Damage assessment on building structures subjected to the recent near-fault earthquake in Lorca (Spain)

The city of Lorca (Spain) was hit on May 11th 2011 by two consecutive earthquakes with 4.6 and 5.2 Mw respectively, causing casualties and important damage in buildings. Lorca is located in the south-east region of Spain and settled on the trace of the Murcia-Totana-Lorca fault. Although the magnitudes of these ground motions were not severe, the damage observed was considerable over a great amount of buildings. More than 300 of them have been demolished and many others are being retrofitted. This paper reports a field study on the damage caused by these earthquakes. The observed damage is related with the structural typology. Further, prototypes of the damaged buildings are idealized with nonlinear numerical models and their seismic behavior and proneness to damage concentration is further investigated through dynamic response analyses.

The time variable in the calculation of building structures. How to extend the working life until the 100 years?

The idea that a building and consequently its structure is for a lifetime has stopped being a reference. CTE establishes that the life utility of a normal construction structure should be of 50years. If the time variable is introduced in the calculation of actions on structures, seems evident thatdifferent values can be used for a standard building, for a provisional structure with ≤ 10 years of life utility or for a monumental building with a life utility of 100 years. The present presentation follows at all moment, the directives and formulations given in the different structural Eurocodes, till the moment not included in the CTE. Finally the values of the actions that must be used to extend the life utility of a building until. 100 years will be deduced, also it suitability and e conomic feasibility will be discuss.

The online case study development for the teaching of building structures reinforcement

The Reinforcement of Building Structures is one of the topics of the Master in Building Innovation Technology (MBIT) of Universidad Politécnica de Madrid (UPM). Since the beginning of the delivery of this master, case studies have been chosen as the teaching methodology. For the 2011-2012 course the online education of this subject was implemented, instead of the classical learning based on attendance. Through ICT’s (Information and Communication Technologies) students are provided with much more and more selective information than through the classical learning. ICT’s can be used for search, enquiries and reporting. Using the online tools has been proved, through the results obtained and based on the surveys made amongst students, to be a successful experience.

Simplified serviceability design of jointless structures. Experimental verification and application to typical bridge and building structures

In this article an experimental campaign aimed at validating a previously published simplified serviceability design method of the columns of long jointless structures is presented. The proposed method is also extended to include tension stiffening effects which proved to be significant in structures with small amount of reinforcement subjected to small axial loading. This extension allows significant improvement of predictions for this type of element. The campaign involved columns with different reinforcement and squashing load ratios, given that these parameters had been identified as crucial when designing columns subjected to imposed displacements. Experimental results are presented and discussed, with particular regard to cracking behaviour and structural stiffness. Considerations on tension stiffening effects are also made. Finally, the application of the method to typical bridge and building cases is presented, showing the feasibility of jointless construction, and the limits which should be respected.

Novel educational assessment for building structures: Automatic evaluation of on-line graphics

This article presents a new automatic evaluation for on-line graphics, its application and the numerous advantages achieved applying this developed correcting method. The software application developed by the Innovation in Education Group “E4”, from the Technical University of Madrid, is oriented for the online self-assessment of the graphic drawings that students carry out as continuous training. The adaptation to the European Higher Educational Area is an important opportunity to research about the possibilities of on-line education assessment. In this way, a new software tool has been developed for continuous self-testing by undergraduates. Using this software it is possible to evaluate the graphical answer of the students. Thus, the drawings made on-line by students are automatically corrected according to the geometry (straight lines, sloping lines or second order curves) and by sizes (depending on the specific values which define the graphics).

