The use of arc-erosion as a patterning technique for transparent conductive materials

Within the framework of cost-effective patterning processes a novel technique that saves photolithographic processing steps, easily scalable to wide area production, is proposed. It consists of a tip-probe, which is biased with respect to a conductive substrate and slides on it, keeping contact with the material. The sliding tip leaves an insulating path (which currently is as narrow as 30 μm) across the material, which enables the drawing of tracks and pads electrically insulated from the surroundings. This ablation method, called arc-erosion, requires an experimental set up that had to be customized for this purpose and is described. Upon instrumental monitoring, a brief proposal of the physics below this process is also presented. As a result an optimal control of the patterning process has been acquired. The system has been used on different substrates, including indium tin oxide either on glass or on polyethylene terephtalate, as well as alloys like Au/Cr, and Al. The influence of conditions such as tip speed and applied voltage is discussed

On the harmonic analysis of cup anemometer rotation speed: A principle to monitor performance and maintenance status of rotating meteorological sensors

The calibration results of one anemometer equipped with several rotors, varying their size, were analyzed. In each case, the 30-pulses pert turn output signal of the anemometer was studied using Fourier series decomposition and correlated with the anemometer factor (i.e., the anemometer transfer function). Also, a 3-cup analytical model was correlated to the data resulting from the wind tunnel measurements. Results indicate good correlation between the post-processed output signal and the working condition of the cup anemometer. This correlation was also reflected in the results from the proposed analytical model. With the present work the possibility of remotely checking cup anemometer status, indicating the presence of anomalies and, therefore, a decrease on the wind sensor reliability is revealed.

COMSOL Multyphisics Super Resolution Analysis of a Spherical Geodesic Waveguide Suitable for Manufacturing

Recently it has been proved theoretically (Miñano et al, 2011) that the super-resolution up to ?/500 can be achieved using an ideal metallic Spherical Geodesic Waveguide (SGW). This SGW is a theoretical design, in which the conductive walls are considered to be lossless conductors with zero thickness. In this paper, we study some key parameters that might influence the super resolution properties reported in (Miñano et al, 2011), such as losses, metal type, the thickness of conductive walls and the deformation from perfect sphere. We implement a realistic SGW in COMSOL multiphysics and analyze its super-resolution properties. The realistic model is designed in accordance with the manufacturing requirements and technological limitations.

Short, high current electrodynamic tether

An electrodynamic tether experiment, to be carried out in the Russian spacecraft Almaz, is proposed. A 10 km tether would be deployed downwards; the lower 8 km would be nonconductive, the upper 2 km would be conductive, bare, and 2.2 mm in diameter, and would act as a thruster, with power supply at the top. This hybrid arrangement allows for other, onelectrodynamic experiments,reducing costs; it also limits the induced electromotive force, reducing the power to be handled. The current-voltage characteristic of contactors would be measured. With the anode switched off, the wire itself should collect a current over 5 A at day conditions, providing a thrust of 0.11 N at a 0.77 kW power.

Detección de patrones y anomalías espectrales del terreno mediante espectrometría de imagen de alta resolución : reconocimiento, optimización y evaluación multiescenario

