A comparison between PML, infinite elements and an iterative BEM as mesh truncation methods for HP self-adaptive procedures in electromagnetics

Finite element hp-adaptivity is a technology that allows for very accurate numerical solutions. When applied to open region problems such as radar cross section prediction or antenna analysis, a mesh truncation method needs to be used. This paper compares the following mesh truncation methods in the context of hp-adaptive methods: Infinite Elements, Perfectly Matched Layers and an iterative boundary element based methodology. These methods have been selected because they are exact at the continuous level (a desirable feature required by the extreme accuracy delivered by the hp-adaptive strategy) and they are easy to integrate with the logic of hp-adaptivity. The comparison is mainly based on the number of degrees of freedom needed for each method to achieve a given level of accuracy. Computational times are also included. Two-dimensional examples are used, but the conclusions directly extrapolated to the three dimensional case.

A comparative analysis between FEM and Boundary Methods in bending of Plates

Two different methods of analysis of plate bending, FEM and BM are discussed in this paper. The plate behaviour is assumed to be represented by using the linear thin plate theory where the Poisson-Kirchoff assumption holds. The BM based in a weighted mean square error technique produced good results for the problem of plate bending. The computational effort demanded in the BM is smaller than the one needed in a FEM analysis for the same level of accuracy. The general application of the FEM cannot be matched by the BM. Particularly, different types of geometry (plates of arbitrary geometry) need a similar but not identical treatment in the BM. However, this loss of generality is counterbalanced by the computational efficiency gained in the BM in the solution achievement

Analysis of the railway track as a spatially periodic structure

This article presents a new and computationally efficient method of analysis of a railway track modelled as a continuous beam of 2N spans supported by elastic vertical springs. The main feature of this method is its important reduction in computational effort with respect to standard matrix methods of structural analysis. In this article, the whole structure is considered to be a repetition of a single one. The analysis presented is applied to a simple railway track model, i.e. to a repetitive beam supported on vertical springs (sleepers). The proposed method of analysis is based on the general theory of spatially periodic structures. The main feature of this theory is the possibility to apply Discrete Fourier Transform (DFT) in order to reduce a large system of q(2N + 1) linear stiffness equilibrium equations to a set of 2N + 1 uncoupled systems of q equations each. In this way, a dramatic reduction of the computational effort of solving the large system of equations is achieved. This fact is particularly important in the analysis of railway track structures, in which N is a very large number (around several thousands), and q = 2, the vertical displacement and rotation, is very small. The proposed method allows us to easily obtain the exact solution given by Samartín [1], i.e. the continuous beam railway track response. The comparison between the proposed method and other methods of analysis of railway tracks, such as Lorente de Nó and Zimmermann-Timoshenko, clearly shows the accuracy of the obtained results for the proposed method, even for low values of N. In addition, identical results between the proposed and the Lorente methods have been found, although the proposed method seems to be of simpler application and computationally more efficient than the Lorente one. Small but significative differences occur between these two methods and the one developed by Zimmermann-Timoshenko. This article also presents a detailed sensitivity analysis of the vertical displacement of the sleepers. Although standard matrix methods of structural analysis can handle this railway model, one of the objectives of this article is to show the efficiency of DFT method with respect to standard matrix structural analysis. A comparative analysis between standard matrix structural analysis and the proposed method (DFT), in terms of computational time, input, output and also software programming, will be carried out. Finally, a URL link to a MatLab computer program list, based on the proposed method, is given

Performance Comparison Between Serrated Edge and Rolled Edge Reflectors Inside CATR Facilities

CATR facilities are attractive antenna measurement facilities. Main reasons which contribute to this fact lie on its inherent reduced volume, on-the-fly measurements and the extension of both to a wide range of frequencies. However, these features rely on the assumption that the field collimation scheme is able to generate a plane wave distribution (quiet zone) where the AUT is to be placed and operated in RX mode. Unfortunately, electromagnetic theory states that this field distribution is not possible to be generated by a finite size scatterer operated as the collimator of a nonzero wavelength time-harmonic propagating field. This is the background of this paper, where two well-known electromagnetic field collimators will be discussed: the serrated edge reflector and the blended rolled edge reflector. To reach this purpose, electromagnetic hybrid analysis techniques developed at Technical University of Madrid will be applied.

