Reduction of truncation errors in planar, cylindrical and partial spherical near-field antenna measurements

A method to reduce truncation errors in near-field antenna measurements is presented. The method is based on the Gerchberg-Papoulis iterative algorithm used to extrapolate band-limited functions and it is able to extend the valid region of the calculated far-field pattern up to the whole forward hemisphere. The extension of the valid region is achieved by the iterative application of a transformation between two different domains. After each transformation, a filtering process that is based on known information at each domain is applied. The first domain is the spectral domain in which the plane wave spectrum (PWS) is reliable only within a known region. The second domain is the field distribution over the antenna under test (AUT) plane in which the desired field is assumed to be concentrated on the antenna aperture. The method can be applied to any scanning geometry, but in this paper, only the planar, cylindrical, and partial spherical near-field measurements are considered. Several simulation and measurement examples are presented to verify the effectiveness of the method.

Correction of systematic errors in Wide Area Multilateration

This work presents a method to estimate and correct slow time-dependent position errors due to non perfect ground station synchronization and tropospheric propagation. It uses opportunity traffic emissions, i.e. signals transmitted from the aircrafts within the coverage zone. This method is used to overcome the difficulty of installing reference beacons simultaneously visible by all the base stations in a given Wide Area Multilateration (WAM) system.

A New Method to Reduce Truncation Errors in Partial Spherical Near-Field Measurements

A new and effective method for reduction of truncation errors in partial spherical near-field (SNF) measurements is proposed. The method is useful when measuring electrically large antennas, where the measurement time with the classical SNF technique is prohibitively long and an acquisition over the whole spherical surface is not practical. Therefore, to reduce the data acquisition time, partial sphere measurement is usually made, taking samples over a portion of the spherical surface in the direction of the main beam. But in this case, the radiation pattern is not known outside the measured angular sector as well as a truncation error is present in the calculated far-field pattern within this sector. The method is based on the Gerchberg-Papoulis algorithm used to extrapolate functions and it is able to extend the valid region of the calculated far-field pattern up to the whole forward hemisphere. To verify the effectiveness of the method, several examples are presented using both simulated and measured truncated near-field data.

New methods to reduce leakage errors in planar near-field measurements

This paper describes two methods to cancel the effect of two kinds of leakage signals which may be presented when an antenna is measured in a planar near-field range. One method tries to reduce leakage bias errors from the receiver¿s quadrature detector and it is based on estimating the bias constant added to every near-field data sample. Then, that constant is subtracted from the data, removing its undesired effect on the far-field pattern. The estimation is performed by back-propagating the field from the scan plane to the antenna under test plane (AUT) and averaging all the data located outside the AUT aperture. The second method is able to cancel the effect of the leakage from faulty transmission lines, connectors or rotary joints. The basis of this method is also a reconstruction process to determine the field distribution on the AUT plane. Once this distribution is known, a spatial filtering is applied to cancel the contribution due to those faulty elements. After that, a near-field-to-far-field transformation is applied, obtaining a new radiation pattern where the leakage effects have disappeared. To verify the effectiveness of both methods, several examples are presented.

Subjective Evaluation of Transmission Errors in IPTV and 3DTV

The increase of multimedia services delivered over packet-based networks has entailed greater quality expectations of the end-users. This has led to an intensive research on techniques for evaluating the quality of experience perceived by the viewers of audiovisual content, considering the different degradations that it could suffer along the broadcasting system. In this paper, a comprehensive study of the impact of transmission errors affecting video and audio in IPTV is presented. With this aim, subjective assessment tests were carried out proposing a novel methodology trying to keep as close as possible home environment viewing conditions. Also 3DTV content in side-by-side format has been used in the experiments to compare the impact of the degradations. The results provide a better understanding of the effects of transmission errors, and show that the QoE related to the first approach of 3DTV is acceptable, but the visual discomfort that it causes should be reduced.

Subjective assessment of the impact of transmission errors in 3DTV compared to HDTV

Recently, broadcasted 3D video content has reached households with the first generation of 3DTV. However, few studies have been done to analyze the Quality of Experience (QoE) perceived by the end-users in this scenario. This paper studies the impact of trans- mission errors in 3DTV, considering that the video is delivered in side-by-side format over a conventional packet-based network. For this purpose, a novel evaluation methodology based on standard sin- gle stimulus methods and with the aim of keeping as close as pos- sible the home environment viewing conditions has been proposed. The effects of packet losses in monoscopic and stereoscopic videos are compared from the results of subjective assessment tests. Other aspects were also measured concerning 3D content as naturalness, sense of presence and visual fatigue. The results show that although the final perceived QoE is acceptable, some errors cause important binocular rivalry, and therefore, substantial visual discomfort.