El objeto de esta Tesis doctoral es el desarrollo de una metodologia para la deteccion automatica de anomalias a partir de datos hiperespectrales o espectrometria de imagen, y su cartografiado bajo diferentes condiciones tipologicas de superficie y terreno. La tecnologia hiperespectral o espectrometria de imagen ofrece la posibilidad potencial de caracterizar con precision el estado de los materiales que conforman las diversas superficies en base a su respuesta espectral. Este estado suele ser variable, mientras que las observaciones se producen en un numero limitado y para determinadas condiciones de iluminacion. Al aumentar el numero de bandas espectrales aumenta tambien el numero de muestras necesarias para definir espectralmente las clases en lo que se conoce como Maldicion de la Dimensionalidad o Efecto Hughes (Bellman, 1957), muestras habitualmente no disponibles y costosas de obtener, no hay mas que pensar en lo que ello implica en la Exploracion Planetaria. Bajo la definicion de anomalia en su sentido espectral como la respuesta significativamente diferente de un pixel de imagen respecto de su entorno, el objeto central abordado en la Tesis estriba primero en como reducir la dimensionalidad de la informacion en los datos hiperespectrales, discriminando la mas significativa para la deteccion de respuestas anomalas, y segundo, en establecer la relacion entre anomalias espectrales detectadas y lo que hemos denominado anomalias informacionales, es decir, anomalias que aportan algun tipo de informacion real de las superficies o materiales que las producen. En la deteccion de respuestas anomalas se asume un no conocimiento previo de los objetivos, de tal manera que los pixeles se separan automaticamente en funcion de su informacion espectral significativamente diferenciada respecto de un fondo que se estima, bien de manera global para toda la escena, bien localmente por segmentacion de la imagen. La metodologia desarrollada se ha centrado en la implicacion de la definicion estadistica del fondo espectral, proponiendo un nuevo enfoque que permite discriminar anomalias respecto fondos segmentados en diferentes grupos de longitudes de onda del espectro, explotando la potencialidad de separacion entre el espectro electromagnetico reflectivo y emisivo. Se ha estudiado la eficiencia de los principales algoritmos de deteccion de anomalias, contrastando los resultados del algoritmo RX (Reed and Xiaoli, 1990) adoptado como estandar por la comunidad cientifica, con el metodo UTD (Uniform Targets Detector), su variante RXD-UTD, metodos basados en subespacios SSRX (Subspace RX) y metodo basados en proyecciones de subespacios de imagen, como OSPRX (Orthogonal Subspace Projection RX) y PP (Projection Pursuit). Se ha desarrollado un nuevo metodo, evaluado y contrastado por los anteriores, que supone una variacion de PP y describe el fondo espectral mediante el analisis discriminante de bandas del espectro electromagnetico, separando las anomalias con el algortimo denominado Detector de Anomalias de Fondo Termico o DAFT aplicable a sensores que registran datos en el espectro emisivo. Se han evaluado los diferentes metodos de deteccion de anomalias en rangos del espectro electromagnetico del visible e infrarrojo cercano (Visible and Near Infrared-VNIR), infrarrojo de onda corta (Short Wavelenght Infrared-SWIR), infrarrojo medio (Meadle Infrared-MIR) e infrarrojo termico (Thermal Infrared-TIR). La respuesta de las superficies en las distintas longitudes de onda del espectro electromagnetico junto con su entorno, influyen en el tipo y frecuencia de las anomalias espectrales que puedan provocar. Es por ello que se han utilizado en la investigacion cubos de datos hiperepectrales procedentes de los sensores aeroportados cuya estrategia y diseno en la construccion espectrometrica de la imagen difiere. Se han evaluado conjuntos de datos de test de los sensores AHS (Airborne Hyperspectral System), HyMAP Imaging Spectrometer, CASI (Compact Airborne Spectrographic Imager), AVIRIS (Airborne Visible Infrared Imaging Spectrometer), HYDICE (Hyperspectral Digital Imagery Collection Experiment) y MASTER (MODIS/ASTER Simulator). Se han disenado experimentos sobre ambitos naturales, urbanos y semiurbanos de diferente complejidad. Se ha evaluado el comportamiento de los diferentes detectores de anomalias a traves de 23 tests correspondientes a 15 areas de estudio agrupados en 6 espacios o escenarios: Urbano - E1, Semiurbano/Industrial/Periferia Urbana - E2, Forestal - E3, Agricola - E4, Geologico/Volcanico - E5 y Otros Espacios Agua, Nubes y Sombras - E6. El tipo de sensores evaluados se caracteriza por registrar imagenes en un amplio rango de bandas, estrechas y contiguas, del espectro electromagnetico. La Tesis se ha centrado en el desarrollo de tecnicas que permiten separar y extraer automaticamente pixeles o grupos de pixeles cuya firma espectral difiere de manera discriminante de las que tiene alrededor, adoptando para ello como espacio muestral parte o el conjunto de las bandas espectrales en las que ha registrado radiancia el sensor hiperespectral. Un factor a tener en cuenta en la investigacion ha sido el propio instrumento de medida, es decir, la caracterizacion de los distintos subsistemas, sensores imagen y auxiliares, que intervienen