Fisuración y deformaciones en tabiquerías

A diferencia de otros parámetros, el efecto de la existencia de huecos en la aparición y desarrollo de los procesos de fisuración en los paños de fábrica no ha sido considerado por las distintas normativas existentes en la actualidad. En nuestros días se emplea una variada gama de tipologías de elementos de cerramiento para realizar las particiones en las obras de edificación, cada una de ellas con características mecánicas diferentes y distinta metodología de ejecución, siendo de aplicación la misma normativa relativa al cálculo y control de las deformaciones. Tal y como expresamos en el Capitulo 1, en el que se analiza el Estado del Conocimiento, los códigos actuales determinan de forma analítica la flecha probable que se alcanza en los elementos portantes estructurales bajo diferentes condiciones de servicio. Las distintas propuestas que existen respecto para la limitación de la flecha activa, una vez realizado el cálculo de las deformaciones, bien por el método de Branson ó mediante los métodos de integración de curvaturas, no contemplan como parámetro a considerar en la limitación de la flecha activa la existencia y tipología de huecos en un paño de fábrica soportado por la estructura. Sin embargo se intuye y podríamos afirmar que una discontinuidad en cualquier elemento sometido a esfuerzos tiene influencia en el estado tensional del mismo. Si consideramos que, de forma general, los procesos de fisuración se producen al superarse la resistencia a tracción de material constitutivo de la fábrica soportada, es claro que la variación tensional inducida por la existencia de huecos ha de tener cierta influencia en la aparición y desarrollo de los procesos de fisuración en los elementos de partición o de cerramiento de las obras de edificación. En los Capítulos 2 y 3 tras justificar la necesidad de realizar una investigación encaminada a confirmar la relación entre la existencia de huecos en un paño de fábrica y el desarrollo de procesos de fisuración en el mismo, se establece este aspecto como principal Objetivo y se expone la Metodología para su análisis. Hemos definido y justificado en el Capítulo 4 el modelo de cálculo que hemos utilizado para determinar las deformaciones y los procesos de fisuración que se producen en los casos a analizar, en los que se han considerado como variables: los valores de la luz del modelo, el estado de fisuración de los elementos portantes, los efectos de la fluencia y el porcentaje de transmisión de cargas desde el forjado superior al paño de fábrica en estudio. Además se adoptan dos valores de la resistencia a tracción de las fábricas, 0.75MPa y 1.00MPa. La capacidad de representar la fisuración, así como la robustez y fiabilidad ha condicionado y justificado la selección del programa de elementos finitos que se ha utilizado para realizar los cálculos. Aprovechando la posibilidad de reproducir de forma ajustada las características introducidas para cada parámetro, hemos planteado y realizado un análisis paramétricos que considera 360 cálculos iterativos, de cuya exposición es objeto el Capítulo 5, para obtener una serie representativa de resultados sobre los que se realizará el análisis posterior. En el Capítulo 6, de análisis de los resultados, hemos estudiado los valores de deformaciones y estados de fisuración obtenidos para los casos analizados. Hemos determinado la influencia que tiene la presencia de huecos en la aparición de los procesos de fisuración y en las deformaciones que se producen en las diferentes configuraciones estructurales. Las conclusiones que hemos obtenido tras analizar los resultados, incluidas en el Capítulo 7, no dejan lugar a dudas: la presencia, la posición y la tipología de los huecos en los elementos de fábricas soportadas sobre estructuras deformables son factores determinantes respecto de la fisuración y pueden tener influencia en las deformaciones que constituyen la flecha activa del elemento, lo que obliga a plantear una serie de recomendaciones frente al proyecto y frente a la reglamentación técnica. La investigación desarrollada para esta Tesis Doctoral y la metodología aplicada para su desarrollo abre nuevas líneas de estudio, que se esbozan en el Capítulo 8, para el análisis de otros aspectos que no han sido cubiertos por esta investigación a fin de mejorar las limitaciones que deberían establecerse para los Estados Límite de Servicio de Deformaciones correspondientes a las estructuras de edificación. SUMMARY. Unlike other parameters, the effect of the existence of voids in the arising and development of cracking processes in the masonry walls has not been considered by current Codes. Nowadays, a huge variety of enclosure elements types is used to execute partitions in buildings, each one with different mechanical characteristics and different execution methodology, being applied the same rules concerning deflection calculation and control. As indicated in Chapter 1, which analyzes the State of Art, current codes analytically determine the deflection likely to be achieved in structural supporting elements under different service conditions. The different proposals that exist related to live deflection limitation, once performed deformations calculation, either by Branson´s method or considering curvatures integration methods, do not consider in deflection limitation the existence and typology of voids in a masonry wall structured supported. But is sensed and it can be affirmed that a discontinuity in any element under stress influences the stress state of it. If we consider that, in general, cracking processes occur when masonry material tensile strength is exceeded, it is clear that tension variation induced by the existence of voids must have some influence on the emergence and development of cracking processes in enclosure elements of building works. In Chapters 2 and 3, after justifying the need for an investigation to confirm the relationship between the existence of voids in a masonry wall and the development of cracking process in it, is set as the main objective and it is shown the analysis Methodology. We have defined and justified in Chapter 4 the calculation model used to determine the deformation and cracking processes that occur in the cases analyzed, in which were considered as variables: model span values, bearing elements cracking state, creep effects and load transmission percentage from the upper floor to the studied masonry wall. In addition, two masonry tensile strength values 0.75MPa and 1.00MPa have been considered. The cracking consideration ability, robustness and reliability has determined and justified the selection of the finite element program that was used for the calculations. Taking advantage of the ability of accurately consider the characteristics introduced for each parameter, we have performed a parametric analyses that considers 360 iterative calculations, whose results are included in Chapter 5, in order to obtain a representative results set that will be analyzed later. In Chapter 6, results analysis, we studied the obtained values of deformation and cracking configurations for the cases analyzed. We determined the influence of the voids presence in the occurrence of cracking processes and deformations in different structural configurations. The conclusions we have obtained after analyzing the results, included in Chapter 7, leave no doubt: the presence, position and type of holes in masonry elements supported on deformable structures are determinative of cracking and can influence deformations which are the element live deflection, making necessary to raise a number of recommendations related to project and technical regulation. The research undertaken for this Doctoral Thesis and the applied methodology for its development opens up new lines of study, outlined in Chapter 8, for the analysis of other aspects that are not covered by this research, in order to improve the limitations that should be established for Deflections Serviceability Limit States related to building structures.

