Code assessment and modelling for Design Basis Accident Analysis of the European sodium fast reactor design. Part I: System description, modelling and benchmarking

The new reactor concepts proposed in the Generation IV International Forum (GIF) are conceived to improve the use of natural resources, reduce the amount of high-level radioactive waste and excel in their reliability and safe operation. Among these novel designs sodium fast reactors (SFRs) stand out due to their technological feasibility as demonstrated in several countries during the last decades. As part of the contribution of EURATOM to GIF the CP-ESFR is a collaborative project with the objective, among others, to perform extensive analysis on safety issues involving renewed SFR demonstrator designs. The verification of computational tools able to simulate the plant behaviour under postulated accidental conditions by code-to-code comparison was identified as a key point to ensure reactor safety. In this line, several organizations employed coupled neutronic and thermal-hydraulic system codes able to simulate complex and specific phenomena involving multi-physics studies adapted to this particular fast reactor technology. In the “Introduction” of this paper the framework of this study is discussed, the second section describes the envisaged plant design and the commonly agreed upon modelling guidelines. The third section presents a comparative analysis of the calculations performed by each organisation applying their models and codes to a common agreed transient with the objective to harmonize the models as well as validating the implementation of all relevant physical phenomena in the different system codes.

Code assessment and modelling for Design Basis Accident analysis of the European Sodium Fast Reactor design. Part II: Optimised core and representative transients analysis

The new reactor concepts proposed in the Generation IV International Forum require the development and validation of computational tools able to assess their safety performance. In the first part of this paper the models of the ESFR design developed by several organisations in the framework of the CP-ESFR project were presented and their reliability validated via a benchmarking exercise. This second part of the paper includes the application of those tools for the analysis of design basis accident (DBC) scenarios of the reference design. Further, this paper also introduces the main features of the core optimisation process carried out within the project with the objective to enhance the core safety performance through the reduction of the positive coolant density reactivity effect. The influence of this optimised core design on the reactor safety performance during the previously analysed transients is also discussed. The conclusion provides an overview of the work performed by the partners involved in the project towards the development and enhancement of computational tools specifically tailored to the evaluation of the safety performance of the Generation IV innovative nuclear reactor designs.

Development of a PWR-W and an AP1000® containment building 3D model with a CFD code for Best-Estimate Thermal-Hydraulic Analysis

The simulation of design basis accidents in a containment building is usually conducted with a lumped parameter model. The codes normally used by Westinghouse Electric Company (WEC) for that license analysis are WGOTHIC or COCO, which are suitable to provide an adequate estimation of the overall peak temperature and pressure of the containment. However, for the detailed study of the thermal-hydraulic behavior in every room and compartment of the containment building, it could be more convenient to model the containment with a more detailed 3D representation of the geometry of the whole building. The main objective of this project is to obtain a standard PWR Westinghouse as well as an AP1000® containment model for a CFD code to analyze the thermal-hydraulic detailed behavior during a design basis accident. In this paper the development and testing of both containment models is presented.

Efficient algorithms for dynamic probabilistic safety assessment. An application to convex damage domain.

The design of nuclear power plant has to follow a number of regulations aimed at limiting the risks inherent in this type of installation. The goal is to prevent and to limit the consequences of any possible incident that might threaten the public or the environment. To verify that the safety requirements are met a safety assessment process is followed. Safety analysis is as key component of a safety assessment, which incorporates both probabilistic and deterministic approaches. The deterministic approach attempts to ensure that the various situations, and in particular accidents, that are considered to be plausible, have been taken into account, and that the monitoring systems and engineered safety and safeguard systems will be capable of ensuring the safety goals. On the other hand, probabilistic safety analysis tries to demonstrate that the safety requirements are met for potential accidents both within and beyond the design basis, thus identifying vulnerabilities not necessarily accessible through deterministic safety analysis alone. Probabilistic safety assessment (PSA) methodology is widely used in the nuclear industry and is especially effective in comprehensive assessment of the measures needed to prevent accidents with small probability but severe consequences. Still, the trend towards a risk informed regulation (RIR) demanded a more extended use of risk assessment techniques with a significant need to further extend PSA’s scope and quality. Here is where the theory of stimulated dynamics (TSD) intervenes, as it is the mathematical foundation of the integrated safety assessment (ISA) methodology developed by the CSN(Consejo de Seguridad Nuclear) branch of Modelling and Simulation (MOSI). Such methodology attempts to extend classical PSA including accident dynamic analysis, an assessment of the damage associated to the transients and a computation of the damage frequency. The application of this ISA methodology requires a computational framework called SCAIS (Simulation Code System for Integrated Safety Assessment). SCAIS provides accident dynamic analysis support through simulation of nuclear accident sequences and operating procedures. Furthermore, it includes probabilistic quantification of fault trees and sequences; and integration and statistic treatment of risk metrics. SCAIS comprehensively implies an intensive use of code coupling techniques to join typical thermal hydraulic analysis, severe accident and probability calculation codes. The integration of accident simulation in the risk assessment process and thus requiring the use of complex nuclear plant models is what makes it so powerful, yet at the cost of an enormous increase in complexity. As the complexity of the process is primarily focused on such accident simulation codes, the question of whether it is possible to reduce the number of required simulation arises, which will be the focus of the present work. This document presents the work done on the investigation of more efficient techniques applied to the process of risk assessment inside the mentioned ISA methodology. Therefore such techniques will have the primary goal of decreasing the number of simulation needed for an adequate estimation of the damage probability. As the methodology and tools are relatively recent, there is not much work done inside this line of investigation, making it a quite difficult but necessary task, and because of time limitations the scope of the work had to be reduced. Therefore, some assumptions were made to work in simplified scenarios best suited for an initial approximation to the problem. The following section tries to explain in detail the process followed to design and test the developed techniques. Then, the next section introduces the general concepts and formulae of the TSD theory which are at the core of the risk assessment process. Afterwards a description of the simulation framework requirements and design is given. Followed by an introduction to the developed techniques, giving full detail of its mathematical background and its procedures. Later, the test case used is described and result from the application of the techniques is shown. Finally the conclusions are presented and future lines of work are exposed.

Contribución al estudio de las metodologías de cálculo realista con incertidumbre (BEPU), dentro del análisis determinista de seguridad de plantas nucleares

