Evaluation of the influence of toll systems on energy consumption and CO2 emissions: A case study of a Spanish highway

This paper studies the energy consumption and subsequent CO2 emissions of road highway transportation under three toll systems in Spain for four categories of vehicles: cars, vans, buses and articulated trucks. The influence of toll systems is tested for a section of AP-41 highway between Toledo and Madrid. One system is free flow, other is traditional stop and go and the last toll system operates with an electronic toll collection (ETC) technology. Energy consumption and CO2 emissions were found to be closely related to vehicle mass, wind exposure, engine efficiency and acceleration rate. These parameters affect, directly or indirectly, the external forces which determine the energy consumption. Reducing the magnitude of these forces through an appropriate toll management is an important way of improving the energy performance of vehicles. The type of toll system used can have a major influence on the energy efficiency of highway transportation and therefore it is necessary to consider free flow.

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure

There is strong evidence to indicate that carbon dioxide and other greenhouse gases are accumulating at unprecedented concentrations in out atmosphere contributing to global climate change. Evidence is equally strong that human activities, mainly the burning of fossil fuels, are driving force in this process (IPCC 2007). While different industries contribute varying amounts to total anthropogenic greenhouse gases, it is incumbent upon each to understand its contribution and search for sensible ways to reduce overall greenhouse gas production. The aim of this paper is the development of a methodology to determine the amount of CO2 emissions of a highway, allowing providing solutions that can improve the energy footprint and reduce its emissions

Influence of the composition of natural gas-hydrogen blends (HCNG) on performance an CO2 emissions of a spark ignition engine

Addition of hydrogen to natural gas could be a short-term alternative to nowadays fossil fuels as the emissions of greenhouse gases may be reduced. The aim of this study is to evaluate the performance and emissions of a park ignition engine fuelled with pure natural gas, pure hydrogen and different blends of hydrogen and natural gas (HCNG). The increase of the hydrogen fraction leads to variations in the cylinder pressure and CO2 emissions. In this work, a combustion model based on thermodynamic equations is used considering separated zones for the burned and unburned gases. The results show that the maximum cylinder pressure gets higher as the fraction of hydrogen in the blend increases. The presence of hydrogen in the blend leads to a drecrease in the CO2 emissions. Due to hydrogen properties, leaner fuel-air mixtures can be used along with the appropiate spark timing, leading to an engine emissions improvement without a performance worsening.

CO2 emissions from a spark ignition engine operatin on natural-hydrogen blends (HCNG)

The addition of hydrogen to natural gas could be a short-term alternative to today’s fossil fuels, as greenhouse gas emissions may be reduced. The aim of this study is to evaluate the emissions and performance of a spark ignition engine fuelled by pure natural gas, pure hydrogen, and different blends of hydrogen and natural gas (HCNG). Increasing the hydrogen fraction leads to variations in cylinder pressure and CO2 emissions. In this study, a combustion model based on thermodynamic equations is used, considering separate zones for burned and unburned gases. The results show that the maximum cylinder pressure rises as the fraction of hydrogen in the blend increases. The presence of hydrogen in the blend leads to a decrease in CO2 emissions. Due to the properties of hydrogen, leaner fuel–air mixtures can be used along with the appropriate spark timing, leading to an improvement in engine emissions with no loss of performance.

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure.

The complexity of climate change and its evolution during the last few years has a positive impact on new developments and approaches to reduce the emissions of CO2. Looking for a methodology to evaluate the sustainability of a roadway, a tool has been developed. Life Cycle Assessment (LCA) is being accepted by the road industry to measure and evaluate the environmental impacts of an infrastructure, as the energy consumption and carbon footprint. This paper describes the methodology to calculate the CO2 emissions associated with the energy embodied on a roadway along its life cycle, including construction, operations and demolition. It will assist to find solutions to improve the energy footprint and reduce the amount of CO2 emissions. Details are provided of both, the methodology and the data acquisition. This paper is an application of the methodology to the Spanish highways, using a local database. Two case studies and a practical example are studied to show the model as a decision support for sustainable construction in the road industry.

Investigations on the distribution of air transport traffic and CO2 emissions within the European Union

This study analyses the structure of air traffic and its distribution among the different countries in the European Union, as well as traffic with an origin or destination in non-EU countries. Data sources are Eurostat statistics and actual flight information from EUROCONTROL. Relevant variables such as the number of flights, passengers or cargo tonnes and production indicators (RPKs) are used together with fuel consumption and CO2 emissions data. The segmentation of air traffic in terms of distance permits an assessment of air transport competition with surface transport modes. The results show a clear concentration of traffic in the five larger countries (France, Germany, Italy, Spain and UK), in terms of RPKs. In terms of distance the segment between 500 and 1000 km in the EU, has more flights, passengers, RTKs and CO2 emissions than larger distances. On the environmental side, the distribution of CO2 emissions within the EU Member States is presented, together with fuel efficiency parameters. In general, a direct relationship between RPKs and CO2 emissions is observed for all countries and all distance bands. Consideration is given to the uptake of alternative fuels. Segmenting CO2 emissions per distance band and aircraft type reveals which flights contribute the most the overall EU CO2 emissions. Finally, projections for future CO2 emissions are estimated, according to three different air traffic growth and biofuel introduction scenarios.