Self-Organizing Architectural design based on Morphogenetic Programming.

In this paper, we present our research into self-organizing building algorithms. This idea of self-organization of animal/plants behaviour interests researchers to explore the mechanisms required for this emergent phenomena and try to apply them in other domains. We were able to implement a typical construction algorithm in a 3D simulation environment and reproduce the results of previous research in the area. LSystems, morphogenetic programming and wasp nest building are explained in order to understand self-organizing models. We proposed Grammatical swarm as a good tool to optimize building structures.

Consideraciones y recomendaciones para el diseño de estructuras bajo amenaza de tsunamis

La visión del riesgo es muy importante a la hora de diseñar y construir estructuras. Sobre todo en presencia de catástrofes naturales. Esta tesis presenta las consideraciones y recomendaciones a tener en cuenta para proyectar estructuras en zonas con riesgo de tsunami, tras haber estudiado todos los riesgos y soluciones posibles mediante tres técnicas diferentes. Esto se ha obtenido aplicando el método LOGRO (Líder de Organización de Gestión de Riesgos y Oportunidades). Se puede pensar que la única solución posible ante esta catástrofe es no construir en zonas vulnerables, pero no es posible. Hay que tener en cuenta que no todos los tsunamis son de la misma magnitud e intensidad y este trabajo contempla todos ellos con distintos niveles de actuación para cada situación. Por otro lado, existen lugares costeros muy urbanizados en los que sería imposible fomentar la emigración, y zonas turísticas donde lo que prima es la cercanía a la costa. Las resultados obtenidos de esta investigación tienen como objetivo reducir el riesgo vinculado al tsunami, minimizando tanto probabilidades de ocurrencia como consecuencias. The hazard view is very important when designing and building structures, mainly, under natural disasters. This thesis presents the considerations and recommendations to take into account to project structures in tsunami prone areas after having studied all the hazards and possible solutions through three different techniques. This has been obtained using LOGRO´s method. It is easy to think that the only possible solution to this disaster is not to build in vulnerable areas, but it is not like this. It has to be taken into account that not all tsunamis are of the same magnitude neither of the same intensity and this work considers all of them with different performance levels for each situation. On the other hand, there are very developed coastal places where it would be impossible to encourage emigration, and touristic areas where the closeness to the coast is what comes first. The aim of the results obtained in this research is to reduce the tsunami hazard minimising not only probabilities but also consequences.

