Calibration process on the study of new antenna array architectures for space communications

This paper introduces novel calibration processes applied to antenna arrays with new architectures and technologies designed to improve the performance of traditional earth stations for satellite communications due to the increasing requirement of data capacity during last decades. Besides, the Radiation Group from the Technical University of Madrid has been working on the development of new antenna arrays based on novel architecture and technologies along many projects as a solution for the ground segment in the early future. Nowadays, the calibration process is an interesting and cutting edge research field in a period of expansion with a lot of work to do for calibration in transmission and also for reception of these novel antennas under development.

Nitrous oxide emissions from European agriculture - an analysis of variability and drivers of emissions from field experiments

Nitrous oxide emissions from a network of agricultural experiments in Europe were used to explore the relative importance of site and management controls of emissions. At each site, a selection of management interventions were compared within replicated experimental designs in plot-based experiments. Arable experiments were conducted at Beano in Italy, El Encin in Spain, Foulum in Denmark, Logarden in Sweden, Maulde in Belgium CE1, Paulinenaue in Germany, and Tulloch in the UK. Grassland experiments were conducted at Crichton, Nafferton and Peaknaze in the UK, Godollo in Hungary, Rzecin in Poland, Zarnekow in Germany and Theix in France. Nitrous oxide emissions were measured at each site over a period of at least two years using static chambers. Emissions varied widely between sites and as a result of manipulation treatments. Average site emissions (throughout the study period) varied between 0.04 and 21.21 kg N2O-N ha−1yr−1, with the largest fluxes and variability associated with the grassland sites. Total nitrogen addition was found to be the single most important deter- minant of emissions, accounting for 15 % of the variance (using linear regression) in the data from the arable sites (p<0.0001), and 77 % in the grassland sites. The annual emissions from arable sites were significantly greater than those that would be predicted by IPCC default emission fac- tors. Variability of N2O emissions within sites that occurred as a result of manipulation treatments was greater than that resulting from site-to-site and year-to-year variation, highlighting the importance of management interventions in contributing to greenhouse gas mitigation

Proceso metodológico para optimizar la toma de decisiones en el proyecto de envolventes arquitectónicas multicapa = Methodological process for the optimization of the decision making in multilayer building envelope projects

La presente tesis doctoral se enmarca dentro del concepto de la sistematización del conocimiento en arquitectura, más concretamente en el campo de las construcciones arquitectónicas y la toma de decisiones en la fase de proyecto de envolventes arquitectónicas multicapa. Por tanto, el objetivo principal es el establecimiento de las bases para una toma de decisiones informadas durante el proyecto de una envolvente multicapa con el fin de colaborar en su optimización. Del mismo modo que la historia de la arquitectura está relacionada con la historia de la innovación en construcción, la construcción está sujeta a cambios como respuesta a los fracasos anteriores. En base a esto, se identifica la toma de decisiones en la fase de proyecto como el estadio inicial para establecer un punto estratégico de reflexión y de control sobre los procesos constructivos. La presente investigación, conceptualmente, define los parámetros intervinientes en el proyecto de envolventes arquitectónicas multicapa a partir de una clasificación y sistematización de todos los componentes (elementos, unidades y sistemas constructivos) utilizados en las fachadas multicapa. Dicha sistematización se materializa en una hoja matriz de datos en la que, dentro de una organización a modo de árbol, se puede acceder a la consulta de cada componente y de su caracterización. Dicha matriz permite la incorporación futura de cualquier componente o sistema nuevo que aparezca en el mercado, relacionándolo con aquellos con los que comparta ubicación, tipo de material, etc. Con base en esa matriz de datos, se diseña la sistematización de la toma de decisiones en la fase de proyecto de una envolvente arquitectónica, en concreto, en el caso de una fachada. Operativamente, el resultado se presenta como una herramienta que permite al arquitecto o proyectista reflexionar y seleccionar el sistema constructivo más adecuado, al enfrentarse con las distintas decisiones o elecciones posibles. La herramienta se basa en las elecciones iniciales tomadas por el proyectista y se estructura, a continuación y sucesivamente, en distintas aproximaciones, criterios, subcriterios y posibilidades que responden a los distintos avances en la definición del sistema constructivo. Se proponen una serie de fichas operativas de comprobación que informan sobre el estadio de decisión y de definición de proyecto alcanzados en cada caso. Asimismo, el sistema permite la conexión con otros sistemas de revisión de proyectos para fomentar la reflexión sobre la normalización de los riesgos asociados tanto al proprio sistema como a su proceso constructivo y comportamiento futuros. La herramienta proporciona un sistema de ayuda para ser utilizado en el proceso de toma de decisiones en la fase de diseño de una fachada multicapa, minimizando la arbitrariedad y ofreciendo una cualificación previa a la cuantificación que supondrá la elaboración del detalle constructivo y de su medición en las sucesivas fases del proyecto. Al mismo tiempo, la sistematización de dicha toma de decisiones en la fase del proyecto puede constituirse como un sistema de comprobación en las diferentes fases del proceso de decisión proyectual y de definición de la envolvente de un edificio. ABSTRACT The central issue of this doctoral Thesis is founded on the framework of the concept of the systematization of knowledge in architecture, in particular, in respect of the field of building construction and the decision making in the design stage of multilayer building envelope projects. Therefore, the main objective is to establish the bases for knowledgeable decision making during a multilayer building envelope design process, in order to collaborate with its optimization. Just as the history of architecture is connected to the history of innovation in construction, construction itself is subject to changes as a response to previous failures. On this basis, the decisions made during the project design phase are identified as the initial state to establish an strategic point for reflection and control, referred to the constructive processes. Conceptually, this research defines the parameters involving the multilayer building envelope projects, on the basis of a classification and systematization for all the components (elements, constructive units and constructive systems) used in multilayer façades. The mentioned systematization is materialized into a data matrix sheet in which, following a tree‐like organization, the access to every single component and its characterization is possible. The above data matrix allows the future inclusion of any new component or system that may appear in the construction market. That new component or system can be put into a relationship with another, which it shares location, type of material,… with. Based on the data matrix, the systematization of the decision making process for a building envelope design stage is designed, more particularly in the case of a façade. Putting this into practice, it is represented as a tool which allows the architect or the designer, to reflect and to select the appropriate building system when facing the different elections or the different options. The tool is based on the initial elections taken by the designer. Then and successively, it is shaped on the form of different operative steps, criteria, sub‐criteria and possibilities which respond to a different progress in the definition of the building construction system. In order to inform about the stage of the decision and the definition reached by the project in every particular case, a range of operative sheets are proposed. Additionally, the system allows the connection with other reviewing methods for building projects. The aim of this last possibility is to encourage the reflection on standardization of the associated risks to the building system itself and its future performance. The tool provides a helping system to be used during the decision making process for a multilayer façade design. It minimizes the arbitrariness and offers a qualification previous to the quantification that will be done with the development of the construction details and their bill of quantities, that in subsequent project stages will be executed. At the same time, the systematization of the mentioned decision making during the design phase, can be found as a checking system in the different stages of the decision making design process and in the different stages of the building envelope definition.