Clean Coal Technologies Scenario and Evaluation of Present CO2 Dwindling Initiatives to Approach Zero Emission Power Stations By Coal Combustion. Deployment Situation and Evaluation Study

In the present uncertain global context of reaching an equal social stability and steady thriving economy, power demand expected to grow and global electricity generation could nearly double from 2005 to 2030. Fossil fuels will remain a significant contribution on this energy mix up to 2050, with an expected part of around 70% of global and ca. 60% of European electricity generation. Coal will remain a key player. Hence, a direct effect on the considered CO2 emissions business-as-usual scenario is expected, forecasting three times the present CO2 concentration values up to 1,200ppm by the end of this century. Kyoto protocol was the first approach to take global responsibility onto CO2 emissions monitoring and cap targets by 2012 with reference to 1990. Some of principal CO2emitters did not ratify the reduction targets. Although USA and China spur are taking its own actions and parallel reduction measures. More efficient combustion processes comprising less fuel consuming, a significant contribution from the electricity generation sector to a CO2 dwindling concentration levels, might not be sufficient. Carbon Capture and Storage (CCS) technologies have started to gain more importance from the beginning of the decade, with research and funds coming out to drive its come in useful. After first researching projects and initial scale testing, three principal capture processes came out available today with first figures showing up to 90% CO2 removal by its standard applications in coal fired power stations. Regarding last part of CO2 reduction chain, two options could be considered worthy, reusing (EOR & EGR) and storage. The study evaluates the state of the CO2 capture technology development, availability and investment cost of the different technologies, with few operation cost analysis possible at the time. Main findings and the abatement potential for coal applications are presented. DOE, NETL, MIT, European universities and research institutions, key technology enterprises and utilities, and key technology suppliers are the main sources of this study. A vision of the technology deployment is presented.

A methodology for territorial distribution of CO2 emission reductions in transport sector

Greenhouse gas emission reduction is the pillar of the Kyoto Protocol and one of the main goals of the European Union (UE) energy policy. National reduction targets for EU member states and an overall target for the EU-15 (8%) were set by the Kyoto Protocol. This reduction target is based on emissions in the reference year (1990) and must be reached by 2012. EU energy policy does not set any national targets, only an overall reduction target of 20% by 2020. This paper transfers global greenhouse gas emission reduction targets in both these documents to the transport sector and specifically to CO2 emissions. It proposes a nonlinear distribution method with objective, dynamic targets for reducing CO2 emissions in the transport sector, according to the context and characteristics of each geographical area. First, we analyse CO2 emissions from transport in the reference year (1990) and their evolution from 1990 to 2007. We then propose a nonlinear methodology for distributing dynamic CO2 emission reduction targets. We have applied the proposed distribution function for 2012 and 2020 at two territorial levels (EU member states and Spanish autonomous regions). The weighted distribution is based on per capita CO2 emissions and CO2 emissions per gross domestic product. Finally, we show the weighted targets found for each EU member state and each Spanish autonomous region, compare them with the real achievements to date, and forecast the situation for the years the Kyoto and EU goals are to be met. The results underline the need for ?weighted? decentralised decisions to be made at different territorial levels with a view to achieving a common goal, so relative convergence of all the geographical areas is reached over time. Copyright © 2011 John Wiley & Sons, Ltd.

How lowering speed limits in an urban highway affects traffics performance and emissions: the case of Madrid M-30 ring-road

The city of Madrid keeps not meeting the GHG and air pollutant limits set by the European legislation. A broad range of strategies have being taken into account to reduce both types of emissions; however traffic management meas ures are usually consigned to the sidelines. In 2004, Madrid City Council launched a plan to re-design its inner ring-road supported by a socioeconomic study that evaluated the environmental and operational benefits of the project. For safety reasons the planned speed limit for the tunnel section was finally reduced from 90km/h to 70km/h. Using a Macroscopic Traffic Model and the European Air Pollutant and Emissions Inventory Guidebook (EMEP/EEA), this paper examines the environmental and traffic performance consequences of this decision. Results support the thesis that reduced speed limits leads to GHG and air pollution reductions in the area affected by the measure without substantially altering traffic performance. The implementation of the new speed limit policy brings about a 15% and 16% reduction in both CO2 and NOx emissions respectively. Emissions’ reduction during off-peak hours is larger than during peak hours.