Energy payback time of grid connected pv systems: comparison between tracking and fixed systems

A review of existing studies about LCA of PV systems has been carried out. The data from this review have been completed with our own figures in order to calculate the Energy Payback Time of double and horizontal axis tracking and fixed systems. The results of this metric span from 2 to 5 years for the latitude and global irradiation ranges of the geographical area comprised between −10◦ to 10◦ of longitude, and 30◦ to 45◦ of latitude. With the caution due to the uncertainty of the sources of information, these results mean that a GCPVS is able to produce back the energy required for its existence from 6 to 15 times during a life cycle of 30 years. When comparing tracking and fixed systems, the great importance of the PV generator makes advisable to dedicate more energy to some components of the system in order to increase the productivity and to obtain a higher performance of the component with the highest energy requirement. Both double axis and horizontal axis trackers follow this way, requiring more energy in metallic structure, foundations and wiring, but this higher contribution is widely compensated by the improved productivity of the system.

Impact of Nuclear Data Uncertainties on Advanced Fuel Cycles and Their Irradiated Fuel - A comparison between Libraries

The uncertainties on the isotopic composition throughout the burnup due to the nuclear data uncertainties are analysed. The different sources of uncertainties: decay data, fission yield and cross sections; are propagated individually, and their effect assessed. Two applications are studied: EFIT (an ADS-like reactor) and ESFR (Sodium Fast Reactor). The impact of the uncertainties on cross sections provided by the EAF-2010, SCALE6.1 and COMMARA-2.0 libraries are compared. These Uncertainty Quantification (UQ) studies have been carried out with a Monte Carlo sampling approach implemented in the depletion/activation code ACAB. Such implementation has been improved to overcome depletion/activation problems with variations of the neutron spectrum.

Biosensing comparison between different geometries based on vertical submicron-structrures made of SU-8 resist

Previous work of the research group [1-4] demonstrated the viability of using periodic lattices of micro and nanopillars, called Bio-photonic sensing Cells (BICELLs), as an optical biosensor vertically characterized by visible spectrometry. Also we have studied theoretically [5] the performance of the BICELLs by 2D and 3D simulation in orde r to optimize the biosensing response. In this work we present the fabrication and biosensing comparison of different geometrical parameters on periodic lattices of pillars in order to discuss theoretical conclusions with these results. In this way, we have explored the biosensing response of other patter ns such as crosses, stars, cylinders, concentrical cylinders (Figure 1). Also we introduced a novel method to test the BICELLs in a cost-effective way by using an ultra-thin film of SU-8 spin-coated onto the patterns to reproduce the effect of a biofilm attached to the biosensor surface. Finally we have tested the biosensing response of the different geometries by the well-known Bovine Serum Albumin (BSA) immunoassay and compared with the theoretical simulation.

A study of feature combination for vehicle detection based on image processing

Video analytics play a critical role in most recent traffic monitoring and driver assistance systems. In this context, the correct detection and classification of surrounding vehicles through image analysis has been the focus of extensive research in the last years. Most of the pieces of work reported for image-based vehicle verification make use of supervised classification approaches and resort to techniques, such as histograms of oriented gradients (HOG), principal component analysis (PCA), and Gabor filters, among others. Unfortunately, existing approaches are lacking in two respects: first, comparison between methods using a common body of work has not been addressed; second, no study of the combination potentiality of popular features for vehicle classification has been reported. In this study the performance of the different techniques is first reviewed and compared using a common public database. Then, the combination capabilities of these techniques are explored and a methodology is presented for the fusion of classifiers built upon them, taking into account also the vehicle pose. The study unveils the limitations of single-feature based classification and makes clear that fusion of classifiers is highly beneficial for vehicle verification.

