Wireless Sensor Network based on OCDMA for closed environments

An infrared optical wireless system is presented, consisting on autonomous remote nodes communicating with a central node. The network is designed for telecommand/telemetry purposes, comprising a large number of nodes at a low data rate. Simultaneous access is granted by using CDMA techniques, and an appropriate selection of the code family can also keep power consumption to a minimum

Experiences on using closed-loop control systems for smoke control

The main objective of ventilation systems in case of fire is the reduction of the possible consequences by achieving the best possible conditions for the evacuation of the users and the intervention of the emergency services. In the last years, the required quick response of the ventilation system, from normal to emergency mode, has been improved by the use of automatic and semi-automatic control systems, what reduces the response times through the support to the operators decision taking, and the use of pre-defined strategies. A further step consists on the use of closedloop algorithms, which takes into account not only the initial conditions but their development (air velocity, traffic situation, etc), optimizing the quality of the smoke control process

Structural health monitoring network system with wireless communications inside closed aerospace structures

Structural Health Monitoring (SHM) requires integrated "all in one" electronic devices capable of performing analysis of structural integrity and on-board damage detection in aircraft?s structures. PAMELA III (Phased Array Monitoring for Enhanced Life Assessment, version III) SHM embedded system is an example of this device type. This equipment is capable of generating excitation signals to be applied to an array of integrated piezoelectric Phased Array (PhA) transducers stuck to aircraft structure, acquiring the response signals, and carrying out the advanced signal processing to obtain SHM maps. PAMELA III is connected with a host computer in order to receive the configuration parameters and sending the obtained SHM maps, alarms and so on. This host can communicate with PAMELA III through an Ethernet interface. To avoid the use of wires where necessary, it is possible to add Wi-Fi capabilities to PAMELA III, connecting a Wi-Fi node working as a bridge, and to establish a wireless communication between PAMELA III and the host. However, in a real aircraft scenario, several PAMELA III devices must work together inside closed structures. In this situation, it is not possible for all PAMELA III devices to establish a wireless communication directly with the host, due to the signal attenuation caused by the different obstacles of the aircraft structure. To provide communication among all PAMELA III devices and the host, a wireless mesh network (WMN) system has been implemented inside a closed aluminum wingbox. In a WMN, as long as a node is connected to at least one other node, it will have full connectivity to the entire network because each mesh node forwards packets to other nodes in the network as required. Mesh protocols automatically determine the best route through the network and can dynamically reconfigure the network if a link drops out. The advantages and disadvantages on the use of a wireless mesh network system inside closed aerospace structures are discussed.

The role of the urban support in the regeneration of vulnerable neighbourhoods

The processes of social and urban segregation have got worse during the last decades. Several studies have deepened into the analysis of the causes and consequences of these processes and have tried to define solutions that beyond eradicating some specific problems, were aimed at the consolidation of sustainable urban environments. This paper presents an approach to the problem of urban inequality based on the concept of urban vulnerability as something that goes beyond the social and economic problems. In exclusion processes it is very important to consider the urban context and the physical and structural conditions not only in each neighborhood but also in the city as a whole. The paper seeks to pose a reflection on the urban support, which is understood in all its complexity and thought to be a key to ensure access and the right to the city of the citizens most in need.

Personalized rule-based closed-loop control algorithm for type 1 diabetes

Type 1 diabetes-mellitus implies a life-threatening absolute insulin deficiency. Artificial pancreas (CGM sensor, insulin pump and control algorithm) is promising to outperform current open-loop therapies.