Tomas Lopez's Geographic Atlas of Spain in the Peninsular War: A methodology for determining errors

During the Peninsular War, Napoleon's and Wellington's armies were aware of the lack of precision in the maps of Spain and its provinces that appeared in Tomas Lopez \s Geographical Atlas of Spain. The errors were due to the non-topographical surveying method he used which he had learned from his teacher Jean Baptiste Bourguignon D 'Anville. To map all of the Spanish provinces, Tomas Lopez divided them into circles of three leagues in diameter (16,718 m), taking a particular town as the centre. He asked the town's priest to draw a map of the territory and to complete a questionnaire that Tomas Lopez sent to him. The priest was to return the two documents after he had completed them. Subsequently, at his desk, Tomas Lopez used the maps and reports as well as other graphic and written sources from various locations to make an outline of each map. Next, he made a mosaic that served as a pattern for drawing the final provincial map. We will see the way that this method was applied in two concrete cases: the villages ofChavaler and Monteagudo, situated in the Spanish province of Soria, and verify their degree of accuracy. We will use the maps drawn by the priests in 1767, the final map of the province which was published in 1804 by Tomás López, and a current map of the province showing the angular and linear errors in Lopez \s map.

The history of technology in education. A comparative study and forecast

Area, launched in 1999 with the Bologna Declaration, has bestowed such a magnitude and unprecedented agility to the transformation process undertaken by European universities. However, the change has been more profound and drastic with regards to the use of new technologies both inside and outside the classroom. This article focuses on the study and analysis of the technology’s history within the university education and its impact on teachers, students and teaching methods. All the elements that have been significant and innovative throughout the history inside the teaching process have been analyzed, from the use of blackboard and chalk during lectures, the use of slide projectors and transparent slides, to the use of electronic whiteboards and Internet nowadays. The study is complemented with two types of surveys that have been performed among teachers and students during the school years 1999 - 2011 in the School of Civil Engineering at the Polytechnic University of Madrid. The pros and cons of each of the techniques and methodologies used in the learning process over the last decades are described, unfolding how they have affected the teacher, who has evolved from writing on a whiteboard to project onto a screen, the student, who has evolved from taking handwritten notes to download information or search the Internet, and the educational process, that has evolved from the lecture to acollaborative learning and project-based learning. It is unknown how the process of learning will evolve in the future, but we do know the consequences that some of the multimedia technologies are having on teachers, students and the learning process. It is our goal as teachers to keep ourselves up to date, in order to offer the student adequate technical content, while providing proper motivation through the use of new technologies. The study provides a forecast in the evolution of multimedia within the classroom and the renewal of the education process, which in our view, will set the basis for future learning process within the context of this new interactive era.

Economics and forecast of energy consumption in NGN networks: the case of Spain

Reducing energy consumption is one of the main goals of sustainability planning in most countries. For instance in Europe, the EC established the objectives in the Communication “20 20 by 2020 Europe's climate change opportunity”.

Energy Consumption Forecast in 4G Networks: The Case of Spain

Reducing energy consumption is one of the main goals of sustainability planning in most countries. For instance in Europe, the EC established the objectives in the Communication “20 20 by 2020 Europe's climate change opportunity”. • Next Generation Networks (NGN)  One of the most relevant upcoming ICT development • The role of energy consumption seems mostly absent from the main analysis and the debate on NGN deployment.

Contribution to energy consumption modelling and forecast in next generation access networks

