A simplified energy consumption model for fiber-based Next Generation Access Networks

ICTs account nowadays for 2% of total carbon emissions. However, in a time when strict measures to reduce energyconsumption in all the industrial and services sectors are required, the ICT sector faces an increase in services and bandwidth demand. The deployment of NextGenerationNetworks (NGN) will be the answer to this new demand and specifically, the NextGenerationAccessNetworks (NGANs) will provide higher bandwidth access to users. Several policy and cost analysis are being carried out to understand the risks and opportunities of new deployments, though the question of which is the role of energyconsumption in NGANs seems off the table. Thus, this paper proposes amodel to analyze the energyconsumption of the main fiber-based NGAN architectures, i.e. Fiber To The House (FTTH) in both Passive Optical Network (PON) and Point-to-Point (PtP) variations, and FTTx/VDSL. The aim of this analysis is to provide deeper insight on the impact of new deployments on the energyconsumption of the ICT sector and the effects of energyconsumption on the life-cycle cost of NGANs. The paper presents also an energyconsumption comparison of the presented architectures, particularized in the specific geographic and demographic distribution of users of Spain, but easily extendable to other countries.

Polypropylene fiber-reinforced self-compacting concrete for the reconstruction of the cathedral of La Laguna, Canary Island, Spain

High performance materials are needed for the reconstruction of such a singular building as a cathedral, since in addition to special mechanical properties, high self compact ability, high durability and high surface quality, are specified. Because of the project’s specifications, the use of polypropylene fiber-reinforced, self-compacting concrete was selected by the engineering office. The low quality of local materials and the lack of experience in applying macro polypropylene fiber for structural reinforcement with these components materials required the development of a pretesting program. To optimize the mix design, performance was evaluated following technical, economical and constructability criteria. Since the addition of fibers reduces concrete self-compactability, many trials were run to determine the optimal mix proportions. The variables introduced were paste volume; the aggregate skeleton of two or three fractions plus limestone filler; fiber type and dosage. Two mix designs were selected from the preliminary results. The first one was used as reference for self-compactability and mechanical properties. The second one was an optimized mix with a reduction in cement content of 20 kg/m3and fiber dosage of 1 kg/m3. For these mix designs, extended testing was carried out to measure the compression and flexural strength, modulus of elasticity, toughness, and water permeability resistance

An alternative methodology to predict aging effects on the mechanical properties of glass fiber reinforced cement (GRC)

The effect of three different aging methods (immersion in hot water, freeze–thaw cycles and wet–dry cycles) on the mechanical properties of GRC were studied and compared. Test results showed that immersion in hot water may be an unreliable method for modified GRC formulations, with it being in probability a very harmful procedure. A new aging method, mixing freeze–thaw cycles and wet–dry cycles, seems to be the most accurate simulation of weather conditions that produce a noticeable change in GRC mechanical properties. Future work should be carried out to find a correlation between real weather and the proposed aging method.

Failure and impact behavior of facade panels made of glass fiber reinforced cement(GRC)

GRC is a cementitious composite material made up of a cement mortar matrix and chopped glass fibers. Due to its outstanding mechanical properties, GRC has been widely used to produce cladding panels and some civil engineering elements. Impact failure of cladding panels made of GRC may occur during production if some tool falls onto the panel, due to stone or other objects impacting at low velocities or caused by debris projected after a blast. Impact failure of a front panel of a building may have not only an important economic value but also human lives may be at risk if broken pieces of the panel fall from the building to the pavement. Therefore, knowing GRC impact strength is necessary to prevent economic costs and putting human lives at risk. One-stage light gas gun is an impact test machine capable of testing different materials subjected to impact loads. An experimental program was carried out, testing GRC samples of five different formulations, commonly used in building industry. Steel spheres were shot at different velocities on square GRC samples. The residual velocity of the projectiles was obtained both using a high speed camera with multiframe exposure and measuring the projectile’s penetration depth in molding clay blocks. Tests were performed on young and artificially aged GRC samples to compare GRC’s behavior when subjected to high strain rates. Numerical simulations using a hydrocode were made to analyze which parameters are most important during an impact event. GRC impact strength was obtained from test results. Also, GRC’s embrittlement, caused by GRC aging, has no influence on GRC impact behavior due to the small size of the projectile. Also, glass fibers used in GRC production only maintain GRC panels’ integrity but have no influence on GRC’s impact strength. Numerical models have reproduced accurately impact tests.