El análisis determinista de seguridad (DSA) es el procedimiento que sirve para diseñar sistemas, estructuras y componentes relacionados con la seguridad en las plantas nucleares. El DSA se basa en simulaciones computacionales de una serie de hipotéticos accidentes representativos de la instalación, llamados escenarios base de diseño (DBS). Los organismos reguladores señalan una serie de magnitudes de seguridad que deben calcularse en las simulaciones, y establecen unos criterios reguladores de aceptación (CRA), que son restricciones que deben cumplir los valores de esas magnitudes. Las metodologías para realizar los DSA pueden ser de 2 tipos: conservadoras o realistas. Las metodologías conservadoras utilizan modelos predictivos e hipótesis marcadamente pesimistas, y, por ello, relativamente simples. No necesitan incluir un análisis de incertidumbre de sus resultados. Las metodologías realistas se basan en hipótesis y modelos predictivos realistas, generalmente mecanicistas, y se suplementan con un análisis de incertidumbre de sus principales resultados. Se les denomina también metodologías BEPU (“Best Estimate Plus Uncertainty”). En ellas, la incertidumbre se representa, básicamente, de manera probabilista. Para metodologías conservadores, los CRA son, simplemente, restricciones sobre valores calculados de las magnitudes de seguridad, que deben quedar confinados en una “región de aceptación” de su recorrido. Para metodologías BEPU, el CRA no puede ser tan sencillo, porque las magnitudes de seguridad son ahora variables inciertas. En la tesis se desarrolla la manera de introducción de la incertidumbre en los CRA. Básicamente, se mantiene el confinamiento a la misma región de aceptación, establecida por el regulador. Pero no se exige el cumplimiento estricto sino un alto nivel de certidumbre. En el formalismo adoptado, se entiende por ello un “alto nivel de probabilidad”, y ésta corresponde a la incertidumbre de cálculo de las magnitudes de seguridad. Tal incertidumbre puede considerarse como originada en los inputs al modelo de cálculo, y propagada a través de dicho modelo. Los inputs inciertos incluyen las condiciones iniciales y de frontera al cálculo, y los parámetros empíricos de modelo, que se utilizan para incorporar la incertidumbre debida a la imperfección del modelo. Se exige, por tanto, el cumplimiento del CRA con una probabilidad no menor a un valor P0 cercano a 1 y definido por el regulador (nivel de probabilidad o cobertura). Sin embargo, la de cálculo de la magnitud no es la única incertidumbre existente. Aunque un modelo (sus ecuaciones básicas) se conozca a la perfección, la aplicación input-output que produce se conoce de manera imperfecta (salvo que el modelo sea muy simple). La incertidumbre debida la ignorancia sobre la acción del modelo se denomina epistémica; también se puede decir que es incertidumbre respecto a la propagación. La consecuencia es que la probabilidad de cumplimiento del CRA no se puede conocer a la perfección; es una magnitud incierta. Y así se justifica otro término usado aquí para esta incertidumbre epistémica: metaincertidumbre. Los CRA deben incorporar los dos tipos de incertidumbre: la de cálculo de la magnitud de seguridad (aquí llamada aleatoria) y la de cálculo de la probabilidad (llamada epistémica o metaincertidumbre). Ambas incertidumbres pueden introducirse de dos maneras: separadas o combinadas. En ambos casos, el CRA se convierte en un criterio probabilista. Si se separan incertidumbres, se utiliza una probabilidad de segundo orden; si se combinan, se utiliza una probabilidad única. Si se emplea la probabilidad de segundo orden, es necesario que el regulador imponga un segundo nivel de cumplimiento, referido a la incertidumbre epistémica. Se denomina nivel regulador de confianza, y debe ser un número cercano a 1. Al par formado por los dos niveles reguladores (de probabilidad y de confianza) se le llama nivel regulador de tolerancia. En la Tesis se razona que la mejor manera de construir el CRA BEPU es separando las incertidumbres, por dos motivos. Primero, los expertos defienden el tratamiento por separado de incertidumbre aleatoria y epistémica. Segundo, el CRA separado es (salvo en casos excepcionales) más conservador que el CRA combinado. El CRA BEPU no es otra cosa que una hipótesis sobre una distribución de probabilidad, y su comprobación se realiza de forma estadística. En la tesis, los métodos estadísticos para comprobar el CRA BEPU en 3 categorías, según estén basados en construcción de regiones de tolerancia, en estimaciones de cuantiles o en estimaciones de probabilidades (ya sea de cumplimiento, ya sea de excedencia de límites reguladores). Según denominación propuesta recientemente, las dos primeras categorías corresponden a los métodos Q, y la tercera, a los métodos P. El propósito de la clasificación no es hacer un inventario de los distintos métodos en cada categoría, que son muy numerosos y variados, sino de relacionar las distintas categorías y citar los métodos más utilizados y los mejor considerados desde el punto de vista regulador. Se hace mención especial del método más utilizado hasta el momento: el método no paramétrico de Wilks, junto con su extensión, hecha por Wald, al caso multidimensional. Se decribe su método P homólogo, el intervalo de Clopper-Pearson, típicamente ignorado en el ámbito BEPU. En este contexto, se menciona el problema del coste computacional del análisis de incertidumbre. Los métodos de Wilks, Wald y Clopper-Pearson requieren que la muestra aleatortia utilizada tenga un tamaño mínimo, tanto mayor cuanto mayor el nivel de tolerancia exigido. El tamaño de muestra es un indicador del coste computacional, porque cada elemento muestral es un valor de la magnitud de seguridad, que requiere un cálculo con modelos predictivos. Se hace especial énfasis en el coste computacional cuando la magnitud de seguridad es multidimensional; es decir, cuando el CRA es un criterio múltiple. Se demuestra que, cuando las distintas componentes de la magnitud se obtienen de un mismo cálculo, el carácter multidimensional no introduce ningún coste computacional adicional. Se prueba así la falsedad de una creencia habitual en el ámbito BEPU: que el problema multidimensional sólo es atacable desde la extensión de Wald, que tiene un coste de computación creciente con la dimensión del problema. En el caso (que se da a veces) en que cada componente de la magnitud se calcula independientemente de los demás, la influencia de la dimensión en el coste no se puede evitar. Las primeras metodologías BEPU hacían la propagación de incertidumbres a través de un modelo sustitutivo (metamodelo o emulador) del modelo predictivo o código. El objetivo del metamodelo no es su capacidad predictiva, muy inferior a la del modelo original, sino reemplazar a éste exclusivamente en la propagación de incertidumbres. Para ello, el metamodelo se debe construir con los parámetros de input que más contribuyan a la incertidumbre del resultado, y eso requiere un análisis de importancia o de sensibilidad previo. Por su simplicidad, el modelo sustitutivo apenas supone coste computacional, y puede estudiarse exhaustivamente, por ejemplo mediante muestras aleatorias. En consecuencia, la incertidumbre epistémica o metaincertidumbre desaparece, y el criterio BEPU para metamodelos se convierte en una probabilidad simple. En un resumen rápido, el regulador aceptará con más facilidad los métodos estadísticos que menos hipótesis necesiten; los exactos más que los aproximados; los no paramétricos más que los paramétricos, y los frecuentistas más que los bayesianos. El criterio BEPU se basa en una probabilidad de segundo orden. La probabilidad de que las magnitudes de seguridad estén en la región de aceptación no sólo puede asimilarse a una probabilidad de éxito o un grado de cumplimiento del CRA. También tiene una interpretación métrica: representa una distancia (dentro del recorrido de las magnitudes) desde la magnitud calculada hasta los límites reguladores de aceptación. Esta interpretación da pie a una definición que propone esta tesis: la de margen de seguridad probabilista. Dada una magnitud de seguridad escalar con un límite superior de aceptación, se define el margen de seguridad (MS) entre dos valores A y B de la misma como la probabilidad de que A sea menor que B, obtenida a partir de las incertidumbres de A y B. La definición probabilista de MS tiene varias ventajas: es adimensional, puede combinarse de acuerdo con las leyes de la probabilidad y es fácilmente generalizable a varias dimensiones. Además, no cumple la propiedad simétrica. El término margen de seguridad puede aplicarse a distintas situaciones: distancia de una magnitud calculada a un límite regulador (margen de licencia); distancia del valor real de la magnitud a su valor calculado (margen analítico); distancia desde un límite regulador hasta el valor umbral de daño a una barrera (margen de barrera). Esta idea de representar distancias (en el recorrido de magnitudes de seguridad) mediante probabilidades puede aplicarse al estudio del conservadurismo. El margen analítico puede interpretarse como el grado de conservadurismo (GC) de la metodología de cálculo. Utilizando la probabilidad, se puede cuantificar el conservadurismo de límites de tolerancia de una magnitud, y se pueden establecer indicadores de conservadurismo que sirvan para comparar diferentes métodos de construcción de límites y regiones de tolerancia. Un tópico que nunca se abordado de manera rigurosa es el de la validación de metodologías BEPU. Como cualquier otro instrumento de cálculo, una metodología, antes de poder aplicarse a análisis de licencia, tiene que validarse, mediante la comparación entre sus predicciones y valores reales de las magnitudes de seguridad. Tal comparación sólo puede hacerse en escenarios de accidente para los que existan valores medidos de las magnitudes de seguridad, y eso ocurre, básicamente en instalaciones experimentales. El objetivo último del establecimiento de los CRA consiste en verificar que se cumplen para los valores reales de las magnitudes de seguridad, y no sólo para sus valores calculados. En la tesis se demuestra que una condición suficiente para este objetivo último es la conjunción del cumplimiento de 2 criterios: el CRA BEPU de licencia y un criterio análogo, pero aplicado a validación. Y el criterio de validación