en el proceso. Para poder emplear cuantitativamente los datos medidos ha sido necesario definir las relaciones espaciales y espectrales del sensor con la superficie observada y las potenciales anomalias y patrones objetivos de deteccion. Se ha analizado la repercusion que en la deteccion de anomalias tiene el tipo de sensor, tanto en su configuracion espectral como en las estrategias de diseno a la hora de registrar la radiacion prodecente de las superficies, siendo los dos tipos principales de sensores estudiados los barredores o escaneres de espejo giratorio (whiskbroom) y los barredores o escaneres de empuje (pushbroom). Se han definido distintos escenarios en la investigacion, lo que ha permitido abarcar una amplia variabilidad de entornos geomorfologicos y de tipos de coberturas, en ambientes mediterraneos, de latitudes medias y tropicales. En resumen, esta Tesis presenta una tecnica de deteccion de anomalias para datos hiperespectrales denominada DAFT en su variante de PP, basada en una reduccion de la dimensionalidad proyectando el fondo en un rango de longitudes de onda del espectro termico distinto de la proyeccion de las anomalias u objetivos sin firma espectral conocida. La metodologia propuesta ha sido probada con imagenes hiperespectrales reales de diferentes sensores y en diferentes escenarios o espacios, por lo tanto de diferente fondo espectral tambien, donde los resultados muestran los beneficios de la aproximacion en la deteccion de una gran variedad de objetos cuyas firmas espectrales tienen suficiente desviacion respecto del fondo. La tecnica resulta ser automatica en el sentido de que no hay necesidad de ajuste de parametros, dando resultados significativos en todos los casos. Incluso los objetos de tamano subpixel, que no pueden distinguirse a simple vista por el ojo humano en la imagen original, pueden ser detectados como anomalias. Ademas, se realiza una comparacion entre el enfoque propuesto, la popular tecnica RX y otros detectores tanto en su modalidad global como local. El metodo propuesto supera a los demas en determinados escenarios, demostrando su capacidad para reducir la proporcion de falsas alarmas. Los resultados del algoritmo automatico DAFT desarrollado, han demostrado la mejora en la definicion cualitativa de las anomalias espectrales que identifican a entidades diferentes en o bajo superficie, reemplazando para ello el modelo clasico de distribucion normal con un metodo robusto que contempla distintas alternativas desde el momento mismo de la adquisicion del dato hiperespectral. Para su consecucion ha sido necesario analizar la relacion entre parametros biofisicos, como la reflectancia y la emisividad de los materiales, y la distribucion espacial de entidades detectadas respecto de su entorno. Por ultimo, el algoritmo DAFT ha sido elegido como el mas adecuado para sensores que adquieren datos en el TIR, ya que presenta el mejor acuerdo con los datos de referencia, demostrando una gran eficacia computacional que facilita su implementacion en un sistema de cartografia que proyecte de forma automatica en un marco geografico de referencia las anomalias detectadas, lo que confirma un significativo avance hacia un sistema en lo que se denomina cartografia en tiempo real. The aim of this Thesis is to develop a specific methodology in order to be applied in automatic detection anomalies processes using hyperspectral data also called hyperspectral scenes, and to improve the classification processes. Several scenarios, areas and their relationship with surfaces and objects have been tested. The spectral characteristics of reflectance parameter and emissivity in the pattern recognition of urban materials in several hyperspectral scenes have also been tested. Spectral ranges of the visible-near infrared (VNIR), shortwave infrared (SWIR) and thermal infrared (TIR) from hyperspectral data cubes of AHS (Airborne Hyperspectral System), HyMAP Imaging Spectrometer, CASI (Compact Airborne Spectrographic Imager), AVIRIS (Airborne Visible Infrared Imaging Spectrometer), HYDICE (Hyperspectral Digital Imagery Collection Experiment) and MASTER (MODIS/ASTER Simulator) have been used in this research. It is assumed that there is not prior knowledge of the targets in anomaly detection. Thus, the pixels are automatically separated according to their spectral information, significantly differentiated with respect to a background, either globally for the full scene, or locally by the image segmentation. Several experiments on different scenarios have been designed, analyzing the behavior of the standard RX anomaly detector and different methods based on subspace, image projection and segmentation-based anomaly detection methods. Results and their consequences in unsupervised classification processes are discussed. Detection of spectral anomalies aims at extracting automatically pixels that show significant responses in relation of their surroundings. This Thesis deals with the unsupervised technique of target detection, also called anomaly detection. Since this technique assumes no prior knowledge about the target or the statistical characteristics of the data, the only available option is to look for objects that are differentiated from the background. Several methods have been developed in