Study of the damage evolution of the concrete under freeze-thaw cycles using traditional and non-traditional techniques

Some experiments have been performed to investigate the cyclic freeze-thaw deterioration of concrete, using traditional and non-traditional techniques. Two concrete mixes, with different pore structure, were tested in order to compare the behavior of a freeze-thaw resistant concrete from one that is not. One of the concretes was air entrained, high content of cement and low w/c ratio, and the other one was a lower cement content and higher w/c ratio, without air-entraining agent. Concrete specimens were studied under cyclic freeze-thaw conditions according to UNE-CENT/TS 12390-9 test, using 3% NaCl solution as freezing medium (CDF test: Capillary Suction, De-icing agent and Freeze-thaw Test). The temperature and relative humidity were measured during the cycles inside the specimens using embedded sensors placed at different heights from the surface in contact with the de-icing agent solution. Strain gauges were used to measure the strain variations at the surface of the specimens. Also, measurements of ultrasonic pulse velocity through the concrete specimens were taken before, during, and after the freeze-thaw cycles. According to the CDF test, the failure of the non-air-entraining agent concrete was observed before 28 freeze-thaw cycles; contrariwise, the scaling of the air-entraining agent concrete was only 0.10 kg/m 2 after 28 cycles, versus 3.23 kg/m 2 in the deteriorated concrete, after 28 cycles. Similar behavior was observed on the strain measurements. The residual strain in the deteriorated concrete after 28 cycles was 1150 m versus 65 m, in the air-entraining agent concrete. By means of monitoring the changes of ultrasonic pulse velocity during the freeze-thaw cycles, the deterioration of the tested specimens were assessed

MMonCa: An Object Kinetic Monte Carlo simulator for damage irradiation evolution and defect diffusion

In this work, we introduce the Object Kinetic Monte Carlo (OKMC) simulator MMonCa and simulate the defect evolution in three different materials. We start by explaining the theory of OKMC and showing some details of how such theory is implemented by creating generic structures and algorithms in the objects that we want to simulate. Then we successfully reproduce simulated results for defect evolution in iron, silicon and tungsten using our simulator and compare with available experimental data and similar simulations. The comparisons validate MMonCa showing that it is powerful and flexible enough to be customized and used to study the damage evolution of defects in a wide range of solid materials.

Caracterización multivariada de los temporales para su aplicación en el dimensionamiento del manto principal