debe demostrarse en escenarios experimentales y extrapolarse a plantas nucleares. El criterio de licencia exige un valor mínimo (P0) del margen probabilista de licencia; el criterio de validación exige un valor mínimo del margen analítico (el GC). Esos niveles mínimos son básicamente complementarios; cuanto mayor uno, menor el otro. La práctica reguladora actual impone un valor alto al margen de licencia, y eso supone que el GC exigido es pequeño. Adoptar valores menores para P0 supone menor exigencia sobre el cumplimiento del CRA, y, en cambio, más exigencia sobre el GC de la metodología. Y es importante destacar que cuanto mayor sea el valor mínimo del margen (de licencia o analítico) mayor es el coste computacional para demostrarlo. Así que los esfuerzos computacionales también son complementarios: si uno de los niveles es alto (lo que aumenta la exigencia en el cumplimiento del criterio) aumenta el coste computacional. Si se adopta un valor medio de P0, el GC exigido también es medio, con lo que la metodología no tiene que ser muy conservadora, y el coste computacional total (licencia más validación) puede optimizarse. ABSTRACT Deterministic Safety Analysis (DSA) is the procedure used in the design of safety-related systems, structures and components of nuclear power plants (NPPs). DSA is based on computational simulations of a set of hypothetical accidents of the plant, named Design Basis Scenarios (DBS). Nuclear regulatory authorities require the calculation of a set of safety magnitudes, and define the regulatory acceptance criteria (RAC) that must be fulfilled by them. Methodologies for performing DSA van be categorized as conservative or realistic. Conservative methodologies make use of pessimistic model and assumptions, and are relatively simple. They do not need an uncertainty analysis of their results. Realistic methodologies are based on realistic (usually mechanistic) predictive models and assumptions, and need to be supplemented with uncertainty analyses of their results. They are also termed BEPU (“Best Estimate Plus Uncertainty”) methodologies, and are typically based on a probabilistic representation of the uncertainty. For conservative methodologies, the RAC are simply the restriction of calculated values of safety magnitudes to “acceptance regions” defined on their range. For BEPU methodologies, the RAC cannot be so simple, because the safety magnitudes are now uncertain. In the present Thesis, the inclusion of uncertainty in RAC is studied. Basically, the restriction to the acceptance region must be fulfilled “with a high certainty level”. Specifically, a high probability of fulfillment is required. The calculation uncertainty of the magnitudes is considered as propagated from inputs through the predictive model. Uncertain inputs include model empirical parameters, which store the uncertainty due to the model imperfection. The fulfillment of the RAC is required with a probability not less than a value P0 close to 1 and defined by the regulator (probability or coverage level). Calculation uncertainty is not the only one involved. Even if a model (i.e. the basic equations) is perfectly known, the input-output mapping produced by the model is imperfectly known (unless the model is very simple). This ignorance is called epistemic uncertainty, and it is associated to the process of propagation). In fact, it is propagated to the probability of fulfilling the RAC. Another term used on the Thesis for this epistemic uncertainty is metauncertainty. The RAC must include the two types of uncertainty: one for the calculation of the magnitude (aleatory uncertainty); the other one, for the calculation of the probability (epistemic uncertainty). The two uncertainties can be taken into account in a separate fashion, or can be combined. In any case the RAC becomes a probabilistic criterion. If uncertainties are separated, a second-order probability is used; of both are combined, a single probability is used. On the first case, the regulator must define a level of fulfillment for the epistemic uncertainty, termed regulatory confidence level, as a value close to 1. The pair of regulatory levels (probability and confidence) is termed the regulatory tolerance level. The Thesis concludes that the adequate way of setting the BEPU RAC is by separating the uncertainties. There are two reasons to do so: experts recommend the separation of aleatory and epistemic uncertainty; and the separated RAC is in general more conservative than the joint RAC. The BEPU RAC is a hypothesis on a probability distribution, and must be statistically tested. The Thesis classifies the statistical methods to verify the RAC fulfillment in 3 categories: methods based on tolerance regions, in quantile estimators and on probability (of success or failure) estimators. The former two have been termed Q-methods, whereas those in the third category are termed P-methods. The purpose of our categorization is not to make an exhaustive survey of the very numerous existing methods. Rather, the goal is to relate the three categories and examine the most used methods from a regulatory standpoint. Special mention deserves the most used method, due to Wilks, and its extension to multidimensional variables (due to Wald). The counterpart P-method of Wilks’ is Clopper-Pearson interval, typically ignored in the BEPU realm. The problem of the computational cost of an uncertainty analysis is tackled. Wilks’, Wald’s and Clopper-Pearson methods require a minimum sample size, which is a growing function of the tolerance level. The sample size is an indicator of the computational cost, because each element of the sample must be calculated with the predictive models (codes). When the RAC is a multiple criteria, the safety magnitude becomes multidimensional. When all its components are output of the same calculation, the multidimensional character does not introduce additional computational cost. In this way, an extended idea in the BEPU realm, stating that the multi-D problem can only be tackled with the Wald extension, is proven to be false. When the components of the magnitude are independently calculated, the influence of the problem dimension on the cost cannot be avoided. The former BEPU methodologies performed the uncertainty propagation through a surrogate model of the code, also termed emulator or metamodel. The goal of a metamodel is not the predictive capability, clearly worse to the original code, but the capacity to propagate uncertainties with a lower computational cost. The emulator must contain the input parameters contributing the most to the output uncertainty, and this requires a previous importance analysis. The surrogate model is practically inexpensive to run, so that it can be exhaustively analyzed through Monte Carlo. Therefore, the epistemic uncertainty due to sampling will be reduced to almost zero, and the BEPU RAC for metamodels includes a simple probability. The regulatory authority will tend to accept the use of statistical methods which need a minimum of assumptions: exact, nonparametric and frequentist methods rather than approximate, parametric and bayesian methods, respectively. The BEPU RAC is based on a second-order probability. The probability of the safety magnitudes being inside the acceptance region is a success probability and can be interpreted as a fulfillment degree if the RAC. Furthermore, it has a metric interpretation, as a distance (in the range of magnitudes) from calculated values of the magnitudes to acceptance regulatory limits. A probabilistic definition of safety margin (SM) is proposed in the thesis. The same from a value A to other value B of a safety magnitude is defined as the probability that A is less severe than B, obtained from the uncertainties if A and B. The probabilistic definition of SM has several advantages: it is nondimensional, ranges in the interval (0,1) and can be easily generalized to multiple dimensions. Furthermore, probabilistic SM are combined according to the probability laws. And a basic property: probabilistic SM are not symmetric. There are several types of SM: distance from a calculated value to a regulatory limit (licensing margin); or from the real value to the calculated value of a magnitude (analytical margin); or from the regulatory limit to the damage threshold (barrier margin). These representations of distances (in the magnitudes’ range) as probabilities can be applied to the quantification of conservativeness. Analytical margins can be interpreted as the degree of conservativeness (DG) of the computational methodology. Conservativeness indicators are established in the Thesis, useful in the comparison of different methods of constructing tolerance limits and regions. There is a topic which has not been rigorously tackled to the date: the validation of BEPU methodologies. Before being applied in licensing, methodologies must be validated, on the basis of comparisons of their predictions ad real values of the safety magnitudes. Real data are obtained, basically, in experimental facilities. The ultimate goal of establishing RAC is to verify that real values (aside from calculated values) fulfill them. In the Thesis it is proved that a sufficient condition for this goal is the conjunction of 2 criteria: the BEPU RAC and an analogous criterion for validation. And this las criterion must be proved in experimental scenarios and extrapolated to NPPs. The licensing RAC requires a minimum value (P0) of the probabilistic licensing margin; the validation criterion requires a minimum value of the analytical margin (i.e., of the DG). These minimum values are basically complementary; the higher one of them, the lower the other one. The regulatory practice sets a high value on the licensing margin, so that the required DG is low. The possible adoption of lower values for P0 would imply weaker exigence on the RCA fulfillment and, on the other hand, higher exigence on the conservativeness of the methodology. It is important to highlight that a higher minimum value of the licensing or analytical margin requires a higher computational cost. Therefore, the computational efforts are also complementary. If medium levels are adopted, the required DG is also medium, and the methodology does not need to be very conservative. The total computational effort (licensing plus validation) could be optimized.