Effects of feeding strategy, fiber source of the diet, and crude protein content on productive performance of broiler breeder hens

A 12-wk experiment was conducted to investigate the effect of feeding program, dietary fiber, and CP content of the diet on productive performance of Ross broiler breeder hens (41 wk of age). There were 12 treatments arranged factorially with 2 levels of CP (14.5 vs. 17.4%), 3 fiber sources (0 vs. 3% inulin vs. 3% cellulose), and 2 levels of feed intake (160 vs. 208 g/d) that corresponded to restricted (R) or ad libitum (AL) feeding systems. The experimental diets contained 2,800 kcal ME with either 0.65 (14.5% CP) or 0.78% Lys (17.4% CP).

Curing, defects and mechanical performance of fiber-reinforced composites

Tradicionalmente, la fabricación de materiales compuestos de altas prestaciones se lleva a cabo en autoclave mediante la consolidación de preimpregnados a través de la aplicación simultánea de altas presiones y temperatura. Las elevadas presiones empleadas en autoclave reducen la porosidad de los componentes garantizando unas buenas propiedades mecánicas. Sin embargo, este sistema de fabricación conlleva tiempos de producción largos y grandes inversiones en equipamiento lo que restringe su aplicación a otros sectores alejados del sector aeronáutico. Este hecho ha generado una creciente demanda de sistemas de fabricación alternativos al autoclave. Aunque estos sistemas son capaces de reducir los tiempos de producción y el gasto energético, por lo general, dan lugar a materiales con menores prestaciones mecánicas debido a que se reduce la compactación del material al aplicar presiones mas bajas y, por tanto, la fracción volumétrica de fibras, y disminuye el control de la porosidad durante el proceso. Los modelos numéricos existentes permiten conocer los fundamentos de los mecanismos de crecimiento de poros durante la fabricación de materiales compuestos de matriz polimérica mediante autoclave. Dichos modelos analizan el comportamiento de pequeños poros esféricos embebidos en una resina viscosa. Su validez no ha sido probada, sin embargo, para la morfología típica observada en materiales compuestos fabricados fuera de autoclave, consistente en poros cilíndricos y alargados embebidos en resina y rodeados de fibras continuas. Por otro lado, aunque existe una clara evidencia experimental del efecto pernicioso de la porosidad en las prestaciones mecánicas de los materiales compuestos, no existe información detallada sobre la influencia de las condiciones de procesado en la forma, fracción volumétrica y distribución espacial de los poros en los materiales compuestos. Las técnicas de análisis convencionales para la caracterización microestructural de los materiales compuestos proporcionan información en dos dimensiones (2D) (microscopía óptica y electrónica, radiografía de rayos X, ultrasonidos, emisión acústica) y sólo algunas son adecuadas para el análisis de la porosidad. En esta tesis, se ha analizado el efecto de ciclo de curado en el desarrollo de los poros durante la consolidación de preimpregnados Hexply AS4/8552 a bajas presiones mediante moldeo por compresión, en paneles unidireccionales y multiaxiales utilizando tres ciclos de curado diferentes. Dichos ciclos fueron cuidadosamente diseñados de acuerdo a la caracterización térmica y reológica de los preimpregnados. La fracción volumétrica de poros, su forma y distribución espacial se analizaron en detalle mediante tomografía de rayos X. Esta técnica no destructiva ha demostrado su capacidad para analizar la microestructura de materiales compuestos. Se observó, que la porosidad depende en gran medida de la evolución de la viscosidad dinámica a lo largo del ciclo y que la mayoría de la porosidad inicial procedía del aire atrapado durante el apilamiento de las láminas de preimpregnado. En el caso de los laminados multiaxiales, la porosidad también se vio afectada por la secuencia de apilamiento. En general, los poros tenían forma cilíndrica y se estaban orientados en la dirección de las fibras. Además, la proyección de la población de poros a lo largo de la dirección de la fibra reveló la existencia de una estructura celular de un diámetro aproximado de 1 mm. Las paredes de las celdas correspondían con regiones con mayor densidad de fibra mientras que los poros se concentraban en el interior de las celdas. Esta distribución de la porosidad es el resultado de una consolidación no homogenea. Toda esta información es crítica a la hora de optimizar las condiciones de procesado y proporcionar datos de partida para desarrollar herramientas de simulación de los procesos de fabricación de materiales compuestos fuera de autoclave. Adicionalmente, se determinaron ciertas propiedades mecánicas dependientes de la matriz termoestable con objeto de establecer la relación entre condiciones de procesado y las prestaciones mecánicas. En el caso de los laminados unidireccionales, la resistencia interlaminar depende de la porosidad para fracciones volumétricas de poros superiores 1%. Las mismas tendencias se observaron en el caso de GIIc mientras GIc no se vio afectada por la porosidad. En el caso de los laminados multiaxiales se evaluó la influencia de la porosidad en la resistencia a compresión, la resistencia a impacto a baja velocidad y la resistencia a copresión después de impacto. La resistencia a compresión se redujo con el contenido en poros, pero éste no influyó significativamente en la resistencia a compresión despues de impacto ya que quedó enmascarada