Air Mines. Urban Space Station

Air Mines The sky over the city's port was the color of a faulty screen, only partly lit up. As the silhouette of nearby buildings became darker, but more clearly visible against the fading blur-filter of a background, the realization came about how persistent a change had been taking place. Slowly, old wooden water reservoirs and rattling HVAC systems stopped being the only inhabitants of roofs. Slightly trembling, milkish jellyfish-translucent air volumes had joined the show in multiples. A few years ago artists and architects seized upon the death of buildings as their life-saving media. Equipped with constructive atlases and instruments they started disemboweling their subjects, poking about their systems, dumping out on the street the battered ugliness of their embarrassing bits and pieces, so rightly hidden by facades and height from everyday view. But, would you believe it? Even ?old ladies?, investment bankers or small children failed to get upset. Of course, old ladies are not what they used to be. It was old ladies themselves that made it happen after years of fights with the town hall, imaginative proposals and factual arguments. An industry with little financial gains but lots of welcome externalities was not, in fact, the ground for investment bankers. But they too had to admit that having otherwise stately buildings make fine particulate pencils with their facades was not the worse that could happen. Yes, making soot pencils had been found an interesting and visible end product of the endeavor, a sort of mining the air for vintage writing tools one can actually touch. The new view from the street did not seem as solid or dignified as that of old, and they hated that the market for Fine Particulates Extraction (FPE, read efpee) had to be applied on a matrix of blocks and streets that prevented undue concentration of the best or worse solutions. It had to be an evenly distributed city policy in order for the city to apply for cleaning casino money. Once the first prototypes had been deployed in buildings siding Garden Avenue or Bulwark Street even fast movers appreciated the sidekick of flower and plant smell dripping down the Urban Space Stations (USS, read use; USSs, read uses) as air and walls cooled off for a few hours after sunset. Enough. It was all nice to remember, but it was now time to go up and start the lightweight afternoon maintenance of their USS. Coop discussions had taken place all through the planning and continued through the construction phase as to how maintenance was going to be organized. Fasters had voted for a pro, pay a small amount and let them use it for rent and produce. In the end some neighbors decided they were slow enough to take care and it was now the turn. Regret came periodically, sometimes a week before, and lasted until work actually started. But lately it had been replaced by anxiety when it needed to be passed over to the next caretaker. It did not look their shift was good enough and couldn?t wait to fix it. Today small preparations needed to be made for a class visit next day from a nearby cook school. They were frequenters. It had not been easy, but it shouldn?t have been that hard. In the end, even the easiest things are hard if they involve a city, buildings and neighbors. On the face of the data, the technicalities and the way final designs had been worked out for adaptation to the different settings, the decision of where to go was self evident, but organization issues and the ever-growing politics of taste in a city of already-gentrified-rodents almost put the project in the frozen orbit of timeless beautiful future possibilities. This is how it was. A series of designs by XClinic and OSS had made it possible to adapt to different building structures, leave in most cases the roof untouched and adapted a new technology of flexing fiberglass tubes that dissipated wind pressure in smooth bending.......

Optimización de cimentaciones directas de medianería y esquina mediante modelos de elementos finitos