The interurban DRAG-Spain model: the main factors of influence on road accidents in Spain

This paper presents the results of applying DRAG methodology to the identification of the main factors of influence on the number of injury and fatal accidents occurring on Spain’s interurban network. Nineteen independent variables have been included in the model grouped together under ten categories: exposure, infrastructure, weather, drivers, economic variables, vehicle stock, surveillance, speed and legislative measures. Highly interesting conclusions can be reached from the results on the basis of the different effects of a single variable on each of the accident types according to severity. The greatest influence revealed by the results is exposure, which together with inexperienced drivers, speed and an ageing vehicle stock, have a negative effect, while the increased surveillance on roads, the improvement in the technological features of vehicles and the proportion of high capacity networks have a positive effect, since the results obtained show a significant drop in accidents.

Including hardware/software co-design in the ASSERT model driven engineering process.

Abstract. The ASSERT project de?ned new software engineering methods and tools for the development of critical embedded real-time systems in the space domain. The ASSERT model-driven engineering process was one of the achievements of the project and is based on the concept of property- preserving model transformations. The key element of this process is that non-functional properties of the software system must be preserved during model transformations. Properties preservation is carried out through model transformations compliant with the Ravenscar Pro?le and provides a formal basis to the process. In this way, the so-called Ravenscar Computational Model is central to the whole ASSERT process. This paper describes the work done in the HWSWCO study, whose main objective has been to address the integration of the Hardware/Software co-design phase in the ASSERT process. In order to do that, non-functional properties of the software system must also be preserved during hardware synthesis. Keywords : Ada 2005, Ravenscar pro?le, Hardware/Software co-design, real- time systems, high-integrity systems, ORK

Optical systems design using the SMS method and optimizations

Resumen El diseño de sistemas ópticos, entendido como un arte por algunos, como una ciencia por otros, se ha realizado durante siglos. Desde los egipcios hasta nuestros días los sistemas de formación de imagen han ido evolucionando así como las técnicas de diseño asociadas. Sin embargo ha sido en los últimos 50 años cuando las técnicas de diseño han experimentado su mayor desarrollo y evolución, debido, en parte, a la aparición de nuevas técnicas de fabricación y al desarrollo de ordenadores cada vez más potentes que han permitido el cálculo y análisis del trazado de rayos a través de los sistemas ópticos de forma rápida y eficiente. Esto ha propiciado que el diseño de sistemas ópticos evolucione desde los diseños desarrollados únicamente a partir de la óptica paraxial hasta lo modernos diseños realizados mediante la utilización de diferentes técnicas de optimización multiparamétrica. El principal problema con el que se encuentra el diseñador es que las diferentes técnicas de optimización necesitan partir de un diseño inicial el cual puede fijar las posibles soluciones. Dicho de otra forma, si el punto de inicio está lejos del mínimo global, o diseño óptimo para las condiciones establecidas, el diseño final puede ser un mínimo local cerca del punto de inicio y lejos del mínimo global. Este tipo de problemática ha llevado al desarrollo de sistemas globales de optimización que cada vez sean menos sensibles al punto de inicio de la optimización. Aunque si bien es cierto que es posible obtener buenos diseños a partir de este tipo de técnicas, se requiere de muchos intentos hasta llegar a la solución deseada, habiendo un entorno de incertidumbre durante todo el proceso, puesto que no está asegurado el que se llegue a la solución óptima. El método de las Superficies Múltiples Simultaneas (SMS), que nació como una herramienta de cálculo de concentradores anidólicos, se ha demostrado como una herramienta también capaz utilizarse para el diseño de sistemas ópticos formadores de imagen, aunque hasta la fecha se ha utilizado para el diseño puntual de sistemas de formación de imagen. Esta tesis tiene por objeto presentar el SMS como un método que puede ser utilizado de forma general para el diseño de cualquier sistema óptico de focal fija o v afocal con un aumento definido así como una herramienta que puede industrializarse para ayudar al diseñador a afrontar de forma sencilla el diseño de sistemas ópticos complejos. Esta tesis está estructurada en cinco capítulos: El capítulo 1, es un capítulo de fundamentos donde se presentan los conceptos fundamentales necesarios para que el lector, aunque no posea una gran base en óptica formadora de imagen, pueda entender los planteamientos y resultados que se presentan en el resto de capítulos El capitulo 2 aborda el problema de la optimización de sistemas ópticos, donde se presenta el método SMS como una herramienta idónea para obtener un punto de partida para el proceso de optimización. Mediante un ejemplo aplicado se demuestra la importancia del punto de partida utilizado en la solución final encontrada. Además en este capítulo se presentan diferentes técnicas que permiten la interpolación y optimización de las superficies obtenidas a partir de la aplicación del SMS. Aunque en esta tesis se trabajará únicamente utilizando el SMS2D, se presenta además un método para la interpolación y optimización de las nubes de puntos obtenidas a partir del SMS3D basado en funciones de base radial (RBF). En el capítulo 3 se presenta el diseño, fabricación y medidas de un objetivo catadióptrico panorámico diseñado para trabajar en la banda del infrarrojo lejano (8-12 μm) para aplicaciones de vigilancia perimetral. El objetivo presentado se diseña utilizando el método SMS para tres frentes de onda de entrada utilizando cuatro superficies. La potencia del método de diseño utilizado se hace evidente en la sencillez con la que este complejo sistema se diseña. Las imágenes presentadas demuestran cómo el prototipo desarrollado cumple a la perfección su propósito. El capítulo 4 aborda el problema del diseño de sistemas ópticos ultra compactos, se introduce el concepto de sistemas multicanal, como aquellos sistemas ópticos compuestos por una serie de canales que trabajan en paralelo. Este tipo de sistemas resultan particularmente idóneos para él diseño de sistemas afocales. Se presentan estrategias de diseño para sistemas multicanal tanto monocromáticos como policromáticos. Utilizando la novedosa técnica de diseño que en este capítulo se presenta el diseño de un telescopio de seis aumentos y medio. En el capítulo 5 se presenta una generalización del método SMS para rayos meridianos. En este capítulo se presenta el algoritmo que debe utilizarse para el diseño de cualquier sistema óptico de focal fija. La denominada optimización fase 1 se vi introduce en el algoritmo presentado de forma que mediante el cambio de las condiciones iníciales del diseño SMS que, aunque el diseño se realice para rayos meridianos, los rayos skew tengan un comportamiento similar. Para probar la potencia del algoritmo desarrollado se presenta un conjunto de diseños con diferente número de superficies. La estabilidad y potencia del algoritmo se hace evidente al conseguirse por primera vez el diseño de un sistema de seis superficies diseñado por SMS. vii Abstract The design of optical systems, considered an art by some and a science by others, has been developed for centuries. Imaging optical systems have been evolving since Ancient Egyptian times, as have design techniques. Nevertheless, the most important developments in design techniques have taken place over the past 50 years, in part due to the advances in manufacturing techniques and the development of increasingly powerful computers, which have enabled the fast and efficient calculation and analysis of ray tracing through optical systems. This has led to the design of optical systems evolving from designs developed solely from paraxial optics to modern designs created by using different multiparametric optimization techniques. The main problem the designer faces is that the different optimization techniques require an initial design which can set possible solutions as a starting point. In other words, if the starting point is far from the global minimum or optimal design for the set conditions, the final design may be a local minimum close to the starting point and far from the global minimum. This type of problem has led to the development of global optimization systems which are increasingly less sensitive to the starting point of the optimization process. Even though it is possible to obtain good designs from these types of techniques, many attempts are necessary to reach the desired solution. This is because of the uncertain environment due to the fact that there is no guarantee that the optimal solution will be obtained. The Simultaneous Multiple Surfaces (SMS) method, designed as a tool to calculate anidolic concentrators, has also proved useful for the design of image-forming optical systems, although until now it has occasionally been used for the design of imaging systems. This thesis aims to present the SMS method as a technique that can be used in general for the design of any optical system, whether with a fixed focal or an afocal with a defined magnification, and also as a tool that can be commercialized to help designers in the design of complex optical systems. The thesis is divided into five chapters. Chapter 1 establishes the basics by presenting the fundamental concepts which the reader needs to acquire, even if he/she doesn‟t have extensive knowledge in the field viii of image-forming optics, in order to understand the steps taken and the results obtained in the following chapters. Chapter 2 addresses the problem of optimizing optical systems. Here the SMS method is presented as an ideal tool to obtain a starting point for the optimization process. The importance of the starting point for the final solution is demonstrated through an example. Additionally, this chapter introduces various techniques for the interpolation and optimization of the surfaces obtained through the application of the SMS method. Even though in this thesis only the SMS2D method is used, we present a method for the interpolation and optimization of clouds of points obtained though the SMS3D method, based on radial basis functions (RBF). Chapter 3 presents the design, manufacturing and measurement processes of a catadioptric panoramic lens designed to work in the Long Wavelength Infrared (LWIR) (8-12 microns) for perimeter surveillance applications. The lens presented is designed by using the SMS method for three input wavefronts using four surfaces. The powerfulness of the design method used is revealed through the ease with which this complex system is designed. The images presented show how the prototype perfectly fulfills its purpose. Chapter 4 addresses the problem of designing ultra-compact optical systems. The concept of multi-channel systems, such as optical systems composed of a series of channels that work in parallel, is introduced. Such systems are especially suitable for the design of afocal systems. We present design strategies for multichannel systems, both monochromatic and polychromatic. A telescope designed with a magnification of six-and-a-half through the innovative technique exposed in this chapter is presented. Chapter 5 presents a generalization of the SMS method for meridian rays. The algorithm to be used for the design of any fixed focal optics is revealed. The optimization known as phase 1 optimization is inserted into the algorithm so that, by changing the initial conditions of the SMS design, the skew rays have a similar behavior, despite the design being carried out for meridian rays. To test the power of the developed algorithm, a set of designs with a different number of surfaces is presented. The stability and strength of the algorithm become apparent when the first design of a system with six surfaces if obtained through the SMS method.