the last decades, allowing a better understanding of the relationships between the image dimensionality and the optimization of search procedures as well as the subpixel differentiation of the spectral mixture and its implications in anomalous responses. In other sense, image spectrometry has proven to be efficient in the characterization of materials, based on statistical methods using a specific reflection and absorption bands. Spectral configurations in the VNIR, SWIR and TIR have been successfully used for mapping materials in different urban scenarios. There has been an increasing interest in the use of high resolution data (both spatial and spectral) to detect small objects and to discriminate surfaces in areas with urban complexity. This has come to be known as target detection which can be either supervised or unsupervised. In supervised target detection, algorithms lean on prior knowledge, such as the spectral signature. The detection process for matching signatures is not straightforward due to the complications of converting data airborne sensor with material spectra in the ground. This could be further complicated by the large number of possible objects of interest, as well as uncertainty as to the reflectance or emissivity of these objects and surfaces. An important objective in this research is to establish relationships that allow linking spectral anomalies with what can be called informational anomalies and, therefore, identify information related to anomalous responses in some places rather than simply spotting differences from the background. The development in recent years of new hyperspectral sensors and techniques, widen the possibilities for applications in remote sensing of the Earth. Remote sensing systems measure and record electromagnetic disturbances that the surveyed objects induce in their surroundings, by means of different sensors mounted on airborne or space platforms. Map updating is important for management and decisions making people, because of the fast changes that usually happen in natural, urban and semi urban areas. It is necessary to optimize the methodology for obtaining the best from remote sensing techniques from hyperspectral data. The first problem with hyperspectral data is to reduce the dimensionality, keeping the maximum amount of information. Hyperspectral sensors augment considerably the amount of information, this allows us to obtain a better precision on the separation of material but at the same time it is necessary to calculate a bigger number of parameters, and the precision lowers with the increase in the number of bands. This is known as the Hughes effects (Bellman, 1957) . Hyperspectral imagery allows us to discriminate between a huge number of different materials however some land and urban covers are made up with similar material and respond similarly which produces confusion in the classification. The training and the algorithm used for mapping are also important for the final result and some properties of thermal spectrum for detecting land cover will be studied. In summary, this Thesis presents a new technique for anomaly detection in hyperspectral data called DAFT, as a PP's variant, based on dimensionality reduction by projecting anomalies or targets with unknown spectral signature to the background, in a range thermal spectrum wavelengths. The proposed methodology has been tested with hyperspectral images from different imaging spectrometers corresponding to several places or scenarios, therefore with different spectral background. The results show the benefits of the approach to the detection of a variety of targets whose spectral signatures have sufficient deviation in relation to the background. DAFT is an automated technique in the sense that there is not necessary to adjust parameters, providing significant results in all cases. Subpixel anomalies which cannot be distinguished by the human eye, on the original image, however can be detected as outliers due to the projection of the VNIR end members with a very strong thermal contrast. Furthermore, a comparison between the proposed approach and the well-known RX detector is performed at both modes, global and local. The proposed method outperforms the existents in particular scenarios, demonstrating its performance to reduce the probability of false alarms. The results of the automatic algorithm DAFT have demonstrated improvement in the qualitative definition of the spectral anomalies by replacing the classical model by the normal distribution with a robust method. For their achievement has been necessary to analyze the relationship between biophysical parameters such as reflectance and emissivity, and the spatial distribution of detected entities with respect to their environment, as for example some buried or semi-buried materials, or building covers of asbestos, cellular polycarbonate-PVC or metal composites. Finally, the DAFT method has been chosen as the most suitable for anomaly detection using imaging spectrometers that acquire them in the thermal infrared spectrum, since it presents the best results in comparison with the reference data, demonstrating great computational efficiency that facilitates its implementation in a mapping system towards, what is called, Real-Time Mapping.

