Soluciones de control para el Hogar Digital Accesible

En este proyecto, se pretende obtener la solución óptima para el control del hogar digital accesible. Para ello, comenzaremos explicando el funcionamiento básico de un sistema dómotico, enumeraremos los diversos dispositivos que se utilizan en este tipo de automatizaciones, y comentaremos las diferentes posibilidades con respecto a la arquitectura del sistema. Para elegir la opción más adecuada, se realizará un pequeño estudio a acerca de cada una de las tecnologías existentes, protocolos cerrados, y abiertos, así como tecnologías inalámbricas o de bus. Se realizará un estudio con mayor profundidad del estándar KNX, ya que será una de las tecnologías elegidas finalmente para la realización del proyecto. Una vez elegido el estándar, hemos de centrarnos en las necesidades del recinto, para así poder empezar a definir cada uno de los elementos que incluiremos en nuestra instalación, sensores, actuadores, elementos de intercomunicación, procesadores y dispositivos de control. El siguiente paso consistiría en la programación de la vivienda, para ello hemos de tener previamente estructurados y definidos tanto el número de circuitos eléctricos, como la función que estos desempeñan dentro del recinto inteligente, es decir, accionamiento, regulación etc, para así poder asignar cada circuito a la salida correspondiente de su propio actuador. La vivienda se programará a través de ETS, software asociado a la marca KNX. Mediante este protocolo controlaremos, iluminación, motores, climatización y seguridad. Debido a los recursos limitados que ofrece KNX con respecto a la programación lógica de eventos y secuencias de acciones, y la necesidad de visualizar la interfaz gráfica de la vivienda se ha integrado un procesador. Considerando el deseo de integrar el control de un televisor en la vivienda, futuras ampliaciones y otros aspectos, el procesador integrado será de Crestron Electronics, marca correspondiente a un protocolo cerrado de automatización de sistemas, que cuenta con grandes avances en el control multimedia. Por tanto, la segunda parte de la programación se realizará mediante otros dos softwares diferentes, pertenecientes a la marca, Simple Windows se encargará de la programación lógica del sistema, mientras que Vision Tools creará la visualización. Por último, obtendremos las conclusiones necesarias, adjuntaremos un diagrama de conexionado, presupuesto de la instalación, planos y un pequeño manual de usuario. ABSTRACT. The aim of this project is to optimize the environment control of the Accesible Digital Home unit located in ETSIST - UPM, through different essays, valuing the domestic possibilities and the current interfaces. The tests will be carried out comparing different protocols and the possibilities of optimization that they offer to a Digital Home. Aspects such as: ease the communications with other systems, reliability, costs, long term maintenance of the installation, etc. After conducting trials protocol or most appropriate technology for the automation of the enclosure shall be elected. One Chosen the standard, we have to focus on the needs of the enclosure, so, to begin defining each of the elements included in our installation, sensors, actuators, elements intercom, processors and control devices. The next step is the programing of housing, for that we have previously structured and defined both the number of electrical circuits, as the role they play in the intelligent enclosure, that is, switching, dimming etc., in order to assign each circuit to the corresponding output of its own actuator. The house will be scheduled through ETS, software associated with the brand KNX. Through this protocol we will control, lighting, motors, air conditioning and security. Due to the limited resources available in KNX with respect logic programming of events and sequences of actions, and the need to display the graphical interface housing has been integrated processor belonging to the closed protocol or Crestron electronics brand. Finally, when we get the necessary conclusions, enclose a diagram of wiring, installation budget, planes and a small manual.

Metodología de evaluación de la seguridad vial en intersecciones basada en el análisis cuantitativo de conflictos entre vehículos