Design equations for reinforced concrete members strengthened in shear with external FRP reinforcement formulated in an evolutionary multi-objective framework

Methods for predicting the shear capacity of FRP shear strengthened RC beams assume the traditional approach of superimposing the contribution of the FRP reinforcing to the contributions from the reinforcing steel and the concrete. These methods become the basis for most guides for the design of externally bonded FRP systems for strengthening concrete structures. The variations among them come from the way they account for the effect of basic shear design parameters on shear capacity. This paper presents a simple method for defining improved equations to calculate the shear capacity of reinforced concrete beams externally shear strengthened with FRP. For the first time, the equations are obtained in a multiobjective optimization framework solved by using genetic algorithms, resulting from considering simultaneously the experimental results of beams with and without FRP external reinforcement. The performance of the new proposed equations is compared to the predictions with some of the current shear design guidelines for strengthening concrete structures using FRPs. The proposed procedure is also reformulated as a constrained optimization problem to provide more conservative shear predictions.

Image analysis by moment invariants using a set of step-like basis functions

Moment invariants have been thoroughly studied and repeatedly proposed as one of the most powerful tools for 2D shape identification. In this paper a set of such descriptors is proposed, being the basis functions discontinuous in a finite number of points. The goal of using discontinuous functions is to avoid the Gibbs phenomenon, and therefore to yield a better approximation capability for discontinuous signals, as images. Moreover, the proposed set of moments allows the definition of rotation invariants, being this the other main design concern. Translation and scale invariance are achieved by means of standard image normalization. Tests are conducted to evaluate the behavior of these descriptors in noisy environments, where images are corrupted with Gaussian noise up to different SNR values. Results are compared to those obtained using Zernike moments, showing that the proposed descriptor has the same performance in image retrieval tasks in noisy environments, but demanding much less computational power for every stage in the query chain.

Fishing effort control regulations influence on stability, safety and operability of small fishing vessels: study of a series of stability related accidents occurred in Spain between 2004 and 2007