En esta tesis se presenta una metodología para la caracterización del oleaje, dentro del marco de las nuevas Recomendaciones para Obras Marítimas (ROM 0.0.-00 y ROM 1.0-09), por ser una de las principales acciones que afectan a la estabilidad de las estructuras marítimas. Debido al carácter aleatorio intrínsecamente multivariado de la acción considerada, las tormentas, su caracterización paramétrica se realiza en términos de funciones cópula uniparamétricas. Las variables consideradas son altura de ola significante del pico de la tormenta, el periodo medio asociado y la magnitud, o número de olas, de todo el ciclo de solicitación. Para establecer un patrón teórico de evolución de la tormenta que permita extrapolar las muestras fuera de la región con datos se analizan los modelos teóricos existentes, comprobándose que no reproducen adecuadamente las tormentas constituidas por estados de mar con un peso importante de oleaje swell. Para evitar esta limitación se proponen cuatro modelos teóricos de evolución de tormentas con distintas formas geométricas. El análisis de los modelos existentes y los propuestos pone de relieve que el Modelo Magnitud Equivalente de Tormenta (EMS= Equivalent Magnitude Storm) con la forma triangular es el que mejor adapta las tormentas constituidas por estados de mar típicos del viento. Para tormentas con un mayor grado de desarrollo, el modelo teórico de tormenta EMS con la forma trapezoidal es el adecuado. De las aproximaciones propuestas para establecer el periodo medio de los sucesivos estados de mar del ciclo de solicitación. la propuesta por Martín Soldevilla et al., (2009) es la más versátil y , en general , mejor reproduce la evolución de todo tipo de tormentas. La caracterización de las tormentas se complementa con la altura de ola máxima. Debido a la mayor disponibilidad y longitud temporal de los datos sintéticos frente a las registros, la práctica totalidad de los análisis de extremos se realizan con tormentas sintéticas en las que la distribución de olas individuales es desconocida. Para evitar esta limitación se utilizan modelos teóricos de distribución de olas acordes a las características de cada uno de los estados de mar que conforman la tormenta sintética. Para establecer dichas características se utiliza la curtosis y en función de su valor la altura de ola máxima se determina asumiendo una determinada distribución de olas. Para estados de mar lineales la distribución de olas individuales de Rayleigh es la considerada. Para condiciones no lineales de gran ancho de banda el modelo de distribución de olas propuesto por Dawson, (2004) es el utilizado y si es de banda estrecha las predicciones de (Boccotti, (1989), Boccotti et al., (2013)) se compara con las resultantes del modelo de Dawson. La caracterización de la evolución de las tormentas en términos multivariados es aplicada al estudio de la progresión del daño del manto principal de diques en talud, y al rebase de las olas. Ambos aspectos cubren el segundo objetivo de la tesis en el que se propone una nueva formulación para el dimensionamiento de mantos constituidos por bloques cúbicos de hormigón. Para el desarrollo de esta nueva formulación se han utilizado los resultados recogidos en los estudios de estabilidad del manto principal de diques talud realizados en modelo físico a escala reducida en el Centro de Estudios de Puertos y Costas (CEDEX) desde la década de los 80 empleando, en su mayoría, bloques paralelepípedos cúbicos de hormigón. Por este motivo y porque los últimos diques construidos en la costa Española utilizan este tipo de pieza, es por lo que la formulación planteada se centra en este tipo de pieza. Después de un primer análisis de las fórmulas de cálculo y de evolución existentes, se llega a la conclusión de que es necesario realizar un esfuerzo de investigación en este campo, así como ensayos en laboratorio y recogida de datos in-situ con base a desarrollar fórmulas de evolución de daño para mantos constituidos por piezas diferentes a la escollera, que tenga en cuenta las principales variables que condiciona su estabilidad. En esta parte de la tesis se propone un método de análisis de evolución de daño, que incluye el criterio de inicio de avería, adecuada para diques en talud constituidos por bloque cúbicos de hormigón y que considera la incidencia oblicua, el daño acumulado y el rebase. This thesis proposes a methodology to estimate sea waves, one of the main actions affecting the maritime structures stability, complying with (ROM 0.0.-00 & ROM 1.0-09.Due to the multivariate behavior of sea storms, the characterization of the structures of sea storms is done using copula function. The analyzed variables are the significant height wave, mean period and magnitude or number of waves during the storm history. The storm evolution in terms of the significant height wave and the mean period is also studied in other to analyze the progressive failure modes. The existing models of evolution are studied, verifying that these approximations do not adjust accurately for developed waves. To overcome this disadvantage, four evolution models are proposed, with some geometrical shapes associated to fit any development degree. The proposed Equivalent Magnitude Storm model, EMS, generally obtains the best results for any kind of storm (predominant sea, swell or both). The triangle is recommended for typical sea storms whereas the trapezoid shape is much more appropriate for more developed storm conditions.The Martín Soldevilla et al., (2009) approach to estimate the mean period is better than others approaches used.The storm characterization is completed with the maximum wave height of the whole storm history. Due to synthetic historical waves databases are more accessible and longer than recorded database, the extreme analyses are done with synthetic data. For this reason the individual waves’ distribution is not known. For that limitation to be avoided, and depending on the characteristics of every sea states, one theoretical model of waves is choose and used. The kurtosis parameter is used to distinguish between linear and nonlinear sea states. The Rayleigh model is used for the linear sea states. For the nonlinear sea states, Dawson, (2004) approach is used for non-narrow bandwidth storms, comparing the results with the Boccotti, (1989), Boccotti et al., (2013) approach, with is used for narrow bandwidth storms. The multivariate and storm evolution characterization is used to analyze of stone armour damage progression and wave overtopping discharge. Both aspects are included in the second part of the thesis, with a new formula is proposed to design cubes armour layer. The results the stability studies of armour layer, done in the Centre for Harbours and Coastal Studies (CEDEX) laboratory are used for defining a new stability formula. For this reason and because the last biggest breakwater built in Spain using the cube, the damage progression is analyze for this kind of concrete block. Before to analyze the existing formulae, it is concluded that it is necessary more investigation, more tests in laboratory and data gathering in situ to define damage evolution formulae to armour of other kind of pieces and that takes to account the principal variables. This thesis proposed a method to calculate the damage progression including oblique waves, accumulated damage, and overtopping effect. The method also takes account the beginning of the movement of the blocks.

