An investigation of the performance of a new Mechanical thrombectomy device using Bond Graph modelling: application to the extraction of blood clots in the middle cerebral artery

A number of thrombectomy devices using a variety of methods have now been developed to facilitate clot removal. We present research involving one such experimental device recently developed in the UK, called a ‘GP’ Thrombus Aspiration Device (GPTAD). This device has the potential to bring about the extraction of a thrombus. Although the device is at a relatively early stage of development, the results look encouraging. In this work, we present an analysis and modeling of the GPTAD by means of the bond graph technique; it seems to be a highly effective method of simulating the device under a variety of conditions. Such modeling is useful in optimizing the GPTAD and predicting the result of clot extraction. The aim of this simulation model is to obtain the minimum pressure necessary to extract the clot and to verify that both the pressure and the time required to complete the clot extraction are realistic for use in clinical situations, and are consistent with any experimentally obtained data. We therefore consider aspects of rheology and mechanics in our modeling.

Performance of a transmutation advanced device for sustainable energy application

Preliminary studies have been performed to design a device for nuclear waste transmutation and hydrogen generation based on a gas-cooled pebble bed accelerator driven system, TADSEA (Transmutation Advanced Device for Sustainable Energy Application). In previous studies we have addressed the viability of an ADS Transmutation device that uses as fuel wastes from the existing LWR power plants, encapsulated in graphite in the form of pebble beds, cooled by helium which enables high temperatures (in the order of 1200 K), to generate hydrogen from water either by high temperature electrolysis or by thermochemical cycles. For designing this device several configurations were studied, including several reflectors thickness, to achieve the desired parameters, the transmutation of nuclear waste and the production of 100 MW of thermal power. In this paper new studies performed on deep burn in-core fuel management strategy for LWR waste are presented. The fuel cycle on TADSEA device has been analyzed based on both: driven and transmutation fuel that had been proposed by the General Atomic design of a gas turbine-modular helium reactor. The transmutation results of the three fuel management strategies, using driven, transmutation and standard LWR spent fuel were compared, and several parameters describing the neutron performance of TADSEA nuclear core as the fuel and moderator temperature reactivity coefficients and transmutation chain, are also presented

Applicability of the GP Device to the Circle of Willis Arteries by Using a Mathematical Model

According to the World Health Organization, 15 million people suffer stroke worldwide each year, of these, 5 million die and 5 million are permanently disabled. Stroke is therefore a major cause of mortality world-wide. The majority of strokes are caused by a blood clot that occludes an artery in the brain, and although thrombolytic agents such as Alteplase are used to dissolve clots that arise in the arteries of the brain, there are limitations on the use of these thrombolytic agents. However over the past decade, other methods of treatment have been developed which include Thrombectomy Devices e.g. the 'GP' Thrombus Aspiration Device ('GP' TAD). Such devices may be used as an alternative to thrombolytics or in conjunction with them to extract blood clots in arteries such as the middle cerebral artery of the midbrain brain, and the posterior inferior cerebellar artery (PICA) of the posterior aspect of the brain. In this paper, we mathematically model the removal of blood clots using the 'GP' TAD from selected arteries of the brain where blood clots may arise taking into account factors such as the resistances, compliances and inertances effects. Such mathematical modelling may have potential uses in predicting the pressures necessary to extract blood clots of given lengths, and masses from arteries in the Circle of Willis - posterior circulation of the brain

Analysis and design of a thrombectomy device by using simulation techniques

Purpose: In this work, we present the analysis, design and optimization of one experimental device recently developed in the UK, called the 'GP' Thrombus Aspiration Device (GPTAD). This device has been designed to remove blood clots without the need to make contact with the clot itself thereby potentially reducing the risk of problems such as downstream embolisation. Method: To obtain the minimum pressure necessary to extract the clot and to optimize the device, we have simulated the performance of the GPTAD analysing the resistances, compliances and inertances effects. We model a range of diameters for the GPTAD considering different forces of adhesion of the blood clot to the artery wall, and different lengths of blood clot. In each case we determine the optimum pressure required to extract the blood clot from the artery using the GPTAD, which is attached at its proximal end to a suction pump. Result: We then compare the results of our mathematical modelling to measurements made in laboratory using plastic tube models of arteries of comparable diameter. We use abattoir porcine blood clots that are extracted using the GPTAD. The suction pressures required for such clot extraction in the plastic tube models compare favourably with those predicted by the mathematical modelling. Discussion & Conclusion: We conclude therefore that the mathematical modelling is a useful technique in predicting the performance of the GPTAD and may potentially be used in optimising the design of the device.