Existe un amplio catálogo de posibles soluciones para resolver la problemática de las zapatas de medianería así como, por extensión, las zapatas de esquina como caso particular de las anteriores. De ellas, las más habitualmente empleadas en estructuras de edificación son, por un lado, la utilización de una viga centradora que conecta la zapata de medianería con la zapata del pilar interior más próximo y, por otro, la colaboración de la viga de la primera planta trabajando como tirante. En la primera solución planteada, el equilibrio de la zapata de medianería y el centrado de la respuesta del terreno se consigue gracias a la colaboración del pilar interior con su cimentación y al trabajo a flexión de la viga centradora. La modelización clásica considera que se logra un centrado total de la reacción del terreno, con distribución uniforme de las tensiones de contacto bajo ambas zapatas. Este planteamiento presupone, por tanto, que la viga centradora logra evitar cualquier giro de la zapata de medianería y que el pilar puede, por ello, considerarse perfectamente empotrado en la cimentación. En este primer modelo, el protagonismo fundamental recae en la viga centradora, cuyo trabajo a flexión conduce frecuentemente a unas escuadrías y a unas cuantías de armado considerables. La segunda solución, plantea la colaboración de la viga de la primera planta, trabajando como tirante. De nuevo, los métodos convencionales suponen un éxito total en el mecanismo estabilizador del tirante, que logra evitar cualquier giro de la zapata de medianería, dando lugar a una distribución de tensiones también uniforme. Los modelos convencionales existentes para el cálculo de este tipo de cimentaciones presentan, por tanto, una serie de simplificaciones que permiten el cálculo de las mismas, por medios manuales, en un tiempo razonable, pero presentan el inconveniente de su posible alejamiento del comportamiento real de la cimentación, con las consecuencias negativas que ello puede suponer en el dimensionamiento de estos elementos estructurales. La presente tesis doctoral desarrolla un contraste de los modelos convencionales de cálculo de cimentaciones de medianería y esquina, mediante un análisis alternativo con modelos de elementos finitos, con el objetivo de poner de manifiesto las diferencias entre los resultados obtenidos con ambos tipos de modelización, analizar cuáles son las variables que más influyen en el comportamiento real de este tipo de cimentaciones y proponer un nuevo modelo de cálculo, de tipo convencional, más ajustado a la realidad. El proceso de investigación se desarrolla mediante una etapa experimental virtual que utiliza como modelo un pórtico tipo de edificación, ortogonal, de hormigón armado, con dos vanos y número variable de plantas. Tras identificar el posible giro de la cimentación como elemento clave en el comportamiento de las zapatas de medianería y de esquina, se adoptan como variables de estudio aquellas que mayor influencia puedan tener sobre el citado giro de las zapatas y sobre la rigidez del conjunto del elemento estructural. Así, se han estudiado luces de 3 m a 7 m, diferente número de plantas desde baja+1 hasta baja+4, resistencias del terreno desde 100 kN/m2 hasta 300 kN/m2, relaciones de forma de la zapata de medianería de 1,5 : 1 y 2 : 1, aumento y reducción de la cuantía de armado de la viga centradora y variación del canto de la viga centradora desde el mínimo canto compatible con el anclaje de la armadura de los pilares hasta un incremento del 75% respecto del citado canto mínimo. El conjunto de pórticos generados al aplicar las variables indicadas, se ha calculado tanto por métodos convencionales como por el método de los elementos finitos. Los resultados obtenidos ponen de manifiesto importantes discrepancias entre ambos métodos que conducen a importantes diferencias en el dimensionamiento de este tipo de cimentaciones. El empleo de los métodos tradicionales da lugar, por un lado, a un sobredimensionamiento de la armadura de la viga centradora y, por otro, a un infradimensionamiento, tanto del canto de la viga centradora, como del tamaño de la zapata de medianería y del armado de la viga de la primera planta. Finalizado el análisis y discusión de resultados, la tesis propone un nuevo método alternativo, de carácter convencional y, por tanto, aplicable a un cálculo manual en un tiempo razonable, que permite obtener los parámetros clave que regulan el comportamiento de las zapatas de medianería y esquina, conduciendo a un dimensionamiento más ajustado a las necesidades reales de este tipo de cimentación. There is a wide catalogue of possible solutions to solve the problem of party shoes and, by extension, corner shoes as a special case of the above. From all of them, the most commonly used in building structures are, on one hand, the use of a centering beam that connects the party shoe with the shoe of the nearest interior pillar and, on the other hand, the collaboration of the beam of the first floor working as a tie rod. In the first proposed solution, the balance of the party shoe and the centering of the ground response is achieved thanks to the collaboration of the interior pillar with his foundation along with the bending work of the centering beam. Classical modeling considers that a whole centering of the ground reaction is achieved, with uniform contact stress distribution under both shoes. This approach to the issue presupposes that the centering beam manages to avoid any rotation of the party shoe, so the pillar can be considered perfectly embedded in the foundation. In this first model, the leading role lies in the centering beam, whose bending work usually leads to important section sizes and high amounts of reinforced. The second solution, consideres the collaboration of the beam of the first floor, working as tie rod. Again, conventional methods involve a total success in the stabilizing mechanism of the tie rod, that manages to avoid any rotation of the party shoe, resulting in a stress distribution also uniform. Existing conventional models for calculating such foundations show, therefore, a series of simplifications which allow calculation of the same, by manual means, in a reasonable time, but have the disadvantage of the possible distance from the real behavior of the foundation, with the negative consequences this could bring in the dimensioning of these structural elements. The present thesis develops a contrast of conventional models of calculation of party and corner foundations by an alternative analysis with finite element models with the aim of bring to light the differences between the results obtained with both types of modeling, analysis which are the variables that influence the real behavior of this type of foundations and propose a new calculation model, conventional type, more adjusted to reality. The research process is developed through a virtual experimental stage using as a model a typical building frame, orthogonal, made of reinforced concrete, with two openings and variable number of floors. After identifying the possible spin of the foundation as the key element in the behavior of the party and corner shoes, it has been adopted as study variables, those that may have greater influence on the spin of the shoes and on the rigidity of the whole structural element. So, it have been studied lights from 3 m to 7 m, different number of floors from lower floor + 1 to lower floor + 4, máximum ground stresses from 100 kN/m2 300 kN/m2, shape relationships of party shoe 1,5:1 and 2:1, increase and decrease of the amount of reinforced of the centering beam and variation of the height of the centering beam from the minimum compatible with the anchoring of the reinforcement of pillars to an increase of 75% from the minimum quoted height. The set of frames generated by applying the indicated variables, is calculated both by conventional methods such as by the finite element method. The results show significant discrepancies between the two methods that lead to significant differences in the dimensioning of this type of foundation. The use of traditional methods results, on one hand, to an overdimensioning of the reinforced of the centering beam and, on the other hand, to an underdimensioning, both the height of the centering beam, such as the size of the party shoe and the reinforced of the beam of the first floor. After the analysis and discussion of results, the thesis proposes a new alternative method, conventional type and, therefore, applicable to a manual calculation in a reasonable time, that allows to obtain the key parameters that govern the behavior of party and corner shoes, leading to a dimensioning more adjusted to the real needings of this type of foundation.

