The Effect of Sequence of Operations on Fatigue Life of LSP Treated Open-hole Aluminium Specimens

Fastener holes in aeronautical structures are typical sources of fatigue cracks due to their induced local stress concentration. A very efficient solution to this problem is to establish compressive residual stresses around the fastener holes that retard the fatigue crack nucleation and its subsequent local propagation. Previous work done on the subject of the application of LSP treatment on thin, open-hole specimens [1] has proven that the LSP effect on fatigue life of treated specimens can be detrimental, if the process is not properly optimized. In fact, it was shown that the capability of the LSP to introduce compressive residual stresses around fastener holes in thin-walled structures representative of typical aircraft constructions was not superior to the performance of conventional techniques, such as cold-working.

Fatigue in laser shock peened open-hole thin aluminium specimens

An experimental study was performed in order to determine the influence of the sequence of operations on the effectiveness of Laser Shock Peening (LSP) treatment in increasing the fatigue performances of open-hole aluminium specimens. Residual stress measurements, fractographic analysis and FEM analysis were performed, indicating the presence of compressive residual stresses on the surface of the treated specimens and tensile residual stresses in the mid-section along the thickness of the specimens. Negative effects on fatigue lives were encountered on the specimens with the hole already present, while positive effect were observed in specimens in which the hole was drilled after LSP treatment. These results indicate that LSP can be a good solution for “in production” application, in which open holes are to be drilled after the LSP treatment. The application in which LSP is used “in service” on structures with pre-existing cut-outs, has proven to be impracticable in the investigated configuration.

Packaging and testing of fiber Bragg gratings for use as strain sensor for rock specimens

This paper reports a packaging and calibration procedure for surface mounting of fiber Bragg grating (FBG) sensors to measure strain in rocks. The packaging of FBG sensors is performed with glass fiber and polyester resin, and then subjected to tensile loads in order to obtain strength and deformability parameters, necessaries to assess the mechanical performance of the sensor packaging. For a specific package, an optimal curing condition has been found, showing good repeatability and adaptability for non-planar surfaces, such as occurs in rock engineering. The successfully packaged sensors and electrical strain gages were attached to standard rock specimens of gabbro. Longitudinal and transversal strains under compression loads were measured with both techniques, showing that response of FBG sensors is linear and reliable. An analytical model is used to characterize the influences of rock substrate and FBG packaging in strain transmission. As a result, we obtained a sensor packaging for non-planar and complex natural material under acceptable sensitivity suitable for very small strains as occurs in hard rocks.

The Cohesive Crack Model Applied To Notched PMMA Specimens Obeying a Non Linear Behaviour Under Torsion Loading

This article presents a new material model developed with the aim of analyzing failure of blunt notched components made of nonlinear brittle materials. The model, which combines the cohesive crack model with Hencky's theory of total deformations, is used to simulate an experimental benchmark carried out previously by the authors. Such combination is achieved through the embedded crack approach concept. In spite of the unavailability of precise material data, the numerical predictions obtained show good agreement with the experimental results.