Entre los años 2004 y 2007 se hundieron por problemas de estabilidad cinco pesqueros españoles de pequeña eslora, de características parecidas, de relativamente poca edad, que habían sido construidos en un intervalo de pocos años. La mayoría de los tripulantes de esos pesqueros fallecieron o desaparecieron en esos accidentes. Este conjunto de accidentes tuvo bastante repercusión social y mediática. Entre ingenieros navales y marinos del sector de la pesca se relacionó estos accidentes con los condicionantes a los diseños de los pesqueros impuestos por la normativa de control de esfuerzo pesquero. Los accidentes fueron investigados y publicados sus correspondientes informes; en ellos no se exploró esta supuesta relación. Esta tesis pretende investigar la relación entre esos accidentes y los cambios de la normativa de esfuerzo pesquero. En la introducción se expone la normativa de control de esfuerzo pesquero analizada, se presentan datos sobre la estructura de la flota pesquera en España y su accidentalidad, y se detallan los criterios de estabilidad manejados durante el trabajo, explicando su relación con la seguridad de los pesqueros. Seguidamente se realiza un análisis estadístico de la siniestralidad en el sector de la pesca para establecer si el conjunto de accidentes estudiados supone una anomalía, o si por el contrario el conjunto de estos accidentes no es relevante desde el punto de vista estadístico. Se analiza la siniestralidad a partir de diversas bases de datos de buques pesqueros en España y se concluye que el conjunto de accidentes estudiados supone una anomalía estadística, ya que la probabilidad de ocurrencia de los cinco sucesos es muy baja considerando la frecuencia estimada de pérdidas de buques por estabilidad en el subsector de la flota pesquera en el que se encuadran los cinco buques perdidos. A continuación el trabajo se centra en la comparación de los buques accidentados con los buques pesqueros dados de baja para construir aquellos, según exige la normativa de control de esfuerzo pesquero; a estos últimos buques nos referiremos como “predecesores” de los buques accidentados. Se comparan las dimensiones principales de cada buque y de su predecesor, resultando que los buques accidentados comparten características de diseño comunes que son sensiblemente diferentes en los buques predecesores, y enlazando dichas características de diseño con los requisitos de la nueva normativa de control del esfuerzo pesquero bajo la que se construyeron estos barcos. Ello permite establecer una relación entre los accidentes y el mencionado cambio normativo. A continuación se compara el margen con que se cumplían los criterios reglamentarios de estabilidad entre los buques accidentados y los predecesores, encontrándose que en cuatro de los cinco casos los predecesores cumplían los criterios de estabilidad con mayor holgura que los buques accidentados. Los resultados obtenidos en este punto permiten establecer una relación entre el cambio de normativa de esfuerzo pesquero y la estabilidad de los buques. Los cinco buques accidentados cumplían con los criterios reglamentarios de estabilidad en vigor, lo que cuestiona la relación entre esos criterios y la seguridad. Por ello se extiende la comparativa entre pesqueros a dos nuevos campos relacionados con la estabilidad y la seguridad delos buques: • Movimientos a bordo (operatividad del buque), y • Criterios de estabilidad en condiciones meteorológicas adversas El estudio de la operatividad muestra que los buques accidentados tenían, en general, una mayor operatividad que sus predecesores, contrariamente a lo que sucedía con el cumplimiento de los criterios reglamentarios de estabilidad. Por último, se comprueba el desempeño de los diez buques en dos criterios específicos de estabilidad en caso de mal tiempo: el criterio IMO de viento y balance intenso, y un criterio de estabilidad de nueva generación, incluyendo la contribución original del autor de considerar agua en cubierta. Las tendencias observadas en estas dos comparativas son opuestas, lo que permite cuestionar la validez del último criterio sin un control exhaustivo de los parámetros de su formulación, poniendo de manifiesto la necesidad de más investigaciones sobre ese criterio antes de su adopción para uso regulatorio. El conjunto de estos resultados permite obtener una serie de conclusiones en la comparativa entre ambos conjuntos de buques pesqueros. Si bien los resultados de este trabajo no muestran que la aprobación de la nueva normativa de esfuerzo pesquero haya significado una merma general de seguridad en sectores enteros de la flota pesquera, sí se concluye que permitió que algunos diseños de buques pesqueros, posiblemente en busca de la mayor eficiencia compatible con dicha normativa, quedaran con una estabilidad precaria, poniendo de manifiesto que la relación entre seguridad y criterios de estabilidad no es unívoca, y la necesidad de que éstos evolucionen y se adapten a los nuevos diseños de buques pesqueros para continuar garantizando su seguridad. También se concluye que la estabilidad es un aspecto transversal del diseño de los buques, por lo que cualquier reforma normativa que afecte al diseño de los pesqueros o su forma de operar debería estar sujeta a evaluación por parte de las autoridades responsables de la seguridad marítima con carácter previo a su aprobación. ABSTRACT Between 2004 and 2007 five small Spanish fishing vessels sank in stability related accidents. These vessels had similar characteristics, had relatively short age, and had been built in a period of a few years. Most crewmembers of these five vessels died or disappeared in those accidents. This set of accidents had significant social and media impact. Among naval architects and seamen of the fishing sector these accidents were related to the design constraints imposed by the fishing control effort regulations. The accidents were investigated and the official reports issued; this alleged relationship was not explored. This thesis aims to investigate the relationship between those accidents and changes in fishing effort control regulations. In the introduction, the fishing effort control regulation is exposed, data of the Spanish fishing fleet structure and its accident rates are presented, and stability criteria dealt with in this work are explained, detailing its relationship with fishing vessel safety. A statistical analysis of the accident rates in the fishing sector in Spain is performed afterwards. The objective is determining whether the set of accidents studied constitute an anomaly or, on the contrary, they are not statistically relevant. Fishing vessels accident rates is analyzed from several fishing vessel databases in Spain. It is concluded that the set of studied accidents is statistically relevant, as the probability of occurrence of the five happenings is extremely low, considering the loss rates in the subsector of the Spanish fishing fleet where the studied vessels are fitted within. From this point the thesis focuses in comparing the vessels lost and the vessels that were decommissioned to build them as required by the fishing effort control regulation; these vessels will be referred to as “predecessors” of the sunk vessels. The main dimensions between each lost vessel and her predecessor are compared, leading to the conclusion that the lost vessels share design characteristics which are sensibly different from the predecessors, and linking these design characteristics with the requirements imposed by the new fishing control effort regulations. This allows establishing a relationship between the accidents and this regulation change. Then the margin in fulfilling the regulatory stability criteria among the vessels is compared, resulting, in four of the five cases, that predecessors meet the stability criteria with greater clearance than the sunk vessels. The results obtained at this point would establish a relationship between the change of fishing effort control regulation and the stability of vessels. The five lost vessels complied with the stability criteria in force, so the relation between these criteria and safety is put in question. Consequently, the comparison among vessels is extended to other fields related to safety and stability: • Motions onboard (operability), and • Specific stability criteria in rough weather The operability study shows that the lost vessels had in general greater operability than their predecessors, just the opposite as when comparing stability criteria. Finally, performance under specific rough weather stability criteria is checked. The criteria studied are the IMO Weather Criterion, and one of the 2nd generation stability criteria under development by IMO considering in this last case the presence of water on deck, which is an original contribution by the author. The observed trends in these two cases are opposite, allowing to put into question the last criterion validity without an exhaustive control of its formulation parameters; indicating that further research might be necessary before using it for regulatory purposes. The analysis of this set of results leads to some conclusions when comparing both groups of fishing vessels. While the results obtained are not conclusive in the sense that the entry into force of a new fishing effort control in 1998 caused a generalized safety reduction in whole sectors of the Spanish fishing fleet, it can be concluded that it opened the door for some vessel designs resulting with precarious stability. This evidences that the relation between safety and stability criteria is not univocal, so stability criteria needs to evolve for adapting to new fishing vessels designs so their safety is still guaranteed. It is also concluded that stability is a transversal aspect to ship design and operability, implying that any legislative reform affecting ship design or operating modes should be subjected to assessing by the authorities responsible for marine safety before being adopted.