por otros factores como la secuencia de apilamiento o la magnitud del daño generado tras el impacto. Finalmente, el efecto de las condiciones de fabricación en el proceso de compactación mediante moldeo por compresión en laminados unidireccionales fue simulado mediante el método de los elementos finitos en una primera aproximación para simular la fabricación de materiales compuestos fuera de autoclave. Los parámetros del modelo se obtuvieron mediante experimentos térmicos y reológicos del preimpregnado Hexply AS4/8552. Los resultados obtenidos en la predicción de la reducción de espesor durante el proceso de consolidación concordaron razonablemente con los resultados experimentales. Manufacturing of high performance polymer-matrix composites is normally carried out by means of autoclave using prepreg tapes stacked and consolidated under the simultaneous application of pressure and temperature. High autoclave pressures reduce the porosity in the laminate and ensure excellent mechanical properties. However, this manufacturing route is expensive in terms of capital investment and processing time, hindering its application in many industrial sectors. This fact has driven the demand of alternative out-of-autoclave processing routes. These techniques claim to produce composite parts faster and at lower cost but the mechanical performance is also reduced due to the lower fiber content and to the higher porosity. Corrient numerical models are able to simulate the mechanisms of void growth in polymer-matrix composites processed in autoclave. However these models are restricted to small spherical voids surrounded by a viscous resin. Their validity is not proved for long cylindrical voids in a viscous matrix surrounded by aligned fibers, the standard morphology observed in out-of-autoclave composites. In addition, there is an experimental evidence of the detrimental effect of voids on the mechanical performance of composites but, there is detailed information regarding the influence of curing conditions on the actual volume fraction, shape and spatial distribution of voids within the laminate. The standard techniques of microstructural characterization of composites (optical or electron microscopy, X-ray radiography, ultrasonics) provide information in two dimensions and are not always suitable to determine the porosity or void population. Moreover, they can not provide 3D information. The effect of curing cycle on the development of voids during consolidation of AS4/8552 prepregs at low pressure by compression molding was studied in unidirectional and multiaxial panels. They were manufactured using three different curing cycles carefully designed following the rheological and thermal analysis of the raw prepregs. The void volume fraction, shape and spatial distribution were analyzed in detail by means of X-ray computed microtomography, which has demonstrated its potential for analyzing the microstructural features of composites. It was demonstrated that the final void volume fraction depended on the evolution of the dynamic viscosity throughout the cycle. Most of the initial voids were the result of air entrapment and wrinkles created during lay-up. Differences in the final void volume fraction depended on the processing conditions for unidirectional and multiaxial panels. Voids were rod-like shaped and were oriented parallel to the fibers and concentrated in channels along the fiber orientation. X-ray computer tomography analysis of voids along the fiber direction showed a cellular structure with an approximate cell diameter of 1 mm. The cell walls were fiber-rich regions and porosity was localized at the center of the cells. This porosity distribution within the laminate was the result of inhomogeneous consolidation. This information is critical to optimize processing parameters and to provide inputs for virtual testing and virtual processing tools. In addition, the matrix-controlled mechanical properties of the panels were measured in order to establish the relationship between processing conditions and mechanical performance. The interlaminar shear strength (ILSS) and the interlaminar toughness (GIc and GIIc) were selected to evaluate the effect of porosity on the mechanical performance of unidirectional panels. The ILSS was strongly affected by the porosity when the void contents was higher than 1%. The same trends were observed in the case of GIIc while GIc was insensitive to the void volume fraction. Additionally, the mechanical performance of multiaxial panels in compression, low velocity impact and compression after impact (CAI) was measured to address the effect of processing conditions. The compressive strength decreased with porosity and ply-clustering. However, the porosity did not influence the impact resistance and the coompression after impact strength because the effect of porosity was masked by other factors as the damage due to impact or the laminate lay-up. Finally, the effect of the processing conditions on the compaction behavior of unidirectional AS4/8552 panels manufactured by compression moulding was simulated using the finite element method, as a first approximation to more complex and accurate models for out-of autoclave curing and consolidation of composite laminates. The model parameters were obtained from rheological and thermo-mechanical experiments carried out in raw prepreg samples. The predictions of the thickness change during consolidation were in reasonable agreement with the experimental results.