Storm evolution characterization for analysing stone armour damage progression

Storm evolution is fundamental for analysing the damage progression of the different failure modes and establishing suitable protocols for maintaining and optimally sizing structures. However, this aspect has hardly been studied and practically the whole of the studies dealing with the subject adopt the Equivalent triangle storm. As against this approach, two new ones are proposed. The first is the Equivalent Triangle Magnitude Storm model (ETMS), whose base, the triangular storm duration, D, is established such that its magnitude (area describing the storm history above the reference threshold level which sets the storm condition),HT, equals the real storm magnitude. The other is the Equivalent Triangle Number of Waves Storm (ETNWS), where the base is referred in terms of the real storm's number of waves,Nz. Three approaches are used for estimating the mean period, Tm, associated to each of the sea states defining the storm evolution, which is necessary to determine the full energy flux withstood by the structure in the course of the extreme event. Two are based on the Jonswap spectrum representativity and the other uses the bivariate Gumbel copula (Hs, Tm), resulting from adjusting the storm peaks. The representativity of the approaches proposed and those defined in specialised literature are analysed by comparing the main armour layer's progressive loss of hydraulic stability caused by real storms and that relating to theoretical ones. An empirical maximum energy flux model is used for this purpose. The agreement between the empirical and theoretical results demonstrates that the representativity of the different approaches depends on the storm characteristics and point towards a need to investigate other geometrical shapes to characterise the storm evolution associated with sea states heavily influenced by swell wave components.

Influence of termal fluctuations in radiation damage cascade production and defect dynamics in tungsten

The detailed study of the deterioration suffered by the materials of the components of a nuclear facility, in particular those forming part of the reactor core, is a topic of great interest which importance derives in large technological and economic implications. Since changes in the atomic-structural properties of relevant components pose a risk to the smooth operation with clear consequences for security and life of the plant, controlling these factors is essential in any development of engineering design and implementation. In recent times, tungsten has been proposed as a structural material based on its good resistance to radiation, but still needs to be done an extensive study on the influence of temperature on the behavior of this material under radiation damage. This work aims to contribute in this regard. Molecular Dynamics (MD) simulations were carried out to determine the influence of temperature fluctuations on radiation damage production and evolution in Tungsten. We have particularly focused our study in the dynamics of defect creation, recombination, and diffusion properties. PKA energies were sampled in a range from 5 to 50 KeV. Three different temperature scenarios were analyzed, from very low temperatures (0-200K), up to high temperature conditions (300-500 K). We studied the creation of defects, vacancies and interstitials, recombination rates, diffusion properties, cluster formation, their size and evolution. Simulations were performed using Lammps and the Zhou EAM potential for W

