Deviation of Cup and Propeller Anemometer Calibration Results with Air Density

The effect of air density variations on the calibration constants of several models of anemometers has been analyzed. The analysis was based on a series of calibrations between March 2003 and February 2011. Results indicate a linear behavior of both calibration constants with the air density. The effect of changes in air density on the measured wind speed by an anemometer was also studied. The results suggest that there can be an important deviation of the measured wind speed with changes in air density from the one at which the anemometer was calibrated, and therefore the need to take this effect into account when calculating wind power estimations.

Analysis of calibration results from cup and propeller anemometers. Influence on wind turbine Annual Energy Production (AEP) calculations

The calibration coefficients of several models of cup and propeller anemometers were analysed. The analysis was based on a series of laboratory calibrations between January 2003 and August 2007. Mean and standard deviation values of calibration coefficients from the anemometers studied were included. Two calibration procedures were used and compared. In the first, recommended by the Measuring network of Wind Energy Institutes (MEASNET), 13 measurement points were taken over a wind speed range of 4 to 16  m  s−1. In the second procedure, 9 measurement points were taken over a wider speed range of 4 to 23  m  s−1. Results indicated no significant differences between the two calibration procedures applied to the same anemometer in terms of measured wind speed and wind turbines' Annual Energy Production (AEP). The influence of the cup anemometers' design on the calibration coefficients was also analysed. The results revealed that the slope of the calibration curve, if based on the rotation frequency and not the anemometer's output frequency, seemed to depend on the cup center rotation radius.

Gasification technology assessment of sterile coal to clean electrical power generation.

Sterile coal is a low-value residue associated to the coal extraction and mining activity. According to the type and origin of the coal bed configuration, sterile coal production can mainly vary on quantity, calorific value and presence of sulphur compounds. In addition, the potential availability of sterile coal within Spain is apparently high and its contribution to the local power generation would be of interest playing a significant role. The proposed study evaluates the availability and deployment of gasification technologies to drive clean electricity generation from waste coal and sterile rock coal, incorporating greenhouse gas emission mitigation systems, like CO2, H2S and NOx removal systems. It establishes the target facility and its conceptual basic design proposal. The syngas obtained after the gasification of sterile coal is processed through specific conditioning units before entering into the combustion chamber of a gas turbine. Flue gas leaving the gas turbine is ducted to a heat recovery steam generation boiler; the steam produced within the boilerdrives a steam turbine. The target facility resembles a singular Integrated Gasification in Combined Cycle (IGCC) power station. The evaluation of the conceptual basic design according to the power output set for a maximum sterile contribution, established that rates over 95% H2S and 90% CO2 removal can be achieved. Noticeable decrease of NOx compounds can be also achieved by the use of commercial technology. A techno-economic approach of the conceptual basic design is made evaluating the integration of potential unitsand their implementation within the target facility aiming toachieve clean power generation. The criterion to be compliant with the most restrictive regulation regarding environmental emissions is setting to carry out this analysis.

Análisis paramétrico determinista y aleatorio de problemas dinámicos en estructuras aeroespaciales

