Container Terminal Simulation. A case study: port of Valencia.

This paper is concerned with the study of non-Markovian queuing systems in container terminals. The methodology presented has been applied to analyze the ship traffic in the port of Valencia located in the Western Mediterranean. Two container terminals have been studied: the public container terminal of NOATUM and the dedicated container terminal of MSC. This paper contains the results of a simulation model based on queuing theory. The methodology presented is found to be effective in replicating realistic ship traffic operations in port as well as in conducting capacity evaluations. Thus the methodology can be used for capacity planning (long term), tactical planning (medium term) and even for the container terminal design (port enlargement purposes).

Berth Management in Container Terminals: Quality of Service

This paper empirically evaluates container terminal service attributes. The methodology proposed focuses on statistical control. Based on the concept of service segmentation, the authors employed control charts to classify container terminal services. The purpose of control charts is to allow simple detection of events that are indicative of actual process change. This simple decision can be difficult where the process characteristic is continuously varying, the control chart provides statistically objective criteria of change. When change is detected and considered good its cause should be identified and possibly become the new way of working, where the change is bad then its cause should be identified and eliminated. Both theoretical and practical implications of the research findings are discussed in this paper.

Berth management in container terminals: quality of service

This paper empirically evaluates container terminal service attributes. The methodology proposed focuses on statistical control. Based on the concept of service segmentation, we employed control charts to classify container terminal services. The purpose of control charts is to allow simple detection of events that are indicative of actual process change. This simple decision can be difficult where the process characteristic is continuously varying; the control chart provides statistically objective criteria of change. When change is detected and considered good its cause should be identified and possibly become the new way of working, where the change is bad then its cause should be identified and eliminated. This paper is organized as follows: Section 1 is the introduction, Section 2 provides a brief note on other studies that inspired this research, section 3 focuses on the methodology used, and develops the results obtained and finally conclusions are shown in Section 4. Theoretical and practical implications of the research findings are discussed.

Neutron spectra and dosimetric assessment around a neutron Howitzer container

The neutron Howitzer container at the Neutron Measurements Laboratory of the Nuclear Engineering Department of the Polytechnic University of Madrid (UPM), is equipped with a 241Am-Be neutron source of 74 GBq in its center. The container allows the source to be in either the irradiation or the storage position. To measure the neutron fluence rate spectra around the Howitzer container, measurements were performed using a Bonner spheres spectrometer and the spectra were unfolded using the NSDann program. A calibrated neutron area monitor LB6411 was used to measure the ambient dose equivalent rates, H*(10). Detailed Monte-Carlo simulations were performed to calculate the measured quantities at the same positions. The maximum relative deviation between simulations and measurements was 19.53%. After validation, the simulated model was used to calculate the equivalent dose rate in several key organs of a voxel phantom. The computed doses in the skin and lenses of the eyes are within the ICRP recommended dose limits, as is the H*(10) value for the storage position.

A methodology proposal to obtain operational parameter forecasts and operational risk assessment in container terminals

Las terminales de contenedores son sistemas complejos en los que un elevado número de actores económicos interactúan para ofrecer servicios de alta calidad bajo una estricta planificación y objetivos económicos. Las conocidas como "terminales de nueva generación" están diseñadas para prestar servicio a los mega-buques, que requieren tasas de productividad que alcanzan los 300 movimientos/ hora. Estas terminales han de satisfacer altos estándares dado que la competitividad entre terminales es elevada. Asegurar la fiabilidad de las planificaciones del atraque es clave para atraer clientes, así como reducir al mínimo el tiempo que el buque permanece en el puerto. La planificación de las operaciones es más compleja que antaño, y las tolerancias para posibles errores, menores. En este contexto, las interrupciones operativas deben reducirse al mínimo. Las principales causas de dichas perturbaciones operacionales, y por lo tanto de incertidumbre, se identifican y caracterizan en esta investigación. Existen una serie de factores que al interactuar con la infraestructura y/o las operaciones desencadenan modos de fallo o parada operativa. Los primeros pueden derivar no solo en retrasos en el servicio sino que además puede tener efectos colaterales sobre la reputación de la terminal, o incluso gasto de tiempo de gestión, todo lo cual supone un impacto para la terminal. En el futuro inmediato, la monitorización de las variables operativas presenta gran potencial de cara a mejorar cualitativamente la gestión de las operaciones y los modelos de planificación de las terminales, cuyo nivel de automatización va en aumento. La combinación del criterio experto con instrumentos que proporcionen datos a corto y largo plazo es fundamental para el desarrollo de herramientas que ayuden en la toma de decisiones, ya que de este modo estarán adaptadas a las auténticas condiciones climáticas y operativas que existen en cada emplazamiento. Para el corto plazo se propone una metodología con la que obtener predicciones de parámetros operativos en terminales de contenedores. Adicionalmente se ha desarrollado un caso de estudio en el que se aplica el modelo propuesto para obtener predicciones de la productividad del buque. Este trabajo se ha basado íntegramente en datos proporcionados por una terminal semi-automatizada española. Por otro lado, se analiza cómo gestionar, evaluar y mitigar el efecto de las interrupciones operativas a largo plazo a través de la evaluación del riesgo, una forma interesante de evaluar el effecto que eventos inciertos pero probables pueden generar sobre la productividad a largo plazo de la terminal. Además se propone una definición de riesgo operativo junto con una discusión de los términos que representan con mayor fidelidad la naturaleza de las actividades y finalmente, se proporcionan directrices para gestionar los resultados obtenidos. Container terminals are complex systems where a large number of factors and stakeholders interact to provide high-quality services under rigid planning schedules and economic objectives. The socalled next generation terminals are conceived to serve the new mega-vessels, which are demanding productivity rates up to 300 moves/hour. These terminals need to satisfy high standards because competition among terminals is fierce. Ensuring reliability in berth scheduling is key to attract clients, as well as to reduce at a minimum the time that vessels stay the port. Because of the aforementioned, operations planning is becoming more complex, and the tolerances for errors are smaller. In this context, operational disturbances must be reduced at a minimum. The main sources of operational disruptions and thus, of uncertainty, are identified and characterized in this study. External drivers interact with the infrastructure and/or the activities resulting in failure or stoppage modes. The later may derive not only in operational delays but in collateral and reputation damage or loss of time (especially management times), all what implies an impact for the terminal. In the near future, the monitoring of operational variables has great potential to make a qualitative improvement in the operations management and planning models of terminals that use increasing levels of automation. The combination of expert criteria with instruments that provide short- and long-run data is fundamental for the development of tools to guide decision-making, since they will be adapted to the real climatic and operational conditions that exist on site. For the short-term a method to obtain operational parameter forecasts in container terminals. To this end, a case study is presented, in which forecasts of vessel performance are obtained. This research has been entirely been based on data gathered from a semi-automated container terminal from Spain. In the other hand it is analyzed how to manage, evaluate and mitigate disruptions in the long-term by means of the risk assessment, an interesting approach to evaluate the effect of uncertain but likely events on the long-term throughput of the terminal. In addition, a definition for operational risk evaluation in port facilities is proposed along with a discussion of the terms that better represent the nature of the activities involved and finally, guidelines to manage the results obtained are provided.

