due mainly to the great speed getting the data, to the accessibility as reflectorless technique, and to the high degree of detail of the models. Classic survey methods are based on discreet measures of points that, considered them as a whole, form a model; the precision of the model is then derived from the precision measuring the single points. The terrestrial laser scanner (TLS) technology supposes a different approach to the model generation of the observed object. Point cloud, the result of a TLS scan, must be treated as a whole, by means of area-based analysis; so, the final model is not an aggregation of points but the one resulting from the best surface that fits with the point cloud. Comparing precisions between the one resulting from the capture of singular points made with tachometric measurement methods and with TLS equipment, the inferiority of this last one is clear; but it is in the treatment of the point clouds, using area-based analysis methods, when acceptable precisions have been obtained and it has been possible to consider the incorporation of this technology for monitoring structures deformations. Among TLS applications it have to be emphasized those of registry of the cultural heritage, stages registry during construction of industrial plants and structures, police statement of accidents and monitorization of land movements and structures deformations. Compared with the classical dam monitoring, approach based on the registry of a set of points, the fact having a continuous model of the downstream face allows the possibility of introducing deformation analysis methods and behavior models that would improve the understanding and forecast of dam movements. However, the application of TLS technology for dam monitoring must be considered like a complementary method with the existing ones. Pendulums and recently the differential global positioning system (DGPS) give a continuous information of the movements of certain points of the dam, whereas TLS allows following its seasonal evolution and to detect damaged zones of the dam. A review of the TLS technology characteristics and the factors affecting the final precision of the scanning data is done. It is stated the need of selecting TLS based on the direct time of flight method, also called pulsed, for scanning distances between 100m and 300m. Modelling of structures and vertical walls is studied. Factors that influence in the final precision, like the registry of point clouds, target types, and the combined effect of scanning distance and angle of incidence are analyzed. Finally, a comparison among the movements given by the direct pendulums of a dam and the ones obtained from the analysis of point clouds is done. A new approach to obtain a complete map-type plot of the precisions of TLS equipment based on the direct measurement of time of flight method at midrange distances is presented. Test were developed in field-like conditions, similar to dam monitoring and other civil engineering works. Taking advantage of graphic semiological techniques, a “distance - angle of incidence” map based was designed and evaluated for field-like conditions. A map-type plot was designed combining isolines with sized and grey scale points, proportional to the precision values they represent. Precisions under different field conditions were compared with specifications. For this purpose, point clouds were evaluated under two approaches: the standar "plane-of-best-fit" and the proposed "simulated deformation”, that showed improved performance. These results lead to a discussion and recommendations about optimal TLS operation in civil engineering works. Finally, results of the comparison of seasonal movements of an arc-gravity dam between the registered by the direct pendulums ant the obtained from the TLS scans, are shown. The results show differences of millimeters, being the best around one millimeter. The used methodology is explained and considerations with respect to the point cloud density and to the size of triangular meshes are done.

On-line measurement of soil properties without direct spectral response in near infrared spectral range

So far, the majority of reports on on-line measurement considered soil properties with direct spectral responses in near infrared spectroscopy (NIRS). This work reports on the results of on-line measurement of soil properties with indirect spectral responses, e.g. pH, cation exchange capacity (CEC), exchangeable calcium (Caex) and exchangeable magnesium (Mgex) in one field in Bedfordshire in the UK. The on-line sensor consisted of a subsoiler coupled with an AgroSpec mobile, fibre type, visible and near infrared (vis–NIR) spectrophotometer (tec5 Technology for Spectroscopy, Germany), with a measurement range 305–2200 nm to acquire soil spectra in diffuse reflectance mode. General calibration models for the studied soil properties were developed with a partial least squares regression (PLSR) with one-leave-out cross validation, using spectra measured under non-mobile laboratory conditions of 160 soil samples collected from different fields in four farms in Europe, namely, Czech Republic, Denmark, Netherland and UK. A group of 25 samples independent from the calibration set was used as independent validation set. Higher accuracy was obtained for laboratory scanning as compared to on-line scanning of the 25 independent samples. The prediction accuracy for the laboratory and on-line measurements was classified as excellent/very good for pH (RPD = 2.69 and 2.14 and r2 = 0.86 and 0.78, respectively), and moderately good for CEC (RPD = 1.77 and 1.61 and r2 = 0.68 and 0.62, respectively) and Mgex (RPD = 1.72 and 1.49 and r2 = 0.66 and 0.67, respectively). For Caex, very good accuracy was calculated for laboratory method (RPD = 2.19 and r2 = 0.86), as compared to the poor accuracy reported for the on-line method (RPD = 1.30 and r2 = 0.61). The ability of collecting large number of data points per field area (about 12,800 point per 21 ha) and the simultaneous analysis of several soil properties without direct spectral response in the NIR range at relatively high operational speed and appreciable accuracy, encourage the recommendation of the on-line measurement system for site specific fertilisation.

Influence of loudspeaker directivity and measurement geometry on direct acoustic levels over façades for acoustic insulation tests with the International Standard ISO 140-5

The International Standard ISO 140-5 on field measurements of airborne sound insulation of façades establishes that the directivity of the measurement loudspeaker should be such that the variation in the local direct sound pressure level (ΔSPL) on the sample is ΔSPL < 5 dB (or ΔSPL < 10 dB for large façades). This condition is usually not very easy to accomplish nor is it easy to verify whether the loudspeaker produces such a uniform level. Direct sound pressure levels on the ISO standard façade essentially depend on the distance and directivity of the loudspeaker used. This paper presents a comprehensive analysis of the test geometry for measuring sound insulation and explains how the loudspeaker directivity, combined with distance, affects the acoustic level distribution on the façade. The first sections of the paper are focused on analysing the measurement geometry and its influence on the direct acoustic level variations on the façade. The most favourable and least favourable positions to minimise these direct acoustic level differences are found, and the angles covered by the façade in the reference system of the loudspeaker are also determined. Then, the maximum dimensions of the façade that meet the conditions of the ISO 140-5 standard are obtained for the ideal omnidirectional sound source and the piston radiating in an infinite baffle, which is chosen as the typical radiation pattern for loudspeakers. Finally, a complete study of the behaviour of different loudspeaker radiation models (such as those usually utilised in the ISO 140-5 measurements) is performed, comparing their radiation maps on the façade for searching their maximum dimensions and the most appropriate radiation configurations.

On-site measurement of limiting subcell in multijunction solar devices

It is well known that the response of any photovoltaic solar cell is dependent on the spectral characteristics of the incident radiation. This dependency is crucial in the output characteristics of a multijunction (MJ) cell where the spectral composition of the radiation determines the overall photocurrent produced, as either the top or the middle subcell will be limiting its response. The current mismatching between top and middle subcell is translated into energy losses, affecting the yield of the system. For research and commercial purposes it is interesting to measure accurately the incident solar radiation on a MJ cell, in terms of its spectral composition. This measurement will allows us to determine the photocurrent generated in each band of the multijunction device. Nowadays, the only way of measuring the photocurrent generated by each subcell is done with isotype cells or with spectroradiometers but there is no device capable of directly measuring each subcell photocurrent. In this paper it is described a device based on a commercial multijunction solar cell that is capable of measuring the direct irradiance for the top and middle bands thus it offers information of the limiting subcell (top or middle) in outdoors conditions.