CO2 emissions from a spark ignition engine operatin on natural-hydrogen blends (HCNG)

The addition of hydrogen to natural gas could be a short-term alternative to today’s fossil fuels, as greenhouse gas emissions may be reduced. The aim of this study is to evaluate the emissions and performance of a spark ignition engine fuelled by pure natural gas, pure hydrogen, and different blends of hydrogen and natural gas (HCNG). Increasing the hydrogen fraction leads to variations in cylinder pressure and CO2 emissions. In this study, a combustion model based on thermodynamic equations is used, considering separate zones for burned and unburned gases. The results show that the maximum cylinder pressure rises as the fraction of hydrogen in the blend increases. The presence of hydrogen in the blend leads to a decrease in CO2 emissions. Due to the properties of hydrogen, leaner fuel–air mixtures can be used along with the appropriate spark timing, leading to an improvement in engine emissions with no loss of performance.

Role of maize stover incorporation on nitrogen oxide emissions in a non-irrigated Mediterranean barley field.

Aims Agricultural soils in semiarid Mediterranean areas are characterized by low organic matter contents and low fertility levels. Application of crop residues and/or manures as amendments is a cost-effective and sustainable alternative to overcome this problem. However, these management practices may induce important changes in the nitrogen oxide emissions from these agroecosystems, with additional impacts on carbon dioxide emissions. In this context, a field experiment was carried out with a barley (Hordeum vulgare L.) crop under Mediterranean conditions to evaluate the effect of combining maize (Zea mays L.) residues and N fertilizer inputs (organic and/or mineral) on these emissions. Methods Crop yield and N uptake, soil mineral N concentrations, dissolved organic carbon (DOC), denitrification capacity, N2O, NO and CO2 fluxes were measured during the growing season. Results The incorporation of maize stover increased N2O emissions during the experimental period by c. 105 %. Conversely, NO emissions were significantly reduced in the plots amended with crop residues. The partial substitution of urea by pig slurry reduced net N2O emissions by 46 and 39 %, with and without the incorporation of crop residues respectively. Net emissions of NO were reduced 38 and 17 % for the same treatments. Molar DOC:NO 3 − ratio was found to be a robust predictor of N2O and NO fluxes. Conclusions The main effect of the interaction between crop residue and N fertilizer application occurred in the medium term (4–6 month after application), enhancing N2O emissions and decreasing NO emissions as consequence of residue incorporation. The substitution of urea by pig slurry can be considered a good management strategy since N2O and NO emissions were reduced by the use of the organic residue.