Dynamic topic-based adaptation of language models: a comparison between different approaches

This paper presents a dynamic LM adaptation based on the topic that has been identified on a speech segment. We use LSA and the given topic labels in the training dataset to obtain and use the topic models. We propose a dynamic language model adaptation to improve the recognition performance in "a two stages" AST system. The final stage makes use of the topic identification with two variants: the first on uses just the most probable topic and the other one depends on the relative distances of the topics that have been identified. We perform the adaptation of the LM as a linear interpolation between a background model and topic-based LM. The interpolation weight id dynamically adapted according to different parameters. The proposed method is evaluated on the Spanish partition of the EPPS speech database. We achieved a relative reduction in WER of 11.13% over the baseline system which uses a single blackground LM.

Comparison and Assessment of Two Emission inventories for the Madrid Region

Emission inventories are databases that aim to describe the polluting activities that occur across a certain geographic domain. According to the spatial scale, the availability of information will vary as well as the applied assumptions, which will strongly influence its quality, accuracy and representativeness. This study compared and contrasted two emission inventories describing the Greater Madrid Region (GMR) under an air quality simulation approach. The chosen inventories were the National Emissions Inventory (NEI) and the Regional Emissions Inventory of the Greater Madrid Region (REI). Both of them were used to feed air quality simulations with the CMAQ modelling system, and the results were compared with observations from the air quality monitoring network in the modelled domain. Through the application of statistical tools, the analysis of emissions at cell level and cell – expansion procedures, it was observed that the National Inventory showed better results for describing on – road traffic activities and agriculture, SNAP07 and SNAP10. The accurate description of activities, the good characterization of the vehicle fleet and the correct use of traffic emission factors were the main causes of such a good correlation. On the other hand, the Regional Inventory showed better descriptions for non – industrial combustion (SNAP02) and industrial activities (SNAP03). It incorporated realistic emission factors, a reasonable fuel mix and it drew upon local information sources to describe these activities, while NEI relied on surrogation and national datasets which leaded to a poorer representation. Off – road transportation (SNAP08) was similarly described by both inventories, while the rest of the SNAP activities showed a marginal contribution to the overall emissions.

Woolliness assessment in peaches. Comparison between human and instrumental procedures and results

Woolliness, a negative attribute of sensory texture, is characterised by the lack of juiciness without variation of the tissue water content an incapacity of ripening although there is external ripe appearance. In this study, peaches cv Springcrest (early and soft flesh peaches) and Miraflores (late and hard flesh peaches) corresponding to three different maturity stages at harvest, stored 0, 1, 2, 3 and 4 weeks at 1 and 5°C have been tested by instrumental and sensory means. A Instrumental classification of woolliness has been compared to the sensory assessment. For Springcrest peaches the sensory results match with those found for the instrumental procedure. In this case , Woolliness appears after 2 weeks of storage at 5°C, changing abruptly from crispy to woolly. Miraflores peaches did not develop woolliness during storage. After comparing with sensory results, it is shown that a common instrumental scale may be appropriate to classify for woolliness all peach varieties.

Energy efficiency: comparison between the CALENER certificate and real consumptions

Modelización de una vivienda sostenible y comparación con los resultados obtenidos con los programas reconocidos en España de certificación.

Comparison between SAM and Thermoflow for Linear Fresnel Solar Power Plants design

System Advisor Model is a software tool develped by National Renewable Laboratory (NREL), Department Of Energy, USA to design Solar Power Plants.

Identificación de áreas prioritarias para la conservación de razas de maíz en la sierra de Ecuador