Modelo Híbrido para la Ayuda al Capitán

En esta Tesis se plantea una nueva forma de entender la evacuación apoyándonos en tecnologías existentes y accesibles que nos permitirán ver este proceso como un ente dinámico. Se trata de una metodología que implica no solo el uso de herramientas de análisis que permitan la definición de planes de evacuación en tiempo real, sino que también se apunta hacia la creación de una infraestructura física que permita alimentar con información actualizada al sistema de forma que, según la situación y la evolución de la emergencia, sea posible realizar planes alternativos que se adapten a las nuevas circunstancias. En base a esto, el sistema asimilará toda esa información y aportará soluciones que faciliten la toma de decisiones durante toda la evolución del incidente. Las aportaciones originales de esta Tesis son múltiples y muy variadas, pudiéndolas resumir en los siguientes puntos: 1. Estudio completo del estado del arte: a. Detección y análisis de diferentes proyectos a nivel internacional que de forma parcial tratan algunos aspectos desarrollados en la Tesis. b. Completo estudio a nivel mundial del software desarrollado total o parcialmente para la simulación del comportamiento humano y análisis de procesos de evacuación. Se ha generado una base de datos que cataloga de forma exhaustiva estas aplicaciones, permitiendo realizar un completo análisis y posibilitando la evolución futura de los contenidos de la misma. En la tesis se han analizado casi un centenar de desarrollos, pero el objetivo es seguir completando esta base de datos debido a la gran utilidad y a las importantes posibilidades que ofrece. 2. Desarrollo de un importante capítulo que trata sobre la posibilidad de utilizar entornos virtuales como alternativa intermedia al uso de simuladores y simulacros. En esta sección se divide en dos bloques: a. Ensayos en entornos reales y virtuales. b. Ensayos en entornos virtuales (pruebas realizadas con varios entornos virtuales). 3. Desarrollo de e-Flow net design: paquete de herramientas desarrolladas sobre Rhinoceros para el diseño de la red de evacuación basada en los elementos definidos en la tesis: Nodes, paths, Relations y Areas. 4. Desarrollo de e-Flow Simulator: Conjunto de herramientas que transforman Rhinoceros en un simulador 3D de comportamiento humano. Este simulador, de desarrollo propio, incorpora un novedoso algoritmo de comportamiento a nivel de individuo que incluye aspectos que no se han encontrado en otros simuladores. Esta herramienta permite realizar simulaciones programadas de grupos de individuos cuyo comportamiento se basa en el análisis del entorno y en la presencia de referencias dinámicas. Incluye otras importantes novedades como por ejemplo: herramientas para análisis de la señalización, elementos de señalización dinámica, incorporación sencilla de obstáculos, etc. También se ha creado una herramienta que posibilita la implementación del movimiento del propio escenario simulando la oscilación del mismo, con objeto de reflejar la influencia del movimiento del buque en el desplazamiento de los individuos. 5. En una fase avanzada del desarrollo, se incorporó la posibilidad de generar un vídeo de toda la simulación, momento a partir del cual, se han documentado todas las pruebas (y se continúan documentando) en una base de datos que recoge todas las características de las simulaciones, los problemas detectados, etc. Estas pruebas constituyen, en el momento en que se ha cerrado la redacción de la Tesis, un total de 81 GB de datos. Generación y análisis de rutas en base a la red de evacuación creada con e-Flow Net design y las simulaciones realizadas con e-Flow Net simulator. a. Análisis para la optimización de la configuración de la red en base a los nodos por área existentes. b. Definición de procesos previos al cálculo de rutas posibles. c. Cálculo de rutas: i. Análisis de los diferentes algoritmos que existen en la actualidad para la optimización de rutas. ii. Desarrollo de una nueva familia de algoritmos que he denominado “Minimum Decision Algorithm (MDA)”, siendo los algoritmos que componen esta familia: 1. MDA básico. 2. MDA mínimo. 3. MDA de no interferencia espacial. 4. MDA de expansión. 5. MDA de expansión ordenada para un único origen. 6. MDA de expansión ordenada. iii. Todos estos algoritmos se han implementado en la aplicación e-Flow creada en la Tesis para el análisis de rutas y que constituye el núcleo del Sistema de Ayuda al Capitán. d. Determinación de las alternativas para el plan de evacuación. Tras la definición de las rutas posibles, se describen diferentes procesos existentes de análisis por ponderación en base a criterios, para pasar finalmente a definir el método de desarrollo propio propuesto en esta Tesis y cuyo objetivo es responder en base a la población de rutas posibles obtenidas mediante los algoritmos MDA, qué combinación de rutas constituyen el Plan o Planes más adecuados para cada situación. La metodología creada para la selección de combinaciones de rutas que determinan un Plan completo, se basa en cuatro criterios básicos que tras su aplicación ofrecen las mejores alternativas. En esta fase también se incluye un complejo análisis de evolución temporal que incorpora novedosas definiciones y formulaciones. e. Derivado de la definición de la metodología creada en esta Tesis para la realización de los análisis de evolución temporal, se ha podido definir un nuevo teorema matemático que se ha bautizado como “Familia de cuadriláteros de área constante”. 7. Especificación de la infraestructura física del Sistema de Ayuda al Capitán: parte fundamental de sistema es la infraestructura física sobre la que se sustentaría. Esta infraestructura estaría compuesta por sensores, actuadores, aplicaciones para dispositivos móviles, etc. En este capítulo se analizan los diferentes elementos que la constituirían y las tecnologías implicadas. 8. Especificación de la infraestructura de servicios. 9. Creación del Blog Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/) en el que se han publicado todas las pruebas realizadas en el capítulo que analiza los entornos virtuales como alternativa a los simuladores y a los ensayos en laboratorio o los simulacros, incluyendo en muchos casos la posibilidad de que el visitante del blog pueda realizar la simulación en el entorno virtual. Este blog también incluye otras secciones que se han trabajado durante la Tesis: • Recopilación de diferentes entornos virtuales existentes. • Diagrama que recopila información sobre accidentes tanto en el ámbito marítimo como en el terrestre (en desarrollo). • Esquema propuesto para el acopio de información obtenida a partir de un simulacro. 10. Esta Tesis es la base para el proyecto e-Flow (nombre de una de las aplicaciones que desarrolladas en esta obra), un proyecto en el que el autor de esta Tesis ha trabajado como Project Manager. En el proyecto participa un consorcio de empresas y la UPM, y tiene como objetivo trasladar a la realidad gran parte de los planteamientos e ideas presentadas en esta Tesis. Este proyecto incluye el desarrollo de la infraestructura física y de servicios que permitirán, entre otras cosas, implementar en infraestructuras complejas una plataforma que posibilita la evacuación dinámica y un control ubicuo de los sistemas de monitorización y actuación implementados. En estos momentos se está finalizando el proyecto, cuyo objetivo final es la implementación de un piloto en un Hospital. También destacamos los siguientes avances a nivel de difusión científico-tecnológico: • Ponencia en el “52 congreso de la Ingeniería Naval en España” presentando un artículo “e-Flow- Sistema integral inteligente de soporte a la evacuación”. En este artículo se trata tanto el proyecto e-Flow del que soy Project Manager, como esta Tesis Doctoral, al ser temas estrechamente vinculados. En 2014 se publicó en dos números de la Revista Ingeniería Naval el artículo presentado a estas jornadas. • Co-autor en el artículo “E-Flow: A communication system for user notification in dynamic evacuation scenarios” presentado en el 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) celebrado en Costa Rica. Por último, una de las aportaciones más interesantes, es la definición de un gran número de líneas de investigación futuras en base a todos los avances realizados en esta Tesis. ABSTRACT With this Thesis a new approach for understanding evacuation process is considered, taking advantage of the existing and open technologies that will allow this process to be interpreted as a dynamic entity. The methodology involves not only tools that allows on.-time evacuation plans, but also creates a physical insfrastructure that makes possible to feed the system with information on real time so, considering in each moment the real situation as well as the specific emergency development it will be feasible to generate alternative plans that responds to the current emergency situation. In this respect, the system will store all this information and will feedback with solutions that will help the decision making along the evacuation process. The innovative and singular contributions of this Thesis are numerous and rich, summarised as follows: 1.- Complete state-of-art study: a. Detection and analysis of different projects on an international level that, although partially, deal with some aspects developed in this Thesis. b. Thorough study at a international level of the developed software - total or partially done - for the simulation of the human behaviour and evacuation processes analysis. A database has been generated that classifies in detail these applications allowing to perform a full analysis and leading to future evolution of its contents. Within the Thesis work, almost a hundred of developments have been analysed but the purpose is to keep up updating this database due to the broad applications and possibilities that it involves. 2. Development of an important chapter that studies the possibility of using virtual scenarios as mid-term alternative for the use of simulations. This section is divided in two blocks: a. Trials in virtual and real scenarios b. Trials in virutal scenarios (trials performed with several ones). 3. E-Flow net design development: Set of tools developed under Rhinoceros for the evacuation net design based on the elements defined in the Thesis: Nodes, Paths, Relations, Areas 4. E-Flow simulator development: Set of tools that uses Rhinoceros as a 3D simulator of human behaviour. This simulator, of my own design, includes a new and original algorithm of human behaviour that involves aspects that are not found in other simulators. This tool allows to perform groups programmed simulations which behaviour is based on their enviroment analysis and presence of dynamic references. It includes other important innovations as for example: tools for signals analysis, dynamic signal elements, easy obstacle adding etc... More over, a tool that allows the own scenario movement implementation has been created by simulating the own oscillation movement, with the purpose of playing the vessel movement's influences in the individuals' displacements. 5. In an advanced stage of the development, the possibility of generating a video recording of all the simulation was also integrated, then from that moment all tests have been filed (and keep on doing so) in a database that collects all simulation characteristics, failures detected, etc. These stored tests amounts to a total of 81 GB at the moment of finishing the Thesis work. Generation and analysis of paths regarding the evacuation net created with E-Flow design and the simulations performed with E-Flow net Simulator. a. Analysis for the optimisation of the network configuration based in the existing nodes per area. b. Definition of the processes previous to the calculation of the feasible paths c. Paths calculation: i. Analysis of the different algorithms on existance nowadays for the routes optimisation. ii. Development of a new family of algorithms that I have called “Minimum Decision Algorithm (MDA)”, being composed of: 1. MDA basic 2. MDA minimum 3. MDA of not spacial interference 4. MDA of expansion (es de extenderse) o enlargement ( es de crecimiento) 5. MDA of organised expansion for a single origin (of organised enlargement for a single origin) 6. MDA of organised expansion (of organised enlargement) iii. All these algorithms have been implemented in the E-Flow application created in the Thesis dfor the routes analysis and it is the core of the Captain's support system. d. Determination of the alternatives for the evacuation plan. After defining all possible paths, different processes of analysis existing for weighing-based criteria are described, thus to end defining the own development method proposed in this Thesis and that aims to respond in an agreggation of possible routes basis obtained by means of the MDA algorithms what is the routes' combination more suitable for the Plan or Plans in every situation. The methodology created fot the selection of the combinations of routes that determine a complete Plan is baesd in four basic criteria that after applying, offer the best alternatives. In this stage a complex analysis of the progress along time is also included, that adds original and innovative defintions and formulations. e. Originated from the methodology created in this Thesis for the perfoming of the analysy of the progress along time, a new mathematic theorem has been defined, that has been called as "Family of quadrilateral of constant area". 7. Specification of the physiscal infrastructure of the Captain's help system: essential part is this physical infrastructure that will support it. This system will be made of sensors, actuators, apps for mobile devices etc... Within this chapter the different elements and technologies that make up this infrastructure will be studied. 8. Specification for the services infrastructure. 9. Start up of the Blog. " Virtual Environments (http://epcinnova-virtualenvironments.blogspot.com.es/)" in which all tests performed have been published in terms of analysis of the virtual enviroments as alternative to the simulators as well as to the laboratory experiments or simulations, including in most of the cases the possibility that the visitor can perform the simulation within the virtual enviroment. This blog also includes other sections that have been worked along and within this Thesis: - Collection of different virtual scenarios existent. - Schema that gathers information concerning accidents for maritime and terrestrial areas (under development) - Schema proposed for the collecting of information obtained from a simulation. 10. This Thesis is the basis of the E-Flow project (name of one of the applications developed in this work), a project in which the Thesis' author has worked in as Project Manager. In the project takes part a consortium of firms as well as the UPM and the aim is to bring to real life most part of the approaches and ideas contained in this Thesis. This project includes the development of the physical infrastructure as well as the services that will allow, among others, implement in complex infrastrucutres a platform that will make possible a dynamic evacuation and a continuous control of the monitoring and acting systems implemented. At the moment the project is getting to an end which goal is the implementation of a pilot project in a Hospital. We also would like to highlight the following advances concerning the scientific-technology divulgation: • Talk in the " 52th Congress of the Naval Engineering in Spain" with the article "E-Flow . Intelligent system integrated for supporting evacuation". This paper is about project E-Flow which I am Project Manager of, as well as this Thesis for the Doctorate, being both closely related. Two papers published In 2014 in the Naval Engineering Magazine. • Co-author in the article “E-Flow: A communication system for user notification in dynamic evacuation scenarios” [17] introduced in the 7th International Conference on Ubicuous Computing & Ambient Intelligence (UCAMI) held in Costa Rica. Last, but not least, one of the more interesting contributions is the defintion of several lines of research in the future, based on the advances made in this Thesis.