Límites de ductilidad y de servicio al cálculo en carga última de estructuras de hormigón armado y de fábrica

En este trabajo se aborda una cuestión central en el diseño en carga última de estructuras de hormigón armado y de fábrica: la posibilidad efectiva de que las deformaciones plásticas necesarias para verificar un estado de rotura puedan ser alcanzadas por las regiones de la estructura que deban desarrollar su capacidad última para verificar tal estado. Así, se parte de las decisiones de diseño que mediante mera estática aseguran un equilibrio de la estructura para las cargas últimas que deba resistir, pero determinando directamente el valor de las deformaciones necesarias para llegar a tal estado. Por tanto, no se acude a los teoremas de rotura sin más, sino que se formula el problema desde un punto de vista elastoplástico. Es decir, no se obvia el recorrido que la estructura deba realizar en un proceso de carga incremental monótono, de modo que las regiones no plastificadas contribuyen a coaccionar las libres deformaciones plásticas que, en la teoría de rotura, se suponen. En términos de trabajo y energía, se introduce en el balance del trabajo de las fuerzas externas y en el de la energía de deformación, aquella parte del sistema que no ha plastificado. Establecido así el balance energético como potencial del sistema es cuando la condición de estacionariedad del mismo hace determinados los campos de desplazamientos y, por tanto, el de las deformaciones plásticas también. En definitiva, se trata de un modo de verificar si la ductilidad de los diseños previstos es suficiente, y en qué medida, para verificar el estado de rotura previsto, para unas determinadas cargas impuestas. Dentro del desarrollo teórico del problema, se encuentran ciertas precisiones importantes. Entre ellas, la verificación de que el estado de rotura a que se llega de manera determinada mediante el balance energético elasto-plástico satisface las condiciones de la solución de rotura que los teoremas de carga última predicen, asegurando, por tanto, que la solución determinada -unicidad del problema elásticocoincide con el teorema de unicidad de la carga de rotura, acotando además cuál es el sistema de equilibrio y cuál es la deformada de colapso, aspectos que los teoremas de rotura no pueden asegurar, sino sólo el valor de la carga última a verificar. Otra precisión se basa en la particularidad de los casos en que el sistema presenta una superficie de rotura plana, haciendo infinitas las posibilidades de equilibrio para una misma deformada de colapso determinada, lo que está en la base de, aparentemente, poder plastificar a antojo en vigas y arcos. Desde el planteamiento anterior, se encuentra entonces que existe una condición inherente a cualquier sistema, definidas unas leyes constitutivas internas, que permite al mismo llegar al inicio del estado de rotura sin demandar deformación plástica alguna, produciéndose la plastificación simultánea de todas las regiones que hayan llegado a su solicitación de rotura. En cierto modo, se daría un colapso de apariencia frágil. En tal caso, el sistema conserva plenamente hasta el final su capacidad dúctil y tal estado actúa como representante canónico de cualquier otra solución de equilibrio que con idéntico criterio de diseño interno se prevea para tal estructura. En la medida que el diseño se acerque o aleje de la solución canónica, la demanda de ductilidad del sistema para verificar la carga última será menor o mayor. Las soluciones que se aparten en exceso de la solución canónica, no verificarán el estado de rotura previsto por falta de ductilidad: la demanda de deformación plástica de alguna región plastificada estará más allá de la capacidad de la misma, revelándose una carga de rotura por falta de ductilidad menor que la que se preveía por mero equilibrio. Para la determinación de las deformaciones plásticas de las rótulas, se ha tomado un modelo formulado mediante el Método de los Elementos de Contorno, que proporciona un campo continuo de desplazamientos -y, por ende, de deformaciones y de tensiones- incluso en presencia de fisuras en el contorno. Importante cuestión es que se formula la diferencia, nada desdeñable, de la capacidad de rotación plástica de las secciones de hormigón armado en presencia de cortante y en su ausencia. Para las rótulas de fábrica, la diferencia se establece para las condiciones de la excentricidad -asociadas al valor relativo de la compresión-, donde las diferencias entres las regiones plastificadas con esfuerzo normal relativo alto o bajo son reseñables. Por otro lado, si bien de manera un tanto secundaria, las condiciones de servicio también imponen un límite al diseño previo en carga última deseado. La plastificación lleva asociadas deformaciones considerables, sean locales como globales. Tal cosa impone que, en estado de servicio, si la plastificación de alguna región lleva asociadas fisuraciones excesivas para el ambiente del entorno, la solución sea inviable por ello. Asimismo, las deformaciones de las estructuras suponen un límite severo a las posibilidades de su diseño. Especialmente en edificación, las deformaciones activas son un factor crítico a la hora de decidirse por una u otra solución. Por tanto, al límite que se impone por razón de ductilidad, se debe añadir el que se imponga por razón de las condiciones de servicio. Del modo anterior, considerando las condiciones de ductilidad y de servicio en cada caso, se puede tasar cada decisión de diseño con la previsión de cuáles serán las consecuencias en su estado de carga última y de servicio. Es decir, conocidos los límites, podemos acotar cuáles son los diseños a priori que podrán satisfacer seguro las condiciones de ductilidad y de servicio previstas, y en qué medida. Y, en caso de no poderse satisfacer, qué correcciones debieran realizarse sobre el diseño previo para poderlas cumplir. Por último, de las