Simulation of a mechanical thrombectomy device based in the use of self-expandable stents for the blood clots extraction

Recently, we have presented some studies concerning the analysis, design and optimization of one experimental device developed in the UK - GPTAD - which has been designed to remove blood clots without the need to make contact with the clot itself, thereby potentially reducing the risk of problems such as downstream embolisation. Based on the idea of a modification of the previous device, in this work, we present a model based in the use of stents like the SolitaireTM FR, which is in contact with the clot itself. In the case of such devices, the stent is self-expandable and the extraction of the blood clot is faciliatated by the stent, which must be inside the clot. Such stents are generally inserted in position by using the guidewire inserted into the catheter. This type of modeling could potentially be useful in showing how the blood clot is moved by the various different forces involved. The modelling has been undertaken by analyzing the resistances, compliances and inertances effects. We model an artery and blood clot for range of forces for the guidewire. In each case we determine the interaction between blood clot, stent and artery.

A portable NIR device for the optical supervision of milk coagulation process

The coagulation of milk is the fundamental process in cheese-making, based on a gel formation as consequence of physicochemical changes taking place in the casein micelles, the monitoring the whole process of milk curd formation is a constant preoccupation for dairy researchers and cheese companies (Lagaude et al., 2004). In addition to advances in composition-based applications of near infrared spectroscopy (NIRS), innovative uses of this technology are pursuing dynamic applications that show promise, especially in regard to tracking a sample in situ during food processing (Bock and Connelly, 2008). In this way the literature describes cheese making process applications of NIRS for curd cutting time determination, which conclude that NIRS would be a suitable method of monitoring milk coagulation, as shown i.e. the works published by Fagan et al. (Fagan et al., 2008; Fagan et al., 2007), based in the use of the commercial CoAguLite probe (with a LED at 880nm and a photodetector for light reflectance detection).

Kinematic analysis of a novel 2-d.o.f. orientation device

This paper presents the development of a new parallel robot designed for helping with bone milling surgeries. The robot is a small modular wrist with 2 active degrees of freedom, and it is proposed to be used as an orientation device located at the end of a robotic arm designed for bone milling processes. A generic kinematic geometry is proposed for this device. This first article shows the developments on the workspace optimization and the analysis of the force field required to complete a reconstruction of the inferior jawbone. The singularities of the mechanism are analyzed, and the actuator selection is justified with the torque requirements and the study of the force space. The results obtained by the simulations allow building a first prototype using linear motors. Bone milling experiment video is shown as additional material.

Probabilistic reasoning with a bayesian DNA device based on strand displacement

We present a computing model based on the DNA strand displacement technique which performs Bayesian inference. The model will take single stranded DNA as input data, representing the presence or absence of a specific molecular signal (evidence). The program logic encodes the prior probability of a disease and the conditional probability of a signal given the disease playing with a set of different DNA complexes and their ratios. When the input and program molecules interact, they release a different pair of single stranded DNA species whose relative proportion represents the application of Bayes? Law: the conditional probability of the disease given the signal. The models presented in this paper can empower the application of probabilistic reasoning in genetic diagnosis in vitro.

2D tunable graded index prism beam steering device based on nematic liquid crystals

Liquid crystal devices are being used in many non-display applications in order to construct small devices controlled by low voltage electronics without mechanical components. In this work, we present a novel liquid crystal device for laser beam steering. In this device the orientation of the liquid crystal molecules can be controlled. A change in the liquid crystal orientation results in a change of the refractive index. When a laser beam passes through the device, the beam will be deviated (Fig.1) and the device works a prism. The main difference between this device and a prism is that in the device the orientation profile of the liquid crystal molecules can be modified so that the laser beam can be deviated a required angle: the device is tuneable.