El modo tradicional de estimar el nivel de seguridad vial es el registro de accidentes de tráfico, sin embargo son altamente variables, aleatorios y necesitan un periodo de registro de al menos 3 años. Existen metodologías preventivas en las cuales no es necesario que ocurra un accidente para determinar el nivel de seguridad de una intersección, como lo es la técnica de los conflictos de tráfico, que introduce las mediciones alternativas de seguridad como cuantificadoras del riesgo de accidente. El objetivo general de la tesis es establecer una metodología que permita clasificar el riesgo en intersecciones interurbanas, en función del análisis de conflictos entre vehículos, realizado mediante las variables alternativas o indirectas de seguridad vial. La metodología para el análisis y evaluación temprana de la seguridad en una intersección, estará basada en dos medidas alternativas de seguridad: el tiempo hasta la colisión y el tiempo posterior a la invasión de la trayectoria. El desarrollo experimental se realizó mediante estudios de campo, para la parte exploratoria de la investigación, se seleccionaron 3 intersecciones interurbanas en forma de T donde se obtuvieron las variables que caracterizan los conflictos entre vehículos; luego mediante técnicas de análisis multivariante, se obtuvo los modelos de clasificación del riesgo cualitativo y cuantitativo. Para la homologación y el estudio final de concordancia entre el índice propuesto y el modelo de clasificación, se desarrollaron nuevos estudios de campo en 6 intersecciones interurbanas en forma de T. El índice de riesgo obtenido resulta una herramienta muy útil para realizar evaluaciones rápidas conducentes a estimar la peligrosidad de una intersección en T, debido a lo simple y económico que resulta obtener los registros de datos en campo, por medio de una rápida capacitación a operarios; la elaboración del informe de resultados debe ser por un especialista. Los índices de riesgo obtenidos muestran que las variables originales más influyentes son las mediciones de tiempo. Se pudo determinar que los valores más altos del índice de riesgo están relacionados a un mayor riesgo de que un conflicto termine en accidente. Dentro de este índice, la única variable cuyo aporte es proporcionalmente directo es la velocidad de aproximación, lo que concuerda con lo que sucede en un conflicto, pues una velocidad excesiva se manifiesta como un claro factor de riesgo ya que potencia todos los fallos humanos en la conducción. Una de las principales aportaciones de esta tesis doctoral a la ingeniería de carreteras, es la posibilidad de aplicación de la metodología por parte de administraciones de carreteras locales, las cuales muchas veces cuentan con recursos de inversión limitados para efectuar estudios preventivos, sobretodo en países en vías de desarrollo. La evaluación del riesgo de una intersección luego de una mejora en cuanto a infraestructura y/o dispositivos de control de tráfico, al igual que un análisis antes – después, pero sin realizar una comparación mediante la ocurrencia de accidentes, sino que por medio de la técnica de conflictos de tráfico, se puede convertir en una aplicación directa y económica. Además, se pudo comprobar que el análisis de componentes principales utilizado en la creación del índice de riesgo de la intersección, es una herramienta útil para resumir todo el conjunto de mediciones que son posibles de obtener con la técnica de conflictos de tráfico y que permiten el diagnóstico del riesgo de accidentalidad en una intersección. En cuanto a la metodología para la homologación de los modelos, se pudo establecer la validez y confiabilidad al conjunto de respuestas entregadas por los observadores en el registro de datos en campo, ya que los resultados de la validación establecen que la medición de concordancia de las respuestas entregadas por los modelos y lo observado, son significativas y sugieren una alta coincidencia entre ellos. ABSTRACT The traditional way of estimating road safety level is the record of occurrence of traffic accidents; however, they are highly variable, random, and require a recording period of at least three years. There are preventive methods which do not need an accident to determine the road safety level of an intersection, such as traffic conflict technique, which introduces surrogate safety measures as parameters for the evaluation of accident risks. The general objective of the thesis is to establish a methodology that will allow the classification of risk at interurban intersections as a function of the analysis of conflicts between vehicles performed by means of surrogate road safety variables. The proposal of a methodology for the analysis and early evaluation of safety at an intersection will be based on two surrogate safety measures: the time to collision and the post encroachment time. On the other hand, the experimental development has taken place by means of field studies in which the exploratory part of the investigation selected three interurban T-intersections where the application of the traffic conflict technique gave variables that characterize the conflicts between vehicles; then, using multivariate analysis techniques, the models for the classification of qualitative and quantitative risk were obtained. With the models new field studies were carried out at six interurban Tintersections with the purpose of developing the homologation and the final study of the agreement between the proposed index and the classification model. The risk index obtained is a very useful tool for making rapid evaluations to estimate the hazard of a T-intersection, as well as for getting simply and economically the field data records after a fast training of the workers and then preparing the report of results by a specialist. The risk indices obtained show that the most influential original variables are the measurements of time. It was determined that the highest risk index values are related with greater risk of a conflict resulting in an accident. Within this index, the only variable whose contribution is proportionally direct is the approach speed, in agreement with what happens in a conflict, because excessive speed appears as a clear risk factor at an intersection because it intensifies all the human driving faults. One of the main contributions of this doctoral thesis to road engineering is the possibility of applying the methodology by local road administrations, which very often have limited investment resources to carry out these kinds of preventive studies, particularly in developing countries. The evaluation of the risk at an intersection after an improvement in terms of infrastructure and/or traffic control devices, the same as a before/after analysis, without comparison of accident occurrence but by means of the traffic conflict technique, can become a direct and economical application. It is also shown that main components analysis used for producing the risk index of the intersection is a useful tool for summarizing the whole set of measurements that can be obtained with the traffic conflict technique and allow diagnosing accident risk at an intersection. As to the methodology for the homologation of the models, the validity and reliability of the set of responses delivered by the observers recording the field data could be established, because the results of the validation show that agreement between the observations and the responses delivered by the models is significant and highly coincident.

