Assessment of Hydrogen as suistinable clean energy

The progressive depletion of fossil fuels and their high contribution to the energy supply in this modern society forces that will be soon replaced by renewable fuels. But the dispersion and alternation of renewable energy production also undertake to reduce their costs to use as energy storage and hydrogen carrier. It is necessary to develop technologies for hydrogen production from all renewable energy storage technologies and the development of energy production from hydrogen fuel cells and cogeneration and tri generation systems. In order to propel this technological development discussed where the hydrogen plays a key role as energy storage and renewable energy, the National Centre of Hydrogen and Fuel Cell Technology Experimentation in Spain equipped with installations that enable scientific and technological design, develop, verify, certify, approve, test, measure and, more importantly, the facility ensures continuous operation for 24 hours a day, 365 days year. At the same time, the system is scalable so as to allow continuous adaptation of new technologies are developed and incorporated into the assembly to verify integration at the same time it checks the validity of their development. The transformation sector can be said to be the heart of the system, because without neglecting the other sectors, this should prove the validity of hydrogen as a carrier - energy storage are important efforts that have to do to demonstrate the suitability of fuel cells or internal combustion systems to realize the energy stored in hydrogen at prices competitive with conventional systems. The multiple roles to meet the fuel cells under different conditions of operation require to cover their operating conditions, many different sizes and applications. The fourth area focuses on integration is an essential complement within the installation. We must integrate not only the electricity produced, but also hydrogen is used and the heat generated in the process of using hydrogen energy. The energy management in its three forms: hydrogen chemical, electrical and thermal integration requires complicated and require a logic and artificial intelligence extremes to ensure maximum energy efficiency at the same time optimum utilization is achieved. Verification of the development and approval in the entire production system and, ultimately, as a demonstrator set to facilitate the simultaneous evolution of production technology, storage and distribution of hydrogen fuel cells has been assessed.

Clean Coal Technologies Scenario and Evaluation of Present CO2 Dwindling Initiatives to Approach Zero Emission Power Stations By Coal Combustion. Deployment Situation and Evaluation Study

In the present uncertain global context of reaching an equal social stability and steady thriving economy, power demand expected to grow and global electricity generation could nearly double from 2005 to 2030. Fossil fuels will remain a significant contribution on this energy mix up to 2050, with an expected part of around 70% of global and ca. 60% of European electricity generation. Coal will remain a key player. Hence, a direct effect on the considered CO2 emissions business-as-usual scenario is expected, forecasting three times the present CO2 concentration values up to 1,200ppm by the end of this century. Kyoto protocol was the first approach to take global responsibility onto CO2 emissions monitoring and cap targets by 2012 with reference to 1990. Some of principal CO2emitters did not ratify the reduction targets. Although USA and China spur are taking its own actions and parallel reduction measures. More efficient combustion processes comprising less fuel consuming, a significant contribution from the electricity generation sector to a CO2 dwindling concentration levels, might not be sufficient. Carbon Capture and Storage (CCS) technologies have started to gain more importance from the beginning of the decade, with research and funds coming out to drive its come in useful. After first researching projects and initial scale testing, three principal capture processes came out available today with first figures showing up to 90% CO2 removal by its standard applications in coal fired power stations. Regarding last part of CO2 reduction chain, two options could be considered worthy, reusing (EOR & EGR) and storage. The study evaluates the state of the CO2 capture technology development, availability and investment cost of the different technologies, with few operation cost analysis possible at the time. Main findings and the abatement potential for coal applications are presented. DOE, NETL, MIT, European universities and research institutions, key technology enterprises and utilities, and key technology suppliers are the main sources of this study. A vision of the technology deployment is presented.