Storm characterization for analyzing stone armour damage progression

Storm evolution is fundamental for analysing the damage progression of the different failure modes and establishing suitable protocols for maintaining and optimally sizing structures. However, this aspect has hardly been studied and practically the whole of the studies dealing with the subject adopt the Equivalent triangle storm. As against this approach, two new ones are proposed. The first is the Equivalent Triangle Magnitude Storm model (ETMS), whose base, the triangular storm duration, D, is established such that its magnitude (area describing the storm history above the reference threshold level which sets the storm condition),HT, equals the real storm magnitude. The other is the Equivalent Triangle Number of Waves Storm (ETNWS), where the base is referred in terms of the real storm's number of waves,Nz. Three approaches are used for estimating the mean period, Tm, associated to each of the sea states defining the storm evolution, which is necessary to determine the full energy flux withstood by the structure in the course of the extreme event. Two are based on the Jonswap spectrum representativity and the other uses the bivariate Gumbel copula (Hs, Tm), resulting from adjusting the storm peaks. The representativity of the approaches proposed and those defined in specialised literature are analysed by comparing the main armour layer's progressive loss of hydraulic stability caused by real storms and that relating to theoretical ones. An empirical maximum energy flux model is used for this purpose. The agreement between the empirical and theoretical results demonstrates that the representativity of the different approaches depends on the storm characteristics and point towards a need to investigate other geometrical shapes to characterise the storm evolution associated with sea states heavily influenced by swell wave components.

Use of the energy-release rate in a 2 scale damage analysis of a bonded joint

Stress singularities appear at the extremities of an adhesive bond. They can produce a damage mechanism that we assimilate in this Note to a crack. The energy release rate permits to characterize its evolution. But a very refined mesh would be necessary for a real structure. Using an asymptotic method based on the small thickness of the bond a limit model with a different local behaviour is suggested. It leads to an approximation of the energy release rate

Atomistic modeling of Ge damage accumulation, amorphization and solid phase epitaxial regrowth