consecuencias que se extraen de lo estudiado, se proponen ciertas líneas de estudio y de experimentación para poder llegar a completar o expandir de manera práctica los resultados obtenidos. ABSTRACT This work deals with a main issue for the ultimate load design in reinforced concrete and masonry structures: the actual possibility that needed yield strains to reach a ultimate state could be reached by yielded regions on the structure that should develop their ultimate capacity to fulfill such a state. Thus, some statically determined design decisions are posed as a start for prescribed ultimate loads to be counteracted, but finding out the determined value of the strains needed to reach the ultimate load state. Therefore, ultimate load theorems are not taken as they are, but a full elasto-plastic formulation point of view is used. As a result, the path the structure must develop in a monotonus increasing loading procedure is not neglected, leading to the fact that non yielded regions will restrict the supposed totally free yield strains under a pure ultimate load theory. In work and energy terms, in the overall account of external forces work and internal strain energy, those domains in the body not reaching their ultimate state are considered. Once thus established the energy balance of the system as its potential, by imposing on it the stationary condition, both displacements and yield strains appear as determined values. Consequently, what proposed is a means for verifying whether the ductility of prescribed designs is enough and the extent to which they are so, for known imposed loads. On the way for the theoretical development of the proposal, some important aspects have been found. Among these, the verification that the conditions for the ultimate state reached under the elastoplastic energy balance fulfills the conditions prescribed for the ultimate load state predicted through the ultimate load theorems, assuring, therefore, that the determinate solution -unicity of the elastic problemcoincides with the unicity ultimate load theorem, determining as well which equilibrium system and which collapse shape are linked to it, being these two last aspects unaffordable by the ultimate load theorems, that make sure only which is the value of the ultimate load leading to collapse. Another aspect is based on the particular case in which the yield surface of the system is flat -i.e. expressed under a linear expression-, turning out infinite the equilibrium possibilities for one determined collapse shape, which is the basis of, apparently, deciding at own free will the yield distribution in beams and arches. From the foresaid approach, is then found that there is an inherent condition in any system, once defined internal constitutive laws, which allows it arrive at the beginning of the ultimate state or collapse without any yield strain demand, reaching the collapse simultaneously for all regions that have come to their ultimate strength. In a certain way, it would appear to be a fragile collapse. In such a case case, the system fully keeps until the end its ductility, and such a state acts as a canonical representative of any other statically determined solution having the same internal design criteria that could be posed for the that same structure. The extent to which a design is closer to or farther from the canonical solution, the ductility demand of the system to verify the ultimate load will be higher or lower. The solutions being far in excess from the canonical solution, will not verify the ultimate state due to lack of ductility: the demand for yield strains of any yielded region will be beyond its capacity, and a shortcoming ultimate load by lack of ductility will appear, lower than the expected by mere equilibrium. For determining the yield strains of plastic hinges, a Boundary Element Method based model has been used, leading to a continuous displacement field -therefore, for strains and stresses as well- even if cracks on the boundary are present. An important aspect is that a remarkable difference is found in the rotation capacity between plastic hinges in reinforced concrete with or without shear. For masonry hinges, such difference appears when dealing with the eccentricity of axial forces -related to their relative value of compression- on the section, where differences between yield regions under high or low relative compressions are remarkable. On the other hand, although in a certain secondary manner, serviceability conditions impose limits to the previous ultimate load stated wanted too. Yield means always big strains and deformations, locally and globally. Such a thing imposes, for serviceability states, that if a yielded region is associated with too large cracking for the environmental conditions, the predicted design will be unsuitable due to this. Furthermore, displacements must be restricted under certain severe limits that restrain the possibilities for a free design. Especially in building structures, active displacements are a critical factor when chosing one or another solution. Then, to the limits due to ductility reasons, other limits dealing with serviceability conditions shoud be added. In the foresaid way, both considering ductility and serviceability conditions in every case, the results for ultimate load and serviceability to which every design decision will lead can be bounded. This means that, once the limits are known, it is possible to bound which a priori designs will fulfill for sure the prescribed ductility and serviceability conditions, and the extent to wich they will be fulfilled, And, in case they were not, which corrections must be performed in the previous design so that it will. Finally, from the consequences derived through what studied, several study and experimental fields are proposed, in order to achieve a completeness and practical expansion of the obtained results.