La contribución del sector de las tecnologías de la información y las comunicaciones (TICs) al consumo de energía a nivel global se ha visto incrementada considerablemente en la última década al mismo tiempo que su relevancia dentro de la economía global. Se prevé que esta tendencia continúe debido al uso cada vez más intensivo de estas tecnologías. Una de las principales causas es el tráfico de datos de banda ancha generado por el uso de las redes de telecomunicaciones. De hecho como respuesta a esta demanda de recursos por parte de los usuarios, de la industria de las telecomunicaciones está iniciando el despliegue de las redes de nueva generación. En cualquier caso, el consumo de energía es un factor generalmente ausente del debate sobre el despliegue de estas tecnologías, a pesar de la posible repercusión que pueda llegar a tener en los costes y la sostenibilidad de estos proyectos. A lo largo de este trabajo se desarrollan modelos para evaluar el consumo energético de las redes de acceso de nueva generación (NGAN). Estos servirán tanto para llevar a cabo cálculos en un escenario global estático, como en cualquiera otro que determine la potencial evolución de la red de acceso a lo largo de su despliegue. Estos modelos combinan tres factores: la penetración prospectiva de cada una de las tecnologías de banda ancha analizadas, el tráfico generado por usuario y su futura evolución, y el perfil de consumo de energía de cada uno de los dispositivos de red desplegados. Tras evaluar los resultados derivados de la aplicación de los modelos en el caso demográfico específico de España, se obtienen conclusiones acerca de las diferencias tecnológicas en cuanto al consumo energético, sus implicaciones económicas, y la sensibilidad de los cálculos atendiendo a posibles modificaciones en los valores de referencia de diferentes parámetros de diseño. Se destaca por tanto el efecto en el consumo energético de los desarrollos tecnológicos, tecno-económicos, y de las decisiones en el ámbito regulatorio. Aunque como se ha dicho, se ha ejemplificado el cálculo para un caso particular, tanto los modelos como las conclusiones extraídas se pueden extrapolar a otros países similares.

Localization and Tracking in Energy-Constrained Networks with Dynamic Connectivity

Systems used for target localization, such as goods, individuals, or animals, commonly rely on operational means to meet the final application demands. However, what would happen if some means were powered up randomly by harvesting systems? And what if those devices not randomly powered had their duty cycles restricted? Under what conditions would such an operation be tolerable in localization services? What if the references provided by nodes in a tracking problem were distorted? Moreover, there is an underlying topic common to the previous questions regarding the transfer of conceptual models to reality in field tests: what challenges are faced upon deploying a localization network that integrates energy harvesting modules? The application scenario of the system studied is a traditional herding environment of semi domesticated reindeer (Rangifer tarandus tarandus) in northern Scandinavia. In these conditions, information on approximate locations of reindeer is as important as environmental preservation. Herders also need cost-effective devices capable of operating unattended in, sometimes, extreme weather conditions. The analyses developed are worthy not only for the specific application environment presented, but also because they may serve as an approach to performance of navigation systems in absence of reasonably accurate references like the ones of the Global Positioning System (GPS). A number of energy-harvesting solutions, like thermal and radio-frequency harvesting, do not commonly provide power beyond one milliwatt. When they do, battery buffers may be needed (as it happens with solar energy) which may raise costs and make systems more dependent on environmental temperatures. In general, given our problem, a harvesting system is needed that be capable of providing energy bursts of, at least, some milliwatts. Many works on localization problems assume that devices have certain capabilities to determine unknown locations based on range-based techniques or fingerprinting which cannot be assumed in the approach considered herein. The system presented is akin to range-free techniques, but goes to the extent of considering very low node densities: most range-free techniques are, therefore, not applicable. Animal localization, in particular, uses to be supported by accurate devices such as GPS collars which deplete batteries in, maximum, a few days. Such short-life solutions are not particularly desirable in the framework considered. In tracking, the challenge may times addressed aims at attaining high precision levels from complex reliable hardware and thorough processing techniques. One of the challenges in this Thesis is the use of equipment with just part of its facilities in permanent operation, which may yield high input noise levels in the form of distorted reference points. The solution presented integrates a kinetic harvesting module in some nodes which are expected to be a majority in the network. These modules are capable of providing power bursts of some milliwatts which suffice to meet node energy demands. The usage of harvesting modules in the aforementioned conditions makes the system less dependent on environmental temperatures as no batteries are used in nodes with harvesters--it may be also an advantage in economic terms. There is a second kind of nodes. They are battery powered (without kinetic energy harvesters), and are, therefore, dependent on temperature and battery replacements. In addition, their operation is constrained by duty cycles in order to extend node lifetime and, consequently, their autonomy. There is, in turn, a third type of nodes (hotspots) which can be static or mobile. They are also battery-powered, and are used to retrieve information from the network so that it is presented to users. The system operational chain starts at the kinetic-powered nodes broadcasting their own identifier. If an identifier is received at a battery-powered node, the latter stores it for its records. Later, as the recording node meets a hotspot, its full record of detections is transferred to the hotspot. Every detection registry comprises, at least, a node identifier and the position read from its GPS module by the battery-operated node previously to detection. The characteristics of the system presented make the aforementioned operation own certain particularities which are also studied. First, identifier transmissions are random as they depend on movements at kinetic modules--reindeer movements in our application. Not every movement suffices since it must overcome a certain energy threshold. Second, identifier transmissions may not be heard unless there is a battery-powered node in the surroundings. Third, battery-powered nodes do not poll continuously their GPS module, hence localization errors rise even more. Let's recall at this point that such behavior is tight to the aforementioned power saving policies to extend node lifetime. Last, some time is elapsed between the instant an identifier random transmission is detected and the moment the user is aware of such a detection: it takes some time to find a hotspot. Tracking is posed as a problem of a single kinetically-powered target and a population of battery-operated nodes with higher densities than before in localization. Since the latter provide their approximate positions as reference locations, the study is again focused on assessing the impact of such distorted references on performance. Unlike in localization, distance-estimation capabilities based on signal parameters are assumed in this problem. Three variants of the Kalman filter family are applied in this context: the regular Kalman filter, the alpha-beta filter, and the unscented Kalman filter. The study enclosed hereafter comprises both field tests and simulations. Field tests were used mainly to assess the challenges related to power supply and operation in extreme conditions as well as to model nodes and some aspects of their operation in the application scenario. These models are the basics of the simulations developed later. The overall system performance is analyzed according to three metrics: number of detections per kinetic node, accuracy, and latency. The links between these metrics and the operational conditions are also discussed and characterized statistically. Subsequently, such statistical characterization is used to forecast performance figures given specific operational parameters. In tracking, also studied via simulations, nonlinear relationships are found between accuracy and duty cycles and cluster sizes of battery-operated nodes. The solution presented may be more complex in terms of network structure than existing solutions based on GPS collars. However, its main gain lies on taking advantage of users' error tolerance to reduce costs and become more environmentally friendly by diminishing the potential amount of batteries that can be lost. Whether it is applicable or not depends ultimately on the conditions and requirements imposed by users' needs and operational environments, which is, as it has been explained, one of the topics of this Thesis.