Determinación de un modelo de geoide gravimétrico para Puerto Rico como sistema de referencia para las altitudes ortométricas

El geoide, definido como la superficie equipotencial que mejor se ajusta (en el sentido de los mínimos cuadrados) al nivel medio del mar en una determinada época, es la superficie que utilizamos como referencia para determinar las altitudes ortométricas. Si disponemos de una superficie equipotencial de referencia como dátum altimétrico preciso o geoide local, podemos entonces determinar las altitudes ortométricas de forma eficiente a partir de las altitudes elipsoidales proporcionadas por el Sistema Global de Navegación por Satélite (Global Navigation Satellite System, GNSS ). Como es sabido uno de los problemas no resueltos de la geodesia (quizás el más importante de los mismos en la actualidad) es la carencia de un dátum altimétrico global (Sjoberg, 2011) con las precisiones adecuadas. Al no existir un dátum altimétrico global que nos permita obtener los valores absolutos de la ondulación del geoide con la precisión requerida, es necesario emplear modelos geopotenciales como alternativa. Recientemente fue publicado el modelo EGM2008 en el que ha habido una notable mejoría de sus tres fuentes de datos, por lo que este modelo contiene coeficientes adicionales hasta el grado 2190 y orden 2159 y supone una sustancial mejora en la precisión (Pavlis et al., 2008). Cuando en una región determinada se dispone de valores de gravedad y Modelos Digitales del Terreno (MDT) de calidad, es posible obtener modelos de superficies geopotenciales más precisos y de mayor resolución que los modelos globales. Si bien es cierto que el Servicio Nacional Geodésico de los Estados Unidos de América (National Geodetic Survey, NGS) ha estado desarrollando modelos del geoide para la región de los Estados Unidos de América continentales y todos sus territorios desde la década de los noventa, también es cierto que las zonas de Puerto Rico y las Islas Vírgenes Estadounidenses han quedado un poco rezagadas al momento de poder aplicar y obtener resultados de mayor precisión con estos modelos regionales del geoide. En la actualidad, el modelo geopotencial regional vigente para la zona de Puerto Rico y las Islas Vírgenes Estadounidenses es el GEOID12A (Roman y Weston, 2012). Dada la necesidad y ante la incertidumbre de saber cuál sería el comportamiento de un modelo del geoide desarrollado única y exclusivamente con datos de gravedad locales, nos hemos dado a la tarea de desarrollar un modelo de geoide gravimétrico como sistema de referencia para las altitudes ortométricas. Para desarrollar un modelo del geoide gravimétrico en la isla de Puerto Rico, fue necesario implementar una metodología que nos permitiera analizar y validar los datos de gravedad terrestre existentes. Utilizando validación por altimetría con sistemas de información geográfica y validación matemática por colocación con el programa Gravsoft (Tscherning et al., 1994) en su modalidad en Python (Nielsen et al., 2012), fue posible validar 1673 datos de anomalías aire libre de un total de 1894 observaciones obtenidas de la base de datos del Bureau Gravimétrico Internacional (BGI). El aplicar estas metodologías nos permitió obtener una base de datos anomalías de la gravedad fiable la cual puede ser utilizada para una gran cantidad de aplicaciones en ciencia e ingeniería. Ante la poca densidad de datos de gravedad existentes, fue necesario emplear un método alternativo para densificar los valores de anomalías aire libre existentes. Empleando una metodología propuesta por Jekeli et al. (2009b) se procedió a determinar anomalías aire libre a partir de los datos de un MDT. Estas anomalías fueron ajustadas utilizando las anomalías aire libre validadas y tras aplicar un ajuste de mínimos cuadrados por zonas geográficas, fue posible obtener una malla de datos de anomalías aire libre uniforme a partir de un MDT. Tras realizar las correcciones topográficas, determinar el efecto indirecto de la topografía del terreno y la contribución del modelo geopotencial EGM2008, se obtuvo una malla de anomalías residuales. Estas anomalías residuales fueron utilizadas para determinar el geoide gravimétrico utilizando varias técnicas entre las que se encuentran la aproximación plana de la función de Stokes y las modificaciones al núcleo de Stokes, propuestas por Wong y Gore (1969), Vanicek y Kleusberg (1987) y Featherstone et al. (1998). Ya determinados los distintos modelos del geoide gravimétrico, fue necesario validar los mismos y para eso se utilizaron una serie de estaciones permanentes de la red de nivelación del Datum Vertical de Puerto Rico de 2002 (Puerto Rico Vertical Datum 2002, PRVD02 ), las cuales tenían publicados sus valores de altitud elipsoidal y elevación. Ante la ausencia de altitudes ortométricas en las estaciones permanentes de la red de nivelación, se utilizaron las elevaciones obtenidas a partir de nivelación de primer orden para determinar los valores de la ondulación del geoide geométrico (Roman et al., 2013). Tras establecer un total de 990 líneas base, se realizaron dos análisis para determinar la 'precisión' de los modelos del geoide. En el primer análisis, que consistió en analizar las diferencias entre los incrementos de la ondulación del geoide geométrico y los incrementos de la ondulación del geoide de los distintos modelos (modelos gravimétricos, EGM2008 y GEOID12A) en función de las distancias entre las estaciones de validación, se encontró que el modelo con la modificación del núcleo de Stokes propuesta por Wong y Gore presentó la mejor 'precisión' en un 91,1% de los tramos analizados. En un segundo análisis, en el que se consideraron las 990 líneas base, se determinaron las diferencias entre los incrementos de la ondulación del geoide geométrico y los incrementos de la ondulación del geoide de los distintos modelos (modelos gravimétricos, EGM2008 y GEOID12A), encontrando que el modelo que presenta la mayor 'precisión' también era el geoide con la modificación del núcleo de Stokes propuesta por Wong y Gore. En este análisis, el modelo del geoide gravimétrico de Wong y Gore presento una 'precisión' de 