A Propose-and-revise System for Real-time Traffic Management

The aim of this paper is to describe an intelligent system for the problem of real time road traffic control. The purpose of the system is to help traffic engineers in the selection of the state of traffic control devices on real time, using data recorded by traffic detectors on motorways. The system follows an advanced knowledge-based approach that implements an abstract generic problem solving method, called propose-and-revise, which was proposed in Artificial Intelligence, within the knowledge engineering field, as a standard cognitive structure oriented to solve configuration design problems. The paper presents the knowledge model of such a system together with the strategy of inference and describes how it was applied for the case of the M-40 urban ring for the city of Madrid.

Design and control of multi-finger haptic devices for dexterous manipulation

En la interacción con el entorno que nos rodea durante nuestra vida diaria (utilizar un cepillo de dientes, abrir puertas, utilizar el teléfono móvil, etc.) y en situaciones profesionales (intervenciones médicas, procesos de producción, etc.), típicamente realizamos manipulaciones avanzadas que incluyen la utilización de los dedos de ambas manos. De esta forma el desarrollo de métodos de interacción háptica multi-dedo dan lugar a interfaces hombre-máquina más naturales y realistas. No obstante, la mayoría de interfaces hápticas disponibles en el mercado están basadas en interacciones con un solo punto de contacto; esto puede ser suficiente para la exploración o palpación del entorno pero no permite la realización de tareas más avanzadas como agarres. En esta tesis, se investiga el diseño mecánico, control y aplicaciones de dispositivos hápticos modulares con capacidad de reflexión de fuerzas en los dedos índice, corazón y pulgar del usuario. El diseño mecánico de la interfaz diseñada, ha sido optimizado con funciones multi-objetivo para conseguir una baja inercia, un amplio espacio de trabajo, alta manipulabilidad y reflexión de fuerzas superiores a 3 N en el espacio de trabajo. El ancho de banda y la rigidez del dispositivo se han evaluado mediante simulación y experimentación real. Una de las áreas más importantes en el diseño de estos dispositivos es el efector final, ya que es la parte que está en contacto con el usuario. Durante este trabajo se ha diseñado un dedal de bajo peso, adaptable a diferentes usuarios que, mediante la incorporación de sensores de contacto, permite estimar fuerzas normales y tangenciales durante la interacción con entornos reales y virtuales. Para el diseño de la arquitectura de control, se estudiaron los principales requisitos para estos dispositivos. Entre estos, cabe destacar la adquisición, procesado e intercambio a través de internet de numerosas señales de control e instrumentación; la computación de equaciones matemáticas incluyendo la cinemática directa e inversa, jacobiana, algoritmos de detección de agarres, etc. Todos estos componentes deben calcularse en tiempo real garantizando una frecuencia mínima de 1 KHz. Además, se describen sistemas para manipulación de precisión virtual y remota; así como el diseño de un método denominado "desacoplo cinemático iterativo" para computar la cinemática inversa de robots y la comparación con otros métodos actuales. Para entender la importancia de la interacción multimodal, se ha llevado a cabo un estudio para comprobar qué estímulos sensoriales se correlacionan con tiempos de respuesta más rápidos y de mayor precisión. Estos experimentos se desarrollaron en colaboración con neurocientíficos del instituto Technion Israel Institute of Technology. Comparando los tiempos de respuesta en la interacción unimodal (auditiva, visual y háptica) con combinaciones bimodales y trimodales de los mismos, se demuestra que el movimiento sincronizado de los dedos para generar respuestas de agarre se basa principalmente en la percepción háptica. La ventaja en el tiempo de procesamiento de los estímulos hápticos, sugiere que los entornos virtuales que incluyen esta componente sensorial generan mejores contingencias motoras y mejoran la credibilidad de los eventos. Se concluye que, los sistemas que incluyen percepción háptica dotan a los usuarios de más tiempo en las etapas cognitivas para rellenar información de forma creativa y formar una experiencia más rica. Una aplicación interesante de los dispositivos hápticos es el diseño de nuevos simuladores que permitan entrenar habilidades manuales en el sector médico. En colaboración con fisioterapeutas de Griffith University en Australia, se desarrolló un simulador que permite realizar ejercicios de rehabilitación de la mano. Las propiedades de rigidez no lineales de la articulación metacarpofalange del dedo índice se estimaron mediante la utilización del efector final diseñado. Estos parámetros, se han implementado en un escenario que simula el comportamiento de la mano humana y que permite la interacción háptica a través de esta interfaz. Las aplicaciones potenciales de este simulador están relacionadas con entrenamiento y educación de estudiantes de fisioterapia. En esta tesis, se han desarrollado nuevos métodos que permiten el control simultáneo de robots y manos robóticas en la interacción con entornos reales. El espacio de trabajo alcanzable por el dispositivo háptico, se extiende mediante el cambio de modo de control automático entre posición y velocidad. Además, estos métodos permiten reconocer el gesto del usuario durante las primeras etapas de aproximación al objeto para su