Estudios corológicos de plantas vasculares en la cuenca media del Tajo

Se ha realizado un estudio de la distribución de plantas vasculares en un territorio situado entre las provincias de Cuenca, Guadalajara, Madrid y Toledo (España). El territorio estudiado está en la Submeseta Sur de la península ibérica, al sur del Sistema Central, norte de los Montes de Toledo y oeste del Sistema Ibérico, en zonas sedimentarias con poco relieve y clima mediterráneo, con grandes contrastes de temperatura y precipitaciones muy irregulares. Coincide con las regiones naturales llamadas: “Alcarrias”, “Campiñas de Madrid y Guadalajara” y “Vegas de los ríos de la Cuenca del Tajo”. Es lo que he llamado Cuenca Media del Tajo. En una primera fase se ha estudiado la flora regional para adquirir conocimientos previos mediante las consultas bibliográficas y de herbarios, se ha contado con bases de datos disponibles para MA, MACB, MAF, JACA, AH, ABH, VAL, SALA y EMMA. Se han revisado las aportaciones propias que en los últimos años he realizado en el territorio en relación a los temas tratados en la tesis. El trabajo de campo ha consistido en la realización de inventarios de presencia de flora. Ha sido muy importante la tarea herborizadora para llegar a la correcta identificación de las especies colectadas en los inventarios. De esta forma el autor ha confeccionado un herbario propio JML que en el territorio muestreado ha reunido cerca de 15000 números en las cuatro provincias estudiadas. Se ha hecho un muestreo sistemático del territorio con unos 6000 listados de plantas. Se ha tomado como unidad de muestreo la cuadrícula de UTM de 1 km de lado incluida como una centésima parte de la cuadrícula de UTM de 10 km. Se han seguido criterios para uniformizar el muestreo. Se ha apuntado el tiempo empleado y la superficie muestreada estimada en cada toma de datos. El criterio mínimo que tienen que cumplir todas las cuadrículas en el área estudiada ha sido que para cada cuadrícula de UTM de 5 km se han realizado al menos 5 inventarios en 5 cuadrículas diferentes de UTM de 1 km y al menos en una hora de tiempo. La unidad de comparación ha sido la cuadrícula UTM de 5 km. Se han informatizado los inventarios de campo, para ello se ha creado la base de datos TESIS en Microsoft office –Access-. Las principales tablas son LOCALIDAD, en la que se anotan las características del lugar muestreado y ESPECIES, que lista las especies de flora consideradas en las cuatro provincias del estudio. Por medio de formularios se han rellenado las tablas; destaca la tabla ESPECIE INVENTARIO que relaciona las tablas ESPECIES y LOCALIDAD; esta tabla cuenta en este momento con unos 165.000 registros. En la tabla ESPECIES_FPVI se visualizan las especies recopiladas. Se ha creado un indicador llamado FPVI “Flora permanentemente visible identificable” que consiste en atribuir a cada especie unos índices que nos permiten saber si una determinada planta se puede detectar en cualquier época del año. Los resultados presentados son: Creación de la base de datos TESIS. El Catálogo Florístico de la Cuenca Media del Tajo, que es el catálogo de la flora de las cuatro provincias desde el principio de la sistemática hasta las Saxifragáceas. En total se han recopilado 1028 taxones distribuidos en 77 familias. Se ha calculado el índice FPVI, para las especies del catálogo. La finalidad para la que se ha diseñado este índice es para poder comparar territorios. Para el desarrollo de ambos resultados ha sido fundamental el desarrollo de la tabla ESPECIES_PVI de la base de datos TESIS. En la tabla ESPECIES_PVI se han apuntado las características ecológicas y se revisa la información bibliográfica disponible para cada especie; las principales fuentes de información consultadas han sido Flora iberica, el proyecto “Anthos” y las bases de datos de los herbarios. Se ha apuntado sí se ha visto, sí está protegida o sí en un endemismo. Otros resultados son: la localización de las cuadrículas de UTM de 10 km, con mayor número de endemismos o especies singulares, con mayor valor botánico. Se ha realizado un par de ejemplos de estudios de autoecología de especie, en concreto Teucrium pumilum y Clematis recta. Se han confeccionando salidas cartográficas de distribución de especies. Se ha elaborado el herbario JML. Se ha presentado una sencilla herramienta para incluir inventarios florísticos, citas corológicas, consultas de autoecología o etiquetado de pliegos de herbario. Como colofón, se ha colaborado para desarrollar una aplicación informática de visualización, análisis y estudio de la distribución de taxones vegetales, que ha utilizado como datos de partida un porcentaje importante de los obtenidos para esta tesis. ABSTRACT I have made a study of the distribution of vascular plants in a territory located between the provinces of Cuenca, Guadalajara, Madrid and Toledo (Spain). The studied area is in the “Submeseta” South of the Iberian Peninsula, south of the Central System, north of the Montes de Toledo and west of the Iberian System, in sedimentary areas with little relief and Mediterranean climate, with big temperature contrasts and irregular rainfall. Coincides with the natural regions called "Alcarrias", "countryside of Madrid and Guadalajara" and “Vegas River Tagus Basin”. This is what I have called Middle Tagus Basin. In a first step we have studied the regional flora to acquire prior knowledge through the literature and herbaria consultations, it has had available databases for MA, MACB, MAF, JACA, AH, ABH, VAL, SALA and EMMA herbaria. The contributions I have made in the last years in the territory in relation to the topics discussed in the thesis have been revised. The field work consisted of conducting inventories presence of flora. Botanize was a very important task to get to the correct identification of the species collected in inventories. In this way the author has made his own herbarium JML in the sampled area has met at least 15000 samples in the four studied provinces. There has been a systematic sampling of the territory with nearly 6,000 listings of plants. Was taken as the sampling unit grid UTM 1 km side included as a hundredth of the UTM grid of 10 km from side. Criteria have been taken to standardize the sampling. Data were taken of the time spent and the estimated sampled surface. The minimum criteria they have to meet all the grids in the study area has been that for each UTM grid of 5 km have been made at least 5 stocks in 5 different grids UTM 1 km and at least one hour of time. The unit of comparison was the UTM grid of 5 km. I have computerized inventories of field, for it was created a database in Access- Microsoft office -TESIS. The main tables are LOCALIDAD, with caracteristics of the sampled location and ESPECIES, which lists the plant species considered in the four provinces of the study, is. Through forms I filled in the tables; highlights ESPECIE INVENTARIO table that relates the tables ESPECIES and LOCALIDAD, this table is counted at the moment with about 165,000 records. The table ESPECIES FPVI visualizes all recollected species. We have created an indicator called FPVI "Flora permanently visible identifiable" that attributes to each species indices that allow us to know whether a given plant can be detected in any season. The results presented are: Creating data base TESIS. The Floristic Books Middle Tagus Basin, which is a catalog of the flora of the four provinces since the beginning of the systematic until Saxifragaceae. In total 1028 collected taxa in 77 families. We calculated FPVI index for species catalog. The purpose for which this index designed is, to compare territories. For the development of both results, it was essential to develop the table ESPECIES_PVI TESIS data base. Table ESPECIES_PVI has signed the ecological characteristics and bibliographic information available for each species is revised; the main sources of information has been Flora iberica, the Anthos project databases of herbaria. Targeted species has been recorded, when seen, protected or endemism. Have also been located UTM grids of 10 km, with the largest number of endemic or unique species and more botanical value. There have been a couple of species autecology studies, namely Teucrium pumilum and Clematis recta, as an example of this type of study. They have been putting together maps of species distribution. We made herbarium JML. I have presented a simple tool to include floristic inventories, chorological appointments, consultations or to tag autoecology herbarium specimens. To cap it has worked to develop a computer application for visualization, analysis and study of the distribution of plant taxa, which has used as input data a significant percentage of those obtained for this thesis.