The historical heritage of domestic architecture is a reliable model for a satisfactory design. The case of the Mediterranean region

The purpose of this paper is to expose the importance of observing cultural systems present in a territory as a reference for the design of urban infrastructures in the new cities and regions of rapid development. If we accept the idea that architecture is an instrument or cultural system developed by man to act as an intermediary to the environment, it is necessary to understand the elemental interaction between man and his environment to meet a satisfactory design. To illustrate this purpose, we present the case of the Eurasian Mediterranean region, where the architectural culture acts as a cultural system of adaptation to the environment and it is formed by an ancient process of selection. From simple observation of architectural types, construction systems and environmental mechanisms treasured in mediterranean historical heritage we can extract crucial information about this elemental interaction. Mediterranean architectural culture has environmental mechanisms responding to the needs of basics habitability, ethnics and passive conditioning. These mechanisms can be basis of an innovative design without compromising the diversity and lifestyles of human groups in the region. The main fundament of our investigation is the determination of the historical heritage of domestic architecture as holder of the formation process of these mechanisms. The result allows us to affirm that the successful introduction of new urban infrastructures in an area need a reliable reference and it must be a cultural system that entailing in essence the environmental conditioning of human existence. The urban infrastructures must be sustainable, understood and accepted by the inhabitants. The last condition is more important when the urban infrastructures are implemented in areas that are developing rapidly or when there is no architectural culture.

Diseño de separadores mediante aplicación informática = Computer Application for Sepators Design

Programa informático desarrollado en plataforma EXCEL (VBA) y dirigido al diseño de Separadores de dos y tres fases, verticales y horizontales. El programa de ordenador o aplicación tiene la capacidad de determinar las propiedades físicas del fluido, utilizando diferentes correlaciones sobre la base del “Black Oil Model”, con dichas propiedades el Programa predice el tipo de flujo presente. Si el tipo de flujo es “Slug Flow” el programa determinara las dimensiones del “Slug catcher” necesario. Bajo las condiciones de funcionamiento existentes el programa diseñará el separador elegido: dos o tres fases, vertical u horizontal. Por último, la aplicación informática estimará el coste del equipo. Abstract Computer program developed in EXCEL (VBA) platform and aimed for the design of Two-Phase, Three-Phase, Vertical or Horizontal Separators. The computer Program or Application has the capability to determine the fluid physical properties utilizing different correlations on the basis of the Black Oil Model, with those Properties the Program will predict the Flow Regime present. If the flow regime is Slug Flow the program will determine the necessary slug catcher dimensions. Under certain operational conditions the program will design the selected: Two-Phase or Three-Phase, Vertical or Horizontal Separator. Finally the computer Application will estimate the cost of the equipment.

Design of a Semi-analytical Method to Describe Plasma-Wall Interactions

Electric probes are objects immersed in the plasma with sharp boundaries which collect of emit charged particles. Consequently, the nearby plasma evolves under abrupt imposed and/or naturally emerging conditions. There could be localized currents, different time scales for plasma species evolution, charge separation and absorbing-emitting walls. The traditional numerical schemes based on differences often transform these disparate boundary conditions into computational singularities. This is the case of models using advection-diffusion differential equations with source-sink terms (also called Fokker-Planck equations). These equations are used in both, fluid and kinetic descriptions, to obtain the distribution functions or the density for each plasma species close to the boundaries. We present a resolution method grounded on an integral advancing scheme by using approximate Green's functions, also called short-time propagators. All the integrals, as a path integration process, are numerically calculated, what states a robust grid-free computational integral method, which is unconditionally stable for any time step. Hence, the sharp boundary conditions, as the current emission from a wall, can be treated during the short-time regime providing solutions that works as if they were known for each time step analytically. The form of the propagator (typically a multivariate Gaussian) is not unique and it can be adjusted during the advancing scheme to preserve the conserved quantities of the problem. The effects of the electric or magnetic fields can be incorporated into the iterative algorithm. The method allows smooth transitions of the evolving solutions even when abrupt discontinuities are present. In this work it is proposed a procedure to incorporate, for the very first time, the boundary conditions in the numerical integral scheme. This numerical scheme is applied to model the plasma bulk interaction with a charge-emitting electrode, dealing with fluid diffusion equations combined with Poisson equation self-consistently. It has been checked the stability of this computational method under any number of iterations, even for advancing in time electrons and ions having different time scales. This work establishes the basis to deal in future work with problems related to plasma thrusters or emissive probes in electromagnetic fields.