Organisational learning, strategic rigidity and technology adoption: Implications for electric utilities and renewable energy firms

This paper examines the implications of strategic rigidness for technology adoption behaviours among electric utilities. Such behaviours lead to heterogeneity in firm performance and consequently affect the electric utility industry. The paper's central aim is to identify and describe the implications of strategic rigidness for a utility firm's decision making in adopting newer renewable energy technologies. The findings indicate that not all utility firms are keen to adopt these new technologies, as these firms have traditionally been operating efficiently with a more conventional and mature technological arrangement that has become embedded in the organisational routine. Case studies of Iberdrola S.A. and Enel S.p.A. as major electric utilities are detailed to document mergers and acquisitions and technology adoption decisions. The results indicate that technology adoption behaviours vary widely across utility firms with different organisational learning processes and core capabilities.

Aplicación de nuevas tecnologías en los sistemas de alumbrado

A medida que transcurre el tiempo la sociedad evoluciona, las ciudades crecen, se modernizan, mejoran su infraestructura y se ofrecen más y mejores servicios a sus ciudadanos. Esto ha hecho que durante muchos años las ciudades se hayan desarrollado sin pensar en lo que vendrá más adelante, contaminando el medio ambiente y consumiendo mucha energía y de forma ineficiente. Ante esta situación, y gracias a las innovaciones tecnológicas en materia de comunicaciones, se están adoptando medidas para dirigir la evolución de las ciudades hacia un modelo de ciudad inteligente y sostenible. Las redes de comunicaciones constituyen uno de los pilares sobre los que se asienta la sociedad, que se encuentra siempre en contacto con su entorno. Cada vez más, se tiene una mayor necesidad de conocer lo que ocurre en el entorno en tiempo real solicitando información climatológica en una determinada ubicación, permitiendo conocer el estado del tráfico para elegir la ruta hacia el trabajo, saber el tiempo que tardará el autobús en llegar a la parada, etc. Como éstos, se podrían citar muchos más ejemplos de necesidades y servicios que demandan hoy día la sociedad y que, seguramente, nadie pensaba que las iba a necesitar hace unos años. Muchos de estos servicios en tiempo real se consiguen gracias a las redes de sensores inalámbricas. Consiste en desplegar una serie de diminutos sensores en una zona determinada con el objetivo de recoger la información del medio, procesarla y modelarla para que esté disponible para los usuarios. Observando la tendencia seguida por las Tecnologías de la Información y de las Comunicaciones (TIC) se puede constatar una continua evolución hacia los dispositivos embedidos, de cada vez más pequeño tamaño y menor consumo y, al mismo tiempo, con mayor capacidad de proceso y memoria y facilidad para las comunicaciones. Siguiendo esta línea, se está construyendo la ciudad inteligente con capacidad para pensar y tomar decisiones, pero hay que dotarla de cierto grado de eficiencia. Se trata de aprovechar los recursos de la naturaleza para crear fuentes de energías limpias e ilimitadas. Empleando las tecnologías oportunas para transformar, por ejemplo, la energía del Sol o la energía del viento en electricidad, se puede alcanzar el modelo de ciudad que se pretende. ABSTRACT. As time passes society evolves, cities grow, modernize, improve their infrastructure and offer more and better services to their citizens. This has made for many years cities have developed without thinking about what will come later , polluting the environment and high energy consuming and inefficient . Given this situation, and thanks to the Technological innovations in communications, is being taken to direct the evolution of cities towards a smart city model sustainable. Communication networks are one of the pillars on which society rests, which is always in contact with their environment. Increasingly, there is a greater need to know what happens in the real-time environment requesting weather information in a certain location , allowing know the traffic to choose the route to work , namely the time take the bus to get to the bus stop, etc. . As these, you could cite many more Examples of needs and services that society demands today and, surely, no one thought that was going to need a few years ago. Many of these real-time services are achieved through networks wireless sensors. Is to deploy a series of sensors in a tiny given area in order to collect information from the environment, process and shape it to make it available to users. Observing the trend followed by the Information Technology and Communications (ICT ) can finding an evolving toward embeded devices of increasingly small size and lower power consumption and at the same time, higher capacity process and memory ease communications. Following this line, is under construction with capacity smart city to think and make decisions, but you have to give it some degree of efficiency. It seeks to harness the resources of nature to create clean energy sources and unlimited. Using appropriate technologies to transform, for example, energy from the sun or wind energy into electricity, it can achieve the model city intended.