Building ontologies from folksonomies and linked data: Data structures and Algorithms

We present the data structures and algorithms used in the approach for building domain ontologies from folksonomies and linked data. In this approach we extracts domain terms from folksonomies and enrich them with semantic information from the Linked Open Data cloud. As a result, we obtain a domain ontology that combines the emergent knowledge of social tagging systems with formal knowledge from Ontologies.

Specific skills assessment learned by students of building engineering and technical architecture in topics relating to durability and control of concrete structures

In many university courses such as Building Engineering or Technical Architectural, the high density of the contents included in the curriculum, make the student, after graduation, unable to develop the skills already acquired and evaluated in the disciplines of the first courses. From the Group of Educational Innovation at the Polytechnic University of Madrid (UPM) "Teaching of Structural Concrete" (GIEHE) we have conducted a study in which are valued specific skills acquired by students after the first courses of career. We have worked with students from UPM fourth-year career and with Technical Architecture students who have completed their studies and also have completed the Adaptation Course of Technical Architecture to the Building Engineer. The work is part of the Educational Innovation Project funded by the UPM "Integration of training and assessment of generic and specific skills in structural concrete" We have evaluated specific skills learned in the areas of durability and control of structural concrete structures. The results show that overall, students are not able to fully develop the skills already acquired earlier, even being these essential to their professional development. Possibly, the large amount of content taught in these degrees together with a teaching and assessment of "flat profile", ie, which are presented and evaluated with the same intensity as the fundamental and the accessory, are causes enough to cause these results.

Bending continuous structures with SMAs: a novel robotic fish design

In this paper, we describe our research on bio-inspired locomotion systems using deformable structures and smart materials, concretely shape memory alloys (SMAs). These types of materials allow us to explore the possibility of building motor-less and gear-less robots. A swimming underwater fish-like robot has been developed whose movements are generated using SMAs. These actuators are suitable for bending the continuous backbone of the fish, which in turn causes a change in the curvature of the body. This type of structural arrangement is inspired by fish red muscles, which are mainly recruited during steady swimming for the bending of a flexible but nearly incompressible structure such as the fishbone. This paper reviews the design process of these bio-inspired structures, from the motivations and physiological inspiration to the mechatronics design, control and simulations, leading to actual experimental trials and results. The focus of this work is to present the mechanisms by which standard swimming patterns can be reproduced with the proposed design. Moreover, the performance of the SMA-based actuators’ control in terms of actuation speed and position accuracy is also addressed.

Dynamique des structures. Vulnérabilité aux bâtiments. Construction parasismique

La leçon s'addresse à la comprehension du comportement des bâtiments soumis à l'accéleration séismique, et présente une introduction au comportement dynamique de oscillateurs (un ou plusieurs dégrés de liberté), du comportément hystérétique des structures (selon modes de dissipation) et aux paramètres séismiques relevants à la conception parasismique, notamment aux spectres de réponse et de démande, et sa relation avec la capacité de la structure (courbe de capacité) où on peut identifier les niveaux de dommage -ou les critères de performance- pour des intensités séismique prévues au projet. Elle considère aussi les méthodes de définition et détermination de la vulnérabilité, façe aux séismes, des différentes typologies constructives, avec l'inclusion finale des typologies pour les sistèmes de contreventement et recomandations visées à éviter aux mêmes la concentration de dommage d'origine séismique. Lecture's goal focuses in the understanding of the behaviour of buildings under seismic excitation. It presents an introduction of dynamics (single or multiple degrees of freedom oscillators) and the hysteretic behaviour of ductile structures, introducing the seismic parameters relevant to the structural design, mostly in the context of response and demand spectra and their relations with capacity curves of structures. On the capacity curve obtained in pushover analysis, points representing the design objectives in terms of performance levels can be identified and related with seismic demand. Lecture deals also with methods on vulnerability analysis for building construction typologies and the behaviour (and related recommendations) of seismic resistant structural typologies, having the distribution of dissipative energy and damage in mind.