agarre. Mediante experimentos de manipulación avanzada de objetos con un manipulador y diferentes manos robóticas, se muestra que el tiempo en realizar una tarea se reduce y que el sistema permite la realización de la tarea con precisión. Este trabajo, es el resultado de una colaboración con investigadores de Harvard BioRobotics Laboratory. ABSTRACT When we interact with the environment in our daily life (using a toothbrush, opening doors, using cell-phones, etc.), or in professional situations (medical interventions, manufacturing processes, etc.) we typically perform dexterous manipulations that involve multiple fingers and palm for both hands. Therefore, multi-Finger haptic methods can provide a realistic and natural human-machine interface to enhance immersion when interacting with simulated or remote environments. Most commercial devices allow haptic interaction with only one contact point, which may be sufficient for some exploration or palpation tasks but are not enough to perform advanced object manipulations such as grasping. In this thesis, I investigate the mechanical design, control and applications of a modular haptic device that can provide force feedback to the index, thumb and middle fingers of the user. The designed mechanical device is optimized with a multi-objective design function to achieve a low inertia, a large workspace, manipulability, and force-feedback of up to 3 N within the workspace; the bandwidth and rigidity for the device is assessed through simulation and real experimentation. One of the most important areas when designing haptic devices is the end-effector, since it is in contact with the user. In this thesis the design and evaluation of a thimble-like, lightweight, user-adaptable, and cost-effective device that incorporates four contact force sensors is described. This design allows estimation of the forces applied by a user during manipulation of virtual and real objects. The design of a real-time, modular control architecture for multi-finger haptic interaction is described. Requirements for control of multi-finger haptic devices are explored. Moreover, a large number of signals have to be acquired, processed, sent over the network and mathematical computations such as device direct and inverse kinematics, jacobian, grasp detection algorithms, etc. have to be calculated in Real Time to assure the required high fidelity for the haptic interaction. The Hardware control architecture has different modules and consists of an FPGA for the low-level controller and a RT controller for managing all the complex calculations (jacobian, kinematics, etc.); this provides a compact and scalable solution for the required high computation capabilities assuring a correct frequency rate for the control loop of 1 kHz. A set-up for dexterous virtual and real manipulation is described. Moreover, a new algorithm named the iterative kinematic decoupling method was implemented to solve the inverse kinematics of a robotic manipulator. In order to understand the importance of multi-modal interaction including haptics, a subject study was carried out to look for sensory stimuli that correlate with fast response time and enhanced accuracy. This experiment was carried out in collaboration with neuro-scientists from Technion Israel Institute of Technology. By comparing the grasping response times in unimodal (auditory, visual, and haptic) events with the response times in events with bimodal and trimodal combinations. It is concluded that in grasping tasks the synchronized motion of the fingers to generate the grasping response relies on haptic cues. This processing-speed advantage of haptic cues suggests that multimodalhaptic virtual environments are superior in generating motor contingencies, enhancing the plausibility of events. Applications that include haptics provide users with more time at the cognitive stages to fill in missing information creatively and form a richer experience. A major application of haptic devices is the design of new simulators to train manual skills for the medical sector. In collaboration with physical therapists from Griffith University in Australia, we developed a simulator to allow hand rehabilitation manipulations. First, the non-linear stiffness properties of the metacarpophalangeal joint of the index finger were estimated by using the designed end-effector; these parameters are implemented in a scenario that simulates the behavior of the human hand and that allows haptic interaction through the designed haptic device. The potential application of this work is related to educational and medical training purposes. In this thesis, new methods to simultaneously control the position and orientation of a robotic manipulator and the grasp of a robotic hand when interacting with large real environments are studied. The reachable workspace is extended by automatically switching between rate and position control modes. Moreover, the human hand gesture is recognized by reading the relative movements of the index, thumb and middle fingers of the user during the early stages of the approximation-to-the-object phase and then mapped to the robotic hand actuators. These methods are validated to perform dexterous manipulation of objects with a robotic manipulator, and different robotic hands. This work is the result of a research collaboration with researchers from the Harvard BioRobotics Laboratory. The developed experiments show that the overall task time is reduced and that the developed methods allow for full dexterity and correct completion of dexterous manipulations.