Multi-distributed wireless sensors for monitoring a long distance transport in a reefer container

The study of the temperature gradients in cold stores and containers is a critical issue in the food industry for the quality assurance of products during transport and for minimising losses. This work presents an analysis of the temperatures during the refrigerated transport of 4,320 kg of blueberries in a reefer (set point temperature at ?1ºC) on a container ship from Montevideo (Uruguay) to Verona (Italy). The monitoring was performed by using semi-passive RFID loggers (TurboTag cards). The objective was to carry out a multi-distributed supervision using low-cost, wireless and autonomous sensors for the characterisation of the distribution and spatial gradients of temperatures during a long distance transport. Data analysis shows spatial (phase space) and temporal sequencing diagrams and reveals a significant heterogeneity of temperature at different locations in the container, which highlights the ineffectiveness of a temperature control system based on a single sensor, as is usually done.

Arsenic, antimony and selenium in urban soils: potential risks for human health in urban gardening

The benefits of urban agriculture are many and well documented, ranging from health improvement to community betterment, more sustainable urban development and environment protection. On the negative side, urban soils are commonly enriched in toxic trace elements that have accumulated over time through the deposition of atmospheric particles (generated by automotive traffic, heating systems, historical industrial activities and resuspended street dust), and the uncontrolled disposal of domestic, commercial and industrial wastes. This in turn has given rise to concerns about the level of exposure of urban farmers to these elements and the potential health hazards associated with this exposure. Research efforts in this field have started relatively recently and have almost systematically omitted the influence of Sb and Se, and to a lesser extent of As, although all three have proven toxic effects.

Simulation of Freight Trains Equipped with Partially Filled Tank Containers and Related Resonance Phenomenon

To study the fluid motion-vehicle dynamics interaction, a model of four, liquid filled two-axle container freight wagons was set up. The railway vehicle has been modelled as a multi-body system (MBS). To include fluid sloshing, an equivalent mechanical model has been developed and incorporated. The influence of several factors has been studied in computer simulations, such as track defects, curve negotiation, train velocity, wheel wear, liquid and solid wagonload, and container baffles. SIMPACK has been used for MBS analysis, and ANSYS for liquid sloshing modelling and equivalent mechanical systems validation. Acceleration and braking manoeuvres of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. The coupling gear consists of UIC standard traction hooks and coupling screws that are located between buffers. One of the coupling screws is placed in the traction hook of the opposite wagon thus joining the two wagons, whereas the unused coupling screw rests on a hanger. Simulation results showed that, for certain combinations of type of liquid, filling level and container dimensions, the liquid cargo could provoke an undesirable, although not hazardous, release of the unused coupling screw from its hanger. The coupling screw's release was especially obtained when a period of acceleration was followed by an abrupt braking manoeuvre at 1 m/s2. It was shown that a resonance effect between the liquid's oscillation and the coupling screw's rotary motion could be the reason for the coupling screw's undesired release. Possible solutions to avoid the phenomenon are given.Acceleration and braking manoeuvres of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. The coupling gear consists of UIC standard traction hooks and coupling screws that are located between buffers. One of the coupling screws is placed in the traction hook of the opposite wagon thus joining the two wagons, whereas the unused coupling screw rests on a hanger. This paper reports on a study of the fluid motion-train vehicle dynamics interaction. In the study, a model of four, liquid-filled two-axle container freight wagons was developed. The railway vehicle has been modeled as a multi-body system (MBS). To include fluid sloshing, an equivalent mechanical model has been developed and incorporated. The influence of several factors has been studied in computer simulations, such as track defects, curve negotiation, train velocity, wheel wear, liquid and solid wagonload, and container baffles. A simulation program was used for MBS analysis, and a finite element analysis program was used for liquid sloshing modeling and equivalent mechanical systems validation. Acceleration and braking maneuvers of the freight train set the liquid cargo into motion. This longitudinal sloshing motion of the fluid cargo inside the tanks initiated a swinging motion of some components of the coupling gear. Simulation results showed that, for certain combinations of type of liquid, filling level and container dimensions, the liquid cargo could provoke an undesirable, although not hazardous, release of an unused coupling screw from its hanger. It was shown that a resonance effect between the liquid's oscillation and the coupling screw's rotary motion could be the reason for the coupling screw's undesired release. Solutions are suggested to avoid the resonance problem, and directions for future research are given.