Los fenómenos dinámicos pueden poner en peligro la integridad de estructuras aeroespaciales y los ingenieros han desarrollado diferentes estrategias para analizarlos. Uno de los grandes problemas que se plantean en la ingeniería es cómo atacar un problema dinámico estructural. En la presente tesis se plantean distintos fenómenos dinámicos y se proponen métodos para estimar o simular sus comportamientos mediante un análisis paramétrico determinista y aleatorio del problema. Se han propuesto desde problemas sencillos con pocos grados de libertad que sirven para analizar las diferentes estrategias y herramientas a utilizar, hasta fenómenos muy dinámicos que contienen comportamientos no lineales, daños y fallos. Los primeros ejemplos de investigación planteados cubren una amplia gama de los fenómenos dinámicos, como el análisis de vibraciones de elementos másicos, incluyendo impactos y contactos, y el análisis de una viga con carga armónica aplicada a la que también se le añaden parámetros aleatorios que pueden responder a un desconocimiento o incertidumbre de los mismos. Durante el desarrollo de la tesis se introducen conceptos y se aplican distintos métodos, como el método de elementos finitos (FEM) en el que se analiza su resolución tanto por esquemas implícitos como explícitos, y métodos de análisis paramétricos y estadísticos mediante la técnica de Monte Carlo. Más adelante, una vez ya planteadas las herramientas y estrategias de análisis, se estudian fenómenos más complejos, como el impacto a baja velocidad en materiales compuestos, en el que se busca evaluar la resistencia residual y, por lo tanto, la tolerancia al daño de la estructura. Se trata de un suceso que puede producirse por la caída de herramienta, granizo o restos en la pista de aterrizaje. Otro de los fenómenos analizados también se da en un aeropuerto y se trata de la colisión con un dispositivo frangible, el cual tiene que romperse bajo ciertas cargas y, sin embargo, soportar otras. Finalmente, se aplica toda la metodología planteada en simular y analizar un posible incidente en vuelo, el fenómeno de la pérdida de pala de un turbohélice. Se trata de un suceso muy particular en el que la estructura tiene que soportar unas cargas complejas y excepcionales con las que la aeronave debe ser capaz de completar con éxito el vuelo. El análisis incluye comportamientos no lineales, daños, y varios tipos de fallos, y en el que se trata de identificar los parámetros clave en la secuencia del fallo. El suceso se analiza mediante análisis estructurales deterministas más habituales y también mediante otras técnicas como el método de Monte Carlo con el que se logran estudiar distintas incertidumbres en los parámetros con variables aleatorias. Se estudian, entre otros, el tamaño de pala perdida, la velocidad y el momento en el que se produce la rotura, y la rigidez y resistencia de los apoyos del motor. Se tiene en cuenta incluso el amortiguamiento estructural del sistema. Las distintas estrategias de análisis permiten obtener unos resultados valiosos e interesantes que han sido objeto de distintas publicaciones. ABSTRACT Dynamic phenomena can endanger the integrity of aerospace structures and, consequently, engineers have developed different strategies to analyze them. One of the major engineering problems is how to deal with the structural dynamics. In this thesis, different dynamic phenomena are introduced and several methods are proposed to estimate or simulate their behaviors. The analysis is considered through parametric, deterministic and statistical methods. The suggested issues are from simple problems with few degrees of freedom, in order to develop different strategies and tools to solve them, to very dynamic phenomena containing nonlinear behaviors failures, damages. The first examples cover a wide variety of dynamic phenomena such as vibration analysis of mass elements, including impacts and contacts, and beam analysis with harmonic load applied, in which random parameters are included. These parameters can represent the unawareness or uncertainty of certain variables. During the development of the thesis several concepts are introduced and different methods are applied, such as the finite element method (FEM), which is solved through implicit and explicit schemes, and parametrical and statistical methods using the Monte Carlo analysis technique. Next, once the tools and strategies of analysis are set out more complex phenomena are studied. This is the case of a low-speed impact in composite materials, the residual strength of the structure is evaluated, and therefore, its damage tolerance. This incident may occur from a tool dropped, hail or debris throw on the runway. At an airport may also occur, and it is also analyzed, a collision between an airplane and a frangible device. The devise must brake under these loads, however, it must withstand others. Finally, all the considered methodology is applied to simulate and analyze a flight incident, the blade loss phenomenon of a turboprop. In this particular event the structure must support complex and exceptional loads and the aircraft must be able to successfully complete the flight. Nonlinear behavior, damage, and different types of failures are included in the analysis, in which the key parameters in the failure sequence are identified. The incident is analyzed by deterministic structural analysis and also by other techniques such as Monte Carlo method, in which it is possible to include different parametric uncertainties through random variables. Some of the evaluated parameters are, among others, the blade loss size, propeller rotational frequency, speed and angular position where the blade is lost, and the stiffness and strength of the engine mounts. The study does also research on the structural damping of the system. The different strategies of analysis obtain valuable and interesting results that have been already published.