Comparison of CO2 From Coal Capture Processes and Valorisation Technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorising CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorise captured CO2. Valorising captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2 capture and valorising will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Analysis of the Behaviour of Biofuel-Fired Gas Turbine Power Plants

The utilisation of biofuels in gas turbines is a promising alternative to fossil fuels for power generation. It would lead to significant reduction of CO2 emissions using an existing combustion technology, although significant changes seem to be needed and further technological development is necessary. The goal of this work is to perform energy and exergy analyses of the behaviour of gas turbines fired with biogas, ethanol and synthesis gas (bio-syngas), compared with natural gas. The global energy transformation process (i.e. from biomass to electricity) has also been studied. Furthermore, the potential reduction of CO2 emissions attained by the use of biofuels has been determined, considering the restrictions regarding biomass availability. Two different simulation tools have been used to accomplish the aims of this work. The results suggest a high interest and the technical viability of the use of Biomass Integrated Gasification Combined Cycle (BIGCC) systems for large scale power generation.

Comparison of CO2 from coal captureprocesses and valorisation technologies

Coal is the most plentiful and evenly distributed fossil fuel worldwide. Based on current production, it is estimated that the reserves will last approximately 130 years. Its use worldwide has been increasing, mainly due to consumption by emerging countries. CO2 emissions generated by combustion and the repercussions of such on climate change support the view that it could no longer be used. CO2 capture may be the solution to continue using it, which would cater for the growing energy demand worldwide. The aim of this study is to compare different processes concerning CO2 capture that may be economically viable, ultimately showing that coal, a fossil energy source widely distributed around the world, can, as a result of using different CO2 capture processes, be used as a clean source of electricity. Hence, in places where geological hurdles may render the costs of CO2 storage considerably higher, since it might have to travel far, coal may be used for other purposes, thus valorizing CO2 within the industrial sector. This research is focused on the technical and economic comparison of the most relevant CO2 capture projects designed in Spain using different existing technologies. The oxyfuel project in Ciuden (Leon, Spain), the IGCC Elcogas, precombustion CO2-capture project (Puertollano, Spain) and the postcombustion project in Carboneras (Almeria, Spain) will be analyzed in order to assess the options available to valorizecaptured CO2. Valorizing captured CO2 may be an adequate solution in areas where, although CO2 capture is still possible, storage is not equally so, thus generating a further benefit. The possible uses of CO2 will be assessed in vegetable growing greenhouses, harnessing CO2 in vegetable life cycles. This will also be used in growing algae for subsequent biodiesel production. Both CO2capture and valorizing will eventually lead to the clean use of coal, which will thus enhance the level of self-supply, aiding the development of electric vehicles, which require large amounts of electricity, as well as improve the level of energy autonomy in countries around the world. Another type of fuel, biodiesel, will also be obtained, without this affecting international food prices.

Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Emissions and economic costs of cycling compact fluorescent lamps with integrated ballasts

This paper proposes a way to quantify the emissions of mercury (Hg) and CO2 associated with the manufacture and operation of compact fluorescent lamps with integrated ballasts (CFLis), as well as the economic cost of using them under different operating cycles. The main purpose of this paper is to find simple criteria for reducing the polluting emissions under consideration and the economic cost of CFLi to a minimum. A lifetime model is proposed that allows the emissions and costs to be described as a function of degradation from turning CFLi on and their continuous operation. An idealized model of a CFLi is defined that combines characteristics stated by different manufacturers. In addition, two CFLi models representing poor-quality products are analyzed. It was found that the emissions and costs per unit of time of operation of the CFLi depend linearly on the number of times per unit of time it is turned on and the time of continuous operation. The optimal conditions (lowest emissions and costs) depend on the place of manufacture, the place of operation and the quality of the components of the lamp/ballast. Finally, it was also found that for each lamp, there are intervals when it is turned off during which emissions of pollutants and costs are identical regardless of how often the lamp is turned on or the time it remains on. For CO2 emissions, the lamp must be off up to 5 minutes; for the cost, up to 7 minutes and for Hg emissions, up to 43 minutes. It is advisable not to turn on a CFLi sooner than 43 minutes from the last time it was turned off.

Kinetics of CO2 absorption into aqueous solutions in CO2

This research has been performed to emphasize about the problem known as ?climate changes? occurring due to the greenhouse gases emissions (Carbon dioxide (CO2), Methane (CH4),Nitrogen oxides (NOx), Ozone (O3), Chlorofluorocarbons (artificial). Specially, the project will be focused on the CO2 emissions produced mainly from the fossil fuels burning in power plants and other kind of industrial processes. To understand how important the global is warming and therefore the climate change, both the increase of emissions and the evolution of those will be studied in this project drawing conclusions about its effect. The Kyoto Protocol, the most important agreement internationally, signed by a great majority of the industrialized and developed countries, which try to limit the CO2 emissions to the atmosphere, will be cited in this project. Taking into account the effects of global warming and applying the international legislation on emissions of greenhouse gases, a number of measures will be exposed, where the CO2 capture will be studied deeply. Three different kind of CO2 capture technologies will be studied, drawing the conclusion that the post-combustion capture, in particular by amine chemical absorption, is the most efficient one.