Modelling and Simulation of Moored Devices for Ocean Currents Energy Harnessing

The main objective of this paper is the presentation of modelling solutions off loating devices that can be used for harnessing energy from ocean currents. It has been structured into three main parts. First, the growing current interest in marine renewable energy in general, and in extracting energy from currents in particular, is presented, showing the large number of solutions that are emerging and some of the most significant types. GESMEY generator is presented in second section. It is based on a new concept that has been patented by the Universidad Politécnica de Madrid and which is currently being developed through a collaborative agreement with the SOERMAR Foundation. The main feature of this generator is that on operation is fully submerged, and no other facilities are required to move to floating state for maintenance, which greatly increases its performance. Third part of the article is devoted to present the modelling and simulation challenges that arise in the development of devices for harnessing the energy of marine currents, along with some solutions which have been adopted within the frame of the GESMEY Project, making particular emphasis on the dynamics of the generator and its control

Enhancing Interaction With Smart Objects Throught Mobile Devices

Interaction with smart objects can be accomplished with different technologies, such as tangible interfaces or touch computing, among others. Some of them require the object to be especially designed to be 'smart', and some other are limited in the variety and complexity of the possible actions. This paper describes a user-smart object interaction model and prototype based on the well known event-condition-action (ECA) reasoning, which can work, to a degree, independently of the intelligence embedded into the smart object. It has been designed for mobile devices to act as mediators between users and smart objects and provides an intuitive means for personalization of object's behavior. When the user is close to an object, this one publishes its 'event & action' capabilities to the user's device. The user may accept the object's module offering, which will enable him to configure and control that object, but also its actions with respect to other elements of the environment or the virtual world. The modular ECA interaction model facilitates the integration of different types of objects in a smart space, giving the user full control of their capabilities and facilitating creative mash-uping to build customized functionalities that combine physical and virtual actions

Red Multihaz de Desfase Escalonado para el Control de un Array de Antenas.

This paper presents a general systems that can be taken into account to control between elements in an antenna array. Because the digital phase shifter devices have become a strategic element and also some steps have been taken for their export by U.S. Government, this element has increased its price to the low supply in the market. Therefore, it is necessary to adopt some solutions that allow us to deal with the design and construction of antenna arrays. system based on a group of a staggered phase shift with external switching is shown, which is extrapolated array.

Processing and adsorption control in ZnO single nanowire photodetectors

ZnO single nanowire photodetectors have been measured in different ambient conditions in order to understand and control adsorption processes on the surface. A decrease in the conductivity has been observed as a function of time when the nanowires are exposed to air, due to adsorbed O2/H2O species at the nanowire surface. In order to have a device with stable characteristics in time, thermal desorption has been used to recover the original conductivity followed by PMMA coating of the exposed nanowire surface.