On the role of global flow instability analysis in closed loop flow control

Control of linear flow instabilities has been demonstrated to be an effective theoretical flow control methodology, capable of modifying transitional flows on canonical geometries such as the plane channel and the flat-plate boundary layer. Extending the well-developed theoretical flow control techniques to flows over or through complex geometries requires addressing the issue of efficient capturing of the leading members of the global eigenspectrum pertinent to such flows. The present contribution describes state-of-the-art modal global instability analysis methodologies recently developed in our group, based on matrix formation and time-stepping, respectively. The relative performance of these algorithms is assessed on the recovery of BiGlobal and TriGlobal eigenspectra in the spanwise periodic and the cubic lid-driven cavity, respectively; the adjoint eigenspectrum in the latter flow is recovered for the first time. For three-dimensional flows without any homogeneous spatial direction, the time-stepping methodology was found to outperform the matrix-forming approach and permit recovering the leading TriGlobal eigenmodes in an three-dimensional open cavity of aspect ratio L : D : W = 5 : 1 : 1; theoretical flow control of this configuration is underway.

On the role of global flow instability analysis in closed loop flow control

Control of linear flow instabilities has been demonstrated to be an effective theoretical flow control methodology, capable of modifying transitional flow on canonical geometries such as the plane channel and the flat-plate boundary layer.

A management model for closed-loop supply chains of reusable articles

This PhD dissertation is framed in the emergent fields of Reverse Logistics and ClosedLoop Supply Chain (CLSC) management. This subarea of supply chain management has gained researchers and practitioners' attention over the last 15 years to become a fully recognized subdiscipline of the Operations Management field. More specifically, among all the activities that are included within the CLSC area, the focus of this dissertation is centered in direct reuse aspects. The main contribution of this dissertation to current knowledge is twofold. First, a framework for the so-called reuse CLSC is developed. This conceptual model is grounded in a set of six case studies conducted by the author in real industrial settings. The model has also been contrasted with existing literature and with academic and professional experts on the topic as well. The framework encompasses four building blocks. In the first block, a typology for reusable articles is put forward, distinguishing between Returnable Transport Items (RTI), Reusable Packaging Materials (RPM), and Reusable Products (RP). In the second block, the common characteristics that render reuse CLSC difficult to manage from a logistical standpoint are identified, namely: fleet shrinkage, significant investment and limited visibility. In the third block, the main problems arising in the management of reuse CLSC are analyzed, such as: (1) define fleet size dimension, (2) control cycle time and promote articles rotation, (3) control return rate and prevent shrinkage, (4) define purchase policies for new articles, (5) plan and control reconditioning activities, and (6) balance inventory between depots. Finally, in the fourth block some solutions to those issues are developed. Firstly, problems (2) and (3) are addressed through the comparative analysis of alternative strategies for controlling cycle time and return rate. Secondly, a methodology for calculating the required fleet size is elaborated (problem (1)). This methodology is valid for different configurations of the physical flows in the reuse CLSC. Likewise, some directions are pointed out for further development of a similar method for defining purchase policies for new articles (problem (4)). The second main contribution of this dissertation is embedded in the solutions part (block 4) of the conceptual framework and comprises a two-level decision problem integrating two mixed integer linear programming (MILP) models that have been formulated and solved to optimality using AIMMS as modeling language, CPLEX as solver and Excel spreadsheet for data introduction and output presentation. The results obtained are analyzed in order to measure in a client-supplier system the economic impact of two alternative control strategies (recovery policies) in the context of reuse. In addition, the models support decision-making regarding the selection of the appropriate recovery policy against the characteristics of demand pattern and the structure of the relevant costs in the system. The triangulation of methods used in this thesis has enabled to address the same research topic with different approaches and thus, the robustness of the results obtained is strengthened.