En los últimos años, el Ge ha ganado de nuevo atención con la finalidad de ser integrado en el seno de las existentes tecnologías de microelectrónica. Aunque no se le considera como un canddato capaz de reemplazar completamente al Si en el futuro próximo, probalemente servirá como un excelente complemento para aumentar las propiedades eléctricas en dispositivos futuros, especialmente debido a su alta movilidad de portadores. Esta integración requiere de un avance significativo del estado del arte en los procesos de fabricado. Técnicas de simulación, como los algoritmos de Monte Carlo cinético (KMC), proporcionan un ambiente atractivo para llevar a cabo investigación y desarrollo en este campo, especialmente en términos de costes en tiempo y financiación. En este estudio se han usado, por primera vez, técnicas de KMC con el fin entender el procesado “front-end” de Ge en su fabricación, específicamente la acumulación de dañado y amorfización producidas por implantación iónica y el crecimiento epitaxial en fase sólida (SPER) de las capas amorfizadas. Primero, simulaciones de aproximación de clisiones binarias (BCA) son usadas para calcular el dañado causado por cada ión. La evolución de este dañado en el tiempo se simula usando KMC sin red, o de objetos (OKMC) en el que sólamente se consideran los defectos. El SPER se simula a través de una aproximación KMC de red (LKMC), siendo capaz de seguir la evolución de los átomos de la red que forman la intercara amorfo/cristalina. Con el modelo de amorfización desarrollado a lo largo de este trabajo, implementado en un simulador multi-material, se pueden simular todos estos procesos. Ha sido posible entender la acumulación de dañado, desde la generación de defectos puntuales hasta la formación completa de capas amorfas. Esta acumulación ocurre en tres regímenes bien diferenciados, empezando con un ritmo lento de formación de regiones de dañado, seguido por una rápida relajación local de ciertas áreas en la fase amorfa donde ambas fases, amorfa y cristalina, coexisten, para terminar en la amorfización completa de capas extensas, donde satura el ritmo de acumulación. Dicha transición ocurre cuando la concentración de dañado supera cierto valor límite, el cual es independiente de las condiciones de implantación. Cuando se implantan los iones a temperaturas relativamente altas, el recocido dinámico cura el dañado previamente introducido y se establece una competición entre la generación de dañado y su disolución. Estos efectos se vuelven especialmente importantes para iones ligeros, como el B, el cual crea dañado más diluido, pequeño y distribuido de manera diferente que el causado por la implantación de iones más pesados, como el Ge. Esta descripción reproduce satisfactoriamente la cantidad de dañado y la extensión de las capas amorfas causadas por implantación iónica reportadas en la bibliografía. La velocidad de recristalización de la muestra previamente amorfizada depende fuertemente de la orientación del sustrato. El modelo LKMC presentado ha sido capaz de explicar estas diferencias entre orientaciones a través de un simple modelo, dominado por una única energía de activación y diferentes prefactores en las frecuencias de SPER dependiendo de las configuraciones de vecinos de los átomos que recristalizan. La formación de maclas aparece como una consecuencia de esta descripción, y es predominante en sustratos crecidos en la orientación (111)Ge. Este modelo es capaz de reproducir resultados experimentales para diferentes orientaciones, temperaturas y tiempos de evolución de la intercara amorfo/cristalina reportados por diferentes autores. Las parametrizaciones preliminares realizadas de los tensores de activación de tensiones son también capaces de proveer una buena correlación entre las simulaciones y los resultados experimentales de velocidad de SPER a diferentes temperaturas bajo una presión hidrostática aplicada. Los estudios presentados en esta tesis han ayudado a alcanzar un mejor entendimiento de los mecanismos de producción de dañado, su evolución, amorfización y SPER para Ge, además de servir como una útil herramienta para continuar el trabajo en este campo. In the recent years, Ge has regained attention to be integrated into existing microelectronic technologies. Even though it is not thought to be a feasible full replacement to Si in the near future, it will likely serve as an excellent complement to enhance electrical properties in future devices, specially due to its high carrier mobilities. This integration requires a significant upgrade of the state-of-the-art of regular manufacturing processes. Simulation techniques, such as kinetic Monte Carlo (KMC) algorithms, provide an appealing environment to research and innovation in the field, specially in terms of time and funding costs. In the present study, KMC techniques are used, for the first time, to understand Ge front-end processing, specifically damage accumulation and amorphization produced by ion implantation and Solid Phase Epitaxial Regrowth (SPER) of the amorphized layers. First, Binary Collision Approximation (BCA) simulations are used to calculate the damage caused by every ion. The evolution of this damage over time is simulated using non-lattice, or Object, KMC (OKMC) in which only defects are considered. SPER is simulated through a Lattice KMC (LKMC) approach, being able to follow the evolution of the lattice atoms forming the amorphous/crystalline interface. With the amorphization model developed in this work, implemented into a multi-material process simulator, all these processes can be simulated. It has been possible to understand damage accumulation, from point defect generation up to full amorphous layers formation. This accumulation occurs in three differentiated regimes, starting at a slow formation rate of the damage regions, followed by a fast local relaxation of areas into the amorphous phase where both crystalline and amorphous phases coexist, ending in full amorphization of extended layers, where the accumulation rate saturates. This transition occurs when the damage concentration overcomes a certain threshold value, which is independent of the implantation conditions. When implanting ions at relatively high temperatures, dynamic annealing takes place, healing the previously induced damage and establishing a competition between damage generation and its dissolution. These effects become specially important for light ions, as B, for which the created damage is more diluted, smaller and differently distributed than that caused by implanting heavier ions, as Ge. This description successfully reproduces damage quantity and extension of amorphous layers caused by means of ion implantation reported in the literature. Recrystallization velocity of the previously amorphized sample strongly depends on the substrate orientation. The presented LKMC model has been able to explain these differences between orientations through a simple model, dominated by one only activation energy and different prefactors for the SPER rates depending on the neighboring configuration of the recrystallizing atoms. Twin defects formation appears as a consequence of this description, and are predominant for (111)Ge oriented grown substrates. This model is able to reproduce experimental results for different orientations, temperatures and times of evolution of the amorphous/crystalline interface reported by different authors. Preliminary parameterizations for the activation strain tensors are able to also provide a good match between simulations and reported experimental results for SPER velocities at different temperatures under the appliance of hydrostatic pressure. The studies presented in this thesis have helped to achieve a greater understanding of damage generation, evolution, amorphization and SPER mechanisms in Ge, and also provide a useful tool to continue research in this field.