Study of the effect of blurriness in image acquisition for Hand Biometrics in Mobile Devices

This paper presents a study on the effect of blurred images in hand biometrics. Blurred images simulates out-of-focus effects in hand image acquisition, a common consequence of unconstrained, contact-less and platform-free hand biometrics in mobile devices. The proposed biometric system presents a hand image segmentation based on multiscale aggregation, a segmentation method invariant to different changes like noise or blurriness, together with an innovative feature extraction and a template creation, oriented to obtain an invariant performance against blurring effects. The results highlight that the proposed system is invariant to some low degrees of blurriness, requiring an image quality control to detect and correct those images with a high degree of blurriness. The evaluation has considered a synthetic database created based on a publicly available database with 120 individuals. In addition, several biometric techniques could benefit from the approach proposed in this paper, since blurriness is a very common effect in biometric techniques involving image acquisition.

An approach to hand biometrics in mobile devices

This paper focuses on hand biometrics applied to images acquired from a mobile device. The system offers the possibility of identifying individuals based on features extracted from hand pictures obtained with a low-quality camera embedded on a mobile device. Furthermore, the acquisitions have been carried out regardless illumination control, orientation, distance to camera, and similar aspects. In addition, the whole system has been tested with an owned database. Finally, the results obtained (6.0% ± 0.2) and the algorithm structure are both promising in relation to a posterior mobile implementation

Sistemas de control de roturas en presas y caracterización de sistemas hidráulicos

Este proyecto nace de la necesidad de automatizar el estudio de sistemas hidráulicos y de control de roturas en presas. Para realizar el estudio de sistemas hidráulicos se usarán un número indeterminado de sensores de nivel, presión y caudal. El número de sensores que se pueden utilizar viene determinado por el material disponible. Estos sensores se conectarán a unas tarjetas de National Instruments modelo NI 9208 y éstas a su vez a un chasis modelo CompactDAQ NI-9174 con cuatro ranuras. Conectando este chasis al ordenador podremos obtener los datos provenientes de los sensores. También se podrá controlar una válvula para determinar la cantidad de agua que fluye en nuestro experimento. Está válvula está conectada a una tarjeta NI-9264 que se conectará al chasis en su última posición Para detectar y estudiar posibles roturas en presas se dispone de un motor y un láser con los cuales se puede barrer la superficie de una presa y obtener una imagen en tres dimensiones de la misma procesando los datos provenientes del laser. Para recoger los datos de los sensores y controlar una válvula se ha desarrollado una aplicación utilizando LabVIEW, un programa creado por National Instruments. Para poder controlar el motor y el láser se parte de una aplicación que ya estaba realizada en LabVIEW. El objetivo ha sido detectar y corregir una serie de errores en la misma. Dentro del proyecto, además de la explicación detallada de la aplicación para los sensores y la válvula, y las pruebas realizadas para detectar y corregir los errores de la aplicación del láser y el motor, existe: una breve introducción a la programación en LabVIEW, la descripción de los pasos realizados para el conexionado de los sensores con las tarjetas, los manuales de usuario de las aplicaciones y la descripción de los equipos utilizados. This project stars from the need to automate the study of hydraulic systems and control dam breaks. For the study of hydraulic systems it will be used an unspecified number of level, pressure and flow sensors. The number of sensors that can be used is determined by the available material. These sensors are connected to a NI 9208 National Instruments target and these cards to a NI-9174 CompactDAQ chassis with four slots. Connecting the chassis to a computer we will obtain data from the sensors. We also can control a valve to determine the amount of water flowing in our experiment. This valve is connected to a NI-9264 card and this card to the last position of the chassis. To detect and study dams breakage it used a motor and a laser. With these two devices we can scan the surface of a dam and obtain a three-dimensional image processing data from the laser. To collect data from the sensors and control the valve it has developed an application using LabVIEW, a program created by National Instruments. To control the motor and the laser it is used an application that was already created using LabVIEW. The aim of this part has been detect and correct a number of errors in this application. Within the project, in addition to the detailed explanation of the application for sensors and valve, and tests to detect and correct errors in the application of lasers and the motor, there is: a brief introduction to programming in LabVIEW, the description of the steps taken for connecting the sensors with cards, user manuals and application description of the equipment used.