Solar driven energy conversion applications based on 3C-SiC

There is a strong and growing worldwide research on exploring renewable energy resources. Solar energy is the most abundant, inexhaustible and clean energy source, but there are profound material challenges to capture, convert and store solar energy. In this work, we explore 3C-SiC as an attractive material towards solar-driven energy conversion applications: (i) Boron doped 3C-SiC as candidate for an intermediate band photovoltaic material, and (ii) 3C-SiC as a photoelectrode for solar-driven water splitting. Absorption spectrum of boron doped 3C-SiC shows a deep energy level at ~0.7 eV above the valence band edge. This indicates that boron doped 3C-SiC may be a good candidate as an intermediate band photovoltaic material, and that bulk like 3C-SiC can have sufficient quality to be a promising electrode for photoelectrochemical water splitting.

Effects on the shallow aquifers by CO2 leakages in a tertiary basin (province of Murcia, Spain)

Geological storage of CO2 is nowadays internationally considered as the most effective method for greenhouse gas emission mitigation, in order to minimize its effects on the global climatology. One of the main options is to store CO2 in deep saline aquifers at more than 800m depth, because it reaches its supercritical state. Study of the CO2 natural accumulations as natural analogues of an artificial CO2 storage is very useful in order to understand the CO2 long term behaviour and thus to predict its possible impact on the surficial environment and life. Therefore the main objective of this work is to detect the affection of the CO2 leakages from a deep saline aquifer on the shallow aquifers, all of them located in the Gañuelas-Mazarrón Tertiary basin (Province of Murcia, Spain). This CO2 storage and leakage natural system can be analogous to an artificial CO2 storage with leakage phenomena. In order to reach these objectives, groundwaters from different aquifers in the site have been sampled and analysed for major elements, free and dissolved gases and stable isotopes, particularly ∂ 13 C and 3 He/ 4 He. The results obtained allow to conclude that this natural system is an interesting example of natural analogue for an artificial CO2 storage affected by leakage processes because the shallow fresh aquifers in the site are polluted by CO2 from the deep saline aquifer as a consequence of an intensive over-exploitation of these freshwater aquifers

Thermal effects and other interesting issues with CPV lenses

The Photovoltaic (PV) Module Reliability Workshop was held in Golden, Colorado, on Feb. 28?March 1, 2012. The objective was to share information to improve PV module reliability because such improvements reduce the cost of solar electricity and give investors confidence in the technology. NREL led the workshop, which was sponsored by the U.S. Department of Energy (DOE) Solar Energy Technologies Program (Solar Program).

Biokerosene from coconut, babassu, camelina and palm kernel oils: production and properties of their blends with fossil kerosene

On December 20th 2006 the European Commission approved a law proposal to include the civil aviation sector in the European market of carbon dioxide emission rights [European Union Emissions Trading System, EUETS). On July 8th 2009, the European Parliament and Conseil agreed that all flights leaving or landing in the EU airports starting from January 1st 2012 should be included in the EUETS. On November 19th 2008, the EU Directive 2008/101/CE [1] included the civil aviation activities in the EUETS, and this directive was transposed by the Spanish law 13/2010 of July 5th 2010 [2]. Thus, in 2012 the aviation sector should reduce their emissions to 97 % of the mean values registered in the period 2004-2006, and for 2013 these emission reductions should reach 95 % of the mean values for that same period. Trying to face this situation, the aviation companies are planning seriously the use of alternative jet fuels to reduce their greenhouse gas emissions and to lower their costs. However, some US airlines have issued a lawsuit before the European Court of Justice based in that this EU action violates a long standing worldwide aviation treaty, the Chicago convention of 1944, and also the Chinese aviation companies have rejected to pay any EU carbon dioxide tax [3]. Moreover, the USA Departments of Agriculture and Energy and the Navy will invest a total of up to $150 million over three years to spur production of aviation and marine biofuels for commercial and military applications [4]. However, the jet fuels should fulfill a set of extraordinarily sensitive properties to guarantee the safety of planes and passengers during all the flights.