De la ciudad en vibración al ser resonante: Una investigación a propósito de los conciertos de campanas de Llorenç Barber

Este trabajo tiene la vocación de dibujar el mapa de los dominios de oportunidad que hay a disposición de un arquitecto, al imaginar el aspecto sonoro de la ciudad en relación con la campana. Muchas de las dimensiones señaladas, tanto conocidas como desconocidas, son sencillamente despertadas al estudio de lo que un diseñador del espacio sonoro, como Llorenç Barber, viene a decirnos, desde una disciplina aparentemente contactada, pero muchas veces paralela a la arquitectónica. Tomando los conciertos de campanas celebrados hasta la fecha como puestas en práctica real de la condición instrumental de más de doscientas ciudades de todo el mundo, el estudio analiza los hallazgos, éxitos y fracasos, obtenidos a lo largo de estos últimos veinticinco años de experiencia, como resultados explícitos de un trabajo sonoro en la ciudad, probado, contrastado y afinado, del que extraer indicaciones concretas susceptibles de ser aplicadas en el diseño del espacio urbano. Mediante un análisis triangular de vértices definidos: emisor-campana, medio-ciudad, receptor-ciudadano; la investigación aborda los aspectos relativos a la producción y recepción del fenómeno sonoro generado por la campana en la ciudad. En relación con la producción, una parte del trabajo se dedica al estudio de los efectos acústicos observados, ordenado por escalas graduales en las que se produce una distribución del sonido susceptible de diseño: el vaso de la campana, la sala de campanas, el campanario, el cuerpo del edificio, la ciudad y el territorio. A modo de cajas de resonancia y leídas como muñecas rusas, unas dentro de otras, los espacios identificados muestran cualidades sonoras específicas, definidas tanto por sus condiciones geométricas, formales, constructivas o de uso; como por las correspondientes a las subsiguientes cajas que alojan. A fin de esclarecer la influencia de tales cuestiones en el aspecto sonoro de la ciudad, se propone un modelo ordenado de conexión y desconexión de escalas, utilizando una paramétrica puramente técnica creada ex profeso, junto con variables metodológicas más tradicionales. Al mismo tiempo, y tratando de esclarecer cómo, al ser puesta en vibración, la ciudad es aprehendida, disfrutada y rememorada por el ciudadano-oyente, otra parte del trabajo se dedica al estudio de los aspectos relativos a su recepción aural en deambulación compartida. En este caso la investigación se propone reclamar otras dimensiones más subversivas que, si bien escapan a los modos habituales de trabajar del arquitecto, se revelan intensamente en la experiencia plurifocal, multiplicando los efectos a considerar: efectos funcionales y significativos, de reconocimiento, integración y pertenencia a un cuerpo territorial y social de coordenadas históricas y geográficas de nuevo significadas; efectos perceptuales de inmersión, ubicuidad, temporalidad o inestabilidad; efectos estéticos, de rememoración, interpretación simbólica y recreación poética; e incluso efectos políticos, descubriendo un espacio urbano en continua regeneración, lugar para la exposición en su doble acepción, para la exhibición y el peligro, o como contenedor situacional del más profundo sentido ciudadano. Para afinar la relevancia de lo obtenido en cada una de las dimensiones señaladas, el trabajo se articula en tres aproximaciones graduales: el corpus general de los conciertos celebrados hasta la fecha; los conciertos celebrados en España; los tres conciertos para Madrid: Magna Mater (1991), Festi Clamores (2000) y Aurea Catena (2007). Si bien el modelo propuesto nace a la luz de los conciertos de campanas de Llorenç Barber, a escala de una ciudad entera y con una intención compositiva individual, se entiende que sería útil para el uso ordenado de cualquier profesional interesado en el aspecto sonoro de la ciudad, faceta escasamente atendida, dicho sea de paso, desde la disciplina arquitectónica. ABSTRACT This work has the vocation of drawing out the numerous opportunities an architect has at his disposal, upon imagining the sonorous aspect of the city in relation to the bell. Many of the dimensions indicated, both known and unknown, are just awakened to the study of what a sound space designer, as Llorenç Barber, comes to tell us, from a discipline apparently contacted, but often parallel to the architecture. Taking the bell concerts held so far as actual implementation of the instrumental condition of over two hundred cities around the world, the study analyzes the findings, successes and failures, obtained over the last twenty years of experience, as explicit results of a sound work in the city, tested, verified and refined, from which to extract specific indications that can be applied in the design of urban space. By triangular analyzing of defined vertices: sender-bell, half-city, receptor-citizen; the research addresses issues relating to the production and reception of sound phenomenon generated by the bell in the city. In relation to production, part of the work is devoted to the study of observed acoustic effects, ordered gradual scale which produces a distribution of sound capable of design: the glass of the bell, the bell room, the bell tower and the body of the building, the city and territory. By way of sounding boards and read as if they were Russian dolls, one inside the other, the show spaces identified specific sound qualities, defined both for their geometric, formal, constructive use, such as those for hosting the subsequent boxes. In order to clarify the influence of such issues in the sound aspect of the city, we propose an ordered pattern of connection and disconnection of scales, using a purely parametric technique created on purpose, along with more traditional methodological variables. At the same time, and trying to clarify how, when set in vibration, the city is apprehended, enjoyed and remembered for the citizen-listener, another part of the work is devoted to the study of aspects of aural reception in shared ambulation. In this case the research aims to claim more subversive than other dimensions, but beyond the usual ways in which an architect works, the experience reveals intensely plurifocal multiplying effects to consider: functional effects and significant recognition and integration belonging to a body of territorial and social historical and geographical coordinates of new meaning and perceptual effects of immersion, ubiquity, timeliness or instability; aesthetic effects of recall, interpretation and recreation of symbolic poetic; and even political effects, revealing a continuous urban space regeneration site for the exhibition in its double meaning, for display and danger, or as a citizen sense container. To sharpen the relevance of what was obtained in each of the dimensions mentioned, the work is divided into three incremental approaches: the general corpus of the concerts held so far, the concerts in Spain, the three concerts for Madrid: Magna Mater (1991), Festi Clamores (2000) and Aurea Catena (2007). While the proposed model comes in the light of the bells concert Llorenç Barber, the scale of a whole city and individual compositional intent, it is understood that it would be useful for the orderly use of any professional interested in the sound aspect of the city, an aspect sparsely attended, incidentally, from the architectural discipline.