Performance of pressure control valves and flow meters precision in operational irrigation-water balance accuracy

In pressure irrigation-water distribution networks, pressure regulating devices for controlling the discharged flow rate by irrigation units are needed due to the variability of flow rate. In addition, applied water volume is used controlled operating the valve during a calculated time interval, and assuming constant flow rate. In general, a pressure regulating valve PRV is the commonly used pressure regulating device in a hydrant, which, also, executes the open and close function. A hydrant feeds several irrigation units, requiring a wide range in flow rate. In addition, some flow meters are also available, one as a component of the hydrant and the rest are placed downstream. Every land owner has one flow meter for each group of field plots downstream the hydrant. Its lecture could be used for refining the water balance but its accuracy must be taken into account. Ideal PRV performance would maintain a constant downstream pressure. However, the true performance depends on both upstream pressure and the discharged flow rate. The objective of this work is to asses the influence of the performance on the applied volume during the whole irrigation events in a year. The results of the study have been obtained introducing the flow rate into a PRV model. Variations on flow rate are simulated by taking into account the consequences of variations on climate conditions and also decisions in irrigation operation, such us duration and frequency application. The model comprises continuity, dynamic and energy equations of the components of the PRV.

New control architecturebased on PXI for a 3-finger haptic device applied to virtual manipulation

To perform advanced manipulation of remote environments such as grasping, more than one finger is required implying higher requirements for the control architecture. This paper presents the design and control of a modular 3-finger haptic device that can be used to interact with virtual scenarios or to teleoperate dexterous remote hands. In a modular haptic device, each module allows the interaction with a scenario by using a single finger; hence, multi-finger interaction can be achieved by adding more modules. Control requirements for a multifinger haptic device are analyzed and new hardware/software architecture for these kinds of devices is proposed. The software architecture described in this paper is distributed and the different modules communicate to allow the remote manipulation. Moreover, an application in which this haptic device is used to interact with a virtual scenario is shown.

Effect of reservoir tillage on rainwater harvesting and soil erosion control under a developed rainfall simulator.

Soil erosion is a serious environmental threat in the Mediterranean region due to torrential rainfalls, and it contributes to the degradation of agricultural land. Techniques such as rainwater harvesting may improve soil water storage and increase agricultural productivity, which could result in more effective land usage. Reservoir tillage is an effective system of harvesting rainwater, but it has not been scientifically evaluated like other tillage systems. Its suitability for the conditions in Spain has not been determined. To investigate and quantify water storage from reservoir tillage and how it could be adapted to improve infiltration of harvested rainwater, a laboratory-scale rainfall simulator was developed. Rainfall characteristics, including rainfall intensity, spatial uniformity and raindrop size, confirm that natural rainfall conditions are simulated with sufficient accuracy. The simulator was auto-controlled by a solenoid valve and three pressure nozzles were used to spray water corresponding to five rainfall intensities ranging from 36 to 112 mm h-1 for 3 to 101-year return period with uniformity coefficients between 83 and 94%. In order to assess the reservoir tillage method under surface slopes of 0, 5, and 10%, three soil scooping devices with identical volume were used to make depressions in the following forms: a) truncated square pyramid, b) triangular prism, and c) truncated cone. These depressions were compared to a control soil surface with no depression. For the loam soil used in this study, results show that reservoir tillage was able to reduce soil erosion and surface runoff and significantly increase infiltration. There was significant difference between the depressions and the control. Compared to the control, depression (a) reduced surface runoff by about 61% and the sediment yield concentration by about 79%.

Optical regeneration based on noise generated in bistable devices: going from 2R to 3R

In this paper we propose to employ an instability that occurs in bistable devices as a control signal at the reception stage to generate the clock signal. One of the adopted configurations is composed of two semiconductor optical amplifiers arranged in a cascaded structure. This configuration has an output equivalent to that obtained from Self-Electrooptic Effect Devices (SEEDs), and it can implement the main Boolean functions of two binary inputs. These outputs, obtained from the addition of two binary signals, show a short spike in the transition from "1" to "2" in the internal processing. A similar result is obtained for a simple semiconductor amplifier with bistable behavior. The paper will show how these structures may help recover clock signals in any optical transmission system