An ICT-based closed-loop model to improve care for heart failure patients

Durante las últimas décadas se ha producido un fenómeno global de envejecimiento en la población. Esta tendencia se puede observar prácticamente en todos los países del mundo y se debe principalmente a los avances en la medicina, y a los descensos en las tasas de fertilidad y mortalidad. El envejecimiento de la población tiene un gran impacto en la salud de los ciudadanos, y a menudo es la causa de aparición de enfermedades crónicas. Este tipo de enfermedades supone una amenaza y una carga importantes para la sociedad, especialmente en aspectos como la mortalidad o los gastos en los sistemas sanitarios. Entre las enfermedades cardiovasculares, la insuficiencia cardíaca es probablemente la condición con mayor prevalencia y afecta a 23-26 millones de personas en todo el mundo. Normalmente, la insuficiencia cardíaca presenta un mal pronóstico y una tasa de supervivencia bajas, en algunos casos peores que algún tipo de cáncer. Además, suele ser la causa de hospitalizaciones frecuentes y es una de las enfermedades más costosas para los sistemas sanitarios. La tendencia al envejecimiento de la población y la creciente incidencia de las enfermedades crónicas están llevando a una situación en la que los sistemas de salud no son capaces de hacer frente a la demanda de la sociedad. Los servicios de salud existentes tendrán que adaptarse para ser efectivos y sostenibles en el futuro. Es necesario identificar nuevos paradigmas de cuidado de pacientes, así como mecanismos para la provisión de servicios que ayuden a transformar estos sistemas sanitarios. En este contexto, esta tesis se plantea la búsqueda de soluciones, basadas en las Tecnologías de la Información y la Comunicación (TIC), que contribuyan a realizar la transformación en los sistemas sanitarios. En concreto, la tesis se centra en abordar los problemas de una de las enfermedades con mayor impacto en estos sistemas: la insuficiencia cardíaca. Las siguientes hipótesis constituyen la base para la realización de este trabajo de investigación: 1. Es posible definir un modelo basado en el paradigma de lazo cerrado y herramientas TIC que formalice el diseño de mejores servicios para pacientes con insuficiencia cardíaca. 2. El modelo de lazo cerrado definido se puede utilizar para definir un servicio real que ayude a gestionar la insuficiencia cardíaca crónica. 3. La introducción, la adopción y el uso de un servicio basado en el modelo definido se traducirá en mejoras en el estado de salud de los pacientes que sufren insuficiencia cardíaca. a. La utilización de un sistema basado en el modelo de lazo cerrado definido mejorará la experiencia del usuario de los pacientes. La definición del modelo planteado se ha basado en el estándar ISO / EN 13940- Sistema de conceptos para dar soporte a la continuidad de la asistencia. Comprende un conjunto de conceptos, procesos, flujos de trabajo, y servicios como componentes principales, y representa una formalización de los servicios para los pacientes con insuficiencia cardíaca. Para evaluar el modelo definido se ha definido un servicio real basado en el mismo, además de la implementación de un sistema de apoyo a dicho servicio. El diseño e implementación de dicho sistema se realizó siguiendo la metodología de Diseño Orientado a Objetivos. El objetivo de la evaluación consistía en investigar el efecto que tiene un servicio basado en el modelo de lazo cerrado sobre el estado de salud de los pacientes con insuficiencia cardíaca. La evaluación se realizó en el marco de un estudio clínico observacional. El análisis de los resultados ha comprendido métodos de análisis cuantitativos y cualitativos. El análisis cuantitativo se ha centrado en determinar el estado de salud de los pacientes en base a datos objetivos (obtenidos en pruebas de laboratorio o exámenes médicos). Para realizar este análisis se definieron dos índices específicos: el índice de estabilidad y el índice de la evolución del estado de salud. El análisis cualitativo ha evaluado la autopercepción del estado de salud de los pacientes en términos de calidad de vida, auto-cuidado, el conocimiento, la ansiedad y la depresión, así como niveles de conocimiento. Se ha basado en los datos recogidos mediante varios cuestionarios o instrumentos estándar (i.e. EQ-5D, la Escala de Ansiedad y Depresión (HADS), el Cuestionario de Cardiomiopatía de Kansas City (KCCQ), la Escala Holandesa de Conocimiento de Insuficiencia Cardíaca (DHFKS), y la Escala Europea de Autocuidado en Insuficiencia Cardíaca (EHFScBS), así como cuestionarios dedicados no estandarizados de experiencia de usuario. Los resultados obtenidos en ambos análisis, cuantitativo y cualitativo, se compararon con el fin de evaluar la correlación entre el estado de salud objetivo y subjetivo