Importance of canopy porosity into vineyard and the relationship with the grape maturity. Digital estimation method

In warm and dry climates, the use of porous systems should be required in order to allow a better leaf distribution inside the plant, causing more space in the clusters area and enhancing determined physiological processes so in the leaf (photosynthesis, v entilation, transpiration) as in berry (growth and maturation). Plant geometry indexes, yield and must composition have been studied in three different systems: sprawl with 12 shoots/m (S1); sprawl system with 18 shoots/m (S2) and vertical positioned syste m or VSP with 12 shoots/m (VSP1). Total leaf area increases as the crop load does, whoever surface area depends on to two factors: crop load and the training system (VSP vs. sprawl), which can provide differences in leaf exposure efficiencies. The main objective of this study was to validate digital photography measurements used to compare porosity differences among treatments and, as they affect plant microclimate and, therefore, yield and berry quality. Also, all previous studied indexes (LAI, SA, SFEr) tended to overestimate the relationship between exposed leaf surface and porosity of each treatment, but the use of digital method proved to be an effective tool in order to assess canopy porosity. Results showed that not positioned and free systems (sprawl) scored between 25- 50% more porosity in the clusters area than the fixed vertical system (VSP), which resulted in a better plant microclimate for test conditions, mainly by improving the exposure of internal clusters and internal canopy ventilation. On the other hand, higher crop load treatment (S2) showed a real increase in yield (16%) without any relevant change into must composition, even improving total anthocyanin content into berry during ripening

Importance of canopy porosity into vineyard and the relationship with the grape maturity. Digital estimation method

In warm and dry climates, the use of porous systems should be required in order to allow a better leaf distribution inside the plant, causing more space in the clusters area and enhancing determined physiological processes so in the leaf (photosynthesis, ventilation, transpiration) as in berry (growth and maturation). Plant geometry indexes, yield and must composition have been studied in three different systems: sprawl with 12 shoots/m (S1); sprawl system with 18 shoots/m (S2) and vertical positioned system or VSP with 12 shoots/m (VSP1). Total leaf area increases as the crop load does, whoever surface area depends on to two factors: crop load and the training system (VSP vs . sprawl), which can provide differences in leaf exposure efficiencies. The main objective of this study was to validate digital photography measurements used to compare porosity differences among treatments and, as they affect plant microclimate and, therefore, yield and berry quality. Also, all previous studied indexes (LAI, SA, SFEr) tended to overestimate the relationship between exposed leaf surface and porosity of each treatment, but the use of digital method proved to be an effective tool in order to assess canopy porosity. Results showed that not positioned and free systems (sprawl) scored between 25 - 50% more porosity in the clusters area than the fixed vertical system (VSP), which resulted in a better plant microclimate for test conditions, mainly by improving the exposure of internal clusters and internal canopy ventilation. On the other hand, higher crop load treatment (S2) showed a real increase in yield (16%) without any relevant change into must composition, even improving total anthocyanin content into berry during ripening

Estudio de las formas de aplicación de la fotografía sobre los materiales pétreos para la arquitectura = Study of photography application methods over architectural stony materials