Criterios de calidad del servicio prestado en el ámbito de la línea de atraque de las terminales portuarias de contenedores

Esta Tesis Doctoral evalúa empíricamente la calidad del servicio en la línea de atraque de las terminales portuarias de contenedores. La metodología propuesta utiliza indicadores de calidad y se basa en el concepto de la segmentación de servicio. Para ello se desarrolla la teoría del Control Estadístico de Procesos (CEP) y se utilizan los gráficos de control para clasificar el servicio en las terminales de contenedores. El propósito de la Tesis es proporcionar una metodología basada en el Control Estadístico de Procesos (CEP) para evaluar la calidad del servicio y detectar las escalas de un servicio regular de línea que se encuentran fuera de control. Por tanto, la metodología se puede utilizar para detectar eventos que son indicativos de cambio real del proceso en la línea de atraque. Esta detección puede ser compleja pues las características de los procesos en terminales de contenedores son variables. La metodología proporciona mediante los gráficos de control criterios estadísticamente objetivos de cambio. Cuando el cambio es detectado y considerado bueno sus causas deben ser identificadas y posiblemente convertirse en la nueva forma de trabajar, cuando el cambio es negativo, entonces sus causas deberían ser identificadas y eliminadas. La Tesis Doctoral está organizado de la siguiente manera: La primera parte es la introducción, e incluye los capítulos 1 al 4, la segunda parte presenta el Estado del Arte (capítulo 5) y algunos de los estudios que han inspirado esta investigación, la tercera parte se centra en la metodología utilizada (capítulo 6) y su aplicación sobre un caso de estudio (capítulo 7). Finalmente, en la cuarta parte se presentan las conclusiones y se proponen algunas de las nuevas líneas de investigación que quedan abiertas (capítulo 8). This Thesis empirically evaluates the quality of service in the berthing face of container terminals. The methodology proposed is focused on quality of service indicators and is based on the concept of service segmentation. The Statistical Process Control (SPC) theory and the control charts are used to classify container terminal service. The aim of this Thesis is to provide a methodology based on Statistical Process Control that can evaluate the quality of service and also can detect scales of shipping liner service that are out of control. Therefore, the methodology can be used to detect events that are indicative of real change in the berthing process of container vessels. The methodology proposed allows simple detection of events that are indicative of actual process change in container terminals. This detection is complex because the characteristics of the processes are variable in the container terminals; the control chart provides statistically objective criteria of change. When change is detected and considered good its cause should be identified and possibly become the new way of working, where the change is bad then its cause should be identified and eliminated. This Thesis is organized as follows: The first part is the introduction (includes Chapters 1 to 4), the second part presents the State of the Art (Chapter 5) and some of the studies that have inspired this research. The third part focuses on the methodology used (Chapter 6) and its application to a case study (Chapter 7). Finally, Part 4 presents the conclusions and suggests future research (Chapter 8).

Valorización de subproductos agrícolas y forestales como sustratos de cultivo en el estado de Oaxaca (México)