Inertial behavior of offshore devices

In the last years, there has been a continued growth in the number of offshore operations for handling large equipment and objects, with emphasis on installation and maintenance of devices for exploiting marine renewable energy like generators for harnessing wind, waves and currents energy. Considering the behaviour of these devices during manoeuvrings, and due to their size and by the interaction with the surrounding fluid, the effect of inertial forces and torques is very important, which requires a specific modelling. This paper especially discusses the masses and moments of inertia modelling problem, with the aim to use it in the simulation of the complex manoeuvres of these devices and in the automatic control systems designed for their offshore operations. Given the importance and complexity of the added mass modelling, a method for its early design identification, developed by the R&D Group on Marine Renewable Energy Technologies of the UPM (GITERM) and its use on special cases like emersion manoeuvres of devices from underwater to the surface will be presented.

Aplicación de energía geotérmica de muy baja entalpia para la climatización de un edificio de oficinas en Alcorcón, Madrid

El presente Proyecto tiene como propósito el estudio de la viabilidad de la implantación de energía geotérmica de muy baja entalpia para la climatización de un edificio empresarial en Madrid. Para ello se emplearon cálculos teóricos y simulaciones realizadas mediante programas informaticos especializados con el fin de estimar los parámetros técnicos necesarios para su viabilidad. Se estimo el suministro de la potencia necesaria a través de tres bombas de calor tipo agua-agua que sustituyen a las bombas de calor aire-agua individuales anteriormente instaladas. El intercambio de calor se realiza a través de sondas geotérmicas U-Simple. Se dimensionaron los colectores, bombas de circulación, deposito de inercia y vaso de expansión necesarios para funcionamiento del sistema. El estudio económico determino la necesidad de una alta inversión inicial, con una rentabilidad a medio plazo. Además de los beneficios económicos se realizo un estudio de las emisiones de gases de efecto invernadero demostrando la reducción de los mismos, lo que refleja que además de ser una tecnología económicamente viable es una energía limpia. ABSTRACT The objective of the present project is to evaluate the viability of the imposition of a low-enthalpy geothermal energy system for air conditioning in a business building in Madrid. In this study, both theoretical calculations and numerical simulations in specialized programs were used in order to estimate the technical parameters needed for its viability. We estimated the necessary power supply, which is delivered by three heat water-water pumps that substitute the individual heat air-water pumps previously installed. The heat exchange is achieved through geothermal vertical simple-U probes. Also in this work we have measured the collectors, flow pumps, inertia deposit and the water expansion vessel needed for the proper operation of the system. The economic study determined the need of a high initial investment with mid-term profit. In addition to the economic benefits, the greenhouse gases emissions were evaluated, finding that the geothermal energy system implies a reduction of these emissions. This reflects the fact that, in addition to being economically viable, the geothermal energy is considered a clean energy.