Desde que el Hombre era morador de las cavernas ha sido manifiesto su deseo innato por grabar y reproducir "instantáneas con las que perpetuarse o sobre las que mirarse ". La aparición y desarrollo de la fotografía como medio para poder captar y fijar "la imagen directa de la realidad circundante " pronto se convierte en un nuevo lenguaje estético y poético que permite al artista la interpretación y reflexión de lo observado. Se imprime a la imagen el carácter de la mirada del fotógrafo, estableciendo un diálogo conceptual con el juego de luces. La presente Tesis plantea la creación de una nueva piel de arquitectura mediante la impresión fotográfica sobre materiales pétreos. La búsqueda de la expresividad de los materiales como soporte de expresión artística implica un cambio de escala al trasladar la instantánea fotográfica a la arquitectura y la aplicación de un nuevo soporte al imprimir la fotografía sobre materiales arquitectónicos. Se justifica la elección del dispositivo láser CO2 como sistema de impresión fotográfica sobre los materiales pétreos arquitectónicos, como la técnica que permite la unión física de la imagen y el proyecto arquitectónico, generando un valor añadido a través del arte de la fotografía. Se justifica la elección de los materiales investigados, Silestone® Blanco Zeus y GRC® con TX Active® Aria, de forma que la investigación de esta nueva piel de arquitectura abarca tanto la envolvente del edificio como su volumen interior, permitiendo cerrar el círculo arquitectónico "in&out" y dota al proyecto arquitectónico de un valor añadido al introducir conceptos sostenibles de carácter estético y medioambiental. Se realiza una consulta a las empresas del sector arquitectónico relacionadas directamente con la producción y distribución de los materiales Silestone® y GRC®, así como a las empresas especializadas en sistemas de impresión fotográfica sobre materiales, acerca del estado del arte. Se recorre la Historia de la fotografía desde sus orígenes hasta el desarrollo de la era digital y se analiza su condición artística. Se recopilan los sistemas de impresión fotográfica que han evolucionado en paralelo con los dispositivos de captura de la instantánea fotográfica y se describe en profundidad el sistema de impresión fotográfica mediante dispositivo láser CO2. Se describen los procesos de fabricación, las características técnicas, cualidades y aplicaciones de los materiales pétreos arquitectónicos Silestone® Blanco Zeus y GRC® con TX Active® Aria. Se explica la técnica utilizada para la captación de la imagen fotográfica, su justificación artística y su proceso de impresión mediante dispositivo láser CO2 bajo diferentes parámetros sobre muestras de los materiales arquitectónicos investigados. Se comprueba la viabilidad de desarrollo de la nueva piel de arquitectura sobre Silestone® Blanco Zeus y GRC® con TX Active® Aria sometiendo a las piezas impresas bajo diferentes parámetros a tres ensayos de laboratorio. En cada uno de ellos se concreta el objetivo y procedimiento del ensayo, la enumeración de las muestras ensayadas y los parámetros bajo los que han sido impresas, el análisis de los resultados del ensayo y las conclusiones del ensayo. Ensayo de amplitud térmica. Se determina el grado de afectación de las imágenes impresas bajo la acción de contrastes térmicos. Series de muestras de Silestone® Blanco Zeus y GRC® con TX Active® Aria impresas con láser CO2 se someten a ciclos de contraste frío-calor de 12 horas de duración para una amplitud térmica total de 102°C. Se realiza una toma sistemática de fotografías microscópicas con lupa de aumento de cada pieza antes y después de los ciclos frío-calor y la observación de las transformaciones que experimentan los materiales bajo la acción del láser CO2. Ensayo de exposición a la acción de la radiación ultravioleta (UV). Se determina el grado de afectación de las imágenes impresas al activar la capacidad autolimpiante de partículas orgánicas. Una serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a ciclos de exposición de radiación ultravioleta de 26 horas de duración. Se somete la serie a un procedimiento de activación del aditivo TX Active®. Se simula la contaminación orgánica mediante la aplicación controlada de Rodamina B, tinte orgánico, y se simula la radiación UV mediante el empleo de una bombilla de emisión de rayos ultravioleta. Se realiza una toma sistemática de fotografías macroscópicas de la serie de muestras ensayadas: antes de aplicación de la Rodamina B, momento 00:00h, momento 04:00h y momento 26:00h del ensayo. Se procede a la descarga y análisis del histograma de las fotografías como registro de la actividad fotocatalítica. Ensayo de la capacidad autodescontaminante del GRC® con TX Active® impreso con láser CO2. Se comprueba si la capacidad autodescontaminante del GRC® con TX Active® se ve alterada como consecuencia de la impresión de la imagen fotográfica impresa con láser CO2. Serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a test de capacidad autodescontaminante: atmósfera controlada y contaminada con óxidos de nitrógeno en los que se coloca cada pieza ensayada bajo la acción de una lámpara de emisión de radiación ultravioleta (UV). Se registra la actividad fotocatalítica en base a la variación de concentración de óxido de nitrógeno. Se recopila el análisis e interpretación de los resultados de los ensayos de laboratorio y se elaboran las conclusiones generales de la investigación. Se sintetizan