Valorización de subproductos agrícolas y forestales como sustratos de cultivo en el estado de Oaxaca (México)

El presente trabajo aborda el aprovechamiento de algunos subproductos agrícolas (bagazo de maguey y fibra de coco) y forestales (corteza de pino) en el Estado de Oaxaca (Sur de México). El objetivo principal se centra en localizar, cuantificar y caracterizar estos con vistas a su aplicación como sustratos o componentes de sustratos en cultivos ornamentales, forestales y hortícolas, y a su uso como enmiendas en cultivos tipo. Así mismo se persigue reducir el uso de la turba y la tierra de monte como sustratos mayoritarios en la actualidad. Para la localización de los subproductos se utilizaron los datos de los registros parcelarios de los productores de coco para la obtención de copra (generadores de fibra de coco) de la región costa y de los productores de mezcal (generadores del residuo de bagazo de maguey) de la región valles centrales, así como las ubicaciones de los aserraderos forestales en el Estado de Oaxaca. Se emplea un Sistema de Información Geográfica (SIG) con una cartografía digitalizada de los elementos del medio (clima, geología y suelo), de los cultivos generadores (bagazo de maguey, fibra de coco y corteza de pino), de la agricultura protegida como receptora (tomate) y de la agricultura extensiva con cultivos receptores de enmienda (café, hule, limón, mango, palma de coco y maguey). La producción anual de los residuos se cartografía y cuantifica con los siguientes resultados: bagazo de maguey 624.000 t, fibra de coco 86.000 m3 y 72.000 t de corteza de pino. Mediante el estudio de las características de los suelos de los cultivos receptores y de los requerimientos de materia orgánica de cada cultivo se calcularon las necesidades totales de materia orgánica para cada suelo. Los resultados de las cantidades globales para cada cultivo en todo el Estado muestran una necesidad total de 3.112.000 t de materia orgánica como enmienda. Con los datos obtenidos y a través de un algoritmo matemático se realiza una propuesta de localización de dos plantas de compostaje (de bagazo de maguey y fibra de coco) y cuatro plantas de compostaje de corteza de pino. Con el fin de conocer los subproductos a valorizar como sustrato o componente de sustrato se caracteriza su composición física‐química, siguiendo Normas UNE‐EN, y se analizan mediante Resonancia Magnética Nuclear (RMN). Para el acondicionamiento de bagazo de maguey y la corteza de pino se realizaron ensayos de compostaje. Al final de 241 días la temperatura y la humedad de ambos procesos se encontraban en los rangos recomendados, indicando que los materiales estaban estabilizados y con calidad para ser utilizados como sustrato o componente de sustrato. Para la fibra de coco se realizó el proceso de molienda en seco de conchas de coco provenientes de la comunidad de Río Grande Oaxaca (Principal zona productora de copra en Oaxaca). Posteriormente se emplean los materiales obtenidos como componentes para sustratos de cultivo. Se estudia el compost de bagazo de maguey y siete mezclas; el compost de corteza de pino y ocho mezclas y la fibra de coco con tres mezclas. Estos sustratos alternativos permiten obtener mezclas y reducir el uso de la tierra de monte, turba, arcilla expandida y vermiculita, siendo por tanto una alternativa sostenible para la producción en invernadero. Se elaboraron mezclas especificas para el cultivo de Lilium hibrido asiático y oriental (siete mezclas), sustratos eco‐compatibles para cultivo de tomate (nueve mezclas), para la producción de planta forestal (siete mezclas) y para la producción de plántula hortícola (ocho mezclas). Como resultados más destacados del bagazo de maguey, corteza de pino y las mezclas obtenidas se resume lo siguiente: el bagazo de maguey, con volúmenes crecientes de turba (20, 30, 50 y 60 %) y la corteza de pino, con volúmenes de turba 40 y 60%, presentan valores muy recomendados de porosidad, capacidad de aireación, capacidad de retención de humedad y