El presente trabajo aborda el aprovechamiento de algunos subproductos agrícolas (bagazo de maguey y fibra de coco) y forestales (corteza de pino) en el Estado de Oaxaca (Sur de México). El objetivo principal se centra en localizar, cuantificar y caracterizar estos con vistas a su aplicación como sustratos o componentes de sustratos en cultivos ornamentales, forestales y hortícolas, y a su uso como enmiendas en cultivos tipo. Así mismo se persigue reducir el uso de la turba y la tierra de monte como sustratos mayoritarios en la actualidad. Para la localización de los subproductos se utilizaron los datos de los registros parcelarios de los productores de coco para la obtención de copra (generadores de fibra de coco) de la región costa y de los productores de mezcal (generadores del residuo de bagazo de maguey) de la región valles centrales, así como las ubicaciones de los aserraderos forestales en el Estado de Oaxaca. Se emplea un Sistema de Información Geográfica (SIG) con una cartografía digitalizada de los elementos del medio (clima, geología y suelo), de los cultivos generadores (bagazo de maguey, fibra de coco y corteza de pino), de la agricultura protegida como receptora (tomate) y de la agricultura extensiva con cultivos receptores de enmienda (café, hule, limón, mango, palma de coco y maguey). La producción anual de los residuos se cartografía y cuantifica con los siguientes resultados: bagazo de maguey 624.000 t, fibra de coco 86.000 m3 y 72.000 t de corteza de pino. Mediante el estudio de las características de los suelos de los cultivos receptores y de los requerimientos de materia orgánica de cada cultivo se calcularon las necesidades totales de materia orgánica para cada suelo. Los resultados de las cantidades globales para cada cultivo en todo el Estado muestran una necesidad total de 3.112.000 t de materia orgánica como enmienda. Con los datos obtenidos y a través de un algoritmo matemático se realiza una propuesta de localización de dos plantas de compostaje (de bagazo de maguey y fibra de coco) y cuatro plantas de compostaje de corteza de pino. Con el fin de conocer los subproductos a valorizar como sustrato o componente de sustrato se caracteriza su composición física‐química, siguiendo Normas UNE‐EN, y se analizan mediante Resonancia Magnética Nuclear (RMN). Para el acondicionamiento de bagazo de maguey y la corteza de pino se realizaron ensayos de compostaje. Al final de 241 días la temperatura y la humedad de ambos procesos se encontraban en los rangos recomendados, indicando que los materiales estaban estabilizados y con calidad para ser utilizados como sustrato o componente de sustrato. Para la fibra de coco se realizó el proceso de molienda en seco de conchas de coco provenientes de la comunidad de Río Grande Oaxaca (Principal zona productora de copra en Oaxaca). Posteriormente se emplean los materiales obtenidos como componentes para sustratos de cultivo. Se estudia el compost de bagazo de maguey y siete mezclas; el compost de corteza de pino y ocho mezclas y la fibra de coco con tres mezclas. Estos sustratos alternativos permiten obtener mezclas y reducir el uso de la tierra de monte, turba, arcilla expandida y vermiculita, siendo por tanto una alternativa sostenible para la producción en invernadero. Se elaboraron mezclas especificas para el cultivo de Lilium hibrido asiático y oriental (siete mezclas), sustratos eco‐compatibles para cultivo de tomate (nueve mezclas), para la producción de planta forestal (siete mezclas) y para la producción de plántula hortícola (ocho mezclas). Como resultados más destacados del bagazo de maguey, corteza de pino y las mezclas obtenidas se resume lo siguiente: el bagazo de maguey, con volúmenes crecientes de turba (20, 30, 50 y 60 %) y la corteza de pino, con volúmenes de turba 40 y 60%, presentan valores muy recomendados de porosidad, capacidad de aireación, capacidad de retención de humedad y equilibrio agua‐aire. Para la fibra de coco, la procedente de Río Grande presenta mejor valoración que la muestra comercial de fibra de coco de Morelos. Por último se llevó a cabo la evaluación agronómica de los sustratos‐mezclas, realizando cinco experimentos por separado, estudiando el desarrollo vegetal de cultivos tipo, que se concretan en los siguientes ensayos: 1. Producción de Lilium asiático y oriental en cama para flor de corte; 2. Producción de Lilium oriental en contenedor para flor de corte; 3. Producción de plántula forestal (Pinus greggii E y Pinus oaxacana M); 4. Producción de tomate (Solanum lycopersicum L) y 5. Producción de plántula de tomate en semillero (Solanum lycopersicum L). En relación a la producción de Lilium hibrido asiático en cama los sustratos corteza de pino (CPTU 80:20 v/v), corteza de pino + sustrato comercial (CPSC 80:20 v/v) y corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV2 30:40:15:15 v/v) presentan los mejores resultados. Dichos sustratos también presentan adecuados resultados para Lilium hibrido oriental con excepción de la corteza de pino + turba (CPTU 80:20 v/v). En la producción de Lilium hibrido oriental en contenedor para flor de corte, además de los sustratos de CPSC y CPTAEV2, la mezcla de corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV 70:20:5:5 v/v) manifestó una respuesta favorable. En el ensayo de producción de plántulas de Pinus greggii E y Pinus oaxacana Mirov, las mezclas con corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV2 30:40:15:15 v/v) y bagazo de maguey turba+arcilla expandida+vermiculita (BMTAEV2 30:60:5:5 v/v) son una alternativa que permite disminuir el empleo de turba, arcilla expandida y vermiculita, en comparación con el sustrato testigo de turba+arcilla expandida+vermiculita (TAEV 60:30:10 v/v). En la producción de tomate (Solanum lycopersicum L) frente a la utilización actual del serrín sin compostar (SSC), las mezclas alternativas de bagazo de maguey+turba (BMT 70:30 v/v), fibra de coco de Río Grande (FCRG 100v/v) y corteza de pino+turba (CPT 70:30 v/v), presentaron los mejores resultados en rendimientos. Así mismo, en la producción de plántulas de tomate las dos mezclas alternativas de bagazo de maguey+turba+ arcilla expandida+vermiculita (BMTAEV5 50:30:10:10 v/v) y (BMTAEV6 40:40:10:10 v/v) presentaron mejores resultados que los obtenidos en la mezcla comercial (Sunshine 3), mayoritariamente utilizada en México en la producción de plántula de tomate y hortícola. ABSTRACT This paper addresses the use of some agricultural products (maguey bagasse and coconut fiber) and forestry (pine bark) in the State of Oaxaca (southern Mexico). The principal purpose is to locate, quantify and characterize these with the idea of applying them as substrates or substrate components in ornamental crops, forestry, horticultural, and their use as crop amendments. On the other hand, the reduction of peat and forest soil as main substrates is pursued. For the location of the products, registry parcel data from copra producers (coconut fiber generators) of the coastal region and mescal producers (maguey bagasse residue generators) of the central valleys region, as well as the locations of forest mills in the State of Oaxaca. A Geographic Information System (GIS) with digital mapping of environmental factors (climate, geology and soil), crop generators of residues (maguey bagasse, coconut and pine bark) receptors of amendments such as protected agriculture (tomato) and extensive agriculture crops (coffee, rubber, lemon, mango, coconut and agave). The annual production of waste is mapped and quantified with the following results: 624,000t maguey bagasse, coconut fiber 72,000 m3 and 86,000 t of pine bark. Through the study of receiving crops soils properties of and organic matter requirements of each crop, total needs of organic matter for each soil were estimated. The results of the total quantities for each crop across the state show a total of 3,112,000 t of organic matter needed as amendment. Using that data and a mathematical algorithm, the location of two composting plants (agave bagasse and coconut fiber) and four composting plants pine bark was proposed. In order to know the by‐products that were going to be used as substrates or substrate components, their physical‐chemical composition was analyzed following UNE‐EN technics. Furthermore they were analyzed by Nuclear Magnetic Resonance (NMR). For conditioning of maguey bagasse and pine bark, composting essays were conducted. At the end of 241 days the temperature and humidity of both processes were at the recommended ranges, indicating that the materials were stabilized and had reached the quality to be used as a substrate or substrate component. Coconut shells from the community of Rio Grande Oaxaca (Main copra producing area in Oaxaca) were put through a process of dry milling. Subsequently, the obtained materials were used as components for growing media. We studied the maguey bagasse compost and seven mixtures; the pine bark compost and eight blends and coconut fiber with three mixtures. These alternative substrates allow obtaining mixtures and reduce the use of forest soil, peat, vermiculite and expanded clay, making it a sustainable alternative for greenhouse production. Specific mixtures were prepared for growing Lillium, Asian and eastern hybrids (seven blends), eco‐compatible substrates for tomato (nine mixtures), for producing forest plant (seven mixtures) and for the production of horticultural seedlings (eight mixtures). Results from maguey bagasse, pine bark and mixtures obtained are summarized as follows: the maguey bagasse, with increasing volumes of peat (20, 30, 50 and 60%) and pine bark mixed with 40 and 60% peat by volume, have very recommended values of porosity, aeration capacity, water retention capacity and water‐air balance. Coconut fiber from Rio Grande had better quality than commercial coconut fiber from Morelos. Finally the agronomic evaluation of substrates‐mixtures was carried out conducting five experiments separately: 1. Production of Asiatic and Eastern Lilium in bed for cut flower, 2. Production of oriental Lillium in container for cut flower, 3.Production of forest seedlings (Pinus greggii E and Pinus oaxacana M), 4. Production of tomato (Solanum lycopersicum L) and 5. Tomato seedling production in seedbed (Solanum lycopersicum L). In relation to the production of hybrid Asian Lilium in bed, pine bark substrates (CPTU 80:20 v/v), pine bark + commercial substrate (CPSC 80:20 v/v) and pine bark + peat + expanded clay + vermiculite (CPTAEV2 30:40:15:15 v/v) showed the best results. Such substrates also have adequate results for Lilium Oriental hybrid except pine bark + peat (CPTU 80:20 v / v). In the production of Lilium oriental hybrid container for cut flower, besides the CPSC and CPTAEV2 substrates, the mixture of pine bark + peat + vermiculite expanded clay (CPTAEV 70:20:5:5 v / v) showed a favorable response. In the production of Pinus greggii E and Pinus oaxacana Mirov seedlings trial, mixtures with pine bark + peat + expanded clay + vermiculite (CPTAEV2 30:40:15:15 v/v) and maguey bagasse+ peat+ expanded clay + vermiculite (BMTAEV2 30:60:5:5 v / v) are an alternative which allows reducing the use of peat, vermiculite and expanded clay in comparison with the control substrate made of peat + expanded clay+ vermiculite (60:30 TAEV: 10 v/v). In the production of tomato (Solanum lycopersicum L), alternative mixes of maguey bagasse + peat (BMT 70:30 v/v), coconut fiber from Rio Grande (FCRG 100 v / v) and pine bark + peat (CPT 70:30 v / v) showed the best results in yields versus the current use of sawdust without compost (SSC). Likewise, in the production of tomato seedlings of the two alternative mixtures maguey bagasse + peat expanded clay + vermiculite (BMTAEV5 50:30:10:10 v/v) and (BMTAEV6 40:40:10:10 v/v) had better results than those obtained in the commercial mixture (Sunshine 3), mainly used in Mexico in tomato seedling production and horticulture.