las futuras líneas de investigación que, a partir de las investigaciones realizadas y de sus conclusiones generales, podrían desarrollarse en el ámbito de la impresión fotográfica sobre materiales arquitectónicos. Se describe el rendimiento tecnológico y artístico generado por las investigaciones previas que han dado origen y desarrollo a la Tesis Doctoral. ABSTRACT Since ancient time, humanity has been driven by an innate wish to reproduce and engrave "snapshots that could help to perpetúate or to look at one self". Photography's birth and its development as a mean to capture and fix "the direct image of the surrounding reality" quickly becomes a new aesthetical and poetical language allowing the artist to interpret and think over what has been observed. The photographer's eye is imprinted onto the image, and so the conceptual dialogue between the artist and the light beams begins. The current thesis suggests the creation of a new architectural skin through photography imprinting over stony materials. The search for material's expressiveness as a medium of artistic expression involves a change of scale as it transfers photographic snapshot into architecture and the use of a new photographic printing support over architectural materials. CO2 laser is the chosen printing system for this technique as it allows the physical union of the image and the architectonic project, generating an added value through the art of photography. The researched materials selected were Silestone®, Blanco Zeus and GRC® with TX Active® Aria. This new architectural skin contains the building surrounding as well as its interior volume, closing the architectonic "in & out" circle and adding a value to the project by introducing aesthetical and environmental sustainable concepts. Architecture companies related to the production and distribution of materials like Silestone® and GRC®, as well as companies specialized in photography printing over materials were consulted to obtain a State of the Art. A thorough analysis of photography's History from its origins to the digital era development was made and its artistic condition was studied in this thesis. In this study the author also makes a compilation of several photographic printing systems that evolved together with photographic snapshot devices. The CO2 laser-based photographic printing system is also described in depth. Regarding stony materials of architecture like Silestone®, Blanco Zeus and GRC® with TX Active® Aria, the present study also describes their manufacture processes as well as technical features, quality and application. There is also an explanation about the technique to capture the photographic image, its artistic justification and its CO2 laser-based printing system over the researched materials under different parameters. We also tested the feasibility of this new architectural skin over Silestone® Blanco Zeus and GRC® with TX Active® Aria. The pieces were tested under different parameters in three laboratory trials. Each trial comprises of an explanation of its objective and its process, the samples were numbered and the printing parameters were specified. Finally, with the analysis of the results some conclusions were drawn. In the thermal amplitude trial we tried to determine how printed images were affected as a result of the action of thermal contrasts. Series of samples of Silestone® Blanco Zeus and GRC® with TX Active® Aria printed with CO2 laser were subjected to several 12h warm-cold cycles for thermal total amplitude of 102oc. Each sample was captured systematically with microscopic enhanced lenses before and after cold-warm cycles. The changes experienced by these materials under the effect of CO2 laser were observed and recorded. Trial regarding the Ultraviolet Radiation (UR) effect on images. We determined to which extent printed images were affected once the self-cleaning organic particles were activated. This time GRC® with TX Active® Aria samples printed with CO2 laser were exposed to a 26h UR cycle. The samples were subjected to the activation of TX Active® additive. Through the controlled application of Rodamine B and organic dye we were able to simulate the organic contamination process. UR was simulated using an ultraviolet beam emission bulb. A systematic capture of macroscopic pictures of the tested sample series was performed at different time points: before Rodamine B application, at moment 00:00h, moment 04:00h and moment 26:00h of the trial. Picture's histogram was downloaded and analyzed as a log of photocatalytic activity. Trial regarding the self-decontaminating ability of GRC® with TX Active® printed with CO2 laser. We tested if this self-decontaminating ability is altered as a result of CO2 laser printed image. GRC® with TX Active® Aria samples printed with CO2 laser, were subject to self-decontaminating ability tests with controlled and nitrogen oxide contaminated atmosphere. Each piece was put under the action of an UR emission lamp. Photocatalytic activity was recorded according to the variation in nitrogen oxide concentration. The results of the trial and their interpretation as well as the general conclusions of the research are also compiled in the present study. Study conclusions enable to draw future research lines of potential applications of photographic printing over architecture materials. Previous research generated an artistic and technological outcome that led to the development of this doctoral thesis.