On the errors involved in the estimate of glacier ice volume from ice thickness data

The assessment of the glacier thickness is one of the most widespread applications of radioglaciology, and is the basis for estimating the glacier volume. The accuracy of the measurement of ice thickness, the distribution of profiles over the glacier and the accuracy of the boundary delineation of the glacier are the most important factors determining the error in the evaluation of the glacier volume. The aim of this study is to get an accurate estimate of the error incurred in the estimate of glacier volume from GPR-retrieved ice-thickness data.

Estrategia de desarrollo de negocio para el producto Atos RTTF (Real Time Traffic Forecast)

El objetivo del presente proyecto de fin de máster es desplegar la estrategia de negocio completa, desde las declaraciones y premisas hasta la implantación y ejecución, para una solución novedosa de la compañía AtoS. Esta solución se denomina RTTF (Real Time Traffic Forecast), y sus objetivos principales, a alto nivel, son los siguientes: a) Conseguir unas mejores ciudades en la que vivir y trabajar. b) Realizar una gestión de tráfico proactiva para un uso de recursos de las ciudades optimizado. Nuestro planteamiento en este trabajo es, basado en las el módulo de estrategia del máster, diseñar un plan de negocio para desarrollar y potenciar la anterior solución. Para ello también necesitaremos herramientas de otros módulos del máster, como el de marketing, operaciones, o finanzas. Para ello, comenzaremos analizando el entorno desde el punto de vista de la posible receptividad al producto, así como de los posibles competidores, con objeto de posicionar de manera inicial nuestra solución, y reflexionar sobre si ese posicionamiento es el adecuado. Añadiendo también el estudio interno de la compañía y de la propia solución sobre la que versa el proyecto. El principal entregable del presente trabajo será un plan de negocio, con fechas, objetivos y un listado de clientes por orden de prioridad, con el objetivo final de desarrollar la solución.

PV power forecast using a nonparametric PV model

Forecasting the AC power output of a PV plant accurately is important both for plant owners and electric system operators. Two main categories of PV modeling are available: the parametric and the nonparametric. In this paper, a methodology using a nonparametric PV model is proposed, using as inputs several forecasts of meteorological variables from a Numerical Weather Forecast model, and actual AC power measurements of PV plants. The methodology was built upon the R environment and uses Quantile Regression Forests as machine learning tool to forecast AC power with a confidence interval. Real data from five PV plants was used to validate the methodology, and results show that daily production is predicted with an absolute cvMBE lower than 1.3%.