equilibrio agua‐aire. Para la fibra de coco, la procedente de Río Grande presenta mejor valoración que la muestra comercial de fibra de coco de Morelos. Por último se llevó a cabo la evaluación agronómica de los sustratos‐mezclas, realizando cinco experimentos por separado, estudiando el desarrollo vegetal de cultivos tipo, que se concretan en los siguientes ensayos: 1. Producción de Lilium asiático y oriental en cama para flor de corte; 2. Producción de Lilium oriental en contenedor para flor de corte; 3. Producción de plántula forestal (Pinus greggii E y Pinus oaxacana M); 4. Producción de tomate (Solanum lycopersicum L) y 5. Producción de plántula de tomate en semillero (Solanum lycopersicum L). En relación a la producción de Lilium hibrido asiático en cama los sustratos corteza de pino (CPTU 80:20 v/v), corteza de pino + sustrato comercial (CPSC 80:20 v/v) y corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV2 30:40:15:15 v/v) presentan los mejores resultados. Dichos sustratos también presentan adecuados resultados para Lilium hibrido oriental con excepción de la corteza de pino + turba (CPTU 80:20 v/v). En la producción de Lilium hibrido oriental en contenedor para flor de corte, además de los sustratos de CPSC y CPTAEV2, la mezcla de corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV 70:20:5:5 v/v) manifestó una respuesta favorable. En el ensayo de producción de plántulas de Pinus greggii E y Pinus oaxacana Mirov, las mezclas con corteza de pino+turba+arcilla expandida+vermiculita (CPTAEV2 30:40:15:15 v/v) y bagazo de maguey turba+arcilla expandida+vermiculita (BMTAEV2 30:60:5:5 v/v) son una alternativa que permite disminuir el empleo de turba, arcilla expandida y vermiculita, en comparación con el sustrato testigo de turba+arcilla expandida+vermiculita (TAEV 60:30:10 v/v). En la producción de tomate (Solanum lycopersicum L) frente a la utilización actual del serrín sin compostar (SSC), las mezclas alternativas de bagazo de maguey+turba (BMT 70:30 v/v), fibra de coco de Río Grande (FCRG 100v/v) y corteza de pino+turba (CPT 70:30 v/v), presentaron los mejores resultados en rendimientos. Así mismo, en la producción de plántulas de tomate las dos mezclas alternativas de bagazo de maguey+turba+ arcilla expandida+vermiculita (BMTAEV5 50:30:10:10 v/v) y (BMTAEV6 40:40:10:10 v/v) presentaron mejores resultados que los obtenidos en la mezcla comercial (Sunshine 3), mayoritariamente utilizada en México en la producción de plántula de tomate y hortícola. ABSTRACT This paper addresses the use of some agricultural products (maguey bagasse and coconut fiber) and forestry (pine bark) in the State of Oaxaca (southern Mexico). The principal purpose is to locate, quantify and characterize these with the idea of applying them as substrates or substrate components in ornamental crops, forestry, horticultural, and their use as crop amendments. On the other hand, the reduction of peat and forest soil as main substrates is pursued. For the location of the products, registry parcel data from copra producers (coconut fiber generators) of the coastal region and mescal producers (maguey bagasse residue generators) of the central valleys region, as well as the locations of forest mills in the State of Oaxaca. A Geographic Information System (GIS) with digital mapping of environmental factors (climate, geology and soil), crop generators of residues (maguey bagasse, coconut and pine bark) receptors of amendments such as protected agriculture (tomato) and extensive agriculture crops (coffee, rubber, lemon, mango, coconut and agave). The annual production of waste is mapped and quantified with the following results: 624,000t maguey bagasse, coconut fiber 72,000 m3 and 86,000 t of pine bark. Through the study of receiving crops soils properties of and organic matter requirements of each crop, total needs of organic matter for each soil were estimated. The results of the total quantities for each crop across the state show a total of 3,112,000 t of organic matter needed as