de los pacientes. Los resultados de la validación demostraron que el modelo propuesto tiene efectos positivos en el cuidado de los pacientes con insuficiencia cardíaca y contribuye a mejorar su estado de salud. Asimismo, ratificaron al modelo como instrumento válido para la definición de servicios mejorados para la gestión de esta enfermedad. ABSTRACT During the last decades we have witnessed a global aging phenomenon in the population. This can be observed in practically every country in the world, and it is mainly caused by the advances in medicine, and the decrease of mortality and fertility rates. Population aging has an important impact on citizens’ health and it is often the cause for chronic diseases, which constitute global burden and threat to the society in terms of mortality and healthcare expenditure. Among chronic diseases, Chronic Heart Failure (CHF) or Heart Failure (HF) is probably the one with highest prevalence, affecting between 23 and 26 million people worldwide. Heart failure is a chronic, long-term and serious condition with very poor prognosis and worse survival rates than some type of cancers. Additionally, it is often the cause of frequent hospitalizations and one of the most expensive conditions for the healthcare systems. The aging trends in the population and the increasing incidence of chronic diseases are leading to a situation where healthcare systems are not able to cope with the society demand. Current healthcare services will have to be adapted and redefined in order to be effective and sustainable in the future. There is a need to find new paradigms for patients’ care, and to identify new mechanisms for services’ provision that help to transform the healthcare systems. In this context, this thesis aims to explore new solutions, based on ICT, that contribute to achieve the needed transformation within the healthcare systems. In particular, it focuses on addressing the problems of one of the diseases with higher impact within these systems: Heart Failure. The following hypotheses represent the basis to the elaboration of this research: 1. It is possible to define a model based on a closed-loop paradigm and ICT tools that formalises the design of enhanced healthcare services for chronic heart failure patients. 2. The described closed-loop model can be exemplified in a real service that supports the management of chronic heart failure disease. 3. The introduction, adoption and use of a service based on the outlined model will result in improvements in the health status of patients suffering heart failure. 4. The user experience of patients when utilizing a system based on the defined closed-loop model will be enhanced. The definition of the closed-loop model for health care support of heart failure patients have been based on the standard ISO/EN 13940 System of concepts to support continuity of care. It includes a set of concept, processes and workflows, and services as main components, and it represent a formalization of services for heart failure patients. In order to be validated, the proposed closed-loop model has been instantiated into a real service and a supporting IT system. The design and implementation of the system followed the user centred design methodology Goal Oriented Design. The validation, that included an observational clinical study, aimed to investigate the effect that a service based on the closed-loop model had on heart failure patients’ health status. The analysis of results comprised quantitative and qualitative analysis methods. The quantitative analysis was focused on determining the health status of patients based on objective data (obtained in lab tests or physical examinations). Two specific indexes where defined and considered in this analysis: the stability index and the health status evolution index. The qualitative analysis assessed the self-perception of patients’ health status in terms of quality of life, self-care, knowledge, anxiety and depression, as well as knowledge levels. It was based on the data gathered through several standard instruments (i.e. EQ-5D, the Hospital Anxiety and Depression Scale, the Kansas City Cardiomyopathy Questionnaire, the Dutch Heart Failure Knowledge Scale, and the European Heart Failure Self-care Behaviour Scale) as well as dedicated non-standardized user experience questionnaires. The results obtained in both analyses, quantitative and qualitative, were compared in order to assess the correlation between the objective and subjective health status of patients. The results of the validation showed that the proposed model contributed to improve the health status of the patients and had a positive effect on the patients’ care. It also proved that the model is a valid instrument for designing enhanced healthcare services for heart failure patients.