Do charges to freight trucks and trains in the European Union reflect their social marginal costs? Application to the case of Spain

In the last few years, the European Union (EU) has become greatly concerned about the environmental costs of road transport in Europe as a result of the constant growth in the market share of trucks and the steady decline in the market share of railroads. In order to reverse this trend, the EU is promoting the implementation of additional charges for heavy goods vehicles (HGV) on the trunk roads of the EU countries. However, the EU policy is being criticised because it does not address the implementation of charges to internalise the external costs produced by automobiles and other transport modes such as railroad. In this paper, we first describe the evolution of the HGV charging policy in the EU, and then assess its practical implementation across different European countries. Second, and of greater significance, by using the case study of Spain, we evaluate to what extent the current fees on trucks and trains reflect their social marginal costs, and consequently lead to an allocative-efficient outcome. We found that for the average case in Spain the truck industry meets more of the marginal social cost produced by it than does the freight railroad industry. The reason for this lies in the large sums of money paid by truck companies in fuel taxes, and the subsidies that continue to be granted by the government to the railroads.

Metodología para maximizar la rentabilidad de una terminal marítima de contenedores a través de la optimización de su grado de automatización

Son generalmente aceptadas las tendencias actuales de maximización de la automatización para la adaptación de las terminales marítimas de contenedores a las cada vez mayores exigencias competitivas del negocio de transporte de contenedores. En esta investigación, se somete a consideración dichas tendencias a través de un análisis que tenga en cuenta la realidad global de la terminal pero también su propia realidad local que le permita aprovechar sus fortalezas y minimizar sus debilidades en un mercado continuamente en crecimiento y cambio. Para lo cual se ha desarrollado un modelo de análisis en el que se tengan en cuenta los parámetros técnicos, operativos, económicos y financieros que influyen en el diseño de una terminal marítima de contenedores, desde su concepción como ente dependiente para generar negocio, todos ellos dentro de un perímetro definido por el mercado del tráfico de contenedores así como las limitaciones físicas introducidas por la propia terminal. Para la obtención de dicho modelo ha sido necesario llevar a cabo un proceso de estudio del contexto actual del tráfico de contenedores y su relación con el diseño de las terminales marítimas, así como de las metodologías propuestas hasta ahora por los diferentes autores para abordar el proceso de dimensionamiento y diseño de la terminal. Una vez definido el modelo que ha de servir de base para el diseño de una terminal marítima de contenedores desde un planteamiento multicriterio, se analiza la influencia de las diversas variables explicativas de dicho modelo y se cuantifica su impacto en los resultados económicos, financieros y operativos de la terminal. Un paso siguiente consiste en definir un modelo simplificado que vincule la rentabilidad de una concesión de terminal con el tráfico esperado en función del grado de automatización y del tipo de terminal. Esta investigación es el fruto del objetivo ambicioso de aportar una metodología que defina la opción óptima de diseño de una terminal marítima de contenedores apoyada en los pilares de la optimización del grado de automatización y de la maximización de la rentabilidad del negocio que en ella se desarrolla. It is generally accepted current trends in automation to maximize the adaptation of maritime container terminals to the growing competitive demands of the business of container shipping. In this research, is submitted to these trends through an analysis taking into account the global reality of the terminal but also their own local reality it could exploit its strengths and minimize their weaknesses in a market continuously growing and changing. For which we have developed a model analysis that takes into account the technical, operational, financial and economic influence in the design of a container shipping terminal, from its conception as being dependent to generate business, all within a perimeter defined by the market of container traffic and the physical constraints introduced by the terminal. To obtain this model has been necessary to conduct a study process in the current context of container traffic and its relation to the design of marine terminals, as well as the methodologies proposed so far by different authors to address the process sizing and design of the terminal. Having defined the model that will serve as the basis for the design for a container shipping terminal from a multi-criteria approach, we analyze the influence of various explanatory variables of the model and quantify their impact on economic performance, financial and operational of the terminal. A next step is to define a simplified model that links the profitability of a terminal concession with traffic expected on the basis of the degree of automation and the kind of terminal. This research is the result of the ambitious target of providing a methodology to define the optimal choice of designing a container shipping terminal on the pillars of automation optimizing and maximizing the profitability of the business that it develops.

News in engineering education in Spain effective from 2010 in presence of external changes and mixed crisis, looking mostly to agro and civil engineers.