amendment. Using that data and a mathematical algorithm, the location of two composting plants (agave bagasse and coconut fiber) and four composting plants pine bark was proposed. In order to know the by‐products that were going to be used as substrates or substrate components, their physical‐chemical composition was analyzed following UNE‐EN technics. Furthermore they were analyzed by Nuclear Magnetic Resonance (NMR). For conditioning of maguey bagasse and pine bark, composting essays were conducted. At the end of 241 days the temperature and humidity of both processes were at the recommended ranges, indicating that the materials were stabilized and had reached the quality to be used as a substrate or substrate component. Coconut shells from the community of Rio Grande Oaxaca (Main copra producing area in Oaxaca) were put through a process of dry milling. Subsequently, the obtained materials were used as components for growing media. We studied the maguey bagasse compost and seven mixtures; the pine bark compost and eight blends and coconut fiber with three mixtures. These alternative substrates allow obtaining mixtures and reduce the use of forest soil, peat, vermiculite and expanded clay, making it a sustainable alternative for greenhouse production. Specific mixtures were prepared for growing Lillium, Asian and eastern hybrids (seven blends), eco‐compatible substrates for tomato (nine mixtures), for producing forest plant (seven mixtures) and for the production of horticultural seedlings (eight mixtures). Results from maguey bagasse, pine bark and mixtures obtained are summarized as follows: the maguey bagasse, with increasing volumes of peat (20, 30, 50 and 60%) and pine bark mixed with 40 and 60% peat by volume, have very recommended values of porosity, aeration capacity, water retention capacity and water‐air balance. Coconut fiber from Rio Grande had better quality than commercial coconut fiber from Morelos. Finally the agronomic evaluation of substrates‐mixtures was carried out conducting five experiments separately: 1. Production of Asiatic and Eastern Lilium in bed for cut flower, 2. Production of oriental Lillium in container for cut flower, 3.Production of forest seedlings (Pinus greggii E and Pinus oaxacana M), 4. Production of tomato (Solanum lycopersicum L) and 5. Tomato seedling production in seedbed (Solanum lycopersicum L). In relation to the production of hybrid Asian Lilium in bed, pine bark substrates (CPTU 80:20 v/v), pine bark + commercial substrate (CPSC 80:20 v/v) and pine bark + peat + expanded clay + vermiculite (CPTAEV2 30:40:15:15 v/v) showed the best results. Such substrates also have adequate results for Lilium Oriental hybrid except pine bark + peat (CPTU 80:20 v / v). In the production of Lilium oriental hybrid container for cut flower, besides the CPSC and CPTAEV2 substrates, the mixture of pine bark + peat + vermiculite expanded clay (CPTAEV 70:20:5:5 v / v) showed a favorable response. In the production of Pinus greggii E and Pinus oaxacana Mirov seedlings trial, mixtures with pine bark + peat + expanded clay + vermiculite (CPTAEV2 30:40:15:15 v/v) and maguey bagasse+ peat+ expanded clay + vermiculite (BMTAEV2 30:60:5:5 v / v) are an alternative which allows reducing the use of peat, vermiculite and expanded clay in comparison with the control substrate made of peat + expanded clay+ vermiculite (60:30 TAEV: 10 v/v). In the production of tomato (Solanum lycopersicum L), alternative mixes of maguey bagasse + peat (BMT 70:30 v/v), coconut fiber from Rio Grande (FCRG 100 v / v) and pine bark + peat (CPT 70:30 v / v) showed the best results in yields versus the current use of sawdust without compost (SSC). Likewise, in the production of tomato seedlings of the two alternative mixtures maguey bagasse + peat expanded clay + vermiculite (BMTAEV5 50:30:10:10 v/v) and (BMTAEV6 40:40:10:10 v/v) had better results than those obtained in the commercial mixture (Sunshine 3), mainly used in Mexico in tomato seedling production and horticulture.