Aerodinámica experimental de elementos de parques energéticos

La creciente demanda de energía eléctrica y la necesidad de implementar energías no contaminantes hace que las llamadas tecnologías verdes sean cada día más solicitadas. Entre estas tecnologías encontramos la energía solar y la energía eólica; ambas tienen una trayectoria de uso e investigación bastante amplia, sin embargo aún presentan problemas de fondo que impiden dar mayor impulso a su uso. El objetivo de la presente tesis es presentar soluciones a problemas de optimización en campos conversores de energía. Para ello se analizan y resuelven dos problemas por medio de técnicas de aerodinámica experimental: el primero sobre campos de colectores solares y el segundo sobre campos eólicos. Las técnicas de medición utilizadas en aerodinámica, y en el presente trabajo, son: medición de cargas, anemometría de hilo caliente, velocimetría por imagen de partículas y escaneo de presiones; además de un análisis estadístico de los datos. En el primer caso se ensayan experimentalmente colectores solares parabólicos en donde, por cuestiones de seguridad o por protección contra el viento, se utilizan cercas. Éstas modifican el comportamiento del flujo corriente abajo y se ha encontrado que la distancia a la cual se colocan, así como el tipo de cercas (sólida o permeable), modifican las cargas estructurales a las que los colectores están expuestos. Los resultados demuestran que existe una distancia crítica en la cual la presencia de la cerca aumenta la carga en lugar de disminuirla, por lo cual la selección adecuada del parapeto y la distancia a la cual se coloca son de suma importancia para la optimización de la estructura. En el segundo caso se ensaya experimentalmente y simula numéricamente la estela de turbinas eólicas por medio de discos porosos. En donde un disco permeable simula el rotor de una turbina. El disco es capaz de semejar la estela y los efectos que ésta puede causar corriente abajo. Los resultados muestran que seleccionando adecuadamente la porosidad, es posible simular coeficientes de empuje similares a los desarrollados por los aerogeneradores, además la estela y sus efectos son semejantes a los medidos en campo. ABSTRACT The called green energy technologies are increasingly required because of the growing demand for electricity and the need to implement nonpolluting energy. Among the green energy technologies it is found the solar and the wind energy, both have a history of use and fairly extensive research; however they still have problems which limit to give them further impetus to its use. The aim of this thesis is to present solutions to optimization problems in energy harvesting. To this end it is analysed, and solved, two problems by means of techniques in experimental aerodynamics: the first issue with regard to parabolic troughs and the second about wind farms. The measurement techniques commonly used in aerodynamics, and used in this research work, are: measurement of loads, hot wire anemometry, particle image velocimetry and scanning of pressures; where data are collected and then an statistical analysis is done. In the first case it is tested parabolic troughs where, either for security reasons or protection against the wind actions, fences are used. These fences modify the behaviour of flow downstream and it was found that the distance at which they are placed, and the type of fences (solid or permeable) modify the structural loads to which the parabolic troughs are exposed. The results show that there is a critical distance at which the presence of the fence increases the load instead of protecting the parabolic trough, hence making the proper selection of the parapet and the distance at which it stands are paramount for the optimization of the structure. In the second case it is tested, experimentally and numerically, the wake of wind turbines by means of porous disks; where the permeable disc simulates a turbine rotor. The disc is able to mimic the wake and the effects that it can cause downstream. The results show that by properly selecting the porosity, it is possible to simulate drag coefficients similar to those developed by wind turbines; moreover the porous disk wake and its effects are similar to those measured on field.

Sistema autónomo para carga de baterías mediante una instalación fotovoltaica con aplicación directa al vehículo eléctrico y usos