The engineering careers models were diverse in Europe, and are adopting now in Spain the Bolonia process for European Universities. Separated from older Universities, that are in part technically active, Civil Engineering (Caminos, Canales y Puertos) started at end of 18th century in Spain adopting the French models of Upper Schools for state civil servants with exam at entry. After 1800 intense wars, to conserve forest regions Ingenieros de Montes appeared as Upper School, and in 1855 also the Ingenieros Agrónomos to push up related techniques and practices. Other Engineers appeared as Upper Schools but more towards private factories. These ES got all adapted Lower Schools of Ingeniero Tecnico. Recently both grew much in number and evolved, linked also to recognized Professions. Spanish society, into European Community, evolved across year 2000, in part highly well, but with severe discordances, that caused severe youth unemployment with 2008-2011 crisis. With Bolonia process high formal changes step in from 2010-11, accepted with intense adaptation. The Lower Schools are changing towards the Upper Schools, and both that have shifted since 2010-11 various 4-years careers (Grado), some included into the precedent Professions, and diverse Masters. Acceptation of them to get students has started relatively well, and will evolve, and acceptation of new grades for employment in Spain, Europe or outside will be essential. Each Grado has now quite rigid curricula and programs, MOODLE was introduced to connect pupils, some specific uses of Personal Computers are taught in each subject. Escuela de Agronomos centre, reorganized with its old name in its precedent buildings at entrance of Campus Moncloa, offers Grados of Agronomic Engineering and Science for various public and private activities for agriculture, Alimentary Engineering for alimentary activities and control, Agro-Environmental Engineering more related to environment activities, and in part Biotechnology also in laboratories in Campus Monte-Gancedo for Biotechnology of Plants and Computational Biotechnology. Curricula include Basics, Engineering, Practices, Visits, English, ?project of end of career?, Stays. Some masters will conduce to specific professional diploma, list includes now Agro-Engineering, Agro-Forestal Biotechnology, Agro and Natural Resources Economy, Complex Physical Systems, Gardening and Landscaping, Rural Genie, Phytogenetic Resources, Plant Genetic Resources, Environmental Technology for Sustainable Agriculture, Technology for Human Development and Cooperation.

Diseño y aplicación de una metodología prospectiva para la determinación de los condicionantes futuros del crecimiento de los grandes buques portacontenedores