0,027 metros en comparación con la 'precisión' del modelo EGM2008 que fue de 0,031 metros mientras que la 'precisión' del modelo regional GEOID12A fue de 0,057 metros. Finalmente podemos decir que la metodología aquí presentada es una adecuada ya que fue posible obtener un modelo del geoide gravimétrico que presenta una mayor 'precisión' que los modelos geopotenciales disponibles, incluso superando la precisión del modelo geopotencial global EGM2008. ABSTRACT The geoid, defined as the equipotential surface that best fits (in the least squares sense) to the mean sea level at a particular time, is the surface used as a reference to determine the orthometric heights. If we have an equipotential reference surface or a precise local geoid, we can then determine the orthometric heights efficiently from the ellipsoidal heights, provided by the Global Navigation Satellite System (GNSS). One of the most common and important an unsolved problem in geodesy is the lack of a global altimetric datum (Sjoberg, 2011)) with the appropriate precision. In the absence of one which allows us to obtain the absolute values of the geoid undulation with the required precision, it is necessary to use alternative geopotential models. The EGM2008 was recently published, in which there has been a marked improvement of its three data sources, so this model contains additional coefficients of degree up to 2190 and order 2159, and there is a substantial improvement in accuracy (Pavlis et al., 2008). When a given region has gravity values and high quality digital terrain models (DTM), it is possible to obtain more accurate regional geopotential models, with a higher resolution and precision, than global geopotential models. It is true that the National Geodetic Survey of the United States of America (NGS) has been developing geoid models for the region of the continental United States of America and its territories from the nineties, but which is also true is that areas such as Puerto Rico and the U.S. Virgin Islands have lagged behind when to apply and get more accurate results with these regional geopotential models. Right now, the available geopotential model for Puerto Rico and the U.S. Virgin Islands is the GEOID12A (Roman y Weston, 2012). Given this need and given the uncertainty of knowing the behavior of a regional geoid model developed exclusively with data from local gravity, we have taken on the task of developing a gravimetric geoid model to use as a reference system for orthometric heights. To develop a gravimetric geoid model in the island of Puerto Rico, implementing a methodology that allows us to analyze and validate the existing terrestrial gravity data is a must. Using altimetry validation with GIS and mathematical validation by collocation with the Gravsoft suite programs (Tscherning et al., 1994) in its Python version (Nielsen et al., 2012), it was possible to validate 1673 observations with gravity anomalies values out of a total of 1894 observations obtained from the International Bureau Gravimetric (BGI ) database. Applying these methodologies allowed us to obtain a database of reliable gravity anomalies, which can be used for many applications in science and engineering. Given the low density of existing gravity data, it was necessary to employ an alternative method for densifying the existing gravity anomalies set. Employing the methodology proposed by Jekeli et al. (2009b) we proceeded to determine gravity anomaly data from a DTM. These anomalies were adjusted by using the validated free-air gravity anomalies and, after that, applying the best fit in the least-square sense by geographical area, it was possible to obtain a uniform grid of free-air anomalies obtained from a DTM. After applying the topographic corrections, determining the indirect effect of topography and the contribution of the global geopotential model EGM2008, a grid of residual anomalies was obtained. These residual anomalies were used to determine the gravimetric geoid by using various techniques, among which are the planar approximation of the Stokes function and the modifications of the Stokes kernel, proposed by Wong y Gore (1969), Vanicek y Kleusberg (1987) and Featherstone et al. (1998). After determining the different gravimetric geoid models, it was necessary to validate them by using a series of stations of the Puerto Rico Vertical Datum of 2002 (PRVD02) leveling network. These stations had published its values of ellipsoidal height and elevation, and in the absence of orthometric heights, we use the elevations obtained from first - order leveling to determine the geometric geoid undulation (Roman et al., 2013). After determine a total of 990 baselines, two analyzes were performed to determine the ' accuracy ' of the geoid models. The first analysis was to analyze the differences between the increments of the geometric geoid undulation with the increments of the geoid undulation of the different geoid models (gravimetric models, EGM2008 and GEOID12A) in function of the distance between the validation stations. Through this analysis, it was determined that the model with the modified Stokes kernel given by Wong and Gore had the best 'accuracy' in 91,1% for the analyzed baselines. In the second analysis, in which we considered the 990 baselines, we analyze the differences between the increments of the geometric geoid undulation with the increments of the geoid undulation of the different geoid models (gravimetric models, EGM2008 and GEOID12A) finding that the model with the highest 'accuracy' was also the model with modifying Stokes kernel given by Wong and Gore. In this analysis, the Wong and Gore gravimetric geoid model presented an 'accuracy' of 0,027 meters in comparison with the 'accuracy' of global geopotential model EGM2008, which gave us an 'accuracy' of 0,031 meters, while the 'accuracy ' of the GEOID12A regional model was 0,057 meters. Finally we can say that the methodology presented here is adequate as it was possible to obtain a gravimetric geoid model that has a greater 'accuracy' than the geopotential models available, even surpassing the accuracy of global geopotential model EGM2008.