La situación energética actual es insostenible y como consecuencia se plantea un escenario próximo orientado a conseguir un futuro energético sostenible que permita el desarrollo económico y el bienestar social. La situación ambiental actual está afectada directamente por la combustión de combustibles fósiles que en 2013 constituyeron el 81% de la energía primaria utilizada por el ser humano y son la principal fuente antropogénica de gases de efecto invernadero. Los informes del IPCC1, ponen de manifiesto que el cambio climático se ha consolidado durante los últimos años y en la conferencia de la ONU sobre cambio climático de París que se celebrará a finales de 2015, se pretende que los gobiernos suscriban un acuerdo universal para limitar las emisiones de gases de efecto invernadero y evitar que el incremento de la temperatura media global supere los 2°C. Por otra parte, en el interior de las ciudades es especialmente preocupante, por su efecto directo sobre la salud humana, el impacto ambiental producido por las emisiones de NOx que generan el transporte de personas y mercancías. El sector del transporte fue responsable en 2012 del 27,9% del consumo final de energía. Una vez expuesto el escenario energético y ambiental actual, en esta tesis, se analiza la eficiencia de un sistema autónomo fotovoltaico para la carga de baterías de vehículos eléctricos y el uso del mismo con otras cargas, con el objetivo de aprovechar al máximo la energía eléctrica generada y contribuir a la utilización de energía limpia que no produzca impacto ambiental. Como primer paso para el desarrollo de la tesis se hizo un estudio de trabajos previos comenzando por las primeras aplicaciones de la energía fotovoltaica en los vehículos solares para después pasar a trabajos más recientes enfocados al suministro de energía a los vehículos eléctricos. También se hizo este estudio sobre las metodologías de simulación en los sistemas fotovoltaicos y en el modelado de distintos componentes. Posteriormente se eligieron, dentro de la amplia oferta existente en el mercado, los componentes con características técnicas más adecuadas para este tipo de instalaciones y para las necesidades que se pretenden cubrir. A partir de los parámetros técnicos de los componentes elegidos para configurar la instalación autónoma y utilizando modelos contrastados de distintos componentes, se ha desarrollado un modelo de simulación en ordenador del sistema completo con el que se han hecho simulaciones con distintos modos de demanda de energía eléctrica, según los modos de carga disponibles en el vehículo eléctrico para corriente alterna monofásica de 230 V. También se han simulado distintos tamaños del generador fotovoltaico y del sistema de acumulación de energía eléctrica para poder determinar la influencia de estos parámetros en los balances energéticos del sistema. Utilizando recursos propios el doctorando ha realizado la instalación real de un sistema fotovoltaico que incluye sistema de acumulación e inversor en un edificio de su propiedad. Para la realización de la tesis, La Fundación de Fomento e Innovación Industrial (F2I2) ha facilitado al doctorando un dispositivo que permite realizar la alimentación del vehículo eléctrico en modo 2 (este modo emplea un adaptador que incorpora dispositivos de seguridad y se comunica con el vehículo permitiendo ajustar la velocidad de recarga) y que ha sido necesario para los trabajos desarrollados. Se ha utilizado la red eléctrica como sistema de apoyo de la instalación fotovoltaica para permitir la recarga en el modo 2 que requiere más potencia que la proporcionada por el sistema fotovoltaico instalado. Se han analizado mediante simulación distintos regímenes de carga que se han estudiado experimentalmente en la instalación realizada, a la vez que se han hecho ensayos que se han reproducido mediante simulación con los mismos valores de radiación solar y temperatura con objeto de contrastar el modelo. Se han comparado los resultados experimentales con los obtenidos mediante simulación con objeto de caracterizar el comportamiento del sistema de acumulación (energía eléctrica suministrada y tensión de salida en las baterías) y del generador fotovoltaico (energía eléctrica fotovoltaica suministrada). Por último, se ha realizado un estudio económico de la instalación autónoma fotovoltaica ejecutada y simulada. En el mismo se ha planteado la utilización de fondos propios (como realmente se ha llevado a cabo) y la utilización de financiación, para determinar dos posibles escenarios que pudieran ser de utilidad a un propietario de vehículo eléctrico. Se han comparado los resultados obtenidos en los dos escenarios propuestos del estudio económico del sistema, en cuanto a los parámetros de tiempo de retorno de la inversión, valor actual neto de la inversión y tasa interna de retorno de la misma. Las conclusiones técnicas obtenidas, permiten la utilización del sistema con los modos de carga ensayados y otro tipo de cargas que aprovechen la generación eléctrica del sistema. Las baterías ofrecen mejor comportamiento cuando el aporte fotovoltaico está presente, pero no considera adecuado la conexión de cargas elevadas a un sistema de acumulación de gel (plomo-acido) como el que se ha utilizado, debido al comportamiento de este tipo de baterías ante demandas de intensidad de