Development and Testing of a Fiber Bragg Grating Strain Sensor for Uniaxial Compression of Rock Specimens

Los sensores de fibra óptica son una tecnología que ha madurado en los últimos años, sin embargo, se requiere un mayor desarrollo de aplicaciones para materiales naturales como las rocas, que por ser agregados complejos pueden contener partículas minerales y fracturas de tamaño mucho mayor que las galgas eléctricas usadas tradicionalmente para medir deformaciones en las pruebas de laboratorio, ocasionando que los resultados obtenidos puedan ser no representativos. En este trabajo fueron diseñados, fabricados y probados sensores de deformación de gran área y forma curvada, usando redes de Bragg en fibra óptica (FBG) con el objetivo de obtener registros representativos en rocas que contienen minerales y estructuras de diversas composiciones, tamaños y direcciones. Se presenta el proceso de elaboración del transductor, su caracterización mecánica, su calibración y su evaluación en pruebas de compresión uniaxial en muestras de roca. Para verificar la eficiencia en la transmisión de la deformación de la roca al sensor una vez pegado, también fue realizado el análisis de la transferencia incluyendo los efectos del adhesivo, de la muestra y del transductor. Los resultados experimentales indican que el sensor desarrollado permite registro y transferencia de la deformación fiables, avance necesario para uso en rocas y otros materiales heterogénos, señalando una interesante perspectiva para aplicaciones sobre superficies irregulares, pues permite aumentar a voluntad el tamaño y forma del área de registro, posibilita también obtener mayor fiabilidad de resultados en muestras de pequeño tamaño y sugiere su conveniencia en obras, en las cuales los sistemas eléctricos tradicionales tienen limitaciones. ABSTRACT Optical fiber sensors are a technology that has matured in recent years, however, further development for rock applications is needed. Rocks contain mineral particles and features larger than electrical strain gauges traditionally used in laboratory tests, causing the results to be unrepresentative. In this work were designed, manufactured, and tested large area and curved shape strain gages, using fiber Bragg gratings in optical fiber (FBG) in order to obtain representative measurement on surface rocks samples containing minerals and structures of different compositions, sizes and directions. This reports presents the processes of manufacturing, mechanical characterization, calibration and evaluation under uniaxial compression tests on rock samples. To verify the efficiency of rock deformation transmitted to attached sensor, it was also performed the analysis of the strain transfer including the effects of the bonding, the sample and the transducer. The experimental results indicate that the developed sensor enables reliable measurements of the strain and its transmission from rock to sensor, appropriate for use in heterogeneous materials, pointing an interesting perspective for applications on irregular surfaces, allowing increasing at will the size and shape of the measurement area. This research suggests suitability of the optical strain gauge for real scale, where traditional electrical systems have demonstrated some limitations.