Estudio geológico preliminar y reconstrucción paleoambiental de la cuenca endorreica de "El Hito" (Cuenca)

Mediante técnicas geofísicas (S.E.V.) y la caracterización hidroquímica de las aguas (determinación de aniones predominantes), se han obtenido datos sobre la estratigrafía y el funcionamiento de la Laguna efímera de El Hito (Cuenca), situada sobre yesos, y próxima al vecino emplazamiento del Almacén Temporal Centralizado (ATC) en Villar de Cañas. Asimismo, a partir del estudio del registro sedimentario de un sondeo manual en el que se recogieron muestras en las que se determinaron los compuestos orgánicos se realizó la reconstrucción de las condiciones paleoambientales. ABSTRACT Through geophysics techniques like vertical and electrical drillings, and hydrochemistry characterization of the waters (development of main anions), it has been obtained some data related to the stratigraphy and performance of the ephemeral lake in “El Hito”, Cuenca, Spain. El Hito´s lake is placed on a basin of plasters and it is next to site of the Centralized Temporary Storage in Villar de Cañas, Cuenca, Spain. Additionally, manual drillings will be conducted by collecting samples to determine the organic compounds in order to carry out a reconstruction of the paleoenvironmental conditions.

Fabrication of sub-100 nm IDT SAW devices on insulating, semiconducting and conductive substrates