Capacidad y comportamiento de la adsorción de fenol en caolines naturales y modificados

En la actualidad las industrias químicas, farmacéuticas y clínicas, originan contaminantes en aguas superficiales, aguas subterráneas y suelos de nuestro país, como es el caso del fenol, contaminante orgánico común y altamente dañino para los organismos, incluso a bajas concentraciones. Existen en el mercado diferentes metodologías para minimizar la contaminación pero muchos de estos procesos tienen un alto coste, generación de contaminantes, etc. La adsorción de contaminantes por medio de arcillas es un método ampliamente utilizado, encontrándose eficaz y económico. Pero la dificultad de adsorber un contaminante orgánico como el fenol motiva la creación de un material llamado organoarcillas. Las organoarcillas son arcillas modificadas con un surfactante, a su vez, los surfactantes son moléculas orgánicas que confieren a la superficie de la arcilla carga catiónica en lugar de aniónica, haciendo más fácil la adsorción de fenol. Para esta tesis se ha elegido el caolín como material adsorbente, fácilmente disponible y relativamente de bajo coste. Se ha trabajado con: arenas de caolín, material directo de la extracción, y caolín lavado, originado del proceso de lavado de las arenas de caolín. Ambos grupos se diferencian fundamentalmente por su contenido en cuarzo, ampliamente mayor en las arenas de caolín. Con el objetivo de desarrollar un material a partir del caolín y arenas de éste con capacidad de retención de contaminates, en concreto, fenol, se procedió a modificar los materiales de partida mediante tratamientos térmicos, mecánicos y/o químicos, dando lugar a compuestos con mayor superficie química reactiva. Para ello se sometió el caolín y las arenas caoliníferas a temperaturas de 750ºC durante 3h, a moliendas hasta alcanzar su amorfización, y/o a activaciones con HCl 6M o con NaOH 5M durante 3h a 90ºC. En total se obtuvieron 18 muestras, en las que se estudiaron las características físico-químicas, mineralógicas y morfológicas de cada una de ellas con el fin de caracterizarlas después de haber sufrido los tratamientos y/o activaciones químicas. Los cambios producidos fueron estudiados mediante pH, capacidad de intercambio catiónico (CEC), capacidad de adsorción de agua (WCU y CWC), distribución de tamaño de partícula (PSD), área de superficie específica (SBET), difracción de rayos X (XRD), espectroscopía infrarroja por transformada de Fourier (FTIR), métodos térmicos (TG, DTG y DTA), y microscopía electrónica de transmisión y barrido (SEM y TEM). Además se analizó los cambios producidos por los tratamientos en función de las pérdidas de Al y Si que acontece en las 18 muestras. Los resultados para los materiales derivados de la arenas caoliníferas fueron similares a los obtenidos para los caolines lavados, la diferencia radica en la cantidad de contenido de caolinita en los diferente grupos de muestras. Apoyándonos en las técnicas de caracterización se puede observar que los tratamientos térmico y molienda produce materiales amorfos, este cambio en la estructura inicial sumado a las activaciones ácida y alcalina dan lugar a pérdidas de Si y Al, ocasionando que sus propiedades físico-químicas, mineralógicas y morfológicas se vean alteradas. Un fuerte aumento es observado en las áreas superficiales y en la CEC en determinadas muestras, además entre los cambios producidos se encuentra la producción de diferentes zeolitas en porcentajes distintos con el tratamiento alcalino. Para la obtención de las organoarcillas, las 18 muestras se sometieron a la surfactación con hexadeciltrimetil amonio (HDTMA) 20 mM durante 24h a 60ºC, esta concentración de tensioactivo fue más alta que la CEC de cada muestra. Los camext bios anteriormente producidos por los tratamientos y activaciones, afectan de forma diferente en la adsorción de HDTMA, variando por tanto la adsorción del surfactante en la superficie de las muestras. Se determinó el tensioactivo en superficie por FTIR, además se realizó un análisis de componentes principales (PCA) para examinar la dependencia entre las relaciones Si/Al de las muestras en la capacidad de adsorción de tensioactivo, y para el estudio de la adsorción de HDTMA en las muestras se realizaron además del análisis termogravimétrico, aproximaciones con los modelos de Freundllich y Langmuir. Se persigue conocer las diferentes formas y maneras que tiene el tensioactivo de fijarse en la superficie de las muestras. En las organoarcillas resultantes se cuantificó el fenol adsorbido cuando éstas fueron puestas en contacto con diferentes concentraciones de fenol: 50, 500, 1000, 2000, y 2500 mg/l durante 24h. El contaminante sorbido se calculó por medio de cromatografía de gases, y se realizaron aproximaciones con los modelos de Freundllich y Langmuir. El comportamiento de adsorción de fenol en arcillas orgánicas es regido por las características de las muestras. De forma general se puede decir que las muestras de caolines lavados tienen más capacidad de adsorción de fenol que las muestras de arenas de caolín y que la activación alcalina ha proporcionado una mejora en la adsorción de fenol en los dos grupos. En consecuencia se han obtenido materiales adsorbentes heterogéneos y por tanto, con propiedades diferentes. Se ha evaluado el comportamiento global de las arenas de caolín por un lado y del caolín lavado por otro. Las arenas de caolín presentan altos niveles de cuarzo y su uso