En Ecuador el maíz es el cultivo más importante en superficie y es base de la alimentación para la población rural que vive en los Andes. A diferencia de lo que sucede en la Costa, en la región Sierra todavía se cultivan numerosas variedades tradicionales que se agrupan en veinticuatro razas. Mantener esta diversidad es, pues, de gran importancia no solo para la seguridad alimentaria, sino también como fuente de genes para tolerancia a factores abióticos que podrían ser incorporados a las variedades modernas. Si bien parte de esta diversidad fue recolectada a mediados del siglo pasado y está siendo conservada en distintos bancos de germoplasma, es deseable que su conservación in situ también esté asegurada, entre otras razones, porque de esta manera el cultivo puede seguir evolucionando. Para poder implementar un plan de conservación en finca que contribuya a preservar este patrimonio, resulta imprescindible identificar áreas idóneas donde concentrar los recursos y conocer las características y tipologías de los agricultores que manejan la diversidad actual. Generar esta información es el objetivo principal de esta investigación y para lograrlo se han llevado a cabo cuatro estudios: (1) Análisis de la diversidad a nivel de razas e identificación de áreas de alta riqueza de razas, alta diversidad morfológica y/o alta diversidad ecogeográfica en la Sierra de Ecuador, (2) Identificación del perfil y las características de los agricultores que conservan y manejan las variedades tradicionales de maíz en la Sierra de Ecuador, (3) Análisis del conocimiento local, manejo y usos de variedades tradicionales de maíz en la Sierra de Ecuador, y (4) Identificación de áreas de alta diversidad y bajo riesgo de pérdida para la conservación en finca de maíz en la Sierra de Ecuador. Para el primer estudio se visitaron 303 fincas distribuidas a lo largo de la Sierra y se recolectaron 636 muestras que fueron caracterizadas morfológicamente mediante 14 variables: 8 relacionadas con la mazorca (forma, longitud y diámetro de la mazorca, color y diámetro de olote y número y disposición de hileras) y 7 referidas el grano (número total de granos, color, forma, longitud, anchura y grosor de grano y tipo de endospermo). Adicionalmente, las fincas donde se tomaron las muestras fueron caracterizadas ecogeográficamente mediante 5 variables climáticas (temperatura media estacional, rango de temperatura media anual, temperatura mínima de diciembre, precipitación estacional y precipitación de octubre), 2 geofísicas (altitud y pendiente) y 5 edáficas (textura principal del suelo, profundidad a roca, pH, contenido en materia orgánica y fertilidad). A partir de esta información y mediante técnicas de sistemas de información geográfica (SIG), se generaron mapas de distribución por raza en formato vectorial y un mapa de riqueza de razas, un mapa de diversidad morfológica y un mapa de diversidad ecogeográfica en formato ráster con celdas de 10 km x 10 km. Los resultados permitieron constatar que, en los últimos 60 años, no se ha perdido ninguna raza. Sin embargo, Canguil, Chaucho y Clavito han dejado de cultivarse en algunas provincias con la consiguiente erosión genética del cultivo. La caracterización morfológica detectó diferencias en el grado de variabilidad intra-raza, siendo Patillo Ecuatoriano, Racimo de Uva y Uchima las razas más heterogéneas tanto para los caracteres cualitativos como cuantitativos. A nivel climático y geofísico, también se detectaron diferencias en el grado de variación intra-raza; Cuzco Ecuatoriano, Kcello Ecuatoriano y Montaña Ecuatoriana fueron las razas que en promedio presentaron mayores rangos y coeficientes de variación para estas variables ecogeográficas. En cuanto a las condiciones edáficas todas las razas, excepto Cónico Dentado, presentaron una gran heterogeneidad, pudiendo crecer tanto en suelos ricos como pobres, con valores de pH entre ácido y moderadamente alcalino. La comparación entre razas reveló diferencias significativas en los rangos ambientales de algunas razas como Cónico Dentado, que tiende a cultivarse a menor altitud y, por tanto, en ambientes menos fríos y de mayor precipitación que Blanco Blandito, Patillo Ecuatoriano, Sabanero Ecuatoriano, Uchima y Zhima. Para la mayoría de las razas se encontraron materiales potencialmente adaptados a condiciones de estrés (precipitación estacional inferior a 500 mm y suelos con pH entre 4.5 y 5.5). Finalmente, los mapas de riqueza, de diversidad morfológica y de diversidad ecogeográfica mostraron 36 celdas de alta diversidad repartidas en las 10 provincias de la Sierra: 11 celdas en las provincias del norte, 11 en las provincias del centro y 14 en las provincias del sur. Para la caracterización e identificación de las tipologías de los agricultores que cultivan maíz en la Sierra de Ecuador y el análisis de los posibles factores de riesgo de pérdida de diversidad, se realizaron entrevistas individuales y semiestructuradas a los agricultores dueños de las fincas donde se recolectaron las muestras para el estudio de diversidad (254 en total). Las preguntas que se formularon (11 abiertas y 5 cerradas) estuvieron organizadas en seis bloques: datos del agricultor, características de la finca, diversidad y conocimiento del cultivo, manejo del cultivo, usos y flujo de semillas. Los resultados indicaron que la diversidad de maíz que hay en la Sierra de Ecuador es manejada mayoritariamente por agricultores mestizos, de entre 30 y 55 años, que cultivan una o dos variedades tradicionales para autoconsumo, en parcelas de menos de 0.5 ha y en asocio con fréjol. El análisis de segmentación mediante el algoritmo Chi-square automatic interaction detection (CHAID) permitió identificar un pequeño grupo de agricultores indígenas con parcelas medianas (entre 0.5 ha y 1.5 ha) que