This work describes the electron-beam (e-beam) lithography process developed to manufacture nano interdigital transducers (IDTs) to be used in high frequency (GHz) surface acoustic wave (SAW) applications. The combination of electron-beam (e-beam) lithography and lift-off process is shown to be effective in fabricating well-defined IDT finger patterns with a line width below 100 nm with a good yield. Working with insulating piezoelectric substrates brings about e-beam deflection. It is also shown how a very thin organic anti-static layer works well in avoiding this charge accumulation during e-beam lithography on the resist layer. However, the use of this anti-static layer is not required with the insulating piezoelectric layer laying on a semiconducting substrate such as highly doped silicon. The effect of the e-beam dose on a number of different layers (of insulating, insulating on semiconducting, semiconducting, and conductive natures) is provided. Among other advantages, the use of reduced e-beam doses increases the manufacturing time. The principal aim of this work is to explain the interrelation among e-beam dose, substrate nature and IDT structure. An extensive study of the e-beam lithography of long IDT-fingers is provided, in a wide variety of electrode widths, electrode numbers and electrode pitches. It is worthy to highlight that this work shows the influence of the e-beam dose on five substrates of different conductive nature

Conductive-tether design for de-orbiting from given altitude and inclination

A bare tether with thin-tape cross section is both i) the most effective electrodinamic tether for given length and mass, and ii) capable of effective design for an arbitrary mission through its three disparate dimensions. It handily beats the fully insulated tether that exchanges current at both ends, a result resting in advantages of 2D current collection as against 3D collection; it has much greater perimeter than the round bare tether and much lower fatal debris-impact rate, leading to greatly faster de-orbiting and greatly higher probability of survival; and it only allows multi-line tethers reaching a few hundred lines to stand competitive. In selecting the disparate values of length L, width w, and thickness h for a de-orbit mission, performance involves three criteria: a) tether-tospacecraft mass ratio must be small; b) probability of survival against the debris environment must be high; and c) de-orbiting must be fast to reduce manoeuvres for avoiding catastrophic collisions with big active/passive satellites around. Beyond determining tether mass through the product Lwh, main dimension parameters affecting performance are L/h2li characterizing ohmic effects, and w determining electron collection. An algorithm for optimal selection of tape dimensions is elaborated.

Transient behavior of a system composed of conductive thin wire structures excited by harmonic and lightning type signals

The transient response of a system of independent electrodes buried in a semi-infinite conducting medium is studied. Using a simple and versatile numerical scheme written by the authors and based on the Electric Field Integral Equation (EFIE), the effect caused by harmonic signals ranging on frequency from Hz to hundred of MHz, and also by lightning type driving signal striking at a remote point far from the conductors, is extensively studied. The value of the scalar potential appearing on the electrodes as a function of the frequency of the applied signal is one of the variables investigated. Other features such as the input impedance at the injection point of the signal and the Ground Potential Rise (GPR) over the electrode system are also discussed