Durante las últimas décadas se observa una tendencia sostenida al crecimiento en las dimensiones de los grandes buques portacontenedores, que produce, que las infraestructuras portuarias y otras destinadas al tráfico de contenedores deban adaptarse para poder brindar los servicios correspondientes y mantenerse competitivas con otras para no perder el mercado. Esta situación implica importantes inversiones y modificaciones en los sistemas de transporte de contenedores por el gran volumen de carga que se debe mover en un corto periodo de tiempo, lo que genera la necesidad de tomar previsiones relacionadas con la probable evolución a futuro de las dimensiones que alcanzarán los grandes buques portacontenedores. En relación a los aspectos citados surge la inquietud de determinar los condicionantes futuros del crecimiento de los grandes buques portacontenedores, con una visión totalizadora de todos los factores que incidirán en los próximos años, ya sea como un freno o un impulso a la tendencia que se verifica en el pasado y en el presente. En consideración a que el tema a tratar y resolver se encuentra en el futuro, con un horizonte de predicción de veinte años, se diseña y se aplica una metodología prospectiva, que permite alcanzar conclusiones con mayor grado de objetividad sobre probables escenarios futuros. La metodología prospectiva diseñada, conjuga distintas herramientas metodológicas, cualitativas, semi-cuantitativas y cuantitativas que se validan entre sí. Sobre la base del pasado y el presente, las herramientas cuantitativas permiten encontrar relaciones entre variables y hacer proyecciones, sin embargo, estas metodologías pierden validez más allá de los tres a cuatro años, por los vertiginosos y dinámicos cambios que se producen actualmente, en las áreas política, social y económica. Las metodologías semi-cuantitativas y cualitativas, empleadas en forma conjunta e integradas, permiten el análisis de circunstancias del pasado y del presente, obteniendo resultados cuantitativos que se pueden proyectar hacia un futuro cercano, los que integrados en estudios cualitativos proporcionan resultados a largo plazo, facilitando considerar variables cualitativas como la creciente preocupación por la preservación del medio ambiente y la piratería. La presente tesis, tiene como objetivo principal “identificar los condicionantes futuros del crecimiento de los grandes buques portacontenedores y determinar sus escenarios”. Para lo cual, la misma se estructura en fases consecutivas y que se retroalimentan continuamente. Las tres primeras fases son un enfoque sobre el pasado y el presente, que establece el problema a resolver. Se estudian los antecedentes y el estado del conocimiento en relación a los factores y circunstancias que motivaron y facilitaron la tendencia al crecimiento de los grandes buques. También se estudia el estado del conocimiento de las metodologías para predecir el futuro y se diseña de una metodología prospectiva. La cuarta fase, denominada Resultados, se desarrolla en distintas etapas, fundamentadas en las fases anteriores, con el fin de resolver el problema dando respuestas a las preguntas que se formularon para alcanzar el objetivo fijado. En el proceso de esta fase, con el objeto de predecir probables futuros, se aplica la metodología prospectiva diseñada, que contempla el análisis del pasado y el presente, que determina los factores cuya influencia provocó el crecimiento en dimensiones de los grandes buques hasta la actualidad, y que constituye la base para emplear los métodos prospectivos que permiten determinar qué factores condicionarán en el futuro la evolución de los grandes buques. El probable escenario futuro formado por los factores determinados por el criterio experto, es validado mediante un modelo cuantitativo dinámico, que además de obtener el probable escenario futuro basado en las tendencias de comportamiento hasta el presente de los factores determinantes considerados, permite estudiar distintos probables escenarios futuros en función de considerar un cambio en la tendencia futura de los factores determinantes. El análisis del pasado indica que la tendencia al crecimiento de los grandes buques portacontenedores hasta el presente, se ha motivado por un crecimiento económico mundial que se tradujo en un aumento del comercio internacional, particularmente entre los países de Asia, con Europa y Estados Unidos. Esta tendencia se ha visto favorecida por el factor globalización y la acelerada evolución tecnológica que ha permitido superar los obstáculos que se presentaron. Es de destacar que aún en periodos de crisis económicas, con pronósticos de contracciones en el comercio, en los últimos años continuó la tendencia al crecimiento en dimensiones, en busca de una economía de escala para el transporte marítimo de contenedores, en las rutas transoceánicas. La investigación de la evolución de los grandes buques portacontenedores en el futuro, se efectúa mediante el empleo de una metodología prospectiva en la que el criterio experto se valida con un método cuantitativo dinámico, y además se fundamenta en una solida base pre-prospectiva. La metodología diseñada permite evaluar con un alto grado de objetividad cuales serán los condicionantes que incidirán en el crecimiento en tamaño de los grandes buques portacontenedores en el escenario con mayor probabilidad de acontecer en los próximos veinte años (2032), y también en otros escenarios que podrían presentarse en el caso de que los factores modifiquen su tendencia o bien se produzcan hechos aleatorios. El resultado se sintetiza en que la tendencia al crecimiento de los grandes buques portacontenedores en los próximos 20 años se verá condicionada por factores en relación a los conceptos de oferta (los que facilitan u obstaculizan la tendencia), demanda (los que motivan o impulsan la tendencia) y factores externos (los que desestabilizan el equilibrio entre oferta y demanda). La tendencia al crecimiento de los grandes buques portacontenedores se verá obstaculizada / limitada principalmente por factores relacionados a las infraestructuras, resultando los pasos y/o canales vinculados a las rutas marítimas, los limitantes futuros al crecimiento en dimensiones de los grandes buques portacontenedores; y la interacción buque / infraestructura (grúas) un factor que tenderá a obstaculizar esta tendencia de los grandes portacontenedores. El desarrollo económico mundial que estimula el comercio internacional y los factores precio del petróleo y condicionantes medioambientales impulsarán la tendencia al crecimiento de los grandes buques portacontenedores. Recent years have seen a sustained tendency towards the growth in the dimensions of large container ships. This has meant that port and other infrastructure used for container traffic has had to be adapted in order to provide the required services and to maintain a competitive position, so as not to lose market share. This situation implies the need for major investments in modifications to the container transport system, on account of the large volume of traffic to be handled in a short period of time. This in turn has generated a need to make provision for the probable future evolution of the ultimate dimensions that will be reached by large container ships. Such considerations give rise to the question of what are the future determinants for the growth of large container ships, requiring an overall vision of all the factors that will apply in future years, whether as a brake on or an incentive to the growth tendency which has been seen in the past and present In view of the fact that the theme to be dealt with and resolved relates to the future, with a forecasting horizon of some 20 years, a foresight methodology has been designed and applied so as to enable conclusions about probable future scenarios to be reached with a greater degree of objectivity. The designed methodology contains different methodological tools, both qualitative, semi-quantitative and quantitative, which are internally consistent. On the basis of past and present observations, the quantitative elements enable relationships to be established and forecasts to be made. Nevertheless such an approach loses validity more than three or four years into the future, on account of the very rapid and dynamic changes which may be seen at present in political, social and economic spheres. The semi-quantitative and qualitative methodologies are used coherently together and allow the analysis of past and present conditions, thus obtaining quantitative results which for short-term projections, which when integrated with the qualitative studies provide results for the long-term, facilitating the consideration of qualitative variables such as the increasing importance of environmental protection and the impact of piracy. The principal objective of the present thesis is "to identify the future conditions affecting the growth of large container ships and to determine possible scenarios". The thesis is structured in consecutive and related phases. The first three phases focus on the past and present in order to determine the problem to be resolved. The background is studied in order to establish the state of knowledge about the factors and circumstances which have motivated and facilitated the growth tendency for large container ships and the methodologies that have been used. In this way a specific foresight methodology is designed. The fourth phase, Results, is developed in distinct stages based on the previous phases, so as to resolve the problem posed and responding to the questions that arise. In this way the determined objective is reached. The fourth phase sees the application of the methodology that has been designed in order to predict posible futures. This includes analysis of the past and present factors which have caused the growth in the dimensions of large container ships up to the present. These provide the basis on which to apply the foresight methods which enable the future factors which will condition the development of such large container ships. The probable future scenarios are made up of the factors identified by expert judgement (using the Delphi technique) and validated by means of a dynamic quantitative model. This model both identifies the probable future scenarios based on past and present factors and enables the different future scenarios to be analysed as a function of future changes in the conditioning factors. Analysis of the past shows that the growth tendency up to the present for large container ships has been motivated by the growth of the world economy and the consequent increased international trade, especially between the countries of Asia with Europe and the United States. This tendency has been favoured by the trend towards globalization and by the rapid technical evolution in ship design, which has allowed the obstacles encountered to be overcome. It should be noted that even in periods of economic crisis, with an expectation for reduced trade, as experienced in recent years, the tendency towards increased ship dimensions has continued in search of economies of scale for the maritime transport of containers on transoceanic routes. The present investigation of the future evolution of large container ships has been done using a foresight methodology in which the expert judgement is validated by a dynamic quantitative methodology, founded on a firm pre-foresight analysis. The methodology that has been designed permits the evaluation, with a high degree of objectivity, of the future factors that will affect the growth of large container ships for the most probable scenario expected in the next 20 years (up to 2032). The evaluation applies also to other scenarios which may arise, in the event that their component factors are modified or indeed in the light of random events. In summary, the conclusión is that the tendency for growth in large container ships in the future 20 years will be determined by: factors related to supply, which slow or halt the tendency; factors related to demand, which encourage the tendency and finally, external factors which interrupt the equilibrium between supply and demand. The tendency for increasing growth in large container ships will be limited or even halted by factors related to infrastructure, including the natural and man-made straits and canals used by maritime transport. In addition the infrastructure required to serve such vessels both in port (including cranes and other equipment) and related transport, will tend to slow the growth tendency. The factors which will continue to encourage the tendency towards the growth of large container ships include world economic development, which stimulates international trade, and an increasing emphasis on environmental aspects.