conservan un mayor número de variedades tradicionales por finca que el agricultor promedio. Los análisis estadísticos no detectaron diferencias significativas entre etnias (mestizo vs. indígena), géneros (hombre vs. mujer) y grupos de edad (jóvenes menores de 30 años, adultos entre 30 y 55 años y adultos mayores de 55 años) en lo que respecta al conocimiento del cultivo (criterios de reconocimiento y razones de preferencia) y manejo (tipo de cultivo), pero sí detectaron diferencias entre regiones, principalmente en el modo de cultivar el maíz; mientras que en el norte y sur tienden a sembrarlo en asocio y con un mayor número de especies, en el centro acostumbran a cultivarlo preferentemente solo. En cuanto a los usos, se recopilaron hasta 39 modos diferentes de consumir maíz, siendo Kcello Ecuatoriano y Zhima las razas para las que se registró un mayor número de usos. La comparación del número medio de usos por variedad entre etnias evidenció que los agricultores mestizos utilizan sus variedades tradicionales de forma más variada que los indígenas. Entre los factores de riesgo que se analizaron, el bajo porcentaje de jóvenes agricultores que se ocupan de las fincas podría suponer una amenaza a medio plazo por falta de relevo generacional. Adicionalmente, las numerosas sinonimias y homonimias que se detectaron y el bajo intercambio de semillas también podrían ser causa de pérdida de diversidad, bien por reemplazo o por envejecimiento de la semilla. Finalmente, se concluyó que las razas Chaucho, Complejo Chillo-Huandango, Complejo Mishca-Huandango, Cónico Dentado, Montaña Ecuatoriana y Sabanero Ecuatoriano son particularmente vulnerables, no solo por su baja presencia, sino también por el color de grano que tienen (los mismos que la mayoría de las razas más comunes) y carecer de nombres y usos específicos. Finalmente, para la priorización de áreas de conservación en finca para maíz en la Sierra de Ecuador, se utilizaron 13 criterios de diferente naturaleza: 2 ecogeográficos (precipitación, diversidad ecogeográfica), 6 biológicos (grado de presencia del cultivo, riqueza de razas, diversidad morfológica, presencia de mezclas, presencia de razas locales y riesgo de erosión genética), 3 culturales (abundancia de variedades por finca, diversidad de usos y frecuencia de intercambio) y 2 demográficos (tamaño de la población y distancia a núcleos urbanos). Mediante técnicas SIG y de evaluación multicriterio, los valores originales de las capas-criterio fueron transformados a una escala de 0 a 100. Posteriormente, las capas-criterio normalizadas fueron sumadas utilizando tres métodos de ponderación: (1) mismo peso, (2) diferente peso según la puntuación otorgada por 72 expertos, y (3) diferente peso según el método de comparación entre pares de criterios. Los resultados permitieron identificar ocho celdas de 10 km x 10 km con alta puntuación (> 65): tres celdas en el norte (una en cada una de las provincias), una celda en el centro (en la provincia de Cotopaxi), y cuatro celdas en la región sur (dos en Azuay y otras dos en Loja). ABSTRACT In Ecuador, the maize is the most important cultivation in surface and it is a base of the feeding for the rural population who lives in the Andes. In contrast to what it happens on the Coast, in the Sierra region still there are cultivated numerous traditional varieties that are grouped into twenty-four races. Maintaining this diversity is, therefore, of great importance not only for food security, but also as a source of genes for tolerance to abiotic factors could be incorporated into modern varieties. Although part of this diversity was collected in the middle of the last century and is still preserved in various germplasm banks, it is desirable for the in situ conservation also is assured, among other reasons, because in this way the crop can continue to evolve. To be able to implement a conservation plan on farm that contribute to preserving this heritage, it is essential to identify suitable areas where to concentrate resources and know the characteristics and typology of farmer who managed the current diversity. To generate this information is the main target of this investigation and to achieve this, four studies have been carried out: (1) Analysis of the diversity at races and identification of areas of high richness of races, high morphological diversity and / or ecogeographical high diversity in the Sierra of Ecuador, (2) Identification of the profile and characteristics of farmers who conserve and manage traditional varieties of maize in the Sierra of Ecuador, (3) Analysis of local knowledge, management and use of traditional varieties of maize in the Sierra of Ecuador, and (4) Identification of areas of high diversity and low risk of loss for the conservation of maize in the Sierra of Ecuador. For the first study were visited 303 farms distributed along the Sierra and collected 636 samples that were characterized morphologically by 14 variables: 8 related to the ear (shape, length and diameter of the cob, colour, and diameter of cob and number and arrangement of rows) and 7 referred to the grain (total number of grain, colour, shape, length, width, and thickness and type of grain endosperm). In addition, the farms where the samples were taken were characterized ecogeographically through 5 climatic variables (seasonal average temperature, range of average annual temperature, minimum temperature for December, seasonal precipitation and precipitation of October), 2 geophysical (altitude and slope) and edaphic 5 (main texture of the soil, deep rock, pH, content of organic matter and fertility). From this information and techniques of geographic information systems (GIS), maps were generated for distribution by race in vector format and a map of richness of races, a map of morphological