New control architecturebased on PXI for a 3-finger haptic device applied to virtual manipulation

To perform advanced manipulation of remote environments such as grasping, more than one finger is required implying higher requirements for the control architecture. This paper presents the design and control of a modular 3-finger haptic device that can be used to interact with virtual scenarios or to teleoperate dexterous remote hands. In a modular haptic device, each module allows the interaction with a scenario by using a single finger; hence, multi-finger interaction can be achieved by adding more modules. Control requirements for a multifinger haptic device are analyzed and new hardware/software architecture for these kinds of devices is proposed. The software architecture described in this paper is distributed and the different modules communicate to allow the remote manipulation. Moreover, an application in which this haptic device is used to interact with a virtual scenario is shown.

Wearable soft robotic device for post-stroke shoulder rehabilitation: identifying misalignments

Stroke is the leading cause of long-term disability in the United States, affecting over 795,000 people annually. In order to regain motor function of the upper body, patients are usually treated by regular sessions with a dedicated physical therapist. A cost-effective wearable upper body orthotics system that can be used at home to empower both the patients and physical therapists is described. The system is composed of a thin, compliant, lightweight, cost-effective soft orthotic device with an integrated cable actuation system that is worn over the upper body, an embedded limb position sensing system, an electric actuator package and controller. The proposed device is robust to misalignments that may occur during actuation of the compliant brace or when putting on the system. Through simulations and experimental evaluation, it was demonstrated i) that the soft orthotic cable-driven shoulder brace can be successfully actuated without the production of off-axis torques in the presence of misalignments and ii) that the proposed model can identify linear and angular misalignments online.

Linewidth influence in photonics logic device

Photonics logic devices are currently finding applications in most of the fields where optical signals are employed. These areas range from optical communications to optical computing, covering as well as other applications in photonics sensing and metrology. Most of the proposed configurations with photonics logic devices are based on semiconductor laser structures with “on/off” behaviors, operating in an optical amplifier configuration. They are able to offer non-linear gain or bistable operation, being these properties the basis for their applications in these fields. Moreover, their large number of potential affecting parameters onto their behavior offers the possibility to choose the best solution for each case.

Total switching of unpolarized light with an electrooptic liquid-crystal device

This paper reports a new family of multimode fiber-optic switching devices based on nematic liquid crystal devices reported by us previously. These devices have a wedged structure as the main characteristic. Several modes of behavior cart arise depending on the internal configuration of the molecules. As we show, fhey have the possibility of total switching of unpolarized light with a very simple structure, low insertion losses, and very low operating voltages These new devices should find a wide range of applications in fiber-optic communication systems.

Evaluation and implementation of a hybrid cross-platform application combining mobile web-technologies and native device functions