corriente eléctrica elevadas. Por otra parte, el comportamiento de este tipo de baterías con valores de intensidad de corriente eléctrica inferiores a 10 A en ausencia de energía fotovoltaica, con el objetivo de utilizar la generación de energía eléctrica diaria acumulada en el sistema, sí resulta interesante y ofrece un buen comportamiento del sistema de acumulación. Las circunstancias actuales de mercado, que carece de sistemas de acumulación de litio con precios de compra interesantes, no han permitido poder experimentar este sistema de acumulación en la instalación autónoma fotovoltaica ejecutada, tampoco se ha podido obtener el favor de ningún fabricante para ello. Actualmente hay disponibles sistemas de acumulación en litio que no se comercializan en España y que serían adecuados para el sistema de acumulación de energía propuesto en este estudio, que deja abierta las puertas para futuros trabajos de investigación. Las conclusiones económicas obtenidas, rentabilizan el uso de una instalación autónoma fotovoltaica con consumo instantáneo, sin acumulación de energía eléctrica. El futuro de conexión a red por parte de estas instalaciones, cuando se regule, aportará un incentivo económico para rentabilizar con menos tiempo las instalaciones autónomas fotovoltaicas, esto también deja la puerta abierta a futuros trabajos de investigación. El sistema de acumulación de energía aporta el mayor peso económico de inversión en este tipo de instalaciones. La instalación estudiada aporta indicadores económicos que la hacen rentable, pero se necesitaría que los precios de acumulación de la energía en sistemas eficientes estén comprendidos entre 100-200 €/kWh para que el sistema propuesto en este trabajo resulte atractivo a un potencial propietario de un vehículo eléctrico. ABSTRACT The current energy situation is untenable; it poses a scenario next focused on reaching a sustainable energy future, to allow economic development and social welfare. The environmental current situation is affected directly by the combustion of fossil fuels that in 2013 constituted 81 % of the primary energy used by the human being and they are the principal source human of greenhouse gases. The reports of the IPCC2, they reveal that the climate change has consolidated during the last years and in the conference of the UNO on climate change of Paris that will be celebrated at the end of 2015, there is claimed that the governments sign a universal agreement to limit the emission of greenhouse gases and to prevent that the increase of the global average temperature overcomes them 2°C. On the other hand, inside the cities it is specially worrying, for his direct effect on the human health, the environmental impact produced by the NOx emissions that generate the persons' transport and goods. The sector of the transport was responsible in 2012 of 27,9 % of the final consumption of energy. Once exposed the scenario and present environmental energy, in this thesis, it has analyzed the efficiency of an autonomous photovoltaic system for charging electric vehicles, and the use of the same with other workloads, with the objective to maximize the electrical energy generated and contribute to the use of clean energy that does not produce environmental impact. Since the first step for the development of the thesis did to itself a study of previous works beginning for the first applications of the photovoltaic power in the solar vehicles later to go on to more recent works focused on the power supply to the electrical vehicles. Also this study was done on the methodologies of simulation in the photovoltaic systems and in the shaped one of different components. Later they were chosen, inside the wide existing offer on the market, the components with technical characteristics more adapted for this type of facilities and for the needs that try to cover. From the technical parameters of the components chosen to form the autonomous installation and using models confirmed of different components, a model of simulation has developed in computer of the complete system with which simulations have been done by different manners of demand of electric power, according to the available manners of load in the electrical vehicle for single-phase alternating current of 230 V. Also there have been simulated different sizes of the photovoltaic generator and of the system of accumulation of electric power to be able to determine the influence of these parameters in the energy balances of the system. Using own resources the PhD student has realized a real installation of a photovoltaic system that includes system of accumulation and investing in a building of his property. For the accomplishment of the thesis, The Foundation of Promotion and Industrial Innovation (F2I2) it has facilitated to the PhD student a device that allows to realize the supply of the electrical vehicle in way 2 (this way uses an adapter that incorporates safety devices and communicates with the vehicle allowing to fit the speed of recharges) and that has been necessary for the developed works. The electrical network has been in use as system of support of the photovoltaic installation for allowing it her recharges in the way 2 that more power needs that provided by the photovoltaic installed system. There have been analyzed by means of