diversity and a map of ecogeographical diversity in raster format with cells of 10 km x 10 km. The results allowed observing that, over the past 60 years, it has not lost any race. Nevertheless, Canguil, Chaucho and Clavito have stopped being cultivated in some provinces with the consequent genetic erosion of the cultivation. The morphological characterization detected differences in the degree of variability intra-race, being Patillo Ecuatoriano, Racimo de Uva and Uchima races more heterogeneous both for the qualitative and quantitative characters. At climate and geophysical level, also detected differences in the degree of variation intra-race; Cuzco Ecuatoriano, Kcello Ecuatoriano and Montaña Ecuatoriana were races that, on average, showed higher ranges and coefficients of variation for these geographical characters. In terms of the edaphic conditions, all races, except Cónico Dentado, showed a great heterogeneity, and can grow both in rich and poor soils, with pH values between acid and moderately alkaline. The comparison between races revealed significant differences in the environmental ranges in some races as Cónico Dentado, which tends to be grown at lower elevations and, therefore, in environments less cold and greater precipitation than Blanco Blandito, Patillo Ecuatoriano, Sabanero Ecuatoriano, Uchima and Zhima. For most of the races were found materials potentially adapted to stress conditions (seasonal precipitation less than 500 mm and soil with a pH between 4.5 and 5.5). Finally, the maps of richness, morphologic diversity and ecogeographical diversity showed 36 cells high diversity distributed in 10 provinces of the Sierra: 11 cells in the northern provinces, 11 in the central provinces and 14 in the southern provinces. For the characterization and identification of the typology of the farmers who cultivate corn in the Sierra of Ecuador and the analysis of the possible factors of risk of loss of diversity, there were realized interviews individual and semistructured to the farmers’ owners of the farms where the samples were gathered for the study of diversity (254 in whole). The questions that were formulated (11 opened ones and 5 closed ones) were organized in six blocks: data of the farmer, characteristics of the farm, diversity and knowledge of the crop, crop management, uses and seed flow. The results indicated that the maize diversity that exist in the Sierra of Ecuador is managed mainly by mestizo farmers, aged between 30 and 55, who cultivate one or two traditional varieties for self-consumption, on plots of less than 0.5 has and in associated with beans. The segmentation analysis algorithm using the Chi-square automatic interaction detection (CHAID technique), allowed to identify a small group of indigenous farmers with medium-sized plots (between 0.5 there is and 1.5 it is) that a major number of traditional varieties preserves for farm that the average farmer. The statistical analysis did not detect significant differences between ethnic groups (mestizos vs. indigenous), genres (man vs. women) and age groups (young people under 30 years of age, adults between 30 and 55 years and adults over 55 years old) in regards to the knowledge of the cultivation (recognition criteria and reasons of preference) and management (type of crop), but if detected differences between regions, mainly on the mode of cultivating the maize; while in the north and south they tend to sow in associate and with a greater number of species, in the center accustomed to cultivate it preferably only. In regards to the uses, they were compiled up to 39 different ways of consuming maize, being Kcello Ecuatoriano and Zhima the races for which a major number of uses registered. The comparison of the average number of uses per variety between ethnic groups showed that the mestizo farmers used their traditional varieties of form more varied than the indigenous people. Between the factors of risk that were analyzed, the low percentage of young farmers who deal with the farms might suppose a medium-term threat for lack of generational relief. In addition, the numerous synonyms and homonyms that were detected and the low seed exchange could also be a cause of loss of diversity, either by replacement or by aging of the seed. Finally, it was concluded that the races Chaucho, Complex Chillo-Huandango, Complex Mishca-Huandango, Cónico Dentado, Montaña Ecuatoriana and Sabanero Ecuatoriano are particularly vulnerable, not only because of their low presence, but also by the grain color they have (the same as the majority of races more common) and lack of names and specific uses. Finally, for the prioritization of maize conservation areas on farm in the Sierra of Ecuador, used 13 criteria of different nature: 2 ecogeographic (precipitation, diversity ecogeographical), 6 biological (degree of presence of the crop, races richness, morphological diversity, the presence of mixtures, presence of local races and risk of genetic erosion), 3 cultural (abundance of varieties per farm, diversity of uses and frequency of exchange) and 2 demographic (population size and distance to urban centers). Using GIS techniques and multicriteria evaluation, the original values of the layers-criterion were transformed to a scale of 0 to 100. Later, the normalized layers - criteria were added using three weighting methods: (1) the same weight, (2) different weight according to the score given by 72 experts, and (3) different weight according to the method of comparison between pairs of criteria. The results allowed to identify eight 10 km cells x 10 km with high punctuation (> 65): three cells in the north (one in each of the provinces), a cell in the center (in the Cotopaxi province), and four cells in the south region (two in Azuay and other two in Loja).