La participación de los jóvenes universitarios en la planificación urbana. Estudios de caso de Lisboa, Madrid y Fortaleza

La participación de los jóvenes en los procesos de planificación urbana en Lisboa, Madrid y Fortaleza ha sido tema central de la presente tesis. Los principales objetivos perseguidos consisten en: caracterizar y analizar críticamente las dimensiones más importantes de la participación de jóvenes universitarios en los procesos participativos; aportar características de interés juvenil para un “modelo” de planificación urbana; elaborar directrices para el diseño de actuaciones en un proceso urbano participativo desde la perspectiva de los jóvenes; establecer el alcance de un instrumento urbano participativo reglamentado por el gobierno local entre los jóvenes; determinar si la percepción de los jóvenes universitarios acerca de las acciones del gobierno local tiene influencia en los procesos participativos. El universo estadístico de la muestra lo conforman la totalidad de 737 jóvenes universitarios encuestados en Lisboa, Madrid y Fortaleza. Que se distribuye en 104 encuestados en Lisboa, 329 en Madrid, y 304 en la ciudad de Fortaleza. El cuestionario contiene preguntas: abiertas, cerradas y mixtas. La mayor parte de las cuestiones son cerradas, y en cuanto a las opciones de respuesta: en muchas preguntas se ha aplicado, una escala tipo Likert, entre 1 y 4, siendo 4 el grado más alto (totalmente de acuerdo), y 1 el grado más bajo (nada de acuerdo), y para otras, una opción múltiple, con solamente una opción de respuesta. Se realizó un cuestionario de 31 preguntas en Lisboa, y tras su aplicación y obtención de resultados se revisó y mejoró obteniendo un cuestionario de 23 preguntas que fue aplicado en Madrid y Fortaleza. Se realizan análisis descriptivos, y algún análisis factorial en diversas preguntas del cuestionario, y se estudian diferencias en función de las variables sociodemográficas planteadas. Los resultados constatan que es muy baja la participación en los procesos institucionalizados por el gobierno local, en contrapartida es bastante alta en los procesos organizados por los ciudadanos. La información limita la participación de los jóvenes y ya que estos reconocen como motivación estar más y mejor informados y controlar y acompañar las acciones de su gobierno local. Por otra parte, desean participar en grupo en foros y debates presenciales. Los jóvenes madrileños consideran que las etapas más importantes en un proceso urbano participativo son: información, seguimiento y evaluación, mientras que para los jóvenes de Fortaleza son: Fiscalización, concienciación e información. Se ha verificado que desde la percepción de los jóvenes de Lisboa los ciudadanos son consultados en los procesos urbanos participativos y de acuerdo con los jóvenes de Madrid y Fortaleza los ciudadanos son dirigidos, influenciados y manipulados. Los problemas de carácter urbano no tienen una conceptualización clara y precisa entre los jóvenes universitarios y los problemas urbanos que más afectan la vida de los jóvenes universitarios son aparcamientos, contaminación y seguridad urbana. Sin embargo, los transportes son apuntados por los jóvenes universitarios de Lisboa, Madrid y Fortaleza. Además no saben identificar los problemas de su barrio. Así como de las causas y consecuencias y soluciones de los problemas urbanos. Eligen como mejor estrategia para desarrollar un proceso urbano participativo el acuerdo entre técnicos, población y el gobierno local. Los jóvenes universitarios de Fortaleza apuntan directrices para una planificación urbana con énfasis en la seguridad urbana, la sostenibilidad y la investigación, tecnología e innovación. Por otro lado, los jóvenes universitarios de Madrid perfilan tres “modelos” de planificación urbana: un “Modelo” socio-económica, un “Modelo” sostenible e innovadora y un “Modelo” de Planificación Urbana con énfasis en espacios públicos, entretenimiento, seguridad urbana y deporte. Los jóvenes universitarios rechazan la idea que la planificación urbana lleva en cuenta sus perspectivas y opiniones. Respeto al Presupuesto Participativo, el alcance de dicho proceso entre los jóvenes universitarios es extremamente bajo. Sin embargo, opinan que la aproximación entre ciudadanos, técnicos y gobierno en los procesos de Presupuesto Participativo mejora la rendición de cuentas. Además los jóvenes creen que dichos procesos conceden un poder moderado a los ciudadanos, y consideran que el poder concedido en los procesos urbanos influye directamente en el interés y empeño en participar. ABSTRACT Youth participation in urban planning processes in Lisbon, Madrid