Este Proyecto de Fin de Carrera presenta un prototipo de aplicación móvil híbrida multi-plataforma para Android y iOS. Las aplicaciones móviles híbridas son una combinación de aplicaciones web móviles y aplicaciones móviles nativas. Se desarrollan parcialmente con tecnologías web y pueden acceder a la capa nativa y sensores del teléfono. Para el usuario se presentan como aplicaciones nativas, ya que se pueden descargar de las tiendas de aplicaciones y son instaladas en el dispositivo. El prototipo consiste en la migración del módulo de noticias financieras de las aplicaciones actuales para móviles de una compañía bancaria reimplementándolo como aplicación híbrida utilizando uno de los entornos de desarrollo disponibles en el mercado para este propósito. El desarrollo de aplicaciones híbridas puede ahorrar tiempo y dinero cuando se pretende alcanzar más de una plataforma móvil. El objetivo es la evaluación de las ventajas e inconvenientes que ofrece el desarrollo de aplicaciones híbridas en términos de reducción de costes, tiempo de desarrollo y resultado final de la aplicación. El proyecto consta de varias fases. Durante la primera fase se realiza un estudio sobre las aplicaciones híbridas que podemos encontrar hoy en día en el mercado utilizando los ejemplos de linkedIn, Facebook y Financial times. Se hace hincapié en las tecnologías utilizadas, uso de la red móvil y problemas encontrados. Posteriormente se realiza una comparación de distintos entornos de desarrollo multi-plataforma para aplicaciones híbridas en términos de la estrategia utilizada, plataformas soportadas, lenguajes de programación, acceso a capacidades nativas de los dispositivos y licencias de uso. Esta primera fase da como resultado la elección del entorno de desarrollo más adecuado a las exigencias del proyecto, que es PhoneGap, y continua con un análisis más detallado de dicho entorno en cuanto a su arquitectura, características y componentes. La siguiente fase comienza con un estudio de las aplicaciones actuales de la compañía para extraer el código fuente necesario y adaptarlo a la arquitectura que tendrá la aplicación. Para la realización del prototipo se hace uso de la característica que ofrece PhoneGap para acceder a la capa nativa del dispositivo, esto es, el uso de plugins. Se diseña y desarrolla un plugin que permite acceder a la capa nativa para cada plataforma. Una vez desarrollado el prototipo para la plataforma Android, se migra y adapta para la plataforma iOS. Por último se hace una evaluación de los prototipos en cuanto a su facilidad y tiempo de desarrollo, rendimiento, funcionalidad y apariencia de la interfaz de usuario. ABSTRACT. This bachelor's thesis presents a prototype of a hybrid cross-platform mobile application for Android and iOS. Hybrid mobile applications are a combination of mobile web and mobile native applications. They are built partially with web technologies and they can also access native features and sensors of the device. For a user, they look like native applications as they are downloaded from the application stores and installed on the device. This prototype consists of the migration of the financial news module of current mobile applications from a financial bank reimplementing them as a hybrid application using one of the frameworks available in the market for that purpose. Development of applications on a hybrid way can help reducing costs and effort when targeting more than one platform. The target of the project is the evaluation of the advantages and disadvantages that hybrid development can offer in terms of reducing costs and efforts and the final result of the application. The project starts with an analysis of successfully released hybrid applications using the examples of linkedIn, Facebook and Financial Times, emphasizing the different used technologies, the transmitted network data and the encountered problems during the development. This analysis is followed by a comparison of most popular hybrid crossplatform development frameworks in terms of the different approaches, supported platforms, programming languages, access to native features and license. This first stage has the outcome of finding the development framework that best fits to the requirements of the project, that is PhoneGap, and continues with a deeper analysis of its architecture, features and components. Next stage analyzes current company's applications to extract the needed source code and adapt it to the architecture of the prototype. For the realization of the application, the feature that PhoneGap offers to access the native layer of the device is used. This feature is called plugin. A custom plugin is designed and developed to access the native layer of each targeted platform. Once the prototype is finished for Android, it is migrated and adapted to the iOS platform. As a final conclusion the prototypes are evaluated in terms of ease and time of development, performance, functionality and look and feel.

DIMETER: a haptic master device for tremor diagnosis in neurodegenerative diseases

In this study, a device based on patient motion capture is developed for the reliable and non-invasive diagnosis of neurodegenerative diseases. The primary objective of this study is the classification of differential diagnosis between Parkinson's disease (PD) and essential tremor (ET). The DIMETER system has been used in the diagnoses of a significant number of patients at two medical centers in Spain. Research studies on classification have primarily focused on the use of well-known and reliable diagnosis criteria developed by qualified personnel. Here, we first present a literature review of the methods used to detect and evaluate tremor; then, we describe the DIMETER device in terms of the software and hardware used and the battery of tests developed to obtain the best diagnoses. All of the tests are classified and described in terms of the characteristics of the data obtained. A list of parameters obtained from the tests is provided, and the results obtained using multilayer perceptron (MLP) neural networks are presented and analyzed.