para ciertos tipos de industrias no son recomendados en ocasiones por el alto costo que el proceso de limpieza y purificación implicaría. Por ello es importante reseñar en este proyecto las aplicaciones que ofrecen algunas muestras de este grupo. Los ensayos acontecidos en esta tesis han dado lugar a las siguientes publicaciones: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno. Aceptada en Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Envío a revista sujeto a la publicación del artículo anterior. ABSTRACT Today’s chemical, pharmaceutical and clinical industries generate pollutants that affect the soils and surface and ground waters of our country. Among these, phenol is a common organic pollutant that is extremely harmful to living organisms, even at low concentrations. Several protocols exist to minimize the effects of pollutants, but most are costly procedures or even generate other pollutants. The adsorption of hazardous materials onto clays is perhaps the most used, efficient and cost-saving method available. However, organic compounds such as phenol are difficult to adsorb and this has led to the development of materials known as organoclays, which are much better at remediating organic compounds. Organoclays are clays that have been modified using a surfactant. In turn, surfactants are organic molecules that confer a cationic rather than anionic charge to the clay surface, improving it’s capacity to adsorb phenol. For this doctorate project, kaolin was selected as an adsorbent material for the removal of phenol given its easy sourcing and relatively low cost. The materials investigated were kaolin sand, a directly extracted material, and washed kaolin, which is the byproduct of the kaolin sand washing process. The main difference between the materials is their quartz content, which is much higher in the kaolin sands. To generate a product from kaolin or kaolin sand capable of retaining organic pollutants such as phenol, both materials were subjected to several heat, chemical and/or mechanical treatments to give rise to compounds with a greater reactive surface area. To this end the two starting materials underwent heating at 750ºC for 3 h, grinding to the point of amorphization and/or activation with HCl 6M or NaOH 5M for 3 h at 90ºC. These treatments gave rise to 18 processed samples, which were characterized in terms of their morphological, mineralogical, and physical-chemical properties. The behaviour of these new materials was examined in terms of their pH, cation exchange capacity (CEC), water adsorption capacity (WCU and WCC), particle size distribution (PSD), specific surface area (SBET), and their X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermal (DTG, DTA) and scanning and transmission electron microscopy (SEM and TEM) properties. The changes conferred by the different treatments were also examined in terms of Al and Si losses. Results for the materials derived from kaolin sands and washed kaolin were similar, with differences attributable to the kaolinite contents of the samples. The treatments heat and grinding produced amorphous materials, which when subjected to acid or alkali activation gave rise to Si and Al losses. This in turn led to a change in physico- chemical, mineralogical and morphological properties. Some samples showed a highly increased surface area and CEC. Further, among the changes produced, alkali treatment led to the generation of zeolites in different proportions depending on the sample. To produce the organoclays, the 18 samples were surfacted with hexadecyltrimethylammonium (HDTMA) 20 mM for 24 h at 60ºC. This surfactant concentration is higher than the CEC of each sample. The amount of HDTMA adsorbed onto the surface of each sample determined by FTIR varied according to treatment. A principle components analysis (PCA) was performed to examine correlations between sample Si/Al ratios and surfactant adsorption capacity. In addition, to explore HDTMA adsorption by the samples, DTG and DTA data were fitted to Freundllich and Langmuir models. The mechanisms of surfactant attachment to the sample surface were also addressed. The amount of phenol adsorbed by the resultant organoclays was determined when exposed to different phenol concentrations: 50, 500, 1000, 2000, and 2500 mg/l for 24 h. The quantity of adsorbed pollutant was estimated by gas chromatography and the data fitted to the models of Freundllich and Langmuir. Results indicate that the phenol adsorption capacity of the surfacted samples is dependent on the sample’s characteristics. In general, the washed kaolin samples showed a greater phenol adsorption capacity than the kaolon sands and alkali activation improved this capacity in the two types of sample. In conclusion, the treatments used gave rise to adsorbent materials with varying properties. Kaolin sands showed high quartz levels and their use in some industries is not recommended due to the costs involved in their washing and purification. The applications suggested by the data obtained for some of the kaolin sand samples indicate the added value of this industrial by-product. The results of this research project have led to the following publications: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G. San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno Accepted in Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Shipment postponed, subject to the publication of the previous article.