and Fortaleza is the main subject of this thesis. Our key goals are the following: characterising and critically analysing the most important dimensions of young university students’ participation in participative processes; providing features of interest for the young for an urban planning “model”; developing a variety of guidelines for designing actions in a participative urban process from the perspective of young people; analysing the impact upon the young of a participative urban instrument implemented by the local government; determining whether young university students’ perception of local government actions influences participative processes. The statistical universe of the sample comprises a total of 737 young university students who were surveyed in Lisbon, Madrid and Fortaleza, distributed as follows: 104 respondents in Lisbon, 329 in Madrid, and 304 in Fortaleza. The survey is made up of open-ended, closed-ended and mixed questions. Most questions are closed-ended. Regarding the answer options, a Likert-type scale has been used in many questions. The scale ranges from 1 to 4, 4 being the highest value (completely agree) and 1 the lowest (completely disagree). Besides, there are multiple-choice questions with only one possible answer. A 31- question survey was conducted in Lisbon. After the survey was run and the results were obtained, it was reviewed and improved. The improved version was a 23- question survey which was conducted in Madrid and Fortaleza. Descriptive analyses as well as some factorial analyses are carried out in several questions, and differences are studied depending on the socio-demographic variables involved. The results show that participation in processes implemented by local governments is very low. In contrast, participation is quite high in processes organised by citizens. Information limits youth participation, as young people point out that they are motivated by more and better information and by the possibility of monitoring and keeping track of their local government actions. They also wish to take part in face-to-face group forums and discussions. Young people from Madrid think that the most important stages in participative urban processes are information, follow-up and assessment, whereas young people from Fortaleza highlight tax matters, awareness and information. It has been confirmed that Lisbon youth perceive that citizens are consulted in participative urban processes. Youth from Madrid and Fortaleza, on the other hand, state that citizens are directed, influenced and manipulated. Young university students do not have a clear, precise concept of urban problems. Among these, they are most affected by car parks, pollution and urban safety, but the transport problem is pointed out by young university students from Lisbon, Madrid and Fortaleza. Furthermore, they cannot identify the problems in their neighbourhoods, nor are they able to specify the causes, consequences and solutions of urban problems. Their preferred strategy for developing a participative urban process is an agreement between technicians, the population and the local government. Young university students from Fortaleza suggest guidelines for an urban planning approach emphasising urban safety, sustainability and research, technology and innovation. Those from Madrid, for their part, outline three urban planning “models”: a socioeconomic “model”, a sustainable and innovative “model”, and an urban planning “model” with a focus on public areas, entertainment, urban safety and sport. Young university students disagree that urban planning takes their perspectives and views into account. Moreover, the impact of the Participative Budget upon their lives is extremely low. In their opinion, however, closer collaboration between citizens, technicians and governments in Participative Budget processes promotes accountability. The young also think that these processes give moderate power to citizens, and in their view the power that can be exerted in urban processes directly influences the interest in participating and the will to do so.

Some examples of the simultaneous use of closed-form and numerical solutions in shell structural analysis

The computational advantages of the use of different approaches -numerical and analytical ones- to the analysis of different parts of the same shell structure are discussed. Examples of large size problems that can be reduced to those more suitable to be handled by a personal related axisyrometric finite elements, local unaxisymmetric shells, geometric quasi-regular shells, infinite elements and homogenization techniques are described