One-watt fiber-based power-by-light system for satellite applications

In this work, a fiber-based optical powering (or power-by-light) system capable of providing more than 1 W is developed. The prototype was used in order to power a shunt regulator for controlling the activation and deactivation of solar panels in satellites. The work involves the manufacture of a light receiver (a GaAs multiple photovoltaic converter (MPC)), a power conditioning block, and a regulator and the implementation and characterization of the whole system. The MPC, with an active area of just 3.1 mm2, was able to supply 1 W at 5 V with an efficiency of 30%. The maximum measured device efficiency was over 40% at an input power (Pin) of 0.5 W. Open circuit voltage over 7 V was measured for Pin over 0.5 W. A system optoelectronic efficiency (including the optical fiber, connectors, and MPC) of 27% was measured at an output power (Pout) of 1 W. At Pout = 0.2 W, the efficiency was as high as 36%. The power conditioning block and the regulator were successfully powered with the system. The maximum supplied power in steady state was 0.2 W, whereas in transient state, it reached 0.44 W. The paper also describes the characterization of the system within the temperature range going from -70 to +100?°C.

Intraply fracture of fiber-reinforced composites: microscopic mechanisms and modeling

The fracture behavior parallel to the fibers of an E-glass/epoxy unidirectional laminate was studied by means of three-point tests on notched beams. Selected tests were carried out within a scanning electron microscope to ascertain the damage and fracture micromechanisms upon loading. The mechanical behavior of the notched beam was simulated within the framework of the embedded cell model, in which the actual composite microstructure was resolved in front of the notch tip. In addition, matrix and interface properties were independently measured in situ using a nanoindentor. The numerical simulations very accurately predicted the macroscopic response of the composite as well as the damage development and crack growth in front of the notch tip, demonstrating the ability of the embedded cell approach to simulate the fracture behavior of heterogeneous materials. Finally, this methodology was exploited to ascertain the influence of matrix and interface properties on the intraply toughness.

Damage localization and failure locus under biaxial loading in glass-fiber nonwoven felts

The pattern of damage localization and fracture under uniaxial and biaxial tension was studied in glass–fiber nonwoven felts. The analyses were carried out within the framework of the finite-element simulation of plain and notched specimens in which the microstructure of the felt, made up of fiber bundles connected at the cross point through an organic binder, was explicitly represented. Following previous experimental observations, fracture by interbundle decohesion and energy dissipation by frictional sliding between the bundles were included in the model. It was found that the failure path in these materials was controlled by the maximum applied normal stress, regardless of the loading path, and that the failure locus under biaxial tension was well represented by the von Mises failure criteria. The notch sensitivity of the nonwoven felts was limited and the presence of a notch did not modify the failure path.

A methodology to measure the interface shear strength by means of the fiber push-in test

A methodology is presented to measure the fiber/matrix interface shear strength in composites. The strategy is based on performing a fiber push-in test at the central fiber of highly-packed fiber clusters with hexagonal symmetry which are often found in unidirectional composites with a high volume fraction of fibers. The mechanics of this test was analyzed in detail by means of three-dimensional finite element simulations. In particular, the influence of different parameters (interface shear strength, toughness and friction as well as fiber longitudinal elastic modulus and curing stresses) on the critical load at the onset of debonding was established. From the results of the numerical simulations, a simple relationship between the critical load and the interface shear strength is proposed. The methodology was validated in an unidirectional C/epoxy composite and the advantages and limitations of the proposed methodology are indicated.

Application of digital image correlation at the microscale in fiber-reinforced composites

Digital image correlation (DIC) is applied to analyzing the deformation mechanisms under transverse compression in a fiber-reinforced composite. To this end, compression tests in a direction perpendicular to the fibers were carried out inside a scanning electron microscope and secondary electron images obtained at different magnifications during the test. Optimum DIC parameters to resolve the displacement and strain field were computed from numerical simulations of a model composite and they were applied to micrographs obtained at different magnifications (250_, 2000_, and 6000_). It is shown that DIC of low-magnification micrographs was able to capture the long range fluctuations in strain due to the presence of matrix-rich and fiber-rich zones, responsible for the onset of damage. At higher magnification, the strain fields obtained with DIC qualitatively reproduce the non-homogeneous deformation pattern due to the presence of stiff fibers dispersed in a compliant matrix and provide accurate results of the average composite strain. However, comparison with finite element simulations revealed that DIC was not able to accurately capture the average strain in each phase.