Papyrus, EATOP, and MetaEdit+: a comparison between the EAST-ADL modeling tools

Several Architecture Description Languages (ADLs) are emerging as models to describe and represent system architectures. Among others, EAST-ADL language is highlighted. It represents an abstraction of embedded software systems for automobiles. Given the need to implement the EAST-ADL language, there are many modeling tools to perform this task. The scope of this thesis is a detailed comparison of three EAST-ADL editors: Papyrus, EATOP and MetaEdit +, providing a conceptual framework, describing the comparison criteria, and finally exemplifying thanks to the Brake-By-Wire use case which has been provided, and whose development is not the subject of this project. The motivation for developing this project is to provide comparison guide between these three modeling tools to facilitate developers choice when deciding the tool in which develop their work. RESUMEN. Diversos Lenguajes de Descripción de Arquitecturas (ADLs) están surgiendo como modelos para describir y representar arquitecturas de sistemas. Entre ellos es destacado el lenguaje EAST-ADL, que representa una abstracción de los sistemas de software embebido para automóviles. Ante la necesidad de implementar el lenguaje EAST-ADL, han surgido diversas herramientas de modelado que llevan a cabo esta tarea. El alcance de este proyecto consiste en una comparación detallada de tres editores EAST-ADL: Papyrus, EATOP y MetaEdit+, proporcionando un marco conceptual, describiendo los criterios de comparación y finalmente ejemplificando con el caso de uso Brake-By-Wire que nos ha sido proporcionado, y cuyo desarrollo no es sujeto de este proyecto. La motivación para desarrollar este proyecto parte de proporcionar al usuario una guía comparativa de estas tres herramientas de modelado para facilitar su elección a la hora de desarrollar su trabajo.