simulation different rate of load that have been studied experimentally in the realized installation, simultaneously that have done to themselves tests that have reproduced by means of simulation with the same values of solar radiation and temperature in order the model contrasted. The experimental results have been compared by the obtained ones by means of simulation in order to characterize the behavior of the system of accumulation (supplied electric power and tension of exit in the batteries) and of the photovoltaic generator (photovoltaic supplied electric power). Finally, there has been realized an economic study of the autonomous photovoltaic executed and simulated installation. In the same one there has appeared the utilization of own funds (since really it has been carried out) and the utilization of financing, to determine two possible scenes that could be of usefulness to an owner of electrical vehicle. There have been compared the results obtained in both scenes proposed of the economic study of the system, as for the parameters of time of return of the investment, current clear value of the investment and rate hospitalizes of return of the same one. The technical obtained conclusions, they make the utilization of the system viable with the manners of load tested and another type of loads of that they take advantage the electrical generation of the system. The batteries offer better behavior when the photovoltaic contribution is present, but he does not consider to be suitable the connection of loads risen up to a system of accumulation of gel (lead - acid) as the one that has been in use, due to the behavior of this type of batteries before demands of intensity of electrical current raised. On the other hand, the behavior of this type of batteries with low values of intensity of electrical current to 10 To in absence of photovoltaic power, with the aim to use the generation of daily electric power accumulated in the system, yes turns out to be interesting and offers a good behavior of the system of accumulation. The current circumstances of market, which lacks systems of accumulation of lithium with interesting purchase prices, have not allowed to be able to experience this system of accumulation in the autonomous photovoltaic executed installation, neither one could have obtained the favor of any manufacturer for it. Nowadays there are available systems of accumulation in lithium that is not commercialized in Spain and that they would be adapted for the system of accumulation of energy proposed in this study, which makes the doors opened for future works of investigation. The economic obtained conclusions; they make more profitable the use of an autonomous photovoltaic installation with instantaneous consumption, without accumulation of electric power. The future of connection to network on the part of these facilities, when it is regulated, will contribute an economic incentive to make profitable with less time the autonomous photovoltaic facilities, this also leaves the door opened for future works of investigation. The system of accumulation of energy contributes the major economic weight of investment in this type of facilities. The studied installation contributes economic indicators that make her profitable, but it would be necessary that the prices of accumulation of the energy in efficient systems are understood between 100-200 € in order that the system proposed in this work turns out to be attractive to a proprietary potential of an electrical vehicle.

Comparison of CO2 From Coal Capture Processes and Valorisation Technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorising CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorise captured CO2. Valorising captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2 capture and valorising will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Comparison of CO2 from coal captureprocesses and valorisation technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorizing CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorizecaptured CO2. Valorizing captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2capture and valorizing will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Assessment of energy efficiency and sustainability scenarios in the transport system

Background Energy Policy is one of the main drivers of Transport Policy. A number of strategies to reduce current energy consumption trends in the transport sector have been designed over the last decades. They include fuel taxes, more efficient technologies and changing travel behavior through demand regulation. But energy market has a high degree of uncertainty and the effectiveness of those policy options should be assessed. Methods A scenario based assessment methodology has been developed in the frame of the EU project STEPS. It provides an integrated view of Energy efficiency, environment, social and competitiveness impacts of the different strategies. It has been applied at European level and to five specific Regions. Concluding remarks The results are quite site specific dependent. However they show that regulation measures appear to be more effective than new technology investments. Higher energy prices could produce on their turn a deterioration of competitiveness and a threat for social goals.