Tuning the properties of carbon fiber-reinforced poly (phenylene sulphide) laminates via incorporation of inorganic fullerene-like WS2 nanoparticles

Novel carbon fiber (CF)-reinforced poly(phenylene sulphide) (PPS) laminates incorporating inorganic fullerene-like tungsten disulfide (IF-WS2) nanoparticles were prepared via melt-blending and hot-press processing. The influence of the IF-WS2 on the morphology, thermal, mechanical and tribological properties of PPS/CF composites was investigated. Efficient nanoparticle dispersion within the matrix was attained without using surfactants. A progressive rise in thermal stability was found with increasing IF-WS2 loading, as revealed by thermogravimetric analysis. The addition of low nanoparticle contents retarded the crystallization of the matrix, whereas concentrations equal or higher than 1.0 wt% increased both the crystallization temperature and degree of crystallinity compared to those of PPS/CF. Mechanical tests indicated that with only 1.0 wt% IF-WS2 the flexural modulus and strength of PPS/CF improved by 17 and 14%, respectively, without loss in toughness, ascribed to a synergistic effect between the two fillers. A significant enhancement in the storage modulus and glass transition temperature was also observed. Moreover, the wear rate and coefficient of friction strongly decreased, attributed to the lubricant role of the IF-WS2 combined with their reinforcing effect. These inorganic nanoparticles show great potential to improve the mechanical and tribological properties of conventional thermoplastic/CF composites for structural applications.

Application of active heat pulse method with fiber optic temperature sensing for estimation of wetting bulbs and water distribution in drip emitters.

Through the use of the Distributed Fiber Optic Temperature Measurement (DFOT) method, it is possible to measure the temperature in small intervals (on the order of centimeters) for long distances (on the order of kilometers) with a high temporal frequency and great accuracy. The heat pulse method consists of applying a known amount of heat to the soil and monitoring the temperature evolution, which is primarily dependent on the soil moisture content. The use of both methods, which is called the active heat pulse method with fiber optic temperature sensing (AHFO), allows accurate soil moisture content measurements. In order to experimentally study the wetting patterns, i.e. shape, size, and the water distribution, from a drip irrigation emitter, a soil column of 0.5 m of diameter and 0.6 m high was built. Inside the column, a fiber optic cable with a stainless steel sheath was placed forming three concentric helixes of diameters 0.2 m, 0.4 m and 0.6 m, leading to a 148 measurement point network. Before, during, and after the irrigation event, heat pulses were performed supplying electrical power of 20 W/m to the steel. The soil moisture content was measured with a capacitive sensor in one location at depths of 0.1 m, 0.2 m, 0.3 m and 0.4 m during the irrigation. It was also determined by the gravimetric method in several locations and depths before and right after the irrigation. The emitter bulb dimensions and shape evolution was satisfactorily measured during infiltration. Furthermore, some bulb's characteristics difficult to predict (e.g. preferential flow) were detected. The results point out that the AHFO is a useful tool to estimate the wetting pattern of drip irrigation emitters in soil columns and show a high potential for its use in the field.

Biokerosene from coconut, babassu, camelina and palm kernel oils: production and properties of their blends with fossil kerosene

On December 20th 2006 the European Commission approved a law proposal to include the civil aviation sector in the European market of carbon dioxide emission rights [European Union Emissions Trading System, EUETS). On July 8th 2009, the European Parliament and Conseil agreed that all flights leaving or landing in the EU airports starting from January 1st 2012 should be included in the EUETS. On November 19th 2008, the EU Directive 2008/101/CE [1] included the civil aviation activities in the EUETS, and this directive was transposed by the Spanish law 13/2010 of July 5th 2010 [2]. Thus, in 2012 the aviation sector should reduce their emissions to 97 % of the mean values registered in the period 2004-2006, and for 2013 these emission reductions should reach 95 % of the mean values for that same period. Trying to face this situation, the aviation companies are planning seriously the use of alternative jet fuels to reduce their greenhouse gas emissions and to lower their costs. However, some US airlines have issued a lawsuit before the European Court of Justice based in that this EU action violates a long standing worldwide aviation treaty, the Chicago convention of 1944, and also the Chinese aviation companies have rejected to pay any EU carbon dioxide tax [3]. Moreover, the USA Departments of Agriculture and Energy and the Navy will invest a total of up to $150 million over three years to spur production of aviation and marine biofuels for commercial and military applications [4]. However, the jet fuels should fulfill a set of extraordinarily sensitive properties to guarantee the safety of planes and passengers during all the flights.