Alarm tree analysis using statistical techniques

This work presents a systematic method for the generation and treatment of the alarms' graphs, being its final object to find the Alarm Root Cause of the Massive Alarms that are produced in the dispatching centers. Although many works about this matter have been already developed, the problem about the alarm management in the industry is still completely unsolved. In this paper, a simple statistic analysis of the historical data base is conducted. The results obtained by the acquisition alarm systems, are used to generate a directed graph from which the more significant alarms are extracted, previously analyzing any possible case in which a great quantity of alarms are produced.

Traffic uncertainty in toll motorway concessions in Spain

This study assessed the inaccuracy of the traffic estimates for toll motorway concessions in Spain. It was found that the estimates conducted by both the government and the concessionaire showed a significant bias towards overestimating traffic. The level of overestimation in Spain is even greater than that reported by other studies based on worldwide data. The notorious levels of overestimation entail severe burdens to the economics of the concessionaires that often prompt renegotiations of the contracts, which are often accepted by the government. These renegotiations usually end up with toll changes or extension of the concession terms, which have to be ultimately borne by future motorway users. It is postulated herein that the bias towards overestimating traffic in toll motorways in Spain is mostly caused by strategic issues rather than by modelling errors.

Rebalancing urban mobility: a tale of four cities

The key of mobility in urban planning is not in dispute. Integrated strategies that take into account the interrelations among land use, transport supply and demand and the different transportation modes are more necessary than ever. In Europe, regulatory tools such as local mobility plans or traffic plans have been enforced for a long time, evolving into so-called sustainable urban transport plans (SUTP) ? that is, plans thatmerge urban planning,mobility governance, social awareness and environmental safeguards to develop a vision based on sustainability and equity. Indeed, SUTP are aimed at solving typical problems in current land use, such as urban sprawl, which make clear the need for a paradigm shift from transport (or mobility) planning to land use (or city) planning, thereby producing urban mobility plans that are fully aligned with integrated urban development plans. This paper describes how SUTP are articulated across Europe according to four case studies: Peterborough (UK), Chambe¿ry (France), Ferrara (Italy) and Pinto (Spain), to highlight variations and commonalities, both among the four national legal frameworks and the actual planning processes at the local level. Objectives, measures and indicators used in the monitoring and evaluation phases have been analysed and the results assessed. The main conclusion of the paper is that, as seen in these real-life examples, the lack of integration between spatial planning and transport strategies results in the unsustainability of urban areas and, therefore, in a significant loss of competitiveness.

Comparative study of breakwater crown wall – calculation methods

An investigation was undertaken consisting of a state-of-the-art and comparative analysis of currently available methods for calculating the structural stability of wave walls in sloping breakwaters. A total of six design schemes are addressed. The conditions under which the formulations and ranges of validity are explicitly indicated by their authors, are given. The lack of definition in parameters to be used and aspects not taken into account in their investigations are discussed and the results of this analysis are given in a final table.

Whence and whereto?

Se trata de un artículo invitado en el que el Pr. Martí, miembro del comité editor de la revista, ofrece en base a su experiencia algunas reflexiones sobre el tema al que se orienta la revista.

Steady state analysis of a storage integrated solar thermophotovoltaic (SISTPV) system

This paper presents the theoretical analysis of a storage integrated solar thermophotovoltaic (SISTPV) system operating in steady state. These systems combine thermophotovoltaic (TPV) technology and high temperature thermal storage phase-change materials (PCM) in the same unit, providing a great potential in terms of efficiency, cost reduction and storage energy density. The main attraction in the proposed system is its simplicity and modularity compared to conventional Concentrated Solar Power (CSP) technologies. This is mainly due to the absence of moving parts. In this paper we analyze the use of Silicon as the phase change material (PCM). Silicon is an excellent candidate because of its high melting point (1680 K) and its very high latent heat of fusion of 1800 kJ/kg, which is about ten times greater than the conventional PCMs like molten salts. For a simple system configuration, we have demonstrated that overall conversion efficiencies up to ?35% are approachable. Although higher efficiencies are expected by incorporating more advanced devices like multijunction TPV cells, narrow band selective emitters or adopting near-field TPV configurations as well as by enhancing the convective/conductive heat transfer within the PCM. In this paper, we also discuss about the optimum system configurations and provide the general guidelines for designing these systems. Preliminary estimates of night time operations indicate it is possible to achieve over 10 h of operation with a relatively small quantity of Silicon.

Discussion: Comparative study of breakwater crown wall - calculation methods

This paper presents an extensive and useful comparison of existing formulas to estimate wave forces on crown walls. The paper also provides valuable insights into crown wall behaviour, suggesting the use of formulas for prior sizing and recommending, in any case, tests on a physical model in order to confirm the final design. The authors helpfully advise to use more than one method to obtain results closer to reality, always taking into account the test conditions under which each formula was developed

Road Dust Emission Sources and Assessment of Street Washing Effect

Although previous studies report on the effect of street washing on ambient particulate matter levels, there is a lack of studies investigating the results of street washing on the emission strength of road dust. A sampling campaign was conducted in Madrid urban area during July 2009 where road dust samples were collected in two sites, namely Reference site (where the road surface was not washed) and Pelayo site (where street washing was performed daily during night). Following the chemical characterization of the road dust particles the emission sources were resolved by means of Positive Matrix Factorization, PMF (Multilinear Engine scripting) and the mass contribution of each source was calculated for the two sites. Mineral dust, brake wear, tire wear, carbonaceous emissions and construction dust were the main sources of road dust with mineral and construction dust being the major contributors to inhalable road dust load. To evaluate the effectiveness of street washing on the emission sources, the sources mass contributions between the two sites were compared. Although brake wear and tire wear had lower concentrations at the site where street washing was performed, these mass differences were not statistically significant and the temporal variation did not show the expected build-up after dust removal. It was concluded that the washing activities resulted merely in a road dust moistening, without effective removal and that mobilization of particles took place in a few hours between washing and sampling. The results also indicated that it is worth paying attention to the dust dispersed from the construction sites as they affect the emission strength in nearby streets.

Comparison of Existing Formulae for Estimating the Overtopping Rate in Harbour Breakwaters

The purpose of the research work resulting from various studies undertaken in the CEDEX, as summarized in this article, is to make a comparative analysis of methods for calculating overtopping rates developed by different authors. To this effect, in the first place, existing formulae for estimating the overtopping rate on rubble mound and vertical breakwaters were summarised and analysed. Later, the above mentioned formulae were compared using the results obtained in a series of hydraulic model tests at the CEDEX (the Center of Studies of Ports and Coasts of the CEDEX, Madrid, Spain). A calculation method based on the neural network theory, developed in the European CLASH Project, was applied to a series of sloping breakwater tests in order to complete this research. The results obtained in the Ferrol, Ciervana and Alicante breakwaters tests are presented here.

Quality cost in bus operations based on activity-based costing

The study of service quality and its implication for transport contracts has several approaches in research and practical applications, where the main emphasis is the consideration of quality from the user's point of view, thus obtaining a customer satisfaction index as a measurement of the overall quality with no further implications for service providers. The main aim of this paper is to estimate the real economic impact of improving quality attributes for a bus operator. An application of the activity-based costing methodology is developed for a bus contract in Madrid, using quality data from surveys together with economic and performance information, and focusing on headway as a quality variable. Results show the consistency and practicality of this methodology, overcoming simplifications from traditional procedures. This method is a powerful tool in quality-based contracting as well as for effective investment in transport quality under poverty funding constraints

Night time performance of a storage integrated solar thermophotovoltaic (SISTPV) system

Energy storage at low maintenance cost is one of the key challenges for generating electricity from the solar energy. This paper presents the theoretical analysis (verified by CFD) of the night time performance of a recently proposed conceptual system that integrates thermal storage (via phase change materials) and thermophotovoltaics for power generation. These storage integrated solar thermophotovoltaic (SISTPV) systems are attractive owing to their simple design (no moving parts) and modularity compared to conventional Concentrated Solar Power (CSP) technologies. Importantly, the ability of high temperature operation of these systems allows the use of silicon (melting point of 1680 K) as the phase change material (PCM). Silicon's very high latent heat of fusion of 1800 kJ/kg and low cost ($1.70/kg), makes it an ideal heat storage medium enabling for an extremely high storage energy density and low weight modular systems. In this paper, the night time operation of the SISTPV system optimised for steady state is analysed. The results indicate that for any given PCM length, a combination of small taper ratio and large inlet hole-to-absorber area ratio are essential to increase the operation time and the average power produced during the night time. Additionally, the overall results show that there is a trade-off between running time and the average power produced during the night time. Average night time power densities as high as 30 W/cm(2) are possible if the system is designed with a small PCM length (10 cm) to operate just a few hours after sun-set, but running times longer than 72 h (3 days) are possible for larger lengths (50 cm) at the expense of a lower average power density of about 14 W/cm(2). In both cases the steady state system efficiency has been predicted to be about 30%. This makes SISTPV systems to be a versatile solution that can be adapted